How over voltage is produced in Field breaker?

How over voltage is produced in Field breaker?
by

1 Answer

Answer :

Over voltages appear if synchronous generators and motors fall out of step inducing an AC voltage in the field system. Depending on the type of construction of the machine and the slip this voltage can become un-permissibly high, for this purpose over voltage protectors are provided in the field breaker cubicle.  
by

Related questions

Electrical jellies! Got a circuit breaker (home) that has popped and won't reset. Suggestions?

Description : Electrical jellies! Got a circuit breaker (home) that has popped and won't reset. Suggestions?

Last Answer : My husband, who was a master electrician, said you need to call a professional. You either have a bad breaker or the breaker that refuses to reset is saving your life because you have a dead short some place and your house would burn down if ithe breaker wasn’t tripped.

My (soon-to-be-replaced) air conditioner is frequently tripping the circuit breaker in my apartment. What can I do to prevent this?

Description : My (soon-to-be-replaced) air conditioner is frequently tripping the circuit breaker in my apartment. What can I do to prevent this?

Last Answer : answer:A mini-split AC unit will use less power than a regular square version and should help with the problem. However if your problem resides in old wiring with a lower amperage/threshold you might ... every time you want to use it but this has cut my electric bill dramatically. Hope this helps

What is the advantage of field forcing in the rotor?

Description : What is the advantage of field forcing in the rotor?  

Last Answer : Field forcing acts for 10 seconds to maintain the generator terminal voltage during fault condition so as to operated the protection relays. 

What is material used in making non-linear resistor & purpose of it in field discharge resistor?

Description : What is material used in making non-linear resistor & purpose of it in field discharge resistor?  

Last Answer : Silicon carbide materials used for making non-linear resistor. The purpose of this resistor is to avoid surge voltage when field breaker opens. These resistors are connected in parallel to the main field winding (Rotor). 

An AC generator operating in parallel loses its excitation without tripping the circuit breaker. This will __________. A. not affect the faulty generator due to the compensation of the other generators B. cause the slip rings to melt C. cause a low voltage differential to develop between the armature and the bus D. cause high currents to be induced in the field windings

Description : An AC generator operating in parallel loses its excitation without tripping the circuit breaker. This will __________. A. not affect the faulty generator due to the compensation of the other generators B. ... between the armature and the bus D. cause high currents to be induced in the field windings

Last Answer : Answer: D

When securing an AC generator, you should FIRST ___________. A. open the generator circuit breaker B. switch the voltage regulator to 'manual' C. decrease the field excitation to minimum D. reduce the load on the unit

Description : When securing an AC generator, you should FIRST ___________. A. open the generator circuit breaker B. switch the voltage regulator to 'manual' C. decrease the field excitation to minimum D. reduce the load on the unit

Last Answer : Answer: D

What is bias voltage?

Description : What is bias voltage?

Last Answer : The external voltage applied to make p-n junction biased is called bias voltage.

When the Zero sequence reactance arises?

Description : When the Zero sequence reactance arises? 

Last Answer : If a machine is operating with an earthed neutral, a system earth fault will give rise to zero sequence current in the machine. 

When the negative sequence reactance arises?

Description : When the negative sequence reactance arises?

Last Answer : Negative sequence arises whenever there is any unbalance present in the system. Their effect is to set up a field rotating in opposite direction to the main field.

What is the advantage of Static Excitation?

Description : What is the advantage of Static Excitation?  

Last Answer : Fast response time, high reliability, interchangeability of parts during operation, less wear & tear due to static devices & less maintenance.  

What is purpose of reactive power (VAR)?

Description : What is purpose of reactive power (VAR)?  

Last Answer : It is an energy required to built up magnetic field to drive the power.  

What is purpose of Slip stabilization?

Description : What is purpose of Slip stabilization?  

Last Answer : It avoids oscillation of the AC machine (Rotor oscillations).  

What is purpose of Stator current limiter?

Description : What is purpose of Stator current limiter?  

