The number of diodes used in bridge rectifier circuit is (a) 4 (b) 3 (c) 2 (d)

The number of diodes used in bridge rectifier circuit is
(a) 4 (b) 3 (c) 2 (d)
by

1 Answer

Answer :

(a) 4
by

Related questions

The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions

Description : The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions

Last Answer : Answer: A

Pure semiconductors silicon and germanium are a) Extrinsic b) Intrinsic c) Insulator d) Diodes

Description : Pure semiconductors silicon and germanium are a) Extrinsic b) Intrinsic c) Insulator d) Diodes

Last Answer : b) Intrinsic

Circuit which gives continuously varying potential is called a. complex network b. wheat stone bridge c. potential divider d. all of above

Description : Circuit which gives continuously varying potential is called a. complex network b. wheat stone bridge c. potential divider d. all of above

Last Answer : c. potential divider

The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Description : The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Last Answer : a) A pulsating uni-directional current

In a half wave rectifier the rms value of AC component of the waves (a) Zero (b) Equal to DC value (c) More than DC value (d) Less than DC value

Description : In a half wave rectifier the rms value of AC component of the waves (a) Zero (b) Equal to DC value (c) More than DC value (d) Less than DC value

Last Answer : b) Equal to DC value

Which is the most important building block of electronic devices? (a) Diode (b) p-n junction (c) transistor (d) rectifier

Description : Which is the most important building block of electronic devices? (a) Diode (b) p-n junction (c) transistor (d) rectifier

Last Answer : b) p-n junction

Heat sinks are frequently used with _____________. A. power transistors B. vacuum tubes C. tunnel rectifier diodes D. all of the above

Description : Heat sinks are frequently used with _____________. A. power transistors B. vacuum tubes C. tunnel rectifier diodes D. all of the above

Last Answer : Answer: A

What are the advantages of freewheeling diodes in a controlled in a controlled rectifier?

Description : What are the advantages of freewheeling diodes in a controlled in a controlled rectifier?

Last Answer : a. Input power factor is improved. b. Load current waveform is improved and thus the load performance is better.

What is the function of freewheeling diodes in controlled rectifier?

Description : What is the function of freewheeling diodes in controlled rectifier?

Last Answer : It serves two process. a. It prevents the output voltage from becoming negative. b. The load current is transferred from the main thyristors to the freewheeling diode, thereby allowing all of its thyristors to regain their blocking states.

Current limited power supplies can prevent damage to A) Rectifier diodes and power transformers. B) Pass transistors C) Other circuits in the system D) All of the above.

Description : Current limited power supplies can prevent damage to A) Rectifier diodes and power transformers. B) Pass transistors C) Other circuits in the system D) All of the above.

Last Answer : D) All of the above.

Which rectifier requires four diodes

Last Answer : Bridge rectifier requires four diodes 

Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms.

Description : Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms. 

Last Answer : During the first half cycle : During the first half cycle of the input voltage, the upper end of the transformer secondary winding is positive with respect to the lower end. Thus during the first ... , terminal D, diode D4, and terminal A back to transformer and output will positive half cycle.

Draw the circuit diagram of bridge rectifier and label it.

Description : Draw the circuit diagram of bridge rectifier and label it. 

Last Answer : Circuit Diagram Bridge rectifier

Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier

Description : Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier 

Last Answer : Rectifier - This circuit convert AC signal into DC.

Draw the circuit diagram of bridge rectifier with π filter. Draw its input and output waveform.

Description : Draw the circuit diagram of bridge rectifier with π filter. Draw its input and output waveform. 

Last Answer : Circuit diagram of bridge rectifier with π filter : Input and output waveform:

Sketch circuit diagram of bridge rectifier with LC filter. State function of each component.

Description : Sketch circuit diagram of bridge rectifier with LC filter. State function of each component.

Last Answer :  Circuit diagram :  Components and its function: :  1. Transformer- An electrical device which transfers electrical energy from one electric circuit to other, without changing the frequency. The ... DC components.  4. Capacitor- It bypasses AC components if any and gives DC to load. 

circuit I mean What ?

Last Answer : electricity Source , conductor , control Instruments , Usage Machines , Protection Machines In combination Such A Path Whose The middle With Current Flowing To be Can Him Circuit Or Circuit Says.

