Electrical jellies! Got a circuit breaker (home) that has popped and won't reset. Suggestions?

Electrical jellies! Got a circuit breaker (home) that has popped and won't reset. Suggestions?
by

1 Answer

Answer :

My husband, who was a master electrician, said you need to call a professional. You either have a bad breaker or the breaker that refuses to reset is saving your life because you have a dead short some place and your house would burn down if ithe breaker wasn’t tripped.
by

Related questions

My (soon-to-be-replaced) air conditioner is frequently tripping the circuit breaker in my apartment. What can I do to prevent this?

Description : My (soon-to-be-replaced) air conditioner is frequently tripping the circuit breaker in my apartment. What can I do to prevent this?

Last Answer : answer:A mini-split AC unit will use less power than a regular square version and should help with the problem. However if your problem resides in old wiring with a lower amperage/threshold you might ... every time you want to use it but this has cut my electric bill dramatically. Hope this helps

The garage door won't open, any suggestions?

Description : The garage door won't open, any suggestions?

Last Answer : A similar situation happened to me this week. I finally realized that the wall-mounted garage door opener has a lock button on it. I must have accidentally pressed it when opening the door to take the bin out. It then made sense why neither of the remotes didn’t work.

The garage door won't open, any suggestions?

Description : The garage door won't open, any suggestions?

Last Answer : A similar situation happened to me this week. I finally realized that the wall-mounted garage door opener has a lock button on it. I must have accidentally pressed it when opening the door to take the bin out. It then made sense why neither of the remotes didn’t work.

Any suggestions for a phone that won't vibrate?

Description : Any suggestions for a phone that won't vibrate?

Last Answer : Good luck, have the same phone 2 years old and vibrate mode works just fine. Must be a short in the wiring somewhere.

How to reset iTouch?

Description : How to reset iTouch?

Last Answer : Press and hold the power and home button until it shuts off, then release the power but keep holding the home until the connect to itunes screen shows up.

How over voltage is produced in Field breaker?

Description : How over voltage is produced in Field breaker?

Last Answer : Over voltages appear if synchronous generators and motors fall out of step inducing an AC voltage in the field system. Depending on the type of construction of the machine and the slip this ... -permissibly high, for this purpose over voltage protectors are provided in the field breaker cubicle.  

How will a molded-case circuit breaker react after it has tripped, as a result of an overloaded circuit? A. The breaker will trip again if immediately reset. B. The breaker handle will lock in the OFF position. C. The breaker handle will lock in the tripped position until the thermal element cools down. D. The breaker handle cannot be moved to the OFF position until the thermal element cools down.

Description : How will a molded-case circuit breaker react after it has tripped, as a result of an overloaded circuit? A. The breaker will trip again if immediately reset. B. The breaker handle will lock in ... down. D. The breaker handle cannot be moved to the OFF position until the thermal element cools down.

Last Answer : Answer: A

When the operating handle of a molded case circuit breaker is in the mid-position, it indicates the circuit breaker is _____________. A. in the 'opened' position B. in the 'closed' position C. tripped D. reset

Description : When the operating handle of a molded case circuit breaker is in the mid-position, it indicates the circuit breaker is _____________. A. in the 'opened' position B. in the 'closed' position C. tripped D. reset

Last Answer : Answer: C

You are attempting to parallel two AC generators and the synchroscope pointer stops at a position other than 0° prior to closing the circuit breaker. This indicates ___________. A. the frequency of the incoming machine is the same as the bus frequency B. the incoming machine is in phase with the bus, but the frequency is not the same C. the circuit breaker may be closed after breaker has been reset D. there is an existing cross current between generators

Description : You are attempting to parallel two AC generators and the synchroscope pointer stops at a position other than 0° prior to closing the circuit breaker. This indicates ___________. A. the frequency of ... be closed after breaker has been reset D. there is an existing cross current between generators

Last Answer : Answer: A

When the operating handle of a molded-case circuit breaker is in the mid-position, the circuit breaker is indicated as being ____________. A. in the 'closed' position B. in the 'opened' position C. tripped D. reset

Description : When the operating handle of a molded-case circuit breaker is in the mid-position, the circuit breaker is indicated as being ____________. A. in the 'closed' position B. in the 'opened' position C. tripped D. reset

Last Answer : Answer: C

When the operating handle of a molded-case circuit breaker is in the mid-position, this indicates that the circuit breaker is _____________. A. on B. off C. reset D. tripped

