What is the purpose of a synchronizing network in a servo system?

What is the purpose of a synchronizing network in a servo  system?
by

1 Answer

Answer :

To switch control of the amplifier between either the coarse  signal and the fine error signal.
by

Related questions

What is the purpose of a demodulator in a servo system?

Description : What is the purpose of a demodulator in a servo system?

Last Answer : To convert an ac error signal into a dc error signal.

What is the purpose of a modulator in a servo system?

Description : What is the purpose of a modulator in a servo system?

Last Answer : To convert a dc error signal into an ac error signal.

In a properly designed servo system that has an oscillating input (order), what should be the response of the load?

Description : In a properly designed servo system that has an oscillating input (order), what should be the response of the load?

Last Answer : It should oscillate.

Why is damping needed in a practical servo system?

Description : Why is damping needed in a practical servo system?

Last Answer : . To minimize overshoot and/or oscillations.

If a position servo system does not respond to small changes of the input, is the system overdamped or underdamped?

Description : If a position servo system does not respond to small changes of the input, is the system overdamped or underdamped?

Last Answer : Overdamped.

If a position servo system tends to oscillate whenever a new position is selected, is the system overdamped or underdamped?

Description : If a position servo system tends to oscillate whenever a new position is selected, is the system overdamped or underdamped?

Last Answer : Underdamped

What term is used for a series of overshoots in a servo system?

Description : What term is used for a series of overshoots in a servo system?

Last Answer : Hunting.

What are the two functions of the servo motor in the system

Description : What are the two functions of the servo motor in the system

Last Answer : To move the load and provide feedback data to the error detector.

What is the advantage of designing a limited bandwidth into a servo amplifier?

Description : What is the advantage of designing a limited bandwidth into a servo amplifier?

Last Answer : Unwanted noise-generated frequencies are rejected

What is the advantage of using a closed-servo loop to control load velocity?

Description : What is the advantage of using a closed-servo loop to control load velocity?

Last Answer : The closed-servo loop can regulate load speed under changing conditions.

In a typical velocity servo block diagram what device is placed in the feedback loop that is not present in the position servo?

Description : In a typical velocity servo block diagram what device is placed in the feedback loop that is not present in the position servo?

Last Answer : Tachometer.

The output of the sum point must contain information that controls what two factors of load movement in a position servo?

Description : The output of the sum point must contain information that controls what two factors of load movement in a position servo?

Last Answer : Amount and direction of rotation.

What are the three relatively common classifications of servo systems by function?

Description : What are the three relatively common classifications of servo systems by function?

Last Answer : Classifications in accordance with position, velocity, and acceleration functions.

What is a servo?

Description : What is a servo?

Last Answer : A system in which the precise movement of a large load is controlled by a relatively weak control signal.

What is the purpose of a frequency-determining network in an rf amplifier?

Description : What is the purpose of a frequency-determining network in an rf amplifier?

Last Answer : To provide maximum impedance at the desired frequency.

what is the purpose of the series-parallel network R 3, R 4, and R5?

Description : what is the purpose of the series-parallel network R 3, R 4, and R5?

Last Answer : The series-parallel network drops the remaining source voltage and is used to take the place of a single resistor (75 ohms) when the required ohmic value is not available in a single resistor.

What is the purpose of an amplifier-coupling network?

Description : What is the purpose of an amplifier-coupling network?

Last Answer : To transfer energy (a signal) from one stage to another.

A diesel driven emergency generator is prevented from being paralleled with the ship's service generators by __________. A. an electrical interlock system B. an automatic paralleling trip switch C. the synchronizing oscilloscope D. the reverse current relay

Description : A diesel driven emergency generator is prevented from being paralleled with the ship's service generators by __________. A. an electrical interlock system B. an automatic paralleling trip switch C. the synchronizing oscilloscope D. the reverse current relay

Last Answer : Answer: A

Synchronizing iCal to Google Calendar?

Description : Synchronizing iCal to Google Calendar?

Last Answer : get on http://Digg.com they have an article talking about how you can do it. Just search iCal.

