Non-inverting amplifier circuits have _______ (a) Very high input impedance (b) very low input impedance (c) low output impedance (d) none of above

Non-inverting amplifier circuits have _______
(a) Very high input impedance (b) very low input impedance
(c) low output impedance (d) none of above
by

1 Answer

Answer :

(a) Very high input impedance
by

Related questions

The gain G of non-inverting amplifier is (a) G = − R2 R1 (b) G = 1 + R2 R1 (c) G = R2 R1 (d) G = 1 − R2 R1

Description : The gain G of non-inverting amplifier is (a) G = − R2 R1 (b) G = 1 + R2 R1 (c) G = R2

Last Answer : (b) G = 1 + R2 R1

For non-inverting amplifier the input and output is A. out of phase B. in phase C. have phase difference of 180° D. have phase difference of 90°

Description : For non-inverting amplifier the input and output is A. out of phase B. in phase C. have phase difference of 180° D. have phase difference of 90°

Last Answer : in phase

One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Description : One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Last Answer : d. To prevent reradiation of the local oscillator

Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output impedance C. low input impedance, low gain and high output impedance D. low input impedance, high gain and low output impedance

Description : Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output ... gain and high output impedance D. low input impedance, high gain and low output impedance

Last Answer : Answer: A

In inverting amplifier, the phase difference between input and output voltages must be A. 30° B. 45° C. 90° D. 180°

Description : In inverting amplifier, the phase difference between input and output voltages must be A. 30° B. 45° C. 90° D. 180°

Last Answer : 180°

The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Description : The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Last Answer : (d) inverter

In an inverting amplifier the non-inverting input (+) is connected to A. 1 V line B. 0 V line C. 2 V line D. 3 V line

Description : In an inverting amplifier the non-inverting input (+) is connected to A. 1 V line B. 0 V line C. 2 V line D. 3 V line

Last Answer :  0 V line

The operational amplifier is _______ (a) High gain amplifier (b) high power amplifier (c)high resistance amplifier (d)low resistance amplifier

Description : The operational amplifier is _______ (a) High gain amplifier (b) high power amplifier (c)high resistance amplifier (d)low resistance amplifier

Last Answer : a) High gain amplifier

One feature of the operational amplifier is that it can have ____________. A. up to ten outputs B. binary coded decimal inputs C. several hundred amps at the output D. inverting and non-inverting inputs

Description : One feature of the operational amplifier is that it can have ____________. A. up to ten outputs B. binary coded decimal inputs C. several hundred amps at the output D. inverting and non-inverting inputs

Last Answer : Answer: D

The electronic circuits which implement the various logic operations are called ________ (a) Logic gates (b) Boolean algebra (c) amplifier gain (d) logic functions

Description : The electronic circuits which implement the various logic operations are called ________ (a) Logic gates (b) Boolean algebra (c) amplifier gain (d) logic functions

Last Answer : a) Logic gates

Why We Giving Input To Electronic Amplifier In Inverting Pin? What Is The Reason Behind That?

Description : Why We Giving Input To Electronic Amplifier In Inverting Pin? What Is The Reason Behind That?

Last Answer : if we need a phase shift than we give input n inverting pin or when we need to boost signal at higher level, i.e; using cascade stages of amplification(even) than we also use inverting pin.

In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Description : In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Last Answer : 0 volts.

To provide its unique characteristics to analog circuits, the operational amplifier is made up of a/an ______________. A. voltage amp, current amp and output amp B. input amp, power amp and output amp C. scaling amp, power amp and voltage amp D. differential amp, voltage amp and output amp

Description : To provide its unique characteristics to analog circuits, the operational amplifier is made up of a/an ______________. A. voltage amp, current amp and output amp B. input amp, power amp and output amp C. scaling amp, power amp and voltage amp D. differential amp, voltage amp and output amp

Last Answer : Answer: D

Silicon transistors are preferred because: (a) High operating temperature (b) Low leakage current (c) Suited to high frequency circuits (d) All

Description : Silicon transistors are preferred because: (a) High operating temperature (b) Low leakage current (c) Suited to high frequency circuits (d) All

Last Answer : (d) All

Define non-inverting amplifier?

Description : Define non-inverting amplifier?

Last Answer : The input is applied to the non-inverting input terminal and the inverting terminal connected to the ground.

