What components can be used to increase the high frequency response of an amplifier?

What compone What components  What components can be used to increase the high frequency response of an amplifier?
by

1 Answer

Answer :

Peaking coils.
by

Related questions

What is the major factor that limits the high-frequency response of an amplifier circuits?

Description : What is the major factor that limits the high-frequency response of an amplifier circuits?

Last Answer : The capacitance of the circuit.

What component in an amplifier circuit tends to limit the low-frequency response of the amplifier?

Description : What component in an amplifier circuit tends to limit the low-frequency response of the amplifier?

Last Answer : The coupling capacitor (C3).

What are the factors that limit the frequency response of a transistor amplifier?

Description : What are the factors that limit the frequency response of a transistor amplifier?

Last Answer : The capacitance and inductance of the circuit and the interelectrode capacitance of the transistor.

What components form the input-signal-developing impedance for the amplifier?

Description : What components form the input-signal-developing impedance for the amplifier?

Last Answer : C2 and the secondary of T1.

What the three basic components make up the typical magnetic amplifier?

Description : What the three basic components make up the typical magnetic amplifier?

Last Answer : Two saturable reactors and a transformer.

In the illustrated circuit, one advantage of the capacitor coupling over direct coupling is ____________. EL-0048 A. as the frequency decreased the capacitive reactance (Xc) increases B. the amplifier becomes more efficient at lower capacitance. C. the arrangement allows the coupling of the signal while it isolates the biasing of each stage. D. good frequency response.

Description : In the illustrated circuit, one advantage of the capacitor coupling over direct coupling is ____________. EL-0048 A. as the frequency decreased the capacitive reactance (Xc) increases B. the amplifier becomes ... of the signal while it isolates the biasing of each stage. D. good frequency response.

Last Answer : Answer: C

Draw the frequency response of DC amplifier. Comment on it.

Description : Draw the frequency response of DC amplifier. Comment on it.

Last Answer : frequency response: Comment : The gain remains constant at its midband value AM down to zero frequency (DC). Directcoupled amplifiers do not suffer gain reduction at low frequencies as compared ... , gain falls off at the high frequency end due to the internal capacitances of the transistor.

State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Description : State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Last Answer : The need of multistage amplifier The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in ... to use a MULTISTAGE AMPLIFIER .  Frequency response of R-C coupled amplifier.

Can a parallel LC circuit be used as the frequency determining network for an rf amplifier?

Description : Can a parallel LC circuit be used as the frequency determining network for an rf amplifier?

Last Answer : Yes.

What is the purpose of a frequency-determining network in an rf amplifier?

Description : What is the purpose of a frequency-determining network in an rf amplifier?

Last Answer : To provide maximum impedance at the desired frequency.

What are the upper and lower frequency limits of an amplifier?

Description : What are the upper and lower frequency limits of an amplifier?

Last Answer : The half-power points of a frequency-response curve. The upper and lower limits of the band f frequencies for which the amplifier is most effective.

What is the frequency classification of a magnetic amplifier

Description : What is the frequency classification of a magnetic amplifier

Last Answer : An audio (or low) frequency power amplifier.

In a nondegenerative parametric amplifier the difference between the input frequency and the pump frequency is called what?

Description : In a nondegenerative parametric amplifier the difference between the input frequency and the pump frequency is called what?

Last Answer : Idler- or lower-sideband frequency.

The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Description : The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Last Answer : Exactly double the input frequency.

List four factors that can degrade the frequency response of magnetic tape recorders.

Description : List four factors that can degrade the frequency response of magnetic tape recorders.

Last Answer : a. A too-high or too-low bias signal level setting for the record head. b. An improper reproduce head gap. c. An improper tape transport speed. d. Poor tape-to-head contact.

While measuring frequency response, as the signal generator approaches the lowest and highest frequency the recorder can effectively record, the VTVM reading drops to less than - 3 dB. What does this indicate?