A 0-10 mA PMMC ammeter reads 5mA in a circuit; its bottom control spring snaps out suddenly the meter will now read. a) 5mA b) 10mA c) 2.5mA d) 0

Description : A 0-10 mA PMMC ammeter reads 5mA in a circuit; its bottom control spring snaps out suddenly the meter will now read. a) 5mA b) 10mA c) 2.5mA d) 0

Last Answer : Ans: 0

indicate the false statement.TheSWRon a transmissionline isinfinity;the line isterminated in a. a short circuit b. acompleximpedance c. an open circuit d. a pure reactance

Description : indicate the false statement.TheSWRon a transmissionline isinfinity;the line isterminated in a. a short circuit b. acompleximpedance c. an open circuit d. a pure reactance

Last Answer : b. acompleximpedance

After a black out the emergency generator comes on; On restoring the main supply we are closing the circuit breaker of the main generator without bothering about synchronizing. How is this possible?

Description : After a black out the emergency generator comes on; On restoring the main supply we are closing the circuit breaker of the main generator without bothering about synchronizing. How is this possible?

Last Answer : There is a power link connection breaker between the main generator and the emergency generator. During black out, this breaker trips. The emergency generator starts and its breaker closes and feeds only ... , there is no paralleling between main and emergency generator. Ask E/O for more details.

What is a self-monitoring alarm circuit?

Description : What is a self-monitoring alarm circuit?

Last Answer : It self monitors the health of the alarm circuit. That is, it senses whether the power supply to the alarm circuit is healthy and all the relays and contacts are functioning normally. Check with E/O for more details.

What is meaning of short circuit?

Description : What is meaning of short circuit?

Last Answer : A short circuit occurs when conductors are connected (shorted) together by a fault. This is normally phase to phase fault due to failure of insulation by something cutting the wires, fires, etc.

Can you draw a DOL starter circuit?

Description : Can you draw a DOL starter circuit?

Last Answer : Refer to DOL diagram in Dennis T Hall

The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Description : The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Last Answer : (d) inverter

Forward current through a semi-conductor diode circuit is due to ________ (a) Minority carriers (b) majority carriers (c) holes (d) electrons

Description : Forward current through a semi-conductor diode circuit is due to ________ (a) Minority carriers (b) majority carriers (c) holes (d) electrons

Last Answer : (b) majority carriers

The induced emf is produced in a circuit due to: a. Initial magnetic flux b. final magnetic flux c. Change of magnetic flux d. constant magnetic flux

Description : The induced emf is produced in a circuit due to: a. Initial magnetic flux b. final magnetic flux c. Change of magnetic flux d. constant magnetic flux

Last Answer : d. constant magnetic flux

A circuit which develops voltage across the horizontal deflection plates is known as a) Time base generator b) Electron gun c) Thermionic diode d) Zener diode

Description : A circuit which develops voltage across the horizontal deflection plates is known as a) Time base generator b) Electron gun c) Thermionic diode d) Zener diode

Last Answer : a) Time base generator

Why should a resistance be introduced in a circuit in series deliberately? a. to increase current b. to decrease current c. to control current d. just to give a good look to circuit

Description : Why should a resistance be introduced in a circuit in series deliberately? a. to increase current b. to decrease current c. to control current d. just to give a good look to circuit

Last Answer : b. to decrease current

Resistance between points A and B in the circuit shown in figure is a. 4 ohm b. 6ohm c. 10 ohm d. 8 ohm

Description : Resistance between points A and B in the circuit shown in figure is a. 4 ohm b. 6ohm c. 10 ohm d. 8 ohm

Last Answer : c. 10 ohm

The current in the circuit shown in figure - What will be the current in the circuit? a. 1/45A b. 1/10A c. 1/5A d. 5A

Description : The current in the circuit shown in figure - What will be the current in the circuit? a. 1/45A b. 1/10A c. 1/5A d. 5A

Last Answer : b. 1/10A

Refer to the circuit below . The power consumed by the element E is equal

Description : الرجوع إلى الدائرة أدناه. الطاقة التي يستهلكها العنصر E متساوية.

Last Answer : The power consumed the element E is equal to the  : P = V x I = 6V x 1 A = 6 W

Refer to the circuit below. The voltage V2, is equal to:

Description : Refer to the circuit below. The voltage V2, is equal to:

Last Answer : The answer to this question is -3V. Because 3V is in parallel with v2 and voltages in parallel are equal. But it is in opposite direction so the answer is -3V.

Briefly explain how the power factor of an inductive circuit can be improved.

Description : Briefly explain how the power factor of an inductive circuit can be improved.

Last Answer : As we know that power factor should be corrected to ensure that the current supplied is cost friendly. Meaning the power factor should be around one but not greater than one(0.8-0.9) in a ... an inductive circuit due to the inductive reactance which oppose the change of current in the ac circuit. 

