Which type of flux should be used when soldering electrical wire connections and electronic components? A. Silver flux B. Rosin flux C. Solid flux D. Acid flux

Which type of flux should be used when soldering electrical wire connections and electronic components? A. Silver flux B. Rosin flux C. Solid flux D. Acid flux
by

1 Answer

Answer :

Answer: B
by

Related questions

What type of flux must be used in all electrical and electronic soldering?

Description : What type of flux must be used in all electrical and electronic soldering?

Last Answer : Noncorrosive, nonconductive rosin fluxes.

Why is it a poor practice to use a high wattage soldering iron when soldering or desoldering components on a printed circuit board? A. The circuit board will blister and warp. B. The foil wire bonded to the board may come loosened from the board. C. The circuit board has a low melting temperature. D. The solder is kept to a dull heat dissipating finish.

Description : Why is it a poor practice to use a high wattage soldering iron when soldering or desoldering components on a printed circuit board? A. The circuit board will blister and warp. B. The foil wire bonded ... board has a low melting temperature. D. The solder is kept to a dull heat dissipating finish.

Last Answer : Answer: B

A solid-state circuit is inoperative; the FIRST action that should be taken is to ____________. A. wiggle all the components to check for loose connections B. check all the resistors C. change all transistors D. check the DC supply voltage

Description : A solid-state circuit is inoperative; the FIRST action that should be taken is to ____________. A. wiggle all the components to check for loose connections B. check all the resistors C. change all transistors D. check the DC supply voltage

Last Answer : Answer: D

Acid soldering flux poisoning?

Description : Acid soldering flux poisoning?

Last Answer : DefinitionAcid soldering flux is a chemical used to clean and protect the area (joint) where two pieces of metal come together. Flux poisoning occurs when someone swallows this substance.This is for information only ... Network.Also reviewed by David Zieve, MD, MHA, Medical Director, A.D.A.M., Inc.

When troubleshooting an electronic circuit, a cold solder joint can be located with the aid of an ohmmeter. Once the problem has been located, you should _________________. A. reheat the circuit in an oven to an even temperature and recheck with an ohmmeter B. reheat the connection with a match and recheck with an ohmmeter C. reheat connection with a soldering tool and recheck with an ohmmeter D. do nothing as this is the normal condition

Description : When troubleshooting an electronic circuit, a cold solder joint can be located with the aid of an ohmmeter. Once the problem has been located, you should _________________. A. reheat the circuit in an ... a soldering tool and recheck with an ohmmeter D. do nothing as this is the normal condition

Last Answer : Answer: C

When a solid-state component of an electronic circuit is mounted to a metallic mass, the general purpose of that mass is to ____________. A. prevent vibration damage to delicate components B. prevent mechanical damage to solid-state components C. dissipate stray magnetic currents D. act as a heat sink

Description : When a solid-state component of an electronic circuit is mounted to a metallic mass, the general purpose of that mass is to ____________. A. prevent vibration damage to delicate components B. prevent ... damage to solid-state components C. dissipate stray magnetic currents D. act as a heat sink

Last Answer : Answer: D

The proper way to apply plastic electrical tape to an electric cable splice is to _____________. A. apply tape to the braided cover, but avoid touching it B. wind the tape so that each turn overlaps the turn before it C. apply the tape in one non-overlapping layer only D. heat the tape with a soldering iron for good bonding

Description : The proper way to apply plastic electrical tape to an electric cable splice is to _____________. A. apply tape to the braided cover, but avoid touching it B. wind the tape so that each turn overlaps ... tape in one non-overlapping layer only D. heat the tape with a soldering iron for good bonding

Last Answer : Answer: B

If the bearings of an electrical generator are failing more frequently than expected and the lubricating oil is sludging then you should ______________. A. check the connections to the output leads B. check the bearing insulating block on one end of the unit C. replace the bearing with a sealed roller type D. replace the thrust bearing of the prime mover