EMDis best describe bywhich statement? a. 70percentofthe corediameter and70%ofthefiberNAshouldbe filled with light b.70 percent of the fiber diameter and 70% of the cone of acceptance should be filled with light c.70 percent of input light should be measured at the output d.70 percent of the unwanted wavelengths should be attenuated by the fiber

Description : EMDis best describe bywhich statement? a. 70percentofthe corediameter and70%ofthefiberNAshouldbe filled with light b.70 percent of the fiber diameter and 70% of the cone of acceptance should be filled with ... the output d.70 percent of the unwanted wavelengths should be attenuated by the fiber

Last Answer : a. 70percentofthe corediameter and70%ofthefiberNAshouldbe filled with light

The termresponsivityasit appliesto a light detectorisbest described as a. the time required for the signal to go from 10 to 90 percent of maximum amplitude b.the ratio ofthediode output currentto opticalinputpower c. the ratio of output current to output power d. the ratio of output current to input current

Description : The termresponsivityasit appliesto a light detectorisbest described as a. the time required for the signal to go from 10 to 90 percent of maximum amplitude b.the ratio ofthediode output currentto ... of output current to output power d. the ratio of output current to input current

Last Answer : b.the ratio ofthediode output currentto opticalinputpower

When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage is being measured B. input impedance much less than the impedance across which the voltage is being measured C. sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Description : When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage ... sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Last Answer : Answer: A

The signal to the circuit on card 'A0AA2' at coordinate '29Q' shown in the illustration is on the ____________. EL-0099 A. non-inverting input at pin '20' B. inverting input at pin '16' C. non-inverting input at pin '14' D. inverting input at pin '46'

Description : The signal to the circuit on card 'A0AA2' at coordinate '29Q' shown in the illustration is on the ____________. EL-0099 A. non-inverting input at pin '20' B. inverting input at pin '16' C. non-inverting input at pin '14' D. inverting input at pin '46'

Last Answer : Answer: B

Why are the 2 input terminals of an op-amp are called as inverting & non-inverting terminals?

Description : Why are the 2 input terminals of an op-amp are called as inverting & non-inverting terminals?

Last Answer : Ans-Because if we give input to one input means that will produce the same phase output where as the other(Inverting) pin produce 180 degree phase shifted output.

Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Description : Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Last Answer : A) It has low input impedance

The opposition to the establishment of magnetic lines of force in a magnetic circuit is called the circuit's _______. A. resistance B. reluctance C. impedance D. inductance

Description : The opposition to the establishment of magnetic lines of force in a magnetic circuit is called the circuit's _______. A. resistance B. reluctance C. impedance D. inductance

Last Answer : Answer: B

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

What components form the input-signal-developing impedance for the amplifier?

Description : What components form the input-signal-developing impedance for the amplifier?

Last Answer : C2 and the secondary of T1.

If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?

Description : If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?

Last Answer : The gain increases.

The 'function generator' of the control circuit illustrated _______________. EL-0095 A. can be programmed to produce a non-linear output for a linear input depending on operating conditions B. is used for controlling relay contacts' positions in selection circuits C. automatically selects which or how many engines are needed for a required vessel speed D. all of the above

Description : The 'function generator' of the control circuit illustrated _______________. EL-0095 A. can be programmed to produce a non-linear output for a linear input depending on operating conditions B. is used for ... which or how many engines are needed for a required vessel speed D. all of the above

Last Answer : Answer: A

Process of conversion low voltage to high voltage is called _______ (a) Rectification (b)forward bias (c) reverse bias (d) amplification

Description : Process of conversion low voltage to high voltage is called _______ (a) Rectification (b)forward bias (c) reverse bias (d) amplification

Last Answer : (d) amplification

The purpose of a short circuit forcing module (short time trip) installed in a branch line is to provide ____________. A. high speed clearance of low impedance short circuits in the branch B. continuity of service on main bus under short circuit conditions in a branch C. isolation of short circuits by selective tripping of branch circuit breakers D. all of the above

Description : The purpose of a short circuit forcing module (short time trip) installed in a branch line is to provide ____________. A. high speed clearance of low impedance short circuits in the branch B. ... C. isolation of short circuits by selective tripping of branch circuit breakers D. all of the above

Last Answer : Answer: D

What is the type of feedback employed in the inverting op-amp amplifier?

Description : What is the type of feedback employed in the inverting op-amp amplifier?

Last Answer : Negative feedback is employed in the inverting op-amp amplifier.

The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is

Description : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

Last Answer : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

The closed-loop voltage gain of an inverting amplifier equal to

Last Answer : The closed-loop voltage gain of an inverting amplifier equal to The feedback resistance divided by the input resistance.

