Etching a hybrid glass ionomer-composite a. is necessary for composite resin bonding b. is not necessary for composite resin bonding c. is necessary for adding a glass ionomer cement for repair d. is not necessary for adding a glass ionomer cement for repair e. a 3-5 second etch with 10% phosphoric acid is recommended

Etching a hybrid glass ionomer-composite
a. is necessary for composite resin bonding  
b. is not necessary for composite resin bonding  
c. is necessary for adding a glass ionomer cement for repair  
d. is not necessary for adding a glass ionomer cement for repair  
e. a 3-5 second etch with 10% phosphoric acid is recommended
by

1 Answer

Answer :

b. is not necessary for composite resin bonding
by

Related questions

The effectiveness of the acid etch is dependent on which of the following factors: A. Material must be used to clean the surface of the tooth prior to etching B. The effectiveness of the itchant C. The chemical and physical nature of the tooth D. The area and surface of the enamel to be itched

Description : The effectiveness of the acid etch is dependent on which of the following factors: A. Material must be used to clean the surface of the tooth prior to etching B. The effectiveness of the itchant C. The chemical and physical nature of the tooth D. The area and surface of the enamel to be itched

Last Answer : C. The chemical and physical nature of the tooth

lass Ionomer Cement sets because of,** A. Acid-Base reaction B. Addition polymerisation reaction C. Growth of glass crystals D. Slip plane locking E. Solvent evaporation

Description : lass Ionomer Cement sets because of,** A. Acid-Base reaction B. Addition polymerisation reaction C. Growth of glass crystals D. Slip plane locking E. Solvent evaporation

Last Answer : A. Acid-Base reaction

Pin Restoration with which material has the best retention: A. Amalgam B. Gold inlay C. Composite D. Glass Ionomer

Description : Pin Restoration with which material has the best retention:  A. Amalgam  B. Gold inlay  C. Composite  D. Glass Ionomer 

Last Answer : C. Composite 

A patient comes to you with medium pain of tooth filled with Composite resin as a result of cold or hot drinks, what will your initial management be, A. Remove the restorative material and start an Endontic treatment B. Remove the restorative material and place a sedative temporary material C. Place a coat of bonding material on the old composite

Description : A patient comes to you with medium pain of tooth filled with Composite resin as a result of cold or hot drinks, what will your initial management be, A. Remove the restorative material and ... material and place a sedative temporary material C. Place a coat of bonding material on the old composite

Last Answer : B. Remove the restorative material and place a sedative temporary material

Which of the following is NOT a characteristic of glass ionomer cements? a. strong in compression but weaker in tension True b. the matrix is formed during the initial set of the cement c. sets via an ion exchange reaction that continues for at least 24 hours true d. suitable for use as a core build up material in anterior teeth

Description : Which of the following is NOT a characteristic of glass ionomer cements? a. strong in compression but weaker in tension True b. the matrix is formed during the initial set of the cement c. sets via ... for at least 24 hours true d. suitable for use as a core build up material in anterior teeth

Last Answer : d. suitable for use as a core build up material in anterior teeth

With dentin bonding agent, you apply: A. First acid etching to dentine and then bonding agent B. Bonding agent directly to dentine C. Chelating agent (EDTA) and bonding agent

Description : With dentin bonding agent, you apply: A. First acid etching to dentine and then bonding agent B. Bonding agent directly to dentine C. Chelating agent (EDTA) and bonding agent

Last Answer : A. First acid etching to dentine and then bonding agent

In 3rd generation dentin bonding agents, HEMA (Hydroxyethylmethacrylate) is 1. a hydrophilic monomer that wets the dentinal surface 2. a hydrophilic resin that forms a ”hybrid” layer by chemically reacting the intertubular dentin. 3. a hydrophilic monomer that alters collagen to promote cross linking of collagen to dentin. 4. a bifunctional molecule resin that copolymerizes to bis-GMA resins. a. 1,2 b. 1,4 c. 2,3 d. 1,3 e. 3,4

Description : In 3rd generation dentin bonding agents, HEMA (Hydroxyethylmethacrylate) is 1. a hydrophilic monomer that wets the dentinal surface 2. a hydrophilic resin that forms a hybrid layer by chemically reacting the intertubular dentin. 3. a hydrophilic ... a. 1,2 b. 1,4 c. 2,3 d. 1,3 e. 3,4

Last Answer : b. 1,4

What stencils do I use to etch glass mugs with Etching Cream?