Last Answer : It limits the stator current.

What is purpose of Rotor current limiter?

Description : What is purpose of Rotor current limiter?

Last Answer : It limits overloading of rotor.  

What is purpose of Rotor angle limiter?

Description : What is purpose of Rotor angle limiter?

Last Answer : It limits generator voltage & rotor voltage.  

What is purpose of Load angle limiter?

Description : What is purpose of Load angle limiter?  

Last Answer : Load angle limiter, it either limits the angle between grid load center and the rotor axis or generator terminal & rotor axis. 

What is purpose of connecting thyristor bridges in parallel?

Description : What is purpose of connecting thyristor bridges in parallel?

Last Answer : Thyristor bridges are connected in parallel to improve current rating.  

Why reactors are provided in Thyristor bridges?

Description : Why reactors are provided in Thyristor bridges? 

Last Answer : Reactors are provided to limit the rate of rise of current (di/dt) in the device, thereby avoiding possible damage to the device. They also effect a proper sharing of load among thyristor bridges when connected in parallel. 

What is the purpose of RC network across thyristor?

Description : What is the purpose of RC network across thyristor?

Last Answer : RC network across each thyristor protects against Hole Storage Effect.  

What is Inverter operation?

Description : What is Inverter operation? 

Last Answer : When firing angle a = 90º the positive & negative voltages areas are equal. With a higher than 90º the negative areas are greater so the total voltage becomes negative. This condition is termed as 'Inverter Operation".  

What is firing angle?

Description : What is firing angle? 

Last Answer : The angle in the AC cycle at which the thyristor starts conducting at the application of positive voltage to gate is known as the firing angle (α)

What is material used in making semiconductor?

Description : What is material used in making semiconductor?

Last Answer : Silicon & Germanium are the raw materials used for making semiconductor. Semiconductors are located between conductors & insulators in the resistivity spectrum & allow current to flow only under certain conditions. 

What is Thyristor?

Description : What is Thyristor?

Last Answer : Thyristor is a four or more layer semiconductor device & having 3 or more junctions. It is also called Silicon Controlled Rectifiers (SCR). A healthy SCR must block in both the directions at least 1MΩ resistance, a fused SCR will conducts in both directions. 

What is Diode?

Description : What is Diode?

Last Answer : Diode is a two-layer semiconductor device, conducts only positive cycles when applied to anode

The arc voltage produced in A.C. circuit breaker is always (a) in phase with the arc current (b) lagging the arc current by 90" (c) leading the arc current by 90° (d) none of the above

Description : The arc voltage produced in A.C. circuit breaker is always (a) in phase with the arc current (b) lagging the arc current by 90" (c) leading the arc current by 90° (d) none of the above

Last Answer : (a) in phase with the arc current

The arc voltage produced in A.C. circuit breaker is always?

Last Answer : The arc voltage produced in A.C. circuit breaker is always in phase with the arc current.

Voltage failure of an AC generator may be caused by ____________. A. failure of the exciter generator B. a tripped bus circuit breaker C. high mica segments on the stator bus bar D. excessive prime mover speed

Description : Voltage failure of an AC generator may be caused by ____________. A. failure of the exciter generator B. a tripped bus circuit breaker C. high mica segments on the stator bus bar D. excessive prime mover speed

Last Answer : Answer: A

Which of the following actions must be carried out prior to closing the alternator circuit breaker according to the graph shown in the illustration? EL-0002 A. Increase the alternator voltage. B. Decrease the line voltage. C. Increase the line voltage. D. Decrease the line frequency.

Description : Which of the following actions must be carried out prior to closing the alternator circuit breaker according to the graph shown in the illustration? EL-0002 A. Increase the alternator voltage. B. Decrease the line voltage. C. Increase the line voltage. D. Decrease the line frequency.