Description : If the bearings of an electrical generator are failing more frequently than expected and the lubricating oil is sludging then you should ______________. A. check the connections to the output leads B. ... replace the bearing with a sealed roller type D. replace the thrust bearing of the prime mover

Last Answer : Answer: B

The small circular symbols to which wire '52N57E' is connected at coordinates '57L' and '57P' shown in the illustration represent ___________________. EL-0100 A. relay contact solder points B. wire wrap connections C. terminal board screws D. switch contact terminals

Description : The small circular symbols to which wire '52N57E' is connected at coordinates '57L' and '57P' shown in the illustration represent ___________________. EL-0100 A. relay contact solder points B. wire wrap connections C. terminal board screws D. switch contact terminals

Last Answer : Answer: C

When troubleshooting a console circuit card suspected of being faulty, the last step would be to _______________. A. check the fuses and voltage levels of all power supplies in the console B. clean dust and debris from the card and burnish the sliding connections C. make sure all connections are tight including wire wrappings and push-on types D. substitute a new or repaired spare card and check the operation of the circuit

Description : When troubleshooting a console circuit card suspected of being faulty, the last step would be to _______________. A. check the fuses and voltage levels of all power supplies in the console B. clean dust ... -on types D. substitute a new or repaired spare card and check the operation of the circuit

Last Answer : Answer: D

When troubleshooting a console circuit card which is suspected of being faulty, the first step would be to _____. A. pull the card and measure the value of all resistors B. check for the correct value and polarity of all power connections to the card C. de-energize and pull the card to visually inspect for burned components D. check for continuity of circuit board traces and then the gain of each transistor

Description : When troubleshooting a console circuit card which is suspected of being faulty, the first step would be to _____. A. pull the card and measure the value of all resistors B. check for the ... for burned components D. check for continuity of circuit board traces and then the gain of each transistor

Last Answer : Answer: C

Use of flux during soldering is done to (A) Increase fluidity of solder by lowering its melting temperature (B) Prevent oxide formation (C) Wash away surplus solder (D) Full up the joint gap

Description : Use of flux during soldering is done to (A) Increase fluidity of solder by lowering its melting temperature (B) Prevent oxide formation (C) Wash away surplus solder (D) Full up the joint gap

Last Answer : (B) Prevent oxide formation

What purpose does flux serve in the soldering process?

Description : What purpose does flux serve in the soldering process?

Last Answer : It cleans the metal by removing the oxide layer and prevents further oxidation during the soldering

Flux aids in soldering by removing what from surfaces to be soldered?

Description : Flux aids in soldering by removing what from surfaces to be soldered?

Last Answer : Oxides.

What is the purpose of using flux at the time of soldering?

Description : What is the purpose of using flux at the time of soldering? A. To remove oxidation B. To prevent corrosion C. To promote wet surface D. All of these

Last Answer : What is the purpose of using flux at the time of soldering? A. To remove oxidation B. To prevent corrosion C. To promote wet surface D. All of these

The current from the stator of an alternator is taken out to the external load circuit through (A) slip rings. (B) commutator segments. (C) solid connections. (D) carbon brushes.

Description : The current from the stator of an alternator is taken out to the external load circuit through (A) slip rings. (B) commutator segments. (C) solid connections. (D) carbon brushes.

Last Answer : (C) solid connections.

In actual applications, electrical connections to 'R1-R2' of figure 'A' and to 'R1-R2- R3' of figure 'B' shown in the illustration are made by ______________. EL-0092 A. soldered contacts B. spliced and taped connections C. slip rings and brushes D. solderless crimp-on connectors

Description : In actual applications, electrical connections to 'R1-R2' of figure 'A' and to 'R1-R2- R3' of figure 'B' shown in the illustration are made by ______________. EL-0092 A. soldered contacts B. spliced and taped connections C. slip rings and brushes D. solderless crimp-on connectors

Last Answer : Answer: C

When soldering a printed circuit board component, you should be careful to prevent damage by _________. A. quickly heating the joints, using a high wattage iron B. using the soldering iron tip sparingly C. using only acid cord solder D. applying mechanical pressure to the joints being soldered

Description : When soldering a printed circuit board component, you should be careful to prevent damage by _________. A. quickly heating the joints, using a high wattage iron B. using the soldering iron tip sparingly C. using only acid cord solder D. applying mechanical pressure to the joints being soldered

Last Answer : Answer: B

What is the most common source of heat in electronic soldering?