Description : What stencils do I use to etch glass mugs with Etching Cream?

Last Answer : Need Answer

Which material is not compatible with composite resin: A. Zinc Oxide eugenol (ZOE) B. Ca(OH)2 C. Carboxylate D. Zinc phosphate cement

Description : Which material is not compatible with composite resin: A. Zinc Oxide eugenol (ZOE) B. Ca(OH)2 C. Carboxylate D. Zinc phosphate cement

Last Answer : A. Zinc Oxide eugenol (ZOE)

The clinical advantage of porcelain laminate veneers over composite resin veneers is: A. Color stability and resistance to abrasion B. Availability of self-curing or light activated placement (yes but not necessary a clinical advantage) C. Minimal over-contouring of the treated teeth ( not necessarily true depends on the dentist's abilities) D. May be used in edge to edge occlusion or Class III relationships.

Description : The clinical advantage of porcelain laminate veneers over composite resin veneers is: A. Color stability and resistance to abrasion B. Availability of self-curing or light activated placement (yes but not ... dentist's abilities) D. May be used in edge to edge occlusion or Class III relationships.

Last Answer : A. Color stability and resistance to abrasion

On examination of a composite restoration you find a dark attain: A. Replace the composite B. Repair with unfilled resin C. Apply topical fluoride at the margin

Description : On examination of a composite restoration you find a dark attain: A. Replace the composite B. Repair with unfilled resin C. Apply topical fluoride at the margin

Last Answer : A. Replace the composite

.What is the percentage of the echant agent used with composit resin restorations? a . 37% of phosphoric acid in water. b. 15% c. 18.5% d. 41%

Description : .What is the percentage of the echant agent used with composit resin restorations? a . 37% of phosphoric acid in water. b. 15% c. 18.5% d. 41%

Last Answer : a . 37% of phosphoric acid in water.

When incrementally placing a large composite resin restoration, what effect does an air-inhibited layer on the surface of the first increment have on the bond between the first and the second increments? A. It has no effect on the bond B. It is desirable and improves the bond C. It is undesirable and should be removed

Description : When incrementally placing a large composite resin restoration, what effect does an air-inhibited layer on the surface of the first increment have on the bond between the first and the second increments? A. ... B. It is desirable and improves the bond C. It is undesirable and should be removed

Last Answer : B. It is desirable and improves the bond

What is the active agent in most home (night guard) bleaching solutions? a. 2-5% carbamide peroxide b. 10 - 15% Phosphoric acid c. 10 - 15% carbamide peroxide d. 35% hydrogen peroxide e. 5 - 10% citric acid Attention:

Description : What is the active agent in most home (night guard) bleaching solutions? a. 2-5% carbamide peroxide b. 10 - 15% Phosphoric acid c. 10 - 15% carbamide peroxide d. 35% hydrogen peroxide e. 5 - 10% citric acid Attention:

Last Answer : c. 10 - 15% carbamide peroxide

The best way to clean a cavity before the placement of GIC is,** A. H2O2 B. Phosphoric Acid C. Polyacrylic acid 10% sturdavent 563pag

Description : The best way to clean a cavity before the placement of GIC is,** A. H2O2 B. Phosphoric Acid C. Polyacrylic acid 10% sturdavent 563pag

Last Answer : C. Polyacrylic acid 10% sturdavent 563pag

Class V composite resin restorations can be polished, A. 24 hours after application B. Immediately after application C. 3 to 4 days D. 3 to 4 weeks E. Not at all

Description : Class V composite resin restorations can be polished, A. 24 hours after application B. Immediately after application C. 3 to 4 days D. 3 to 4 weeks E. Not at all

Last Answer : B. Immediately after application

Why do you itch enamel for composite restorations: A. To increase surface area B. To decrease surface area C. Does not really change the surface area D. Increase the chemical bonding capability E. Decrease the chemical bonding capability

Description : Why do you itch enamel for composite restorations: A. To increase surface area B. To decrease surface area C. Does not really change the surface area D. Increase the chemical bonding capability E. Decrease the chemical bonding capability

Last Answer : A. To increase surface area

In a posterior vital molar with a core the best material to restore is: A. Amalgam B. Composite resin C. GIC

Description : In a posterior vital molar with a core the best material to restore is: A. Amalgam B. Composite resin C. GIC

