What is the advantage of designing a limited bandwidth into a servo amplifier?

What is the advantage of designing a limited bandwidth  into a servo amplifier?
by

1 Answer

Answer :

Unwanted noise-generated frequencies are rejected
by

Related questions

What is the advantage of using a closed-servo loop to control load velocity?

Description : What is the advantage of using a closed-servo loop to control load velocity?

Last Answer : The closed-servo loop can regulate load speed under changing conditions.

The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency end and bypass capacitors at the low frequency end C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and D) shunt capacitors at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Description : The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency ... at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Last Answer : C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and

What is the bandwidth of an amplifier?

Description : What is the bandwidth of an amplifier?

Last Answer : The difference between the upper and lower frequency limits of an amplifier.

If the unity-gain point of the operational amplifier used in question 24 is 500 kilohertz, what is the bandwidth of the circuit?

Description : If the unity-gain point of the operational amplifier used in question 24 is 500 kilohertz, what is the bandwidth of the circuit?

Last Answer : 50 kilohertz (Gain = 10; Gain-Bandwidth Product = 500,000) 500,000(Hz)

As shown in the illustration, the circuit which 'shapes' the linear output of the thrust lever so that the steady-state ship speed is linear with respect to that lever's setting is the _____________. EL-0095 A. 'pitch controller' B. 'error amplifier' C. 'function generator' D. 'servo amplifier'

Description : As shown in the illustration, the circuit which 'shapes' the linear output of the thrust lever so that the steady-state ship speed is linear with respect to that lever's setting is the _____________. EL-0095 A. 'pitch controller' B. 'error amplifier' C. 'function generator' D. 'servo amplifier'

Last Answer : Answer: C

What is the primary advantage of power-amplifier transmitters over keyed-oscillator transmitters?

Description : What is the primary advantage of power-amplifier transmitters over keyed-oscillator transmitters?

Last Answer : Frequency stability.

What is the primary advantage of power-amplifier transmitters over keyed-oscillator transmitters?

Description : What is the primary advantage of power-amplifier transmitters over keyed-oscillator transmitters?

Last Answer : Frequency stability.

What is the purpose of a synchronizing network in a servo system?

Description : What is the purpose of a synchronizing network in a servo system?

Last Answer : To switch control of the amplifier between either the coarse signal and the fine error signal.

What is the purpose of a demodulator in a servo system?

Description : What is the purpose of a demodulator in a servo system?

Last Answer : To convert an ac error signal into a dc error signal.

What is the purpose of a modulator in a servo system?

Description : What is the purpose of a modulator in a servo system?

Last Answer : To convert a dc error signal into an ac error signal.

In a properly designed servo system that has an oscillating input (order), what should be the response of the load?

Description : In a properly designed servo system that has an oscillating input (order), what should be the response of the load?

Last Answer : It should oscillate.

Why is damping needed in a practical servo system?

Description : Why is damping needed in a practical servo system?

Last Answer : . To minimize overshoot and/or oscillations.

If a position servo system does not respond to small changes of the input, is the system overdamped or underdamped?

Description : If a position servo system does not respond to small changes of the input, is the system overdamped or underdamped?

Last Answer : Overdamped.

If a position servo system tends to oscillate whenever a new position is selected, is the system overdamped or underdamped?

Description : If a position servo system tends to oscillate whenever a new position is selected, is the system overdamped or underdamped?

Last Answer : Underdamped

In a typical velocity servo block diagram what device is placed in the feedback loop that is not present in the position servo?

Description : In a typical velocity servo block diagram what device is placed in the feedback loop that is not present in the position servo?

Last Answer : Tachometer.

What term is used for a series of overshoots in a servo system?

Description : What term is used for a series of overshoots in a servo system?

Last Answer : Hunting.

The output of the sum point must contain information that controls what two factors of load movement in a position servo?

Description : The output of the sum point must contain information that controls what two factors of load movement in a position servo?

Last Answer : Amount and direction of rotation.

What are the three relatively common classifications of servo systems by function?

Description : What are the three relatively common classifications of servo systems by function?

Last Answer : Classifications in accordance with position, velocity, and acceleration functions.

What is a servo?

Description : What is a servo?

Last Answer : A system in which the precise movement of a large load is controlled by a relatively weak control signal.

What are the two functions of the servo motor in the system

Description : What are the two functions of the servo motor in the system

Last Answer : To move the load and provide feedback data to the error detector.

When designing vacuum-tube circuits, what characteristics of tubes must be taken into consideration?

Description : When designing vacuum-tube circuits, what characteristics of tubes must be taken into consideration?

Last Answer : Differences in performance of tubes of the same type

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to 5kHz, its gain remaining constant, what does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Description : The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to ... does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Last Answer : A. 0.5 mV

What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Description : What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Last Answer : D. IF amplifier

Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Description : Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Last Answer : A) Wave traps in each stage

Define gain and bandwidth of an amplifier.

Description : Define gain and bandwidth of an amplifier.