Short-circuited stubs are preferred to open-circuited stubs because thelatter are a. more difficult to make an connect b. made of a transmission line with a different characteristic impedance c. liable to radiate

Description : Short-circuited stubs are preferred to open-circuited stubs because thelatter are a. more difficult to make an connect b. made of a transmission line with a different characteristic impedance c. liable to radiate

Last Answer : c. liable to radiate

Impedance inversionmaybe obtainedwith a. a short-circuited stub b. an open-circuited stub c. a quarter-wave line d. a half-wave line

Description : Impedance inversionmaybe obtainedwith a. a short-circuited stub b. an open-circuited stub c. a quarter-wave line d. a half-wave line

Last Answer : c. a quarter-wave line

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Description : Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Last Answer : A. 39.4

If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?

Description : If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?

Last Answer : The gain decreases.

For Cascode amplifier the output impedance becomes

Description : For Cascode amplifier the output impedance becomes 

Last Answer : For Cascode amplifier the output impedance becomes very high

An amplifier is said to suffer from distortion when its output is - (1) low (2) different from input (3) noisy (4) larger than its input

Description : An amplifier is said to suffer from distortion when its output is - (1) low (2) different from input (3) noisy (4) larger than its input

Last Answer : (3) noisy Explanation: Amplifier Distortion can take on many forms such as Amplitude, Frequency and Phase Distortion due to Clipping. For a signal amplifier to operate correctly without any distortion to the output signal, it requires some form of DC Bias on its Base or Gate terminal.

Thermistor with high negative temperature coefficient are very accurate for measuring low temperature especially near is a. 10 K b. 70K c. 200K d. 35K

Description : Thermistor with high negative temperature coefficient are very accurate for measuring low temperature especially near is a. 10 K b. 70K c. 200K d. 35K

Last Answer : c. 200K

What is the speaker driving voltage of an amplifier?

Description : What is the speaker driving voltage of an amplifier?

Last Answer : I have to ask WHY? That said, Speakers and a light bulb are two different types of load, and the the lights will probably fry the output transistor.

SI unit of gain of amplifier is (a) Volt (b) ampere (c) coulomb (d) dimensionless

Description : SI unit of gain of amplifier is (a) Volt (b) ampere (c) coulomb (d) dimensionless

Last Answer : (d) dimensionless

The open loop gain of the amplifier is ______ (a) 105 (b) 103 (c) 106 (d) 108

Description : The open loop gain of the amplifier is ______ (a) 105 (b) 103 (c) 106 (d) 108

Last Answer : (a) 105

In the inverting configuration when the noninverting input is grounded, the inverting input is at (signal, virtual) ground

Description : In the inverting configuration when the noninverting input is grounded, the inverting input is at (signal, virtual) ground

Last Answer : Virtual.

In the inverting configuration, the input signal is applied to the (a) (inverting, noninverting) input and the feedback signal is applied to the (b) (inverting, noninverting) input.

Description : In the inverting configuration, the input signal is applied to the (a) (inverting, noninverting) input and the feedback signal is applied to the (b) (inverting, noninverting) input.

Last Answer : a. Inverting. b. Inverting.

If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the input signal C) Need for high dc collector supply D) Clipping of output in the negative half of the input signal

Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal

Last Answer : B) Clipping of output in the positive half of the input signal

Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection

Description : Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection

Last Answer : A. input

What impedance relationship between the output of one circuit and the input of another circuit will provide the maximum power transfer?

Description : What impedance relationship between the output of one circuit and the input of another circuit will provide the maximum power transfer?

Last Answer : Equal impedance.

A linear network has a current input 4cos(ω t + 20º)A and a voltage output 10 cos(ωt +110º) V. Determine the associated impedance.

Description : A linear network has a current input 4cos(ω t + 20º)A and a voltage output 10 cos(ωt +110º) V. Determine the associated impedance.

Last Answer : Solution

Compare BJT common base configuration with common collector configuration on the basis of (i) Current gain (ii) Voltage gain (iii) Input impedance (iv) Output impedance

Description : Compare BJT common base configuration with common collector configuration on the basis of (i) Current gain (ii) Voltage gain (iii) Input impedance (iv) Output impedance

Last Answer : Parameter Common Base Common Collector Current gain Low (About 1) High (1+β) Voltage gain High 1  Input impedance  Low High Output impedance High Low

Why is input impedance of the FET very high?

Description : Why is input impedance of the FET very high?

Last Answer : BECAUSE its input circuit (gate to source) is reverse biased and input gate current is very small.