In a thick-cylinder pressurized from inside, the hoop stress is maximum at a) The center of the wall thickness b) the outer radius c) the inner radius d) both the inner and the outer radii

In a thick-cylinder pressurized from inside, the hoop stress is maximum at  a) The center of the wall thickness  
b) the outer radius  
c) the inner radius  
d) both the inner and the outer radii
by

1 Answer

Answer :

c) the inner radius
by

Related questions

In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum at the inner surface and minimum at the outer surface c) maximum at the inner surface and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Description : In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum ... and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Last Answer : c) maximum at the inner surface and zero at the outer surface

A thick cylinder under pi and po will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Description : A thick cylinder under pi and po will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Last Answer : 2. Inner radius

A thick cylinder under internal fluid pressure’ pi will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Description : A thick cylinder under internal fluid pressure’ pi will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Last Answer : 2. Inner radius

A thick cylinder under external fluid pressure’ p0′ will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Description : A thick cylinder under external fluid pressure’ p0′ will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Last Answer : 2. Inner radius

A thick cylinder is subjected to an internal pressure of 60 MPa. If the hoop stress on the outer surface is 150 MPa, then the hoop stress on the internal surface is a) 105 MPa b) 180 MPa c) 210 MPa d) 135 MPa.

Description : A thick cylinder is subjected to an internal pressure of 60 MPa. If the hoop stress on the outer surface is 150 MPa, then the hoop stress on the internal surface is a) 105 MPa b) 180 MPa c) 210 MPa d) 135 MPa.

Last Answer : c) 210 MPa

A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these

Description : A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these

Last Answer : (c) outer surface of shaft

Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Description : Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Last Answer : b) Thick Cylinders

Which of the following is incorrect? a. In a solid shaft maximum shear stress occurs at radius = radius of shaft b. In a solid shaft maximum shear stress occurs at center c. In a hollow shaft maximum shear stress occurs at outer radius d. In a hollow shaft minimum shear stress occurs at inner radius

Description : Which of the following is incorrect? a. In a solid shaft maximum shear stress occurs at radius = radius of shaft b. In a solid shaft maximum shear stress occurs at center c. In a hollow ... maximum shear stress occurs at outer radius d. In a hollow shaft minimum shear stress occurs at inner radius

Last Answer : b. In a solid shaft maximum shear stress occurs at center

A vessel is said to be thin if a. Its wall has less thickness b. Stresses are uniform over the entire thickness c. Stresses vary at inner and at outer radius d. None of the above

Description : A vessel is said to be thin if a. Its wall has less thickness b. Stresses are uniform over the entire thickness c. Stresses vary at inner and at outer radius d. None of the above

Last Answer : b. Stresses are uniform over the entire thickness

Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.

Description : Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.

Last Answer : c. At the outer surface of the shaft.

A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Description : A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Last Answer : (c) 286 Mpa

A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Description : A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Last Answer : b) 5 cm

Hoop shrinking in thick cylinders is done to achieve (a) Increased stresses (b) Decreased stresses (c ) Uniform stresses (d) None

Description : Hoop shrinking in thick cylinders is done to achieve (a) Increased stresses (b) Decreased stresses (c ) Uniform stresses (d) None

Last Answer : Hoop shrinking technique is used to make the stresses on the cylinder walls evenly distributed around the circumference of the cylinder, which results in a uniform stress distribution. This is important for ... under load. It also makes sure that the cylinder can withstand the pressure inside it.

The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame’s equation. Diameter of the cylinder is 40mm and pressure in cylinder is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Description : The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame's equation. Diameter of the cylinder is 40mm and ... is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Last Answer : c) 5.07mm

What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Last Answer : c. 20.120 N/mm2

What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Description : What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Last Answer : c. 1:2

Find the magnetic field intensity at the radius of 6cm of a coaxial cable with inner and outer radii are 1.5cm and 4cm respectively. The current flowing is 2A. a) 2.73 b) 3.5 c) 0 d) 1.25

Description : Find the magnetic field intensity at the radius of 6cm of a coaxial cable with inner and outer radii are 1.5cm and 4cm respectively. The current flowing is 2A. a) 2.73 b) 3.5 c) 0 d) 1.25

Last Answer : c) 0

If is the internal pressure in a thin cylinder of diameter and thickness , the developed hoop stress, is (A) pd/2t (B) pd/4t (C) pd/t (D) 2pd/t

Description : If is the internal pressure in a thin cylinder of diameter and thickness , the developed hoop stress, is (A) pd/2t (B) pd/4t (C) pd/t (D) 2pd/t