Last Answer : Bandwidth  The range of frequency over which the voltage gain is equal to or greater than 70.7% of its maximum value Gain: The ratio of output parameter (voltage/ current /power) to the input parameter (voltage/ current /power) of an amplifier is known as gain. It is denoted by a letter A

The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is

Description : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

Last Answer : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

If three amplifiers having the same bandwidth are cascaded, the bandwidth of the resulting amplifier will be

Description : If three amplifiers having the same bandwidth are cascaded, the bandwidth of the resulting amplifier will be (a) Better than that of each stage (b) Worse than that of each stage (c) Same as that of each stage (d) None of the above 

Last Answer : If three amplifiers having the same bandwidth are cascaded, the bandwidth of the resulting amplifier will be Worse than that of each stage

The bandwidth of a fiber is limited by ∙ a. Mode ∙ b. Wavelength ∙ c. Dispersion ∙ d. Frequency

Description : The bandwidth of a fiber is limited by ∙ a. Mode ∙ b. Wavelength ∙ c. Dispersion ∙ d. Frequency

Last Answer : c. Dispersion

The large signal bandwidth of an opamp is limited by its:

Description : The large signal bandwidth of an opamp is limited by its:  (1) Loop gain (2) Slew rate (3) Output impedance (4) Input frequency

Last Answer : The large signal bandwidth of an opamp is limited by its: Slew rate.

What determines the frequency, bandwidth, and power handling capability of a waveguide probe?

Description : What determines the frequency, bandwidth, and power handling capability of a waveguide probe?

Last Answer : Size and shape

Receiver bandwidth is defined as those frequencies spread between what two points of the receiver response curve?

Description : Receiver bandwidth is defined as those frequencies spread between what two points of the receiver response curve?

Last Answer : Half-power points.

LEDs operating at 850 nm provide sufficient optical power for short-distance, low-bandwidth multimode systems. List three conditions that prevent the use of LEDs in longer distance, higher bandwidth multimode systems.

Description : LEDs operating at 850 nm provide sufficient optical power for short-distance, low-bandwidth multimode systems. List three conditions that prevent the use of LEDs in longer distance, higher bandwidth multimode systems.

Last Answer : Multimode fiber dispersion, the relatively high fiber attenuation, and the LED's relatively low optical output power.

While coupled power and bending loss favor a high D, which Dvalue, smaller or larger, improves fiber bandwidth?

Description : While coupled power and bending loss favor a high D, which Dvalue, smaller or larger, improves fiber bandwidth?

Last Answer : Smaller.

Light travels faster in a material with a lower refractive index. Therefore, light rays that travel a longer distance in a lower refractive index travel at a greater average velocity. What effect does this have on multimode graded-index fiber modal dispersion and bandwidth?

Description : Light travels faster in a material with a lower refractive index. Therefore, light rays that travel a longer distance in a lower refractive index travel at a greater average velocity. What effect does this have on multimode graded-index fiber modal dispersion and bandwidth?

Last Answer : Decreases the time difference between light rays, which reduces modal dispersion and increases fiber bandwidth.

Which preamplifier design (high-impedance or transimpedance) provides improvements in bandwidth and greater dynamic range with some degradation in sensitivity from an increase in noise?

Description : Which preamplifier design (high-impedance or transimpedance) provides improvements in bandwidth and greater dynamic range with some degradation in sensitivity from an increase in noise?

Last Answer : Transimpedance.

In a multicavity klystron, tuning all the cavities to the same frequency has what effect on the bandwidth of the tube?

Description : In a multicavity klystron, tuning all the cavities to the same frequency has what effect on the bandwidth of the tube?

Last Answer : The bandwidth decreases.

Most record and reproduce heads are in one of what three bandwidth categories?

Description : Most record and reproduce heads are in one of what three bandwidth categories?

Last Answer : a. Narrowband—100 Hz to 100 kHz. b. Intermediate band—100 Hz to 500 kHz. c. Wideband—400 Hz to 2 mHz.

Modal dispersion affects the bandwidth of multimode systems. It is essential to adjust what three fiber properties to maximize system bandwidth?

Description : Modal dispersion affects the bandwidth of multimode systems. It is essential to adjust what three fiber properties to maximize system bandwidth?

Last Answer : Core diameter, NA, and index profile properties.

What category of digital tape recorder is used to record special signals with a bandwidth of less than 500 kHz?

Description : What category of digital tape recorder is used to record special signals with a bandwidth of less than 500 kHz?

Last Answer : Instrumentation digital tape recorders.

What two values may be used to determine the bandwidth of an fm wave?

Description : What two values may be used to determine the bandwidth of an fm wave?

Last Answer : The number of significant sidebands and the modulating frequency.

What determines the bandwidth of an AM transmission?

Description : What determines the bandwidth of an AM transmission?

Last Answer : The highest modulating frequency.

What is the primary advantage of DSBSC in AM? A. Reduce bandwidth over standard AM B. All of these C. It is simpler to transmit and receive than the standard AM D. No transmitter power is wasted in the carrier

Description : What is the primary advantage of DSBSC in AM? A. Reduce bandwidth over standard AM B. All of these C. It is simpler to transmit and receive than the standard AM D. No transmitter power is wasted in the carrier

Last Answer : D. No transmitter power is wasted in the carrier

If C4 were removed from the circuit, what would happen to the output of the amplifier?

Description : If C4 were removed from the circuit, what would happen to the output of the amplifier?

Last Answer : The output would decrease. (C4 decouples R2 preventing degenerative feedback from R2.)

What components form the input-signal-developing impedance for the amplifier?

Description : What components form the input-signal-developing impedance for the amplifier?

Last Answer : C2 and the secondary of T1.

What two methods are used to compensate for the problems that cause low gain in an rf amplifier?

Description : What two methods are used to compensate for the problems that cause low gain in an rf amplifier?

Last Answer : . RF transformers are used and the transistor is neutralized.

What problem is caused in an rf amplifier by a loosely coupled transformer?

Description : What problem is caused in an rf amplifier by a loosely coupled transformer?

Last Answer : A too-narrow bandpass.

What is the most common form of coupling for an rf amplifier?

Description : What is the most common form of coupling for an rf amplifier?

Last Answer : Transformer coupling.