Description : What three factors must be considered in the transmission of a surface wave to reduce attenuation?
Last Answer : (a) electrical properties of the terrain (b) frequency (c) polarization of the antenna
Description : Is the attenuation of a coaxial cable independent of frequency?
Last Answer : No.
Description : If the length of the fiber point defect changes with pulse duration, is the OTDR signal deviation a point defect or a region of high fiber attenuation?
Last Answer : A point defect.
Description : Why is a dead-zone fiber placed between the test fiber and OTDR when conducting attenuation measurements?
Last Answer : To reduce the effect of the initial reflection at the OTDR
Description : in multimode fibers, how do fiber joints increase fiber attenuation following the joint?
Last Answer : By disturbing the fiber's mode power distribution (MPD).
Description : What two properties of the launch condition may affect multimode fiber attenuation measurements?
Last Answer : . Launch spot size and angular distribution.
Description : Will an optical fiber's attenuation coefficient vary with changes in wavelength?
Last Answer : Yes.
Description : Attenuation is mainly a result of what three properties?
Last Answer : Light absorption, scattering, and bending losses.
Description : Reduction of signal strength during transmission is called attenuation. -Technology
Last Answer : TrueDuring transmission, the signal strength is reduced, this phenomenon is called attenuation.
Description : What is attenuation ?
Last Answer : Natural behavior of an organism without causing disease is called attenuation i.e. reducing pathogenesity of the organism.
Description : Which of the following parameters is not a primary parameter? a) Resistance b) Attenuation constant c) Capacitance d) Conductance
Last Answer : Ans: B
Description : A special request originated from some device to the CPU to acquire some of its time is called ___________ a) Disturbance b) Attenuation c) Interrupt d) Noise
Last Answer : Answer: c Explanation: An interrupt is a kind of request which takes control of the system bus for some time, then performs all the operations and gives back control to the CPU. It is usually identified by some number and is handled by the interrupt controller
Description : The upper pulse rate and information carrying capacity of a cable is limited by a. Pulse shortening b. Attenuation c. Light leakage d. Modal dispersion
Last Answer : d. Modal dispersion
Description : Which of the cable length has the highest attenuation? a. 1 km b. 2 km c. 95 ft d. 5500 ft
Last Answer : b. 2 km
Description : Cable attenuation is usually expressed in terms of a. Loss per foot b. dB/km c. intensity per mile d. voltage drop per inch
Last Answer : b. dB/km
Description : The loss in signal power as light travels down a fiber is called a. Dispersion b. Scattering c. Absorption d. Attenuation
Last Answer : d. Attenuation
Description : What is the free space attenuation of a satellite communications system operating at 36,000 km above the earth at 5.0 GHz? A. 198 dB B. 202 dB C. 142 dB D. 138 dB
Last Answer : A. 198 dB
Description : _________ is the random and unpredictable electric signals from natural causes, both internal and external to the system. A. Interference B. Attenuation C. Distortion D. Noise
Last Answer : D. Noise
Description : What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000
Last Answer : C. 125,000
Description : Atmospheric attenuation is an attenuation which is due to A. mist and fog B. gasses in the atmosphere C. water vapor and oxygen D. rain
Last Answer : C. water vapor and oxygen
Description : Which of the following phenomena is possible is free space medium? A. Reflection of radio wave B. Diffraction of radio wave C. Refraction of radio wave D. Attenuation of radio wave
Last Answer : D. Attenuation of radio wave
Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.
Last Answer : D. an impedance mismatch between the load and the line.
