Two tape recorders have signal-to-noise ratios (SNRs) of 25-dB RMS and 35-dB RMS respectively. Which of the SNRs can record and reproduce the widest range of input signals and why?

Two tape recorders have signal-to-noise ratios (SNRs) of  25-dB RMS and 35-dB RMS respectively. Which of the SNRs can  record and reproduce the widest range of input signals and  why?
by

1 Answer

Answer :

35-dB RMS because the highest SNR can always record and  reproduce the widest range of input signals.
by

Related questions

What two types of record and reproduce electronics are used by magnetic tape recorders?

Description : What two types of record and reproduce electronics are used by magnetic tape recorders?

Last Answer : . a. Direct record (AM). b. Frequency modulation (FM).

The equalization and phase correction circuit in a tape recorder’s direct reproduce electronics (figure 5-2) performs what function?

Description : The equalization and phase correction circuit in a tape recorder’s direct reproduce electronics (figure 5-2) performs what function?

Last Answer : It generates an equalization signal which corrects any frequency response problems in the input signal from the pre-amplifier circuit.

What two specifications determine the maximum frequency that a recorder's record and reproduce heads will be able to transfer?

Description : What two specifications determine the maximum frequency that a recorder's record and reproduce heads will be able to transfer?

Last Answer : a. Size of the headgap. b. Speed of the magnetic tape.

A recorder's erase head is always placed in what sequence on the record/reproduce track?

Description : A recorder's erase head is always placed in what sequence on the record/reproduce track?

Last Answer : . First, before the record and reproduce heads.

Why are record heads always placed before reproduce heads on recorders?

Description : Why are record heads always placed before reproduce heads on recorders?

Last Answer : Allow you to monitor the signals you're recording.

The head driver circuit of a tape recorder’s FM record electronics (figure 5-4) performs what function?

Description : The head driver circuit of a tape recorder’s FM record electronics (figure 5-4) performs what function?

Last Answer : It amplifies the frequency-modulated output from the record oscillator and sends it to the record head.

The head driver circuit in a tape recorder’s direct record electronics component (figure 5-1) performs what function?

Description : The head driver circuit in a tape recorder’s direct record electronics component (figure 5-1) performs what function?

Last Answer : It takes the signal from the summing network, amplifies it, and sends it to the record head for recording.

Which of the two types of magnetic tape is used to record audio and instrumentation type signals in the VLF to 2.5MHz frequency range?

Description : Which of the two types of magnetic tape is used to record audio and instrumentation type signals in the VLF to 2.5MHz frequency range?

Last Answer : Analog magnetic tape.

An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Last Answer : B. 4.0 µV

Acceptable "Noise Pollution Level" in India range between: (1) 16 - 35 db (2) 40 - 45 db (3) 70 - 100 db (4) 10 - 15 db

Description : Acceptable "Noise Pollution Level" in India range between: (1) 16 - 35 db (2) 40 - 45 db (3) 70 - 100 db (4) 10 - 15 db

Last Answer : (2) 40 - 45 db Explanation: According to the noise pollution rules, the permissible noise level during the day is 50dB in silence zones, 55dB in residential areas, 65 dB in commercial areas and 75 ... areas, commercial areas and industrial areas are respectively 40 dB, 45 dB, 55 dB and 70 dB.

While measuring frequency response, as the signal generator approaches the lowest and highest frequency the recorder can effectively record, the VTVM reading drops to less than - 3 dB. What does this indicate?

Description : While measuring frequency response, as the signal generator approaches the lowest and highest frequency the recorder can effectively record, the VTVM reading drops to less than - 3 dB. What does this indicate?

Last