The stress in the wall of a cylinder in a direction normal to its longitudinal axis, due to a force
acting along the circumference, is known as
(A) Yield stress
(B) Longitudinal stress
(C) Hoop stress
(D) Circumferential stress
Description : Circumferential welded joint fails by i. Longitudinal stress ii. Radial stress iii. Hoop stress iv. None
Last Answer : i. Longitudinal stress
Description : The ratio of circumferential stress to the longitudinal stress in the walls of a cylindrical shell, due to flowing liquid, is (A) ½ (B) 1 (C) 1½ (D) 2
Last Answer : (D) 2
Description : Pick up the correct statement from the following: (A) Hoop strain of the walls of a cylinder due to liquid is (pd/2tE) (1 - 1/2m) (B) Longitudinal strain in the walls of a cylinder due to liquid is ... change in the cylinder due to liquid is (pd/2tE) (5/2 - 2/m) (D) All the above
Last Answer : (D) All the above
Description : The ratio of the tensile stress developed in the wall of a boiler in the circumferential direction to the tensile stress in the axial direction, is (A) 4 (B) 3 (C) 2 (D) 1
Last Answer : (C) 2
Description : In a thick-cylinder pressurized from inside, the hoop stress is maximum at a) The center of the wall thickness b) the outer radius c) the inner radius d) both the inner and the outer radii
Last Answer : c) the inner radius
Description : A thin cylindrical under internal pressure can fail along the a. Longitudinal joint b. Circumferential joint c. Longitudinal as well as circumferential joint d. None
Last Answer : c. Longitudinal as well as circumferential joint
Description : A beam is said to be of uniform strength, if (A) B.M. is same throughout the beam (B) Shear stress is same throughout the beam (C) Deflection is same throughout the beam (D) Bending stress is same at every section along its longitudinal axis
Last Answer : (D) Bending stress is same at every section along its longitudinal axis
Description : If is the internal pressure in a thin cylinder of diameter and thickness , the developed hoop stress, is (A) pd/2t (B) pd/4t (C) pd/t (D) 2pd/t
Last Answer : (A) pd/2t
Description : A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal
Last Answer : a) Thrust
Description : What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data
Last Answer : c. 8.88 N/mm2
Description : If is the sectional area of a pre-stressed rectangular beam provided with a tendon pre-stressed by a force through its centroidal longitudinal axis, the compressive stress in concrete, is (A) P/A (B) A/P (C) P/2A (D) 2A/P
Last Answer : Answer: Option A
Description : Longitudinal welded joint fails by Longitudinal stress Radial stress Hoop stress None
Last Answer : Hoop stress
Description : Design of a thin shell under pressure is done on the basis of a. Radial stress b. Longitudinal stress c. Hoop stress d. All the three stresses
Last Answer : c. Hoop stress
Description : Which stress is the least in a thin shell a. Longitudinal stress b. Hoop stress c. Radial stress d. None
Last Answer : c. Radial stress
Description : A thick cylinder is subjected to an internal pressure of 60 MPa. If the hoop stress on the outer surface is 150 MPa, then the hoop stress on the internal surface is a) 105 MPa b) 180 MPa c) 210 MPa d) 135 MPa.
Last Answer : c) 210 MPa
Description : If the elevations along a road increase, the slope of the road along the longitudinal direction, is known as (A) Gradient (B) Grade (C) Positive grade (D) Negative grade
Description : The longitudinal shearing stresses acting on the surface between the steel and concrete are called. (a) Bond stress (b) Tensile stresses (c) Compressive stresses (d) None of these
Last Answer : (a) Bond stress
Description : What is the shear stress acting along the neutral axis, over a triangular section? a. 2.66 (S/bh) b. 1.5 (S/bh) c. 0.375 (S/bh) d. None of the above
Last Answer : a. 2.66 (S/bh)
Description : An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm
Description : In a spherical dome the hoop stress due to a concentrated load at crown is (A) Compressive everywhere (B) Tensile everywhere (C) Partly compressive and partly tensile (D) Zero
Last Answer : Answer: Option B
Description : The intensity of direct longitudinal stress in the cross-section at any point distant r from the neutral axis, is proportional to (A) r (B) 1/r (C) r2 (D) 1/r²
Last Answer : (A) r
Description : If the tendon is placed at an eccentricity e below the centroidal axis of the longitudinal axis of a rectangular beam (sectional modulus Z and stressed load P in tendon) the stress at the extreme top edge (A) Is ... by PZ/e (B) Is increased by Pe/Z (C) Is decreased by Pe/Z (D) Remains unchanged
Last Answer : Answer: Option C
Description : In modeling of a tabulated cylinder, the plane of the curve is _______ a.along the curve b.normal to the curve c.along the axis of the cylinder d.perpendicular to the axis of the cylinder
Last Answer : d.perpendicular to the axis of the cylinder
Description : The rise of liquid along the walls of a revolving cylinder about the initial level is __________ the depression of the liquid at the axis of rotation. (A) Same as (B) Less than (C) More than (D) None of these
Description : Longitudinal stress in a cylinder is given by [symbols have their usual meanings]. a) PD/2t b) 2PD/t c) PD/4t d) 4PD/t
Last Answer : c) PD/4t
Description : Steering of a car involves: A. A pair of forces acting along the same line and in opposite direction B. Two forces acting in the same direction C. Two forces acting along different lines and in opposite direction D. A single force
Last Answer : ANSWER: A
Description : Steering of a car involves? A. A single force B. Two forces acting in the same direction C. Two forces acting along different lines and in opposite direction. D. A pair of forces acting along the same line and in opposite direction (Answer)
