Description : Identify the components labelled A, B, C and D in the diagram below from the list (i) to (vii) given along with Components : (i) Cristae of mitochondr
Last Answer : Identify the components labelled A, B, C and D in the diagram below from the list (i) to (vii) given along with ... v)","(iv)","(viii)","(iii)"):}`
Description : Identify the components labelled A, B, C and D in the diagram below from the list (i) to (viii) given along with Components : (i) Cristae of mitochondria (ii) Inner membrane of mitochondria (iii) Cytoplasm (iv) Smooth endoplasmic ... viii) (vi) (c) (vi) (v) (iv) (vii) (d) (v) (i) (iii) (ii)
Last Answer : (a) (v) (iv) (viii) (iii)
Description : What type of diagram is the most useful in learning the overall operation of a system?
Last Answer : A schematic diagram.
Description : Components made up exclusively of discrete elements are classified as what type of electronics?
Last Answer : Miniature.
Description : What components in an electrodynamometer-type meter movement produce the magnetic field?
Last Answer : Fixed coils.
Description : What two components make up a simple synchro transmission system?
Last Answer : A synchro transmitter and a synchro receiver.
Description : List five system design parameters considered when system designers choose the system operational wavelength and link components.
Last Answer : Launch power, connection losses, bandwidth, cost, and reliability
Description : What are the essential components of a cw receiver system?
Last Answer : An antenna, tank circuit for tuning, rectifier for detection, filter to give constant output, and an indicator device
Description : What type of flux must be used in all electrical and electronic soldering?
Last Answer : Noncorrosive, nonconductive rosin fluxes.
Description : The domain in a gallium-arsenide semiconductor has what type of electrical field when compared to the other regions across the body of a semiconductor?
Last Answer : A field of much greater intensity.
Description : What type of diagram would be most useful for wiring a relay into a circuit?
Last Answer : . Terminal diagram.
Description : What type of diagram is the most detailed?
Last Answer : Wiring diagram.
Description : On the diagram below, name the elements of the vacuum tube and their potentials relative to dc ground. time is an example of what type of transmission?
Last Answer : a. Plate, positive. b. Suppressor grid, negative.
Description : Which type of flux should be used when soldering electrical wire connections and electronic components? A. Silver flux B. Rosin flux C. Solid flux D. Acid flux
Last Answer : Answer: B
Description : Who is responsible for meeting environmental and electrical requirements of a system?
Last Answer : Equipment designers (planners).
Description : The transmission of still images over an electrical communications system is known as what?
Last Answer : Facsimile.
Description : Why must a wiring diagram be used in conjunction with a schematic to troubleshoot a system?
Last Answer : To find the test points.
Description : What system is currently used by all branches of the military to identify test equipment?
Last Answer : Joint Electronics Type Designation System (JETDS).
Description : A switchboard, for a AC electrical distribution system, will be provided with which of the following components? A. Frequency meter. B. Ammeter C. Voltmeter D. All of the above
Last Answer : Answer: D
Description : Explain the use of the following components in electrical wiring system and give specification of each: (i) MCB (ii) ELCB
Last Answer : i) MCB (Miniature Circuit Breaker) * MCB provides short circuit protection. * MCB provides overload protection * ELCB provides earth fault protection. * MCB is in series with load and ELCB is ... The low sensitivity ELCB are used for electrical machine the rating is in between the 3A to 10 A
Description : Draw block diagram of pneumatic system showing its basic components. State the functions of control value and air actuator.
Last Answer : Diagram : Control valve: - control and regulates the direction of flow and pressure etc. Air actuator: - Air cylinders and motors are used to obtain the required movements of direction flow.
Description : A soldering gun should NOT be used on what components?
Last Answer : Electronic components, such as resistors, capacitors, and transistors.
Description : In an astable multivibrator, which components determine the pulse repetition frequency?
Last Answer : RC coupling networks.
Description : . What components form the load for Q1?
Last Answer : C5 and the primary of T2.
Description : What components form the input-signal-developing impedance for the amplifier?
Last Answer : C2 and the secondary of T1.
Description : What is the arrangement of both series and shunt components called?
Last Answer : Combination peaking.
Description : What determines whether these components are considered series or shunt?
Last Answer : . The relationship of the components to the output-signal path.
Description : What compone What components What components can be used to increase the high frequency response of an amplifier?
Last Answer : Peaking coils.
Description : What are the two major components of a synchro?
Last Answer : The rotor and the stator.
Description : What the three basic components make up the typical magnetic amplifier?
Last Answer : Two saturable reactors and a transformer.
Description : Which components provide the regenerative feedback signal in the phase-shift oscillator?
Last Answer : Resistor-capacitor networks.
Description : List two causes of damage to ESD-sensitive electronic components
Last Answer : Esd, improper stowage, and improper handling.
Description : How do you prevent excessive heat buildup on an area of a board when soldering multilead components?
Last Answer : Use a skipping pattern
Description : When you replace components, identification marks must meet what requirements?
Last Answer : They should be readable from a single point.
Description : Name the three methods of interconnecting components in multilayer printed circuit boards.
Last Answer : Clearance hole, plated-through hole, and layer build-up
Description : How are thick-film components produced?
Last Answer : Screening
Description : What methods are used to deposit thin-film components on a substrate?
Last Answer : . Evaporation and cathode sputtering.
Description : The ability to place more components in a given space is an advantage of the __
Last Answer : Cordwood module.
Description : Name the components which greatly increase the weight of vacuum-tube circuitry.
Last Answer : Transformers, capacitors, and resistors.
Description : What three components determine the address that locates where on a floppy disk the computer will store the data?
Last Answer : a. disk side number, b. track number, and c. sector number.
Description : A typical satellite communications operational link consists of a satellite and what two other components?
Last Answer : Earth terminals.
Description : What two components give a ssb receiver its advantages over an AM superheterodyne receiver?
Last Answer : A special type of detector and a carrier reinsertion oscillator
Description : List the types of fiber optic components considered part of a fiber optic cable plant.
Last Answer : Optical fiber cables, connectors, splices, mounting panels, jumper cables, and other passive components.
Description : What are the differences between the components of a dc generator and a dc motor?
Last Answer : There are no differences.
Description : There is a relationship between total current and current through the individual components in a circuit. What is this relationship in a series circuit and a parallel circuit?
Last Answer : The source voltage would have to be increased to 640 volts
Description : which components act as the filter network in the diode detector?
Last Answer : C1 and R1.
Description : When you are testing individual components in a circuit, what may cause a defective component to appear good?
Last Answer : A parallel resistor or diode of similar value.
Description : What are the five main components of a circuit breaker?
Last Answer : Frame, operating mechanism, arc extinguishers, terminal connectors, and trip element.
Description : What components may be used to build a basic phase modulator?
Last Answer : A phase-shift network such as a variable resistor and capacitor in series