Last Answer : (A) pd/2t

The maximum strain in a thick cylinder under pi will be a) σh/E+μ σl/E b) σh/ E+ μσr/E c) σr/E+μ σl/E d) None

Description : The maximum strain in a thick cylinder under pi will be a) σh/E+μ σl/E b) σh/ E+ μσr/E c) σr/E+μ σl/E d) None

Last Answer : b) σh/ E+ μσr/E

Lame’s equation used to find the thickness of the cylinder is based on maximum strain failure. a) True b) False

Description : Lame’s equation used to find the thickness of the cylinder is based on maximum strain failure. a) True b) False

Last Answer : b) False

A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of rigidity is 80 GPa. The outside diameter (in mm) of the shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Last Answer : (a) 43 to 45

Design of a thin shell under pressure is done on the basis of a. Radial stress b. Longitudinal stress c. Hoop stress d. All the three stresses

Description : Design of a thin shell under pressure is done on the basis of a. Radial stress b. Longitudinal stress c. Hoop stress d. All the three stresses

Last Answer : c. Hoop stress

Which stress is the least in a thin shell a. Longitudinal stress b. Hoop stress c. Radial stress d. None

Description : Which stress is the least in a thin shell a. Longitudinal stress b. Hoop stress c. Radial stress d. None

Last Answer : c. Radial stress

Hoop stress in a thin vessel is a. pD/2t b. pD/4t c. pD/3t d. None

Description : Hoop stress in a thin vessel is a. pD/2t b. pD/4t c. pD/3t d. None

Last Answer : a. pD/2t

The stress in the wall of a cylinder in a direction normal to its longitudinal axis, due to a force acting along the circumference, is known as (A) Yield stress(B) Longitudinal stress (C) Hoop stress (D) Circumferential stress

Description : The stress in the wall of a cylinder in a direction normal to its longitudinal axis, due to a force  acting along the circumference, is known as  (A) Yield stress  (B) Longitudinal stress  (C) Hoop stress  (D) Circumferential stress 

Last Answer : (C) Hoop stress

Stress in the cross section of a shaft at the centre ________ a. is zero b. decreases linearly to the maximum value of at outer surface c. both a. and b. d. none of the above

Description : Stress in the cross section of a shaft at the centre ________ a. is zero b. decreases linearly to the maximum value of at outer surface c. both a. and b. d. none of the above

Last Answer : a. is zero

The shear stress is minimum at (a) Axis of the shaft (b) Outer surface of the shaft (c) Anywhere inside the shaft (d) None of these

Description : The shear stress is minimum at (a) Axis of the shaft (b) Outer surface of the shaft (c) Anywhere inside the shaft (d) None of these

Last Answer : (c) Anywhere inside the shaft

The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Description : The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Last Answer : a. 15/16

A hemispherical bowl is made of steel, 0.25 cm thick. The inner radius of the bowl is 5cm. Find the outer curved surface of the bowl. -Maths 9th

Description : A hemispherical bowl is made of steel, 0.25 cm thick. The inner radius of the bowl is 5cm. Find the outer curved surface of the bowl. -Maths 9th

Last Answer : Inner radius of hemispherical bowl = 5cm Thickness of the bowl = 0.25 cm Outer radius of hemispherical bowl = (5+0.25) cm = 5.25 cm Formula for outer CSA of hemispherical bowl = 2πr2, where r is radius of ... 22/7) (5.25)2 = 173.25 Therefore, the outer curved surface area of the bowl is 173.25 cm2.

The maximum value of hoop compression in a dome is given by (A) wR / 4d (B) wR/2d (C) wR/d (D) 2wR/d Where, w = load per unit area of surface of dome R = radius of curvature d = thickness of dome

Description : The maximum value of hoop compression in a dome is given by (A) wR / 4d (B) wR/2d (C) wR/d (D) 2wR/d Where, w = load per unit area of surface of dome R = radius of curvature d = thickness of dome

Last Answer : (B) wR/2d

Maximum shear stress in a thick shell is a) (σh+ σl)/2 b) (σh+ σr)/2 c) (σh– σl)/2 d) None

Description : Maximum shear stress in a thick shell is a) (σh+ σl)/2 b) (σh+ σr)/2 c) (σh– σl)/2 d) None

Last Answer : b) (σh+ σr)/2

The potential of a coaxial cylinder with charge density 1 unit , inner radius 1m and outer cylinder 2m is (in 10 9 ) a) 12.74 b) 13.47 c) 12.47 d) 13.74

Description : The potential of a coaxial cylinder with charge density 1 unit , inner radius 1m and outer cylinder 2m is (in 10 9 ) a) 12.74 b) 13.47 c) 12.47 d) 13.74