Last Answer : D. A pair of forces acting along the same line and in opposite direction (Answer)
Description : Due to circumferential action of the spiral in a spirally reinforced column (A) Capacity of column is decreased (B) Ductility of column reduces (C) Capacity of column is decreased but ductility of column increases (D) Both the capacity of column and ductility of column increase
Last Answer : Answer: Option D
Description : Due to Circumferential action of the spiral reinforcement in a column [ A ] Capacity of column is decreased but ductility of column increases [ B ] Both the capacity of column an ductility of column increases [ C ] Capacity of column increases [ D ] Ductility of the column reduces
Last Answer : [ B ] Both the capacity of column an ductility of column increases
Description : The maximum magnitude of shear stress due to shear force F on a rectangular section of area A at the neutral axis, is (A) F/A (B) F/2A (C) 3F/2A (D) 2F/3A
Last Answer : (C) 3F/2A
Description : The pressure acting on the stones in stone masonry construction should be (A) Along the direction of bedding planes (B) At 45° to the direction of bedding planes (C) At 60° to the direction of bedding planes (D) Perpendicular to the direction of bedding planes
Description : Is the plane of cell division in paramecium along the longitudinal axis?
Last Answer : What is the answer ?
Description : If the particle of a body vibrate along a circular arc, whose centre lies on the axis of the shaft then the body is said to have A) Transverse vibration B) Longitudinal vibration C) Torsional vibration D) None of the above
Last Answer : C) Torsional vibration
Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube
Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K
Description : The vertical angle between longitudinal axis of a freely suspended magnetic needle and a horizontal line at its pivot, is known (A) Declination (B) Azimuth (C) Dip (D) Bearing
Last Answer : (C) Dip
Description : The distance travelled by revolving the wheel of a vehicle more than its circumferential movement, is known as (A) Slip (B) Skid (C) Neither (a) nor (b) (D) Both (a) and (b)
Description : The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram
Last Answer : (d) Trust diagram
Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed
Last Answer : a) M/2πtr2
Description : A pressure conduit laid underground, may not be subjected to (A) Internal pressure of water (B) Pressure due to external load (C) Longitudinal temperature stress (D) Longitudinal stresses due to unbalanced pressure to bends
Last Answer : (C) Longitudinal temperature stress
Description : The earth's gravitational force field is said to be conservative force field because a.The work acted by the earth's gravitational field on a particle is independent on the path traced out by ... directional component always acting normal to a body e.The value of gravitational force rise is fixed
Last Answer : a. The work acted by the earth's gravitational field on a particle is independent on the path traced out by the particle
Description : An open-ended cylinder of radius and thickness is subjected to internal pressure . The Young's modulus for the material is and Poisson's ratio is . The longitudinal strain is (A) Zero (B) pr/TE (C) pr/2TE (D) None of these
Last Answer : (A) Zero
Description : two forces acting at a joint are not along the straight line, then for the equilibrium of the joint (A) One of the forces must be zero (B) Each force must be zero (C) Forces must be equal and of the same sign (D) Forces must be equal in magnitude but opposite in sign
Last Answer : (B) Each force must be zero
Description : The shearing force acting along the slice of a curved surface of slippage, causes the soil to slide (A) Down at the centre (B) Down at the toe (C) Upward at the centre (D) None of these
Description : Which of the following statement is false? a.The potential energy of a particle has the form Ep = k2x. The force acting on the particle is constant (k is a constant) b.The linear velocity of ... zag path while ascending a steep hill e.The density of milk decreases when cream is taken out of milk
Last Answer : e. The density of milk decreases when cream is taken out of milk
Description : According to law of triangle of forces (A) Three forces acting at a point will be in equilibrium (B) Three forces acting at a point can be represented by a triangle, each side ... point are in equilibrium, each force is proportional to the sine of the angle between the other two
Last Answer : (C) If three forces acting upon a particle are represented in magnitude and direction by the sides of a triangle, taken in order, they will be in equilibrium
Description : According to Lami's theorem (A) Three forces acting at a point will be in equilibrium (B) Three forces acting at a point can be represented by a triangle, each side being proportional to ... point are in equilibrium, each force is proportional to the sine of the angle between the other two
Description : Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above
Last Answer : b. Soderberg line
Description : In a singly reinforced beam, the effective depth is measured from its compression edge to (A) Tensile edge (B) Tensile reinforcement (C) Neutral axis of the beam (D) Longitudinal central axis
Description : In a solid arch, shear force acts (A) Vertically upwards (B) Along the axis of the arch (C) Perpendicular to the axis of arch (D) Tangentially to the arch
Last Answer : (C) Perpendicular to the axis of arch
Description : The shear stress acting on the neutral axis of a beam is _____ a. maximum b. minimum c. zero d. none of the above
Last Answer : a. maximum