Description : What is the most common source of heat in electronic soldering?

Last Answer : Conductive-type soldering iron.

The joint for soldering is supported by binding wire made of (A) Mild steel (B) Copper (C) Soft iron (D) Stainless steel

Description : The joint for soldering is supported by binding wire made of (A) Mild steel (B) Copper (C) Soft iron (D) Stainless steel

Last Answer : Option C

What is an advantage of using a resistance soldering iron when soldering wire to a connector?

Description : What is an advantage of using a resistance soldering iron when soldering wire to a connector?

Last Answer : The soldering tips are hot only during the brief period of soldering the connection, thus minimizing the chance of burning the wire insulation or connector inserts.

What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Description : What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Last Answer : Adequate ventilation.

A soldering gun should NOT be used on what components?

Description : A soldering gun should NOT be used on what components?

Last Answer : Electronic components, such as resistors, capacitors, and transistors.

How do you prevent excessive heat buildup on an area of a board when soldering multilead components?

Description : How do you prevent excessive heat buildup on an area of a board when soldering multilead components?

Last Answer : Use a skipping pattern

An electrical connection between the wiring of an electric motor and its metal frame is known as a/an _____________. A. eddy current B. ground C. impedance D. flux leakage

Description : An electrical connection between the wiring of an electric motor and its metal frame is known as a/an _____________. A. eddy current B. ground C. impedance D. flux leakage

Last Answer : Answer: B

In soldering, what alloy changes directly from a solid state to a liquid state?

Description : In soldering, what alloy changes directly from a solid state to a liquid state?

Last Answer : Eutectic.

A common type of protective covering used on electrical conductors is _____________. A. plain paper B. fibrous braid C. silver sheathing D. babbitt sheathing

Description : A common type of protective covering used on electrical conductors is _____________. A. plain paper B. fibrous braid C. silver sheathing D. babbitt sheathing

Last Answer : Answer: B

Maintenance of alkaline batteries should include _________. A. checking the electrolyte weekly using a hydrometer B. replacing the electrolyte every 5 years C. top off with sulfuric acid as needed D. making certain connections are tight and clean

Description : Maintenance of alkaline batteries should include _________. A. checking the electrolyte weekly using a hydrometer B. replacing the electrolyte every 5 years C. top off with sulfuric acid as needed D. making certain connections are tight and clean

Last Answer : Answer: D

Routine maintenance of lead acid batteries should include _____________. A. keeping the terminals clean B. coating cable connections with petroleum jelly C. maintaining a trickle charge D. all of the above

Description : Routine maintenance of lead acid batteries should include _____________. A. keeping the terminals clean B. coating cable connections with petroleum jelly C. maintaining a trickle charge D. all of the above

Last Answer : Answer: D

Rosin after washing the loop

Description : Hi. Because I had the horsehair of the bow already nicely covered with rosin and a bit of dust, I washed them in soapy water. I let them dry for about 5-6 hours. But now they can't be rosin at all ... I ... I have a noose ?? I will be happy for any tips on how to rosin then. Thank you very much :)

Last Answer : Bow The most basic and important principles of the bow are the following: Never tighten the bow too much during the game and always loosen it after the game to release the tension of the ... also stick together with rosin. If you need to replace the horsehair, seek professional help. and šmytec

What is a rosin bag?

Description : What is a rosin bag?

Last Answer : A rosin bag is designed to keep your hands tacky so you have plenty of grip on the ball in Baseball.