What is electrical circuit ?

Description : What is electrical circuit ?

Last Answer : An electric circuit is the interconnection of electrical elements. Electrical elements like battery, lamp, wire etc.

A circuit breaker is designed to protect an electrical circuit from damage caused by :

Description : A circuit breaker is designed to protect an electrical circuit from damage caused by :  (A) Over load (B) Short circuit (C) Over current (D) All of the above

Last Answer : A circuit breaker is designed to protect an electrical circuit from damage caused by :  (A) Over load (B) Short circuit (C) Over current (D) All of the above

An electrical circuit with 10 branches and 7 junctions will have

Description : An electrical circuit with 10 branches and 7 junctions will have

Last Answer : An electrical circuit with 10 branches and 7 junctions will have  4 loop equations.

The resistance of a few meters of wire conductor in closed electrical circuit is?

Description : The resistance of a few meters of wire conductor in closed electrical circuit is?

Last Answer : The resistance of a few meters of wire conductor in closed electrical circuit is practically zero.

Power factor of an electrical circuit is equal to?

Description : Power factor of an electrical circuit is equal to?

Last Answer : Power factor of an electrical circuit is equal to R/Z, cosine of phase angle difference between current and voltage, kW/kVA.

What is a node in an electrical circuit?

Description : What is a node in an electrical circuit?

Last Answer : a positively charged electrons

In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC

Description : In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC

Last Answer : Answer: D

Draw the circuit diagram for AND and OR gates using diodes.

Description : Draw the circuit diagram for AND and OR gates using diodes.

Last Answer : Diode AND gate :Diode OR gate : 

A voltage signal 10 Sinwt is applied to the circuit with ideal diodes, as shown in figure. The maximum and

Description : A voltage signal 10 Sinwt is applied to the circuit with ideal diodes, as shown in figure. The maximum and minimum values of the output waveform vout of the circuit are respectively

Last Answer : A voltage signal 10 Sinwt is applied to the circuit with ideal diodes, as shown in figure. The maximum and minimum values of the output waveform vout of the circuit are respectively +4V and-7V

The circuit has resistors, capacitors and semi-conductor diodes. The circuit will be known as?

Description : The circuit has resistors, capacitors and semi-conductor diodes. The circuit will be known as

Last Answer : The circuit has resistors, capacitors and semi-conductor diodes. The circuit will be known as non-linear circuit.

The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Description : The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Last Answer : Answer: A

What does the arrangement at coordinates '62E' shown in the illustration represent? EL-0099 A. Position recording drum and stylus B. Temperature compensating thyristor C. Miniature bridge rectifier D. Twisted wire pair within a shield

Description : What does the arrangement at coordinates '62E' shown in the illustration represent? EL-0099 A. Position recording drum and stylus B. Temperature compensating thyristor C. Miniature bridge rectifier D. Twisted wire pair within a shield

Last Answer : Answer: D

The schematic diagram shown in the illustration represents which of the listed solid-state circuits? EL-0069 A. Bridge rectifier B. Magnetic amplifier C. Flip-flop generator D. Cathodic amplifier

Description : The schematic diagram shown in the illustration represents which of the listed solid-state circuits? EL-0069 A. Bridge rectifier B. Magnetic amplifier C. Flip-flop generator D. Cathodic amplifier

Last Answer : Answer: A

Component 'B' of section 'I' shown in the illustration represents a _____________. EL-0093 A. bridge rectifier B. selsyn motor C. small generator D. shielded lamp

Description : Component 'B' of section 'I' shown in the illustration represents a _____________. EL-0093 A. bridge rectifier B. selsyn motor C. small generator D. shielded lamp

Last Answer : Answer: C

Full wave bridge rectifier?

Description : Full wave bridge rectifier?

Last Answer : Full wave bridge rectifier: In full wave bridge rectifiers 4 diodes are using. During positive half cycle, D1 and D4 are in forward biased condition. In the negative half cycle of ac D3 and D2 ... a centre tap rectifier. But it requires more number of diodes than centre tap and half wave rectifiers

Why we are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?

Description : Why we are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?

Last Answer : Ans-In bridge type (FWR) rectifiers center tapping transformer are not required so small transformers are used and we will get twice of the out put voltage that of the center tapped FWR.

What main advantage does a bridge rectifier have over a conventional full-wave rectifier?

Description : What main advantage does a bridge rectifier have over a conventional full-wave rectifier?

Last Answer : The bridge rectifier can produce twice the voltage with the same size transformer.