Description : What is the amount of sound reduction provided by a barrier – wall, floor, or ceiling called? A. Sound Attenuation B. Transmission loss C. Sound absorption D. Barrier loss
Last Answer : B. Transmission loss
Description : What is the current frequency band given most attenuation for satellite communications? A. Ku B. C band C. J D. P
Last Answer : A. Ku
Description : What is the path attenuation between transmitter and receiver at a frequency of 1.2 Ghz and a distance of 11,000 mi? A. 119 dB B. 115dB C. 179dB D. 174dB
Last Answer : C. 179dB
Description : Loss due to the diffraction of light when it strikes on the irregularities formed during the manufacturing process of the fiber optics. A. Absorption loss B. Attenuation C. Bending loss D. Rayleigh scattering loss
Last Answer : D. Rayleigh scattering loss
Description : What frequency does oxygen causes excessive attenuation A. 119 GHz B. 183 GHz C. 310 GHz D. 60 GHz
Last Answer : D. 60 GHz
Description : Which is atmospheric attenuation? A. Attenuation due to rain B. Attenuation due to other gasses C. Attenuation due to mist and fog D. Due to water vapor and oxygen
Last Answer : D. Due to water vapor and oxygen
Description : The random and unpredictable electric signal from natural causes, both internal and external to the system is know as ________. A. Distortion B. Noise C. Attenuation D. Interference
Last Answer : B. Noise
Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts
Last Answer : B. 2.656 watts
Last Answer : A. PAM
Description : ECE Board Exam November 1996 The loss in signal power as light travels down a fiber is A. attenuation B. propagation C. absorption D. scattering
Last Answer : A. attenuation
Description : Phenomena in which signal transmitted in one circuit creates undesired effect in other circuit is known as A. crosstalk B. signal attenuation C. sampling D. crosslinking
Last Answer : crosslinking
Description : Decrease in strength of signal is known as A. tuning B. modulation C. attenuation D. amplification
Last Answer : attenuation
Description : The loss in signal power as light travels down the fiber is called a. attenuation b. progragation c. scattering d. interruption
Description : Block coding can help in _______at the receiver. A) Synchronization B) Error detection C) Attenuation D) (a) and (b)
Last Answer : (a) and (b)
Description : _________can impair a signal. A) Attenuation B) Distortion C) Noise D) All of theabove
Last Answer : All of theabove
Description : _______ is a typeof transmission impairment in which an outside sourcesuch as crosstalk corrupts asignal. A) Attenuation B) Distortion C) Noise D) Decibel
Last Answer : Noise
Description : ________ is a typeof transmission impairment in which the signal loses strength due to the different propagation speeds of each frequency that makes up the signal. A) Attenuation B) Distortion C) Noise D) Decibel
Last Answer : Distortion
Description : ________ is a typeof transmission impairment in which the signal loses strength due to theresistance of the transmission medium. A) Attenuation B) Distortion C) Noise D) Decibel
Last Answer : Attenuation
Description : The attenuation constant is 0.5 units. The skin depth will be a) 0.5 b) 0.25 c) 2 d) 4
Last Answer : c) 2
Description : The attenuation in a good dielectric will be non- zero. State True/False. a) True b) False
Last Answer : a) True
Description : In pure dielectrics, the parameter that is zero is a) Attenuation b) Propagation c) Conductivity d) Resistivity
Last Answer : c) Conductivity
Description : The phase shift in the electric and magnetic fields in an EM wave is given by which parameter? a) phase constant b) attenuation constant c) propagation constant d) intrinsic impedance
Last Answer : d) intrinsic impedance
Description : The skin depth of a conductor with attenuation constant of 7 neper/m is a) 14 b) 49 c) 7 d) 1/7
Last Answer : d) 1/7
Description : Calculate the attenuation constant of a conductor of conductivity 200 units, frequency 1M radian/s in air. a) 11.2 b) 1.12 c) 56.23 d) 5.62
Last Answer : a) 11.2
Description : Calculate the phase constant of a conductor with attenuation constant given by 0.04 units. a) 0.02 b) 0.08 c) 0.0016 d) 0.04
Last Answer : d) 0.04
Description : In free space, the condition that holds good is a) Minimum attenuation and propagation b) Minimum attenuation and maximum propagation c) Maximum attenuation and minimum propagation d) Maximum attenuation and propagation
Last Answer : b) Minimum attenuation and maximum propagation
Description : The attenuation constant in lossless dielectrics will be a) 0 b) 1 c) -1 d) ∞
Last Answer : a) 0
Description : In conductors, which two parameters are same? a) Wavelength and phase constant b) Phase and attenuation constant c) Attenuation constant and skin depth d) Skin depth and wavelength
Last Answer : b) Phase and attenuation constant