The only natural thermoplastic resin, which is a product of animal life is (A) Rosin (B) Shellac (C) Amber (D) Copal

Description : The only natural thermoplastic resin, which is a product of animal life is (A) Rosin (B) Shellac (C) Amber (D) Copal

Last Answer : (B) Shellac

Which of the following is the most important rubber compounding ingredient which is used to improve wearing qualities of both natural rubber & SBR by imparting toughness? (A) Phosphorous (B) Carbon black (C) Pine oil (D) Rosin

Description : Which of the following is the most important rubber compounding ingredient which is used to improve wearing qualities of both natural rubber & SBR by imparting toughness? (A) Phosphorous (B) Carbon black (C) Pine oil (D) Rosin

Last Answer : (B) Carbon black

Which of the following is used as a binding material in soap to improve soap texture? (A) Rosin (B) Borax (C) Benzyl acetate (D) Sodium carbonate

Description : Which of the following is used as a binding material in soap to improve soap texture? (A) Rosin (B) Borax (C) Benzyl acetate (D) Sodium carbonate

Last Answer : (B) Borax

Tall oil obtained as a by-product from the black liquor recovery is (A) A black, sticky & viscous liquid (B) Used in the manufacture of greases, emulsions & soaps (C) Composed mainly of rosin & fatty acids (D) All (A), (B) & (C)

Description : Tall oil obtained as a by-product from the black liquor recovery is (A) A black, sticky & viscous liquid (B) Used in the manufacture of greases, emulsions & soaps (C) Composed mainly of rosin & fatty acids (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Pick out the wrong statement pertaining to the soap manufacture. (A) Transparent soaps are made by cold process (B) Organic pigments are used as colouring materials in the soap manufacture (C) Both laundry as well as toilet soaps are manufactured by hot process (D) Colourless rosin is used in the manufacture of laundry soaps

Description : Pick out the wrong statement pertaining to the soap manufacture. (A) Transparent soaps are made by cold process (B) Organic pigments are used as colouring materials in the soap manufacture (C) ... soaps are manufactured by hot process (D) Colourless rosin is used in the manufacture of laundry soaps

Last Answer : (A) Transparent soaps are made by cold process

Rosin soap is added during paper manufacture to (A) Impart adhesive properties (B) Improve opacity (C) Impart resistance to penetration by liquids (D) None of these

Description : Rosin soap is added during paper manufacture to (A) Impart adhesive properties (B) Improve opacity (C) Impart resistance to penetration by liquids (D) None of these

Last Answer : (C) Impart resistance to penetration by liquids

Before servicing the device indicated as 'A' in panels #1 and #3 of the illustration, the device labeled 'CT' must __________. EL-0003 A. have the disconnected leads taped to prevent short circuiting. B. only be connected to multimeter on the ammeter setting C. be short circuited D. have one lead grounded to discharge static electricity for the prevention of damage to electronic components

Description : Before servicing the device indicated as 'A' in panels #1 and #3 of the illustration, the device labeled 'CT' must __________. EL-0003 A. have the disconnected leads taped to prevent ... D. have one lead grounded to discharge static electricity for the prevention of damage to electronic components

Last Answer : Answer: C

Which of the following statements describes the significance of ambient temperature in relation to the service life of electronic components? A. Ambient temperature should be as high as possible to drive off moisture. B. Increased ambient temperature decreases the service life of electronic components. C. Ambient temperature is not significant as long as the relative humidity is kept low. D. A reduced ambient temperature causes a corresponding reduced service life.

Description : Which of the following statements describes the significance of ambient temperature in relation to the service life of electronic components? A. Ambient temperature should be as high as possible to drive ... is kept low. D. A reduced ambient temperature causes a corresponding reduced service life.

