Description : As shown in the illustration, if 'R1' and 'R2' have unequal values, the ____________. EL-0019 A. voltage drop across 'R1' will not be equal to the voltage drop across 'R2' B. current flow ... energy dissipated in 'R2' D. current flow through 'R1' will differ from the current flow through 'R2'
Last Answer : Answer: D
Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts
Last Answer : Answer: C
Description : What would be the voltage drop across the parallel branches of the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts
Last Answer : Answer: B
Description : A, when there is an increase in the input voltage, the forward bias of Q1 increases/decreases (which one).
Last Answer : Increases.
Description : The component labeled 'CR1' in the circuit shown in the illustration __________________. EL-0085 A. varies its anode/cathode polarity depending on 'RL' current B. rectifies the varying voltage from the ... reactance to smooth ripple D. establishes a constant reference voltage for the base of 'Q1'
Description : Besides eliminating the emitter-base battery, what other advantages can different biasing methods offer?
Last Answer : Compensation for slight variations in transistor characteristics and changes in transistor conduction because of temperature variations.
Description : how is (a) the current through R2 and (b) the voltage drop across R2 computed?
Last Answer : (a) By adding the bleeder current (IR1) and the current through load 1(b) By subtracting the voltage of load 1 from the voltage of load 2.
Description : If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?
Last Answer : E1 = 80 volts. E2 = 240 volts. E3 = 320 volts
Description : What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?
Last Answer : Zero.
Description : What is the Voltage drop of R1 If V 10 Volts R1 500 Ohms and R2 1500 Ohms?
Last Answer : You need to mention whether the resistors are in series or parallel to get the right answer
Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?
Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.
Description : A series circuit consisting of three resistors has a current of 3 amps. If R1 = 20 ohms, R2= 60 ohms, and R 3 = 80 ohms, what is the (a) total resistance and (b) source voltage of the circuit?
Last Answer : (a) 160 ohms. (b) 480 ohms
Description : The common-emitter transistor circuit can amplify a small current signal because a small change in the signal current produces one of the following. Does the change in signal produce a large change in the: w) emitter-base voltage x) base current y) collector current z) collector voltage
Last Answer : ANSWER: Y -- COLLECTOR CURRENT
Description : In the illustration, 12 volts is applied to the circuit where the resistance of R1 is 10 ohms and R2 is 10 ohms. what is the voltage across R2? EL-0036 A. 1.2 volts B. 2 volts C. 6 volts D. 12 volts
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the voltage measured across R1 EL-0036 A. 11.86 volts B. .131 volts C. 12 volts D. .673 volts
Description : In the illustrated circuit, what is the resistance across R2 if the battery voltage is 32 VDC, the resistance of R1 is 1.2 kohms and the current through R2 is 18.82 milliamps? EL-0036 A. 500 ohms B. 1,200 ohms C. 10 ohms D. The answer can not be found with the information given.
Last Answer : Answer: A
Description : In the illustrated circuit, what is the voltage measured across R1 if the battery is 24 volts, the resistance of R1 is 34 ohms, and the resistance of R2 is 126 ohms? EL-0036 A. 24 volts B. 18.9 volts C. 5.1 volts D. 150 millivolts
Description : The illustrated circuit is a wheatstone bridge. If the meter 'G' reads 0 with the switch closed then ________. EL-0024 A. the current through R1 - R2 is equal to the current through R3 - Rx B. the voltage ... of E C. the resistance of Rx is equal to the resistance of R2 D. all the above are true
Description : What is the voltage across 'R3' of the illustrated circuit if the supply is 24 volts and the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 volts B. 6 volts C. 8 volts D. 10 volts
Description : What is the voltage across 'R2' of the illustrated circuit if the supply is 24 volts and the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 volts B. 6 volts C. 8 volts D. 10 volts
Description : What is the voltage across 'R1' of the illustrated circuit if the supply is 24 volts and resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 volts B. 6 volts C. 8 volts D. 10 volts
Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1 = 2.1 ohms RT= 2.1 + 7.8 = 9.9 ohms IT = V/R = 24/9.9 = 2.4 A Veq= R I = 2.1 2 ... 7.8 = 12.096 w = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]
Description : . What components form the load for Q1?