Attempting to parallel an AC generator which is out of phase with the bus will result in which of the following problems? A. The breaker should trip. B. The KVA will decrease. C. The synchronizing lamps will burn out. D. The power factor will be unitized.

Description : Attempting to parallel an AC generator which is out of phase with the bus will result in which of the following problems? A. The breaker should trip. B. The KVA will decrease. C. The synchronizing lamps will burn out. D. The power factor will be unitized.

Last Answer : Answer: A

A current-carrying conductor makes accidental contact with a wiring conduit. This will be indicated by a _____________. A. low switchboard wattmeter reading B. high switchboard wattmeter reading C. darkened switchboard ground detecting lamp D. darkened switchboard synchronizing lamps

Description : A current-carrying conductor makes accidental contact with a wiring conduit. This will be indicated by a _____________. A. low switchboard wattmeter reading B. high switchboard wattmeter reading C. darkened switchboard ground detecting lamp D. darkened switchboard synchronizing lamps

Last Answer : Answer: C

When paralleling two alternators, the synchronizing lamps remain lit as the synchroscope pointer approaches the 0°. This indicates the _____________. A. incoming alternator is running too fast B. alternator voltages are 180 degrees apart C. synchroscope is defective or broken D. alternator power factors are in phase

Description : When paralleling two alternators, the synchronizing lamps remain lit as the synchroscope pointer approaches the 0°. This indicates the _____________. A. incoming alternator is running too fast B. alternator ... apart C. synchroscope is defective or broken D. alternator power factors are in phase

Last Answer : Answer: C

When paralleling two alternators the synchronizing lamps grow dim and are totally darkened as the synchroscope pointer approaches the 0° position. This indicates the ____________. A. alternator voltages are 180° apart B. incoming alternator is running too fast C. incoming alternator is in phase with the bus voltage D. synchroscope pointer is defective or broken

Description : When paralleling two alternators the synchronizing lamps grow dim and are totally darkened as the synchroscope pointer approaches the 0° position. This indicates the ____________. A. alternator voltages ... alternator is in phase with the bus voltage D. synchroscope pointer is defective or broken

Last Answer : Answer: C

When paralleling two alternators using three synchronizing lamps, the flickering of all three lamps becomes progressively slower and slower. This means the ______________. A. frequency of the incoming generator is approaching that of the bus B. frequency of the incoming alternator is less than that of the bus C. phase rotation of the incoming alternators is opposite to that of the bus D. terminal voltage of the incoming alternator is approaching that of the bus

Description : When paralleling two alternators using three synchronizing lamps, the flickering of all three lamps becomes progressively slower and slower. This means the ______________. A. frequency of the incoming ... the bus D. terminal voltage of the incoming alternator is approaching that of the bus

Last Answer : Answer: A

An AC generator panel is fitted with both synchronizing lamps and a synchroscope. When the synchroscope pointer reaches the noon position, one synchronizing light is bright and the other is dark. This means _____________. A. there is a ground on the phase with the dark lamp B. the phase sequence is incorrect C. the phase sequence is correct D. the generator breaker may be closed

Description : An AC generator panel is fitted with both synchronizing lamps and a synchroscope. When the synchroscope pointer reaches the noon position, one synchronizing light is bright and the other is dark. This ... sequence is incorrect C. the phase sequence is correct D. the generator breaker may be closed

Last Answer : Answer: B

You are paralleling two alternators. The synchronizing lamps grow dim and are totally darkened as the synchroscope pointer approaches the 0° position. This indicates that the ____________. A. alternator voltages are 180° apart B. circuit breaker can be closed C. incoming alternator is running too slowly D. synchroscope is defective or broken

Description : You are paralleling two alternators. The synchronizing lamps grow dim and are totally darkened as the synchroscope pointer approaches the 0° position. This indicates that the ____________. A. alternator ... be closed C. incoming alternator is running too slowly D. synchroscope is defective or broken