Description : When the operating handle of a molded-case circuit breaker is in the mid-position, this indicates that the circuit breaker is _____________. A. on B. off C. reset D. tripped

Last Answer : Answer: D

A circuit breaker differs from a fuse in that a circuit breaker _____________. A. melts and must be replaced B. is enclosed in a tube of insulating material with metal ferrules at each end C. gives no visual indication of having opened the circuit D. trips to break the circuit and may be reset

Description : A circuit breaker differs from a fuse in that a circuit breaker _____________. A. melts and must be replaced B. is enclosed in a tube of insulating material with metal ferrules at each end C. gives no visual indication of having opened the circuit D. trips to break the circuit and may be reset

Last Answer : Answer: D

A circuit breaker and a fuse have a basic similarity in that they both _____________. A. can be reset to energize the circuit B. should open the circuit when overloaded C. will burn out when an over current flow develops D. all of the above

Description : A circuit breaker and a fuse have a basic similarity in that they both _____________. A. can be reset to energize the circuit B. should open the circuit when overloaded C. will burn out when an over current flow develops D. all of the above

Last Answer : Answer: B

How to Reset a Circuit Breaker

Description : How to Reset a Circuit Breaker

Last Answer : How to Reset a Circuit Breaker All is well with the lights and your electrical appliances one minute, then everything falls into pitch-black darkness the next moment. When a room in your house ... electrical fires. With these tips, a power surge does not have to be a permanent inconvenience.

Why won't my smoke detector stop intermittently beeping?

Description : Why won't my smoke detector stop intermittently beeping?

Last Answer : That sounds like it’s not getting power from the hard wired source. The battery may be low again. Change the battery. If it stops beeping, you probably need an electrician to check the wiring. And welcome to fluther. Oh, and does it only beep in the morning?

Weird problem with my Car's A/C. Any Suggestions?

Description : Weird problem with my Car's A/C. Any Suggestions?

Last Answer : answer:

Tips for managing electrical devices while traveling?

Description : Tips for managing electrical devices while traveling?

Last Answer : answer:I used to travel with about the same amount of equipment and cords for work. Using a computer bag with lots of pockets helps. Labeling each pocket with what is kept in it is a good way for a ... as the desk lamp base (if available), the ones above the bathroom counter, and ones near the door.

Electrical Wiring Who Say ?

Last Answer : Wire Through In load ( e.g. fan , lamp ) Etc. ) electric Power Supply To do Ordinary To the system Electric Waring Says. General In a sense Load Electric Power Supply To do For Of wires Ordinary In the system Being Electric Waring.

Basic electrical and electronics engineering practicals for diploma 22310 MSBTE

Description : 1.Determine the permeability of magnetic material by plotting its BH curve 2. Measure voltage, current and power in 1-phase circuit with resistive load. 3. Measure voltage, current and ... .Make Star and Delta connection in induction motor starters and measure the line and phase values.

Last Answer : Practical no. 6 Aim: Make Star and Delta connection in induction motor starters and measure the line and phase values. Apparatus required:  voltmeter, ammeter, induction motor Circuit diagram ... Result: Hence we have measured the line and phase value of star and delta connection.

What are the common sizes of circuit breaker panel for all electrical home?

Description : What are the common sizes of circuit breaker panel for all electrical home?

Last Answer : 200 amp is the most common size used in most homes.

How long were you in your relationship before the question was popped? Before you got married?

Description : How long were you in your relationship before the question was popped? Before you got married?

Last Answer : We knew each other about a month before we started dating. After we dated two weeks he asked me to marry him. We got married about four months later. we’ve been married 11 years.

How to connect traffic light circuit with road spikes?

Description : How to connect traffic light circuit with road spikes?

Last Answer : Baaad idea, but easily done using the same control system for the lights. It’s never been done because well, it’s a really bad idea.

Black substance on circuit boards?

Description : Black substance on circuit boards?

Last Answer : We coat all our circuits with a conformal coating to protect the leads and contacts to protect them from environmental issues. At the speeds the circuits are running, any two neighboring leads act as ... The added step costs money but it is well worth it for the manufacturer and the customer.

Why is the electronic circuit called "buck" converter?

Description : Why is the electronic circuit called "buck" converter?

Last Answer : answer:http://en.wikipedia.org/wiki/Bucking Basically… the converter uses the Inductor to “buck” the voltage up. That is… when the switch is opened, the inductor “bucks”, increasing the voltage.

circuit I mean What ?