Last Answer : Answer: B

When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only and a low resistance meter for DC measurements C. whenever a low impedance meter is not available, regardless of the components being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Description : When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only ... being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Last Answer : Answer: D

Motor controllers are seldom troubled by grounds because ________________. A. cabinet heaters always keep internal components dry B. special insulation is used on wire for vital circuits C. shock mounts on controller panels greatly reduce vibration D. contactors and relays are mounted on nonconducting panels

Description : Motor controllers are seldom troubled by grounds because ________________. A. cabinet heaters always keep internal components dry B. special insulation is used on wire for vital circuits C. ... on controller panels greatly reduce vibration D. contactors and relays are mounted on nonconducting panels

Last Answer : Answer: D

Tightly knit metal braid wire can be used with a printed circuit board when ___________. A. conductor flexibility is required B. desoldering components in the circuit C. electrically produced magnetic fluxes would cause inaccuracies in adjacent components D. reactance in the circuit must be kept to a minimum

Description : Tightly knit metal braid wire can be used with a printed circuit board when ___________. A. conductor flexibility is required B. desoldering components in the circuit C. electrically produced magnetic ... cause inaccuracies in adjacent components D. reactance in the circuit must be kept to a minimum

Last Answer : Answer: B

If a delicate component must be soldered into a circuit, the component may be protected from the heat of the soldering process by _____________. A. operating the soldering gun not more than 60 seconds at a time B. using a thermal shunt C. pre-oxidizing the leads to be soldered D. coating the leads to be soldered with a light oil film

Description : If a delicate component must be soldered into a circuit, the component may be protected from the heat of the soldering process by _____________. A. operating the soldering gun not more than 60 seconds at ... oxidizing the leads to be soldered D. coating the leads to be soldered with a light oil film

Last Answer : Answer: B

Which of the procedures listed could result in damaging a transistor beyond repair? A. Applying incorrect polarity to the collector circuit. B. Applying excessive voltage to the input circuit. C. Careless soldering which would overheat the transistor. D. All of the above.

Description : Which of the procedures listed could result in damaging a transistor beyond repair? A. Applying incorrect polarity to the collector circuit. B. Applying excessive voltage to the input circuit. C. Careless soldering which would overheat the transistor. D. All of the above.

Last Answer : Answer: D

What is soldering and what is brazing?

Description : What is soldering and what is brazing?

Last Answer : Soldering is the process of joining two metals with an alloy whose melting point is less that of the materials to be soldered. Soldering at high temperature using brass as solder is called brazing or hard ... soft solder) is tin 60% and lead 40%. Its melting point is 190°C and is widely used.  

Which of the following materials is a good electrical insulator? A. wood B. silver C. copper D. gold

Description : Which of the following materials is a good electrical insulator? A. wood B. silver C. copper D. gold

Last Answer : Answer: A

Which solid AWG wire size has the smallest physical cross-sectional area? A. 12 B. 14 C. 16 D. 18

Description : Which solid AWG wire size has the smallest physical cross-sectional area? A. 12 B. 14 C. 16 D. 18

Last Answer : Answer: D

Before any work on electrical or electronic equipment is performed, which of the following precautions should be carried out? A. De-energize the applicable switchboard bus. B. Bypass the interlocks. C. Secure and tag the supply circuit breaker in the open position. D. Station a man at the circuit supply switch.

Description : Before any work on electrical or electronic equipment is performed, which of the following precautions should be carried out? A. De-energize the applicable switchboard bus. B. Bypass the interlocks. C. ... supply circuit breaker in the open position. D. Station a man at the circuit supply switch.

Last Answer : Answer: C

What is represented by the solid dots within components 'B' and 'C' of the diagram shown in the illustration? (See illustration EL-0081) EL-0081 A. The fact that these parts are subject to wear and replacement. B. An indication that they are for 110 volt AC operation only. C. The particular components contain a gas such as neon or argon. D. All of the above.

Description : What is represented by the solid dots within components 'B' and 'C' of the diagram shown in the illustration? (See illustration EL-0081) EL-0081 A. The fact that these parts are subject to wear and ... only. C. The particular components contain a gas such as neon or argon. D. All of the above.

Last Answer : Answer: C