Last Answer : Answer: A

An alternator will fail to produce line voltage as a result of _____________. A. a closed circuit breaker B. oxidized slip rings C. improperly staggered brushes D. exciter generator failure

Description : An alternator will fail to produce line voltage as a result of _____________. A. a closed circuit breaker B. oxidized slip rings C. improperly staggered brushes D. exciter generator failure

Last Answer : Answer: D

To remove an alternator operating in parallel with another unit from the main electrical bus, you must FIRST _________. A. adjust the power factor on both units B. set the desired voltage on the outgoing alternator C. open the circuit breaker on the outgoing alternator D. remove the load from the outgoing alternator

Description : To remove an alternator operating in parallel with another unit from the main electrical bus, you must FIRST _________. A. adjust the power factor on both units B. set the desired voltage on ... C. open the circuit breaker on the outgoing alternator D. remove the load from the outgoing alternator

Last Answer : Answer: D

After closing the circuit breaker to place two similar alternators in parallel, the NEXT step is to balance the _____________. A. power factor B. voltage load C. kilowatt load D. ampere load

Description : After closing the circuit breaker to place two similar alternators in parallel, the NEXT step is to balance the _____________. A. power factor B. voltage load C. kilowatt load D. ampere load

Last Answer : Answer: C

When paralleling two AC generators, the frequency of the machine coming online, immediately prior to closing its breaker, should be ____________. A. slightly less than the oncoming generator frequency B. the same as the bus frequency C. slightly greater than the bus frequency D. the same as the bus voltage

Description : When paralleling two AC generators, the frequency of the machine coming online, immediately prior to closing its breaker, should be ____________. A. slightly less than the oncoming generator frequency B. the ... bus frequency C. slightly greater than the bus frequency D. the same as the bus voltage

Last Answer : Answer: C

When paralleling two AC generators, the frequency of the incoming machine immediately prior to closing its breaker should be ____________. A. controlled by placing the governor switch in the automatic position B. adjusted with the voltage regulator C. slightly greater than the bus frequency D. slightly less than the bus frequency

Description : When paralleling two AC generators, the frequency of the incoming machine immediately prior to closing its breaker should be ____________. A. controlled by placing the governor switch in the automatic ... regulator C. slightly greater than the bus frequency D. slightly less than the bus frequency

Last Answer : Answer: C

Undervoltage trips are frequently installed on switchboard circuit breakers to trip ____________. A. out generators in the event of severe arcing or sparking B. out generators when there is reversal of power in the main circuit C. the breaker if the generator overspeeds by 5%, but continues to run D. out generators when there is low voltage in the main circuit

Description : Undervoltage trips are frequently installed on switchboard circuit breakers to trip ____________. A. out generators in the event of severe arcing or sparking B. out generators when there is reversal of power ... , but continues to run D. out generators when there is low voltage in the main circuit

Last Answer : Answer: D

A device which can be used to check the calibration of a circuit breaker is a _________________. A. 500 volt megohmmeter B. portable low voltage high current testing unit C. standard digital multimeter D. clamp-on voltmeter

Description : A device which can be used to check the calibration of a circuit breaker is a _________________. A. 500 volt megohmmeter B. portable low voltage high current testing unit C. standard digital multimeter D. clamp-on voltmeter

Last Answer : Answer: B

You are attempting to parallel two AC generators and the synchroscope pointer stops at a position other than 0°. If you close the circuit breaker at this moment _____________. A. the incoming machine will accept all of the load B. the incoming machine will trip out on low voltage release C. a hazardous condition will be created by the cross current between the machines D. a hazardous condition will be created by the incoming machine being at a higher frequency than the bus

Description : You are attempting to parallel two AC generators and the synchroscope pointer stops at a position other than 0°. If you close the circuit breaker at this moment _____________. A. the incoming ... hazardous condition will be created by the incoming machine being at a higher frequency than the bus

Last Answer : Answer: C

The purpose of a main switchboard circuit breaker's reverse-power trip is to _____________. A. prevent main circuit overload B. protect the circuit breaker blowout coil C. prevent alternator motorization D. prevent low voltage tripout

Description : The purpose of a main switchboard circuit breaker's reverse-power trip is to _____________. A. prevent main circuit overload B. protect the circuit breaker blowout coil C. prevent alternator motorization D. prevent low voltage tripout

Last Answer : Answer: C

What is recovery voltage in circuit breaker?