Last Answer : electricity Source , conductor , control Instruments , Usage Machines , Protection Machines In combination Such A Path Whose The middle With Current Flowing To be Can Him Circuit Or Circuit Says.

Define an Integrated circuit.

Description : Define an Integrated circuit.

Last Answer : An integrated circuit(IC) is a miniature ,low cost electronic circuit consisting of active and passive components fabricated together on a single crystal of silicon.The active components are transistors and diodes and passive components are resistors and capacitors. 

what is drive circuit in power electronics ?

Description : What is drive circuit in power electronics?

Last Answer : Driver is used for Motion Control through the use of power electronics.

Why will too many electrical devices operating at one time after blow a fuse or trip a circuit breaker?

Description : Why will too many electrical devices operating at one time after blow a fuse or trip a circuit breaker?

Last Answer : The load exceeds the limit of the breaker or fuse. For example a20 amp breaker on a 120 volt circuit will handle 2400 watts. Exceedthat wattage and the breaker will trip or the fuse will blow.

Before any work on electrical or electronic equipment is performed, which of the following precautions should be carried out? A. De-energize the applicable switchboard bus. B. Bypass the interlocks. C. Secure and tag the supply circuit breaker in the open position. D. Station a man at the circuit supply switch.

Description : Before any work on electrical or electronic equipment is performed, which of the following precautions should be carried out? A. De-energize the applicable switchboard bus. B. Bypass the interlocks. C. ... supply circuit breaker in the open position. D. Station a man at the circuit supply switch.

Last Answer : Answer: C

To remove an alternator operating in parallel with another unit from the main electrical bus, you must FIRST _________. A. adjust the power factor on both units B. set the desired voltage on the outgoing alternator C. open the circuit breaker on the outgoing alternator D. remove the load from the outgoing alternator

Description : To remove an alternator operating in parallel with another unit from the main electrical bus, you must FIRST _________. A. adjust the power factor on both units B. set the desired voltage on ... C. open the circuit breaker on the outgoing alternator D. remove the load from the outgoing alternator

Last Answer : Answer: D

A ground in an electrical circuit outside the engine room _____________. A. cannot be detected under normal conditions B. is of no consequence to engineering personnel C. is indicated at the branch circuit breaker panel D. is indicated by the ground detecting lamps on the main switchboard

Description : A ground in an electrical circuit outside the engine room _____________. A. cannot be detected under normal conditions B. is of no consequence to engineering personnel C. is indicated at the branch circuit breaker panel D. is indicated by the ground detecting lamps on the main switchboard

Last Answer : Answer: D

Electrical circuits are protected against overheating by means of a/an ______________. A. circuit breaker B. amplifier C. diode D. capacitor

Description : Electrical circuits are protected against overheating by means of a/an ______________. A. circuit breaker B. amplifier C. diode D. capacitor

Last Answer : Answer: A

A ground can be defined as an electrical connection between the wiring of a motor and its ____________. A. shunt field B. circuit breaker C. metal framework D. interpole

Description : A ground can be defined as an electrical connection between the wiring of a motor and its ____________. A. shunt field B. circuit breaker C. metal framework D. interpole

Last Answer : Answer: C

A circuit breaker is designed to protect an electrical circuit from damage caused by :

Description : A circuit breaker is designed to protect an electrical circuit from damage caused by :  (A) Over load (B) Short circuit (C) Over current (D) All of the above

Last Answer : A circuit breaker is designed to protect an electrical circuit from damage caused by :  (A) Over load (B) Short circuit (C) Over current (D) All of the above

What's a quick, easy and inexpensive way to boost the am/fm signal to my home radio?

Description : What's a quick, easy and inexpensive way to boost the am/fm signal to my home radio?

Last Answer : These are rated pretty high by customer reviews, it only does FM. if you don’t like it it can be returned for a refund. http://www.amazon.com/Terk-Outdoor-Dual-Drive-Amplified-Antenna/dp/B00009UHYQ/ref=sr_1_1?ie=UTF8&qid=1422930976&sr=8-1&keywords=terk+fm+50

Has anyone ever used Mini Cameras to catch a thief in their home?

Description : Has anyone ever used Mini Cameras to catch a thief in their home?

Last Answer : The Spy Store

If you’re charging a cellular phone using a home outlet, wouldn’t the more powerful current charge a phone faster than using a vehicle’s power to charge the same cellular phone?