Last Answer : Answer: B

While paralleling two (2) AC generators using synchronizing lamps only, both lamps will go dark when the generators are ____________. A. running at the same speed B. grounded C. of the same polarity D. in phase

Description : While paralleling two (2) AC generators using synchronizing lamps only, both lamps will go dark when the generators are ____________. A. running at the same speed B. grounded C. of the same polarity D. in phase

Last Answer : Answer: D

The voltage of an operating AC turbogenerator is raised or lowered by adjusting the _____________. A. exciter generator governor controls B. synchronizing switch C. phase sequence switch D. generator field exciter

Description : The voltage of an operating AC turbogenerator is raised or lowered by adjusting the _____________. A. exciter generator governor controls B. synchronizing switch C. phase sequence switch D. generator field exciter

Last Answer : Answer: D

As shown in the illustrations, feedback or rudder angle repeatback is used by the steering stand in which operational modes? EL-0097 A. Gyro-compass and hand steering only B. Hand steering and non-followup only C. Non-followup and gyro-compass only D. Gyro-compass and synchronizing only

Description : As shown in the illustrations, feedback or rudder angle repeatback is used by the steering stand in which operational modes? EL-0097 A. Gyro-compass and hand steering only B. Hand steering and non-followup only C. Non-followup and gyro-compass only D. Gyro-compass and synchronizing only

Last Answer : Answer: A

How synchronoscope is used for synchronizing Alternators?

Description : How synchronoscope is used for synchronizing Alternators?

Last Answer : Synchronoscope can be used for permanently connected Alternators where the correctness of phase sequence is already checked by other means. The rotation of pointer is proportional to the difference in ... alternator is running slow. If the difference in frequency is large the pointer will oscillate

What are the advantages and disadvantages of three dark lamps method of synchronizing?

Description : What are the advantages and disadvantages of three dark lamps method of synchronizing?

Last Answer : Advantages: · The synchronous switch using lamps is inexpensive · Checking for correctness of the phase sequence can be obtained in a simple manner which is essential especially when the Alternator ... The frequency of the incoming Alternator in relation to the bus-bar frequency is not available.

What is synchronizing?

Description : What is synchronizing?

Last Answer : The operation of connecting an alternator in parallel with another alternator or with common bus bars is known as synchronizing.

How would one squeeze more channels of communication into TDM frames of standard length? A. Shorten the time delay for each channel B. Raise the amplitude C. Add modulators D. Remove the synchronizing pulses

Description : How would one squeeze more channels of communication into TDM frames of standard length? A. Shorten the time delay for each channel B. Raise the amplitude C. Add modulators D. Remove the synchronizing pulses

Last Answer : A. Shorten the time delay for each channel

What are the settings provided in synchronizing scheme (SKE Relay)?

Description : What are the settings provided in synchronizing scheme (SKE Relay)?

Last Answer : Voltage – V1- V2 = 10% Frequency – t = 0.05 Sec (2.5 Hz) % Slip – 0.45 Phase angle difference - 20°. 

Why synchronizing scheme has been adopted? What are interlocks provided?

Description : Why synchronizing scheme has been adopted? What are interlocks provided?  

Last Answer : To check running and incoming buses, which are going to be interconnected are in synchronism with each other. Interlocks 1. Synch selector. 2. Only one breaker can operate at a time. 3. ... will bypass this synch contact). Bypass facility is provided to close the breaker on dead bus only. 

What are the methods of synchronizing?

Description : What are the methods of synchronizing?

Last Answer : a. Lamp method. Dark lamp method and bright lamp method. b. Synchroscope method.

The process of converting analog signals into digital signals so they can be processed by a receiving computer is referred to as: a. modulation b. demodulation c. synchronizing d. digitising

Description : The process of converting analog signals into digital signals so they can be processed by a receiving computer is referred to as: a. modulation b. demodulation c. synchronizing d. digitising

Last Answer : digitising

The process of converting analog signals into digital signals so they can be processed by a receiving computer is referred to as a. modulation b. demodulation c. synchronizing d. Digitizing

Description : The process of converting analog signals into digital signals so they can be processed by a receiving computer is referred to as a. modulation b. demodulation c. synchronizing d. Digitizing

Last Answer : b. demodulation

After a black out the emergency generator comes on; On restoring the main supply we are closing the circuit breaker of the main generator without bothering about synchronizing. How is this possible?