Description : While measuring frequency response, as the signal generator approaches the lowest and highest frequency the recorder can effectively record, the VTVM reading drops to less than - 3 dB. What does this indicate?

Last Answer : The upper and lower limits of the frequency response specification for that tape recorder.

The frequency-response specification of your tape recorder reads within +/ - 3 dB from 150 Hz to 150 kHz at 60 ips. What does this mean?

Description : The frequency-response specification of your tape recorder reads within +/ - 3 dB from 150 Hz to 150 kHz at 60 ips. What does this mean?

Last Answer : The recorder can record all frequencies between 150 Hz and 150 kHz at 60 ips without varying the output amplitude more than 3 dB.

Which digital data encoding method helps overcome a tape recorder’s low-frequency response problems by recording two logic levels for each incoming data bit?

Description : Which digital data encoding method helps overcome a tape recorder’s low-frequency response problems by recording two logic levels for each incoming data bit?

Last Answer : Bi-phase level encoding.

The frequency response of test equipment refers to what aspect of ac voltage measurements?

Description : The frequency response of test equipment refers to what aspect of ac voltage measurements?

Last Answer : the range of frequencies that can accurately be measured.

Name the modulation system in which the frequency alternates between two discrete values in response to the opening and closing of a key?

Description : Name the modulation system in which the frequency alternates between two discrete values in response to the opening and closing of a key?

Last Answer : . Frequency-shift keying.

In an astable multivibrator, which components determine the pulse repetition frequency?

Description : In an astable multivibrator, which components determine the pulse repetition frequency?

Last Answer : RC coupling networks.

Name the components which greatly increase the weight of vacuum-tube circuitry.

Description : Name the components which greatly increase the weight of vacuum-tube circuitry.

Last Answer : Transformers, capacitors, and resistors.

Trade-offs between competing effects are necessary for high speed response. Which competing effect (fast transit time, low capacitance, or high quantum efficiency) requires a thin active area?

Description : Trade-offs between competing effects are necessary for high speed response. Which competing effect (fast transit time, low capacitance, or high quantum efficiency) requires a thin active area?

Last Answer : Fast transit time.

How can I reduce the bass response on my car amplifier?

Description : How can I reduce the bass response on my car amplifier?

Last Answer : Try adding a adding a capacitor.

In the illustrated amplifier, the RESET potentiometer A1R2 sets the stability of the control loop by changing the reset time constant. As the potentiometer is turned clockwise _________. EL-0060 A. the gain is increased B. the stability is increased by slowing the response time C. feedback is increased to the summing point at terminal 5 D. response time is increased decreasing stability

Description : In the illustrated amplifier, the RESET potentiometer A1R2 sets the stability of the control loop by changing the reset time constant. As the potentiometer is turned clockwise _________. EL-0060 A. ... is increased to the summing point at terminal 5 D. response time is increased decreasing stability

Last Answer : Answer: B

What is the usual response to digoxin in a patient of atrial fibrillation: A. Restoration of normal sinus rhythm B. Conversion of atrial fibrillation to atrial flutter C. Increase in atrial fibrillation frequency, but decrease in ventricular rate D. Decrease in atrial fibrillation frequency, but increase in ventricular rate

Description : What is the usual response to digoxin in a patient of atrial fibrillation: A. Restoration of normal sinus rhythm B. Conversion of atrial fibrillation to atrial flutter C. Increase in ... decrease in ventricular rate D. Decrease in atrial fibrillation frequency, but increase in ventricular rate

Last Answer : C. Increase in atrial fibrillation frequency, but decrease in ventricular rate

If C4 were removed from the circuit, what would happen to the output of the amplifier?

Description : If C4 were removed from the circuit, what would happen to the output of the amplifier?

Last Answer : The output would decrease. (C4 decouples R2 preventing degenerative feedback from R2.)

What two methods are used to compensate for the problems that cause low gain in an rf amplifier?