Description : What is recovery voltage in circuit breaker?

Last Answer : Recovery voltage in circuit breakers is defined as the power frequency rms voltage which appears across the breaker contacts after the transient oscillations die out and the final extinction of the arc ... poles of the circuit breaker. It is the voltage developed after the arc extinction is competed

Is the electronic product affected by a leaky (on the side) battery that has been taped over?

Description : Is the electronic product affected by a leaky (on the side) battery that has been taped over?

Last Answer : answer:If I discovered a leaking battery anywhere, it would go straight into the trash. Batteries cost so little why take unnecessary chances with one that leaks. Makes no sense to me at all.

It there anything other than old age that makes one more appreciative of getting warm sock, nice gloves, or an umbrella for ********* over gadgets?

Description : It there anything other than old age that makes one more appreciative of getting warm sock, nice gloves, or an umbrella for Christmas over gadgets?

Last Answer : I think it’s due to being old. As a child, I didn’t care for practical gifts the way you didn’t. As an adult, I do now.

How much does verizon charge for over used data?

Description : How much does verizon charge for over used data?

Last Answer : One Biiilllion Dollars.

Best over-ear headphones for under $100?

Description : Best over-ear headphones for under $100?

Last Answer : Sennheiser HD555

Why would you chose the Nexus One over the Droid?

Description : Why would you chose the Nexus One over the Droid?

Last Answer : First I'll tell you why the Droid is bad. The physical keyboard is terrible. It's heavy, square, and chunky. The camera takes forever to boot up. Now, why is the Nexus One better? It has a better ... I would choose the N1. I also suggest looking at the Droid Eris which I also prefer over the Droid.

How can I keep my power cords, charging docks, and various other electronics related cords from taking over all of my extra storage space?

Description : How can I keep my power cords, charging docks, and various other electronics related cords from taking over all of my extra storage space?

Last Answer : I use twisty ties because I’m ghetto. But it looks like the Container Store has a bunch of options. I’d imagine most office supplies stores would have stuff too.

Can you bring a phone number over when switching from verizon to AT&T?

Description : Can you bring a phone number over when switching from verizon to AT&T?

Last Answer : Haha, yea. Unless it’s in use.

Why do chargers over charge?

Description : Why do chargers over charge?

Last Answer : answer:well I wouldn't necessarily say it over charges more like, it takes it to a full 100% charge, and the moment it drops to 99%, it charges it again .I've never seen my phone go past 100% ... green light to indicate a full charge, and and orange/red light if it is charging still. Hope it helped.

In the illustration, the purpose of part B is to _________. EL-0033 A. increase resistance in series with the contacts as they close to prevent arcing B. create a magnetic field in the steel plates that interacts with the arc to cool and extinguish the arc C. cause the contacts to open in the event of an overload D. provide ventilation to the contact when the breaker is close to rated capacity

Description : In the illustration, the purpose of part B is to _________. EL-0033 A. increase resistance in series with the contacts as they close to prevent arcing B. create a magnetic field in the steel ... event of an overload D. provide ventilation to the contact when the breaker is close to rated capacity

Last Answer : Answer: B

A ground can be defined as an electrical connection between the wiring of a motor and its ____________. A. shunt field B. circuit breaker C. metal framework D. interpole

Description : A ground can be defined as an electrical connection between the wiring of a motor and its ____________. A. shunt field B. circuit breaker C. metal framework D. interpole

Last Answer : Answer: C

What are the logics adopted to close the field breaker?

Description : What are the logics adopted to close the field breaker? 

Last Answer : a) Turbine speed 2880 rpm. b) Class A, B and BG trip reset. c) Auto/manual reference minimum. d) Auto/manual channels supply normal. e) FB closing circuit healthy.