Last Answer : A. Amalgam

Sensitivity to hot and cold foods soon after cavity preparation and placement of GIC and composite resin in an upper incisor tooth is due to: A. Mechanical trauma due to cavity preparation B. Chemical C. Heat from GIC settings

Description : Sensitivity to hot and cold foods soon after cavity preparation and placement of GIC and composite resin in an upper incisor tooth is due to: A. Mechanical trauma due to cavity preparation B. Chemical C. Heat from GIC settings

Last Answer : A. Mechanical trauma due to cavity preparation

A seven years-old boy fell off his bicycle 2 weeks ago and broke his maxillary central incisor. The pulp horn is visible as a pin point. The tooth is vital. Your treatment will be: A. Pulpectomy B. Place calcium hydroxide and fill with composite resin C. Calcium hydroxide pulpotomy

Description : A seven years-old boy fell off his bicycle 2 weeks ago and broke his maxillary central incisor. The pulp horn is visible as a pin point. The tooth is vital. Your treatment will be: A. Pulpectomy B. Place calcium hydroxide and fill with composite resin C. Calcium hydroxide pulpotomy

Last Answer : C. Calcium hydroxide pulpotomy

Which of the following restoration material’s strength is not effected by pins: A. Amalgam B. Composite resin

Description : Which of the following restoration material’s strength is not effected by pins: A. Amalgam B. Composite resin

Last Answer : B. Composite resin

What is the advantage of composite over silicate resin: A. Less shrinkage B. Less surface erosion C. Less water absorption D. All of the above

Description : What is the advantage of composite over silicate resin: A. Less shrinkage B. Less surface erosion C. Less water absorption D. All of the above

Last Answer : D. All of the above

When do you finish composite resin restorations: A. Immediately after curing B. After 24 hours C. A week after placement

Description : When do you finish composite resin restorations: A. Immediately after curing B. After 24 hours C. A week after placement

Last Answer : A. Immediately after curing

A patient has a small incisal fracture of the maxillary incisor. Which is the best material to resist fracture at the acid etched tooth composite interface: A. Micro-filled composite B. Hybrid composite C. GIC D. Silicate

Description : A patient has a small incisal fracture of the maxillary incisor. Which is the best material to resist fracture at the acid etched tooth composite interface: A. Micro-filled composite B. Hybrid composite C. GIC D. Silicate

Last Answer : B. Hybrid composite

How can you improve the adhesion of a fissure sealant: A. Acid etching technique

Description : How can you improve the adhesion of a fissure sealant: A. Acid etching technique

Last Answer : A. Acid etching technique

The un-polymerized monomer in Self-cured resin is approximately:** A. 0.5% B. 2.5% C. 5% D. 10%

Description : The un-polymerized monomer in Self-cured resin is approximately:** A. 0.5% B. 2.5% C. 5% D. 10%

Last Answer : C. 5%

What is the best way to cement Maryland bridge, A. GIC B. Resin C. High compression restorative resin D. Zinc Phosphate cement E. Oxide Zinc and eugenol

Description : What is the best way to cement Maryland bridge, A. GIC B. Resin C. High compression restorative resin D. Zinc Phosphate cement E. Oxide Zinc and eugenol

Last Answer : B. Resin

Etching techniques are used always to: A. minimise the leakage of restorations B. for aesthetic considerations

Description : Etching techniques are used always to: A. minimise the leakage of restorations B. for aesthetic considerations

Last Answer : A. minimise the leakage of restorations

.In regard to the glass of quartz particles of filling restorative resin; the microfill resins tend to have, A. A higher coefficient of thermal expansion and a higher crashing strength B. A higher coefficient of thermal expansion and a lower crashing strength C. A lower coefficient of thermal expansion and a higher crashing strength D. A lower coefficient of thermal expansion and a lower crashing strength

Description : .In regard to the glass of quartz particles of filling restorative resin; the microfill resins tend to have, A. A higher coefficient of thermal expansion and a higher crashing strength B. ... and a higher crashing strength D. A lower coefficient of thermal expansion and a lower crashing strength

Last Answer : B. A higher coefficient of thermal expansion and a lower crashing strength

Several applications have been suggested to increase the effectiveness of prophylactic application of topical fluoride which include all EXCEPT: A. Increase Fluoride ions in solution “increase concentration” B. Increase PH of fluoride C. Increase exposure time to topical fluoride D. Pre-treat enamel with 0.5% phosphoric acid E. Use NH4F instead of NaF