Description : What two methods are used to compensate for the problems that cause low gain in an rf amplifier?

Last Answer : . RF transformers are used and the transistor is neutralized.

What problem is caused in an rf amplifier by a loosely coupled transformer?

Description : What problem is caused in an rf amplifier by a loosely coupled transformer?

Last Answer : A too-narrow bandpass.

What is the most common form of coupling for an rf amplifier?

Description : What is the most common form of coupling for an rf amplifier?

Last Answer : Transformer coupling.

If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?

Description : If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?

Last Answer : The gain decreases.

If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?

Description : If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?

Last Answer : The gain increases.

If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Description : If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Last Answer : A step-down transformer.

What is the bandwidth of an amplifier?

Description : What is the bandwidth of an amplifier?

Last Answer : The difference between the upper and lower frequency limits of an amplifier.

When is degeneration tolerable in an amplifier?

Description : When is degeneration tolerable in an amplifier?

Last Answer : When it is necessary to prevent amplitude distortion.

In the basic transistor amplifier discussed earlier, what is the relationship between the polarity of the input and output signals?

Description : In the basic transistor amplifier discussed earlier, what is the relationship between the polarity of the input and output signals?

Last Answer : The signals are opposite in polarity or 180 degrees out of phase with each other.

What amplifier class of operation is the most inefficient but has the least distortion?

Description : What amplifier class of operation is the most inefficient but has the least distortion?

Last Answer : Class A.

What two primary items determine the class of operation of an amplifier?

Description : What two primary items determine the class of operation of an amplifier?

Last Answer : The amount of bias and the amplitude of the input signal

The input and output signals of a JFET amplifier have what phase relationship?

Description : The input and output signals of a JFET amplifier have what phase relationship?

Last Answer : They are 180 degrees out of phase.

What is used to bias a magnetic amplifier so that the control winding remains free to accept control (input) signals?

Description : What is used to bias a magnetic amplifier so that the control winding remains free to accept control (input) signals?

Last Answer : A bias winding and associated circuitry.

What is the purpose of the rectifier in a magnetic amplifier?

Description : What is the purpose of the rectifier in a magnetic amplifier?

Last Answer : The rectifier eliminates hysteresis loss.

At what portion of the magnetization curve should a magnetic amplifier be operated?

Description : At what portion of the magnetization curve should a magnetic amplifier be operated?

Last Answer : . The knee of the curve.

What is the basic principle of a magnetic amplifier?

Description : What is the basic principle of a magnetic amplifier?

Last Answer : change in inductance in a series LR circuit causes a change in true power.

Can a difference amplifier have more than two inputs?

Description : Can a difference amplifier have more than two inputs?

Last Answer : No

What is the difference between a subtractor and a difference amplifier?

Description : What is the difference between a subtractor and a difference amplifier?

Last Answer : . The difference amplifier multiplies the difference between the two inputs by the gain of the circuit while the subtractor merely subtracts one input signal from the other

What is a scaling amplifier?

Description : What is a scaling amplifier?

Last Answer : A summing amplifier that applies a factor to each input signal beforeadding the results.

Can a summing amplifier have more than two inputs?

Description : Can a summing amplifier have more than two inputs?

Last Answer : Yes, a summing amplifier can have as many inputs as desired.

What is the difference between a summing amplifier and an adder circuit?

Description : What is the difference between a summing amplifier and an adder circuit?

Last Answer : The adder simply adds the input signals together while the summing amplifier multiplies the sum of the input signals by the gain of circuit.

If the unity-gain point of the operational amplifier used in question 24 is 500 kilohertz, what is the bandwidth of the circuit?

Description : If the unity-gain point of the operational amplifier used in question 24 is 500 kilohertz, what is the bandwidth of the circuit?

Last Answer : 50 kilohertz (Gain = 10; Gain-Bandwidth Product = 500,000) 500,000(Hz)

In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Description : In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Last Answer : 0 volts.