Description : After a black out the emergency generator comes on; On restoring the main supply we are closing the circuit breaker of the main generator without bothering about synchronizing. How is this possible?

Last Answer : There is a power link connection breaker between the main generator and the emergency generator. During black out, this breaker trips. The emergency generator starts and its breaker closes and feeds only ... , there is no paralleling between main and emergency generator. Ask E/O for more details.

What is dark lamp and bright lamp method for synchronizing? How is the connection made?

Description : What is dark lamp and bright lamp method for synchronizing? How is the connection made?

Last Answer : Formerly, three light bulbs were connected between the generator terminals and the system terminals. As the generator speed changes, the lights will rise and fall in intensity at a rate proportional to ... to the system may be closed and the generator will then stay in synchronism with the system.

____________ carries signalling and synchronizing commands. a) Traffic channels b) Control channels c) Signalling channels d) Forward channels

Description : ____________ carries signalling and synchronizing commands. a) Traffic channels b) Control channels c) Signalling channels d) Forward channels

Last Answer : b) Control channels

why equalizing pulses are needed. Draw the vertical synchronizing pulse structure.

Description : why equalizing pulses are needed. Draw the vertical synchronizing pulse structure.

Last Answer : The ½ line difference just prior to the start of serrated vertical pulse does not affect the horizontal deflection synchronization but it does affect the vertical synchronization and the interlaced scanning. The ... the vertical sync pulse to occur at the correct time after every field.

As shown in the illustration, a 'pitch cutback' feature is incorporated in the system. This circuit reduces pitch amount to prevent engine overload when it senses ____________. EL-0095 A. pitch error of any magnitude B. wrong direction of the 'pitch servo' C. excessive propeller speed or fuel to either engine D. only one engine on the line

Description : As shown in the illustration, a 'pitch cutback' feature is incorporated in the system. This circuit reduces pitch amount to prevent engine overload when it senses ____________. EL-0095 A. pitch error of ... servo' C. excessive propeller speed or fuel to either engine D. only one engine on the line

Last Answer : Answer: C

Define servo system. Draw the block diagram of DC Servo System.

Description : Define servo system. Draw the block diagram of DC Servo System.

Last Answer : Definition: Servo system is defined as automatic feedback control system working on error signals giving the output as mechanical position, velocity or acceleration.  1) The servo system consists of error ... , DC motor, DC gear system and the DC load whose position is to be changed. 

Explain energy conservation method in lighting system by using installation of separate transformer / servo stabilizer.

Description : Explain energy conservation method in lighting system by using installation of separate transformer / servo stabilizer.

Last Answer : Energy conservation techniques by installation of separate transformer / servo stabilizer: The luminous efficiency of lamps depends upon the voltage applied across the terminals. It gives its best ... the voltage constant in that installation for giving best luminous efficiency of lamps.

For a 2nd order servo system, the damping ratio δ = 0.5456 and undamped natural frequency is

Description : For a 2nd order servo system, the damping ratio δ = 0.5456 and undamped natural frequency is ωn = 31.6 rad/sec. The percent overshoot is  (a) 7.07 (b) 10.2 (c) 14.10 (d) 21.21

Last Answer : For a 2nd order servo system, the damping ratio δ = 0.5456 and undamped natural frequency is ωn = 31.6 rad/sec. The percent overshoot is 14.10

What is a servo motor in Arduino?

Description : What is a servo motor in Arduino?

Last Answer : A servo motor in Arduino is a type of motor that can be used for precise control of position, speed, and acceleration and is commonly used in robotics and automation.

What is a servo motor in Arduino?

Description : What is a servo motor in Arduino?

Last Answer : A servo motor in Arduino is a type of motor that is used for precise control of position, speed, and acceleration.