Description : Several applications have been suggested to increase the effectiveness of prophylactic application of topical fluoride which include all EXCEPT: A. Increase Fluoride ions in solution increase concentration B. Increase ... D. Pre-treat enamel with 0.5% phosphoric acid E. Use NH4F instead of NaF

Last Answer : B. Increase PH of fluoride

Several approaches have been suggested to increase the fixation of professionally applied topical fluoride, which of the following statements IS INCORRECT regarding increasing the fixation? A. Increase concentration of fluoride in solutions B. Raise the PH of the fluoride solution C. Increase the exposure time to topical fluoride D. Pre-treat the enamel with 0.5% phosphoric acid E. Use NH4F rather than NaF at a lower PH

Description : Several approaches have been suggested to increase the fixation of professionally applied topical fluoride, which of the following statements IS INCORRECT regarding increasing the fixation? A. Increase concentration of ... with 0.5% phosphoric acid E. Use NH4F rather than NaF at a lower PH

Last Answer : B. Raise the PH of the fluoride solution

Acid conditioning of enamel and eroded dentine: A. Provides an none traumatic, conservative clinical approach to the bonding of restorative material B. Is a traumatic approach to bonding materials C. Is not a safe and simple method of bonding D. Bonding fails to produce a highly significant retention and good marginal integrity and clinical durability E. None of the above

Description : Acid conditioning of enamel and eroded dentine: A. Provides an none traumatic, conservative clinical approach to the bonding of restorative material B. Is a traumatic approach to bonding ... highly significant retention and good marginal integrity and clinical durability E. None of the above

Last Answer : A. Provides an none traumatic, conservative clinical approach to the bonding of restorative material

Is hydrofluoric acid attacking glass and etching designs in glass a physical change?

Description : Is hydrofluoric acid attacking glass and etching designs in glass a physical change?

Last Answer : No, it is a chemical change. The glass is changed into newsubstances where it is etched.

When preparing a class III cavity for composite restoration; in which situation should acid itching be used: A. Always should be performed to minimise marginal leakage B. Should not be performed because it might damage the adjacent tooth C. When extra retention is required D. Only in situations where cavity is shallow to avoid pulp irritation

Description : When preparing a class III cavity for composite restoration; in which situation should acid itching be used: A. Always should be performed to minimise marginal leakage B. Should not be ... extra retention is required D. Only in situations where cavity is shallow to avoid pulp irritation

Last Answer : A. Always should be performed to minimise marginal leakage

Pick up the correct statement from the following: (A) Cement should be mixed for at least one minute (B) 10% of water is placed in the rotating drum before adding dry material (C) 10% of water is added after placing the other ingredients in the drum (D) All the above

Description : Pick up the correct statement from the following: (A) Cement should be mixed for at least one minute (B) 10% of water is placed in the rotating drum before adding dry material (C) 10% of water is added after placing the other ingredients in the drum (D) All the above

Last Answer : Answer: Option D

How to Etch Glass

Description : How to Etch Glass

Last Answer : How to Etch Glass Etching glass is a great way to personalize items like glasses, vases, glass awards and other similar objects. Personalized glass can be made into giveaways, souvenirs, or a fun ... , rinsing the glass under running water again. Let dry. You know have yourself an etched glass.

In regard to the enamel surface: A. It is a perfect substance for bonding B. It does not conform to the bonding requirements C. It is the most inorganic, rough part D. It is free from contamination and roughness E. None of the above

Description : In regard to the enamel surface: A. It is a perfect substance for bonding B. It does not conform to the bonding requirements C. It is the most inorganic, rough part D. It is free from contamination and roughness E. None of the above

Last Answer : B. It does not conform to the bonding requirements

Platinum and silver are corroded by (A) Caustic soda solution (B) Phosphoric acid (C) Sulphuric acid (10%) (D) None of these

Description : Platinum and silver are corroded by (A) Caustic soda solution (B) Phosphoric acid (C) Sulphuric acid (10%) (D) None of these

Last Answer : (D) None of these

Which can do glass etching?

Description : Which can do glass etching?

Last Answer : Which can do glass etching? A. A) `HlO_4 ` B. (B) HF C. (C) `HNO_3` D. (D) `SiF_4`

How To Make A Glass Etching

Description : How To Make A Glass Etching

Last Answer : When you walk through the halls of a furniture store, you will see a mirror that seems to hold a painting inside. When you approach the mirror, you will realize that the image is painted on the ... room with their classic beauty. Unveil yours to your friends and hear them give silent oohs and ahs.

When considering visible light cured composites, which of the following statements is incorrect? A. An air-inhibited layer is present superficially on the composite. B. The wavelength of the light which affects the initiator is in the range of 450 to 500 nanometers. C. All other things equal. The light generally penetrates deeper into a small-particle composite than it does into a microfilled composite. (smaller particles absorb more light) D. B and C E. All are true

Description : When considering visible light cured composites, which of the following statements is incorrect? A. An air-inhibited layer is present superficially on the composite. B. The wavelength of the light which affects ... composite. (smaller particles absorb more light) D. B and C E. All are true

Last Answer : E. All are true

.In which class of cavities do composite restorations show most durability: A. I B. II C. IV D. III E. V

Description : .In which class of cavities do composite restorations show most durability: A. I B. II C. IV D. III E. V

Last Answer : D. III

A major difference between light cured and chemical cured composite is that during setting or in function the light cured material tends to:******** VERY IMP A. Seal the margins better and completely B. Exhibit less wear on time C. Undergo greater colour change D. Shrink more rapidly E. Posses greater fracture toughness

Description : A major difference between light cured and chemical cured composite is that during setting or in function the light cured material tends to:******** VERY IMP A. Seal the margins better and ... on time C. Undergo greater colour change D. Shrink more rapidly E. Posses greater fracture toughness

Last Answer : D. Shrink more rapidly

Where can we see long lasting composit resin? a. Class III. b. Class II c. ClassV

Description : Where can we see long lasting composit resin? a. Class III. b. Class II c. ClassV

Last Answer : a. Class III.

The effect of the temperature rising above 100ºC on heat-cured denture-base acrylic resins is: A. Produces porosity on the external portion of the resin. B. Produces porosity on the internal portion of the resin. C. Produces porosity on the surface of the resin. D. Prevents porosity on the interior of the resin

Description : The effect of the temperature rising above 100ºC on heat-cured denture-base acrylic resins is: A. Produces porosity on the external portion of the resin. B. Produces porosity on the internal portion ... porosity on the surface of the resin. D. Prevents porosity on the interior of the resin

Last Answer : B. Produces porosity on the internal portion of the resin.

Longest lasting resin restorations are, A. Class I B. Class II C. Class III D. Class IV

Description : Longest lasting resin restorations are,  A. Class I   B. Class II  C. Class III  D. Class IV 

Last Answer : C. Class III 

Where do Maryland bridges lose retention often: A. Resin-metal B. Resin enamel C. Resin layer

Description : Where do Maryland bridges lose retention often: A. Resin-metal B. Resin enamel C. Resin layer

Last Answer : A. Resin-metal

Patient with class II division II; the lateral incisor is missing. You want to make a fixed bridge which of the following is suitable: A. Rocket bridge using central incisor as abutment (rochette bridge resin retained bridge parecido al Maryland B. Cantilever using central incisor C. Fixed bridge using the central incisor and bicuspid

Description : Patient with class II division II; the lateral incisor is missing. You want to make a fixed bridge which of the following is suitable: A. Rocket bridge using central incisor as abutment ( ... al Maryland B. Cantilever using central incisor C. Fixed bridge using the central incisor and bicuspid

Last Answer : B. Cantilever using central incisor

Patient has hot and cold sensation and pain on percussion after the filling of class III Cavity with GIC base and composite. What will be possible cause – 1) bacterial microleakage 2) mechanical trauma of cavity cutting 3) Exothermic reaction while setting GIC

Description : Patient has hot and cold sensation and pain on percussion after the filling of class III Cavity with GIC base and composite. What will be possible cause – 1) bacterial microleakage 2) mechanical trauma of cavity cutting 3) Exothermic reaction while setting GIC

Last Answer : 2) mechanical trauma of cavity cutting

Which one of this restorative methods will be LEAST compromised by a core, A. Amalgam B. Composite C. GIC D. Cast gold

Description : Which one of this restorative methods will be LEAST compromised by a core, A. Amalgam B. Composite C. GIC D. Cast gold

Last Answer : D. Cast gold