Description : If you’re charging a cellular phone using a home outlet, wouldn’t the more powerful current charge a phone faster than using a vehicle’s power to charge the same cellular phone?

Last Answer : Do you understand the difference between AC and DC?

Best Cordless Phone for home?

Description : Best Cordless Phone for home?

Last Answer : I thought this question was interesting, as I honestly do not know many people who still have land lines. Out of curiosity - do you have a cell phone and if so, why ... amazon.com/Panasonic-Handset-Cordless-Answering-KX-TG1033S/dp/B000LYAX1G/ref=sr_1_1?ie=UTF8&s=electronics&qid=1224077093&sr=8-1

Besides food, what things have you made at home? How and where in the house did you make them?

Description : Besides food, what things have you made at home? How and where in the house did you make them?

Last Answer : That question sets me up for some scatological humor, but I’ll be good. This time.

What is the so-called "notch" on an iPhone?

Description : What is the so-called "notch" on an iPhone?

Last Answer : It is a small cutout in the screen, where the front facing camera is located. It is hated, because it reduces usable screen space at the top. Imagine a webcam on top of your monitor, but instead of being actually on top, it hangs down into the screen, obscuring part of it.

A camcorder battery plate claims that the unit stores 2700mAHr at 7.2v.What is the total charge and energy stored?

Description : A camcorder battery plate claims that the unit stores 2700mAHr at 7.2v.What is the total charge and energy stored?

Last Answer : Homework?

Can anyone recommend a portable radio?

Description : Can anyone recommend a portable radio?

Last Answer : C Crane, Sangean and Eton are all quality brands. For almost 20 years I have been using something extremely similar to this: CC Skywave AM, FM, Shortwave, Weather + Alert and VHF ... /FM/Shortwave Radio $24.99 Here are some NY Times Wirecutter recommendations: The Best Emergency Weather Radio

Can one turn a profit by scavenging materials from landfills?

Description : Can one turn a profit by scavenging materials from landfills?

Last Answer : Most have laws against doing any scavenging. Had a friend that lost his jobs in early 1990's (he was VP of insurance company that collapsed) he made a living driving around affluent neighbors picking-up ... wooden box that was crushed but still locked - - surprise 3 gold rings one was worth $2000 !

What is "dirty power" and is my space heater generating it?

Description : What is "dirty power" and is my space heater generating it?

Last Answer : Harmonics, they are the source of this dirty power you speak of. DC switching power supplies are some of the worst offenders. These are transients and non 60hz frequencies that are generated by said appliance. ... your heater works but I'm guessing it uses some sort of switching to run on low power.

Any ideas on how to get a spider out of the CD player in my car?

Description : Any ideas on how to get a spider out of the CD player in my car?

Last Answer : Might want to use a hair dryer for a short time to encourage it to leave. Then, use a cd cleaning disc to remove the webbing and polish the lens.

What is happening when the engine cuts off on a newer vehicle?

Description : What is happening when the engine cuts off on a newer vehicle?

Last Answer : The engine does indeed stop and your accessories are powered by the battery. When you step on the throttle the battery sends high current to the starter which is strong enough to spin the engine up to speed. ... nice write-up in the GM system. They were one of the first to try it. Stop Start System

Is there a Headset/Gaming Headset that works for most platforms?

Description : Is there a Headset/Gaming Headset that works for most platforms?

Last Answer : Turtle Beach makes a lot of sets that work across platforms. Their stuff is pretty quality too.

Do truck manufacturers use standardized wiring harnesses regardless of the model?

Description : Do truck manufacturers use standardized wiring harnesses regardless of the model?

Last Answer : A lot do nut it of course, depends. It’s much easier to use the same harness for each vehicle in the product line. It also makes upgrades easier. This type of thing came up frequently when I was a teenager working in a car audio installation shop.

Why is owning or using a cell phone jammer illegal?

Description : Why is owning or using a cell phone jammer illegal?

Last Answer : answer:Because it disrupts people’s ability to use a communication device. That carries a whole host of potential problems. The only reason to use one is to be a dick.

Is the electronic product affected by a leaky (on the side) battery that has been taped over?

Description : Is the electronic product affected by a leaky (on the side) battery that has been taped over?

Last Answer : answer:If I discovered a leaking battery anywhere, it would go straight into the trash. Batteries cost so little why take unnecessary chances with one that leaks. Makes no sense to me at all.