Last Answer : C5 and the primary of T2.
Description : What component(s) is/are used for high-frequency compensation for Q1?
Last Answer : L1, L2, and R5.
Description : Which quantity (voltage or current) determines the intensity of an electrical shock?
Last Answer : Current.
Description : What determines the amount of slip in an induction motor?
Last Answer : Load.
Description : The percentage increase in power consumption of a compressor with suction side air filter and with the pressure drop across the filter of 200 mmWc is ____ a) 1.0% b) 3% c) 2.4% d) 1.6%
Last Answer : d) 1.6%
Description : What is the input current in the common-emitter circuit?
Last Answer : Base current (IB).
Description : What is the polarity of the first alternation of the tank circuit in an emitter-loaded npn pulsed oscillator?
Last Answer : Negative
Description : How is the output signal developed in the common-emitter detector?
Last Answer : By the collector current flow through R4.
Description : Which junction of the transistor in the common-emitter detector detects the modulation envelope?
Last Answer : Emitter-base junction
Description : What causes the change in collector current in an emitter injection modulator?
Last Answer : Gain is varied by changing the voltage on the emitter.
Description : What is the purpose of R1?
Last Answer : R1 provides the proper bias to the base of Q1 from VBB .
Description : When an unknown capacitance is tested with a bridge, what is the value of Cx if R1 equals 70 ohms, R2 equals 150 ohms, and Cs equals 550 microfarads?
Last Answer : 256 microfarads.
Description : When a bridge is used to measure resistance, what is the value of Rx if R1 equals 80 ohms, R2 equals 120 ohms, and R3 equals 280 ohms?
Last Answer : 420 ohms.
Description : In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?
Last Answer : 60 millivolts.
Description : In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?
Last Answer : 50 millivolts.
Description : what is the power dissipated in R1?
Last Answer : 1.35 watts.
Description : why is the value of R1 calculated first?
Last Answer : R1 is the bleeder resistor. Bleeder current must be known before any of the remaining divider resistor ohmic values can be computed.
Description : Refer to figure 3-55(A). If the following resistors were replaced with the values indicated: R1 = 900Ω, R3 = 1kΩ, what is the total power in the circuit? What is ER2?
Last Answer : PT = 60 W, ER2 = 10 V.
Description : Is the base region much thinner or much wider than the collector and the emitter regions?
Last Answer : yes its thinnerMost of the free electrons that have entered the base do notrecombine with holes because the base is very thin.
Description : The diagram shown in the illustartion represents a/an _____________. EL-0022 A. magnectic amplifier B. common base amplifier C. common collector amplifier D. common emitter amplifier
Description : In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0022 A. common base B. reverse bias, negative feedback C. common emitter D. common collector
Description : In the illustration, the small battery and Rb are in the circuit to apply ________. EL-0022 A. forward bias to the emitter-base B. reverse bias to the emitter-base C. a 'reference charge' on the input capacitor D. a buffer between the input ground and the emitter ground
Description : In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0045 A. common emitter B. common collector C. darlington paired, capacitor coupled D. common base
Description : In the illustration, the large battery and R(L) are in the circuit to ________. EL-0022 A. forward bias the emitter-base B. reverse bias the emitter-base C. forward bias the emitter/collector D. reverse bias the emitter/collector
Description : As shown in the illustration, which of the elements listed does the line 'B' represent in the basic schematic symbol of a PNP transistor? EL-0068 A. Base B. Emitter C. Cathode D. Collector
Description : Which of the following actions can be carried out in order to prevent thermal runaway in a transistor? A. Increase the current through the collector-base junction. B. Install a heat sink. ... point to increase collector current. D. Increase the potential difference between the emitter and the base.
Description : The device in figure 'B' shown in the illustration will conduct when the ____________. EL-0067 A. base-emitter is forward biased and the collector-base is reverse biased B. anode-cathode is forward ... is reversed biased D. terminal 1-2 is forward biased and the emitter-terminal 1 is reverse biased
Description : The leads of the device in figure 'B' shown in the illustration are named _________. EL-0065 A. source, gate and drain B. emitter, base and collector C. emitter, base 1 and base 2 D. anode, cathode and gate