Last Answer : c) 12.47

A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm

Description : A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm

Last Answer : b) 2.5cm

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Last Answer : c) 8mm

The torque transmitted by a hollow shaft of outer diameter (D) and inner diameter (d) (a)π/4fs(D2-d2)/D (b) π/4fs(D3-d3)/D (c) π/4fs(D4-d4)/D (d) π/4fs(D4-d4)/D

Description : The torque transmitted by a hollow shaft of outer diameter (D) and inner diameter (d) (a)π/4fs(D2-d2)/D (b) π/4fs(D3-d3)/D (c) π/4fs(D4-d4)/D (d) π/4fs(D4-d4)/D

Last Answer : (c) π/4fs(D4-d4)/D

The polar moment of inertia of a hollow shaft of outer diameter (D) and inner diameter (d) is given by. (a)π/16(D3-d3) (b) π/16(D4-d4) (c) π/16(D4-d4) (d) π/16(D4-d4/d)

Description : The polar moment of inertia of a hollow shaft of outer diameter (D) and inner diameter (d) is given by. (a)π/16(D3-d3) (b) π/16(D4-d4) (c) π/16(D4-d4) (d) π/16(D4-d4/d)

Last Answer : (b) π/16(D4-d4)

A hollow circular tube with a 2.3-cm I.D. and 2.5-cm O.D. is rigidly supported at its ends. A 2.5 kN-m torque is applied at the center of this tube. What is the maximum shear stress acting on this tube? (a) 2.87Mpa (b) 4.27 Mpa (c) 6.92 Mpa (d) 10.2 Mpa

Description : A hollow circular tube with a 2.3-cm I.D. and 2.5-cm O.D. is rigidly supported at its ends. A 2.5 kN-m torque is applied at the center of this tube. What is the maximum shear stress acting on this tube? (a) 2.87Mpa (b) 4.27 Mpa (c) 6.92 Mpa (d) 10.2 Mpa

Last Answer : (a) 2.87Mpa

Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Description : Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Last Answer : b. 105.4 mm

A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Description : A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Last Answer : (d) 27/p

The outer and the inner radii of a hollow sphere are 12 cm and 10 cm. Find its volume. -Maths 9th

Description : The outer and the inner radii of a hollow sphere are 12 cm and 10 cm. Find its volume. -Maths 9th

Last Answer : This answer was deleted by our moderators...

The outer and the inner radii of a hollow sphere are 12 cm and 10 cm. Find its volume. -Maths 9th

Description : The outer and the inner radii of a hollow sphere are 12 cm and 10 cm. Find its volume. -Maths 9th

Last Answer : This answer was deleted by our moderators...

Find the resistance of a hollow cylindrical conductor of length 1.0m and inner and outer radii 1.0mm and 2.0mm respectively. The resistivity of the ma

Description : Find the resistance of a hollow cylindrical conductor of length 1.0m and inner and outer radii 1.0mm and 2.0mm respectively. The resistivity of the ma

Last Answer : Find the resistance of a hollow cylindrical conductor of length 1.0m and inner and outer radii 1.0mm and 2 ... the material is `2.0xx10^(-8)(Omega)m`.

A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Description : A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Last Answer : b) 1.5 kg/cm2

Which stress is constant in a thick shell a) σh b) σl c) σr d) None

Description : Which stress is constant in a thick shell a) σh b) σl c) σr d) None

Last Answer : b) σl

In a thick shell which stress is negligible a) σh b) σl c) σr d) None

Description : In a thick shell which stress is negligible a) σh b) σl c) σr d) None

Last Answer : b) σl

A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing stress of 124 N/mm2. G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Description : A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing ... G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Last Answer : a. 10 turns

Longitudinal stress in a cylinder is given by [symbols have their usual meanings]. a) PD/2t b) 2PD/t c) PD/4t d) 4PD/t

Description : Longitudinal stress in a cylinder is given by [symbols have their usual meanings]. a) PD/2t b) 2PD/t c) PD/4t d) 4PD/t

Last Answer : c) PD/4t

Tangential stress in a cylinder is given by [symbols have their usual meanings]. a) PD/2t b) 2PD/t c) PD/4t d) 4PD/t

Description : Tangential stress in a cylinder is given by [symbols have their usual meanings]. a) PD/2t b) 2PD/t c) PD/4t d) 4PD/t

Last Answer : a) PD/2t

Hoop strain in a thin shell is a) σh /E b) σl /E c) 3 σh /E d) None

Description : Hoop strain in a thin shell is a) σh /E b) σl /E c) 3 σh /E d) None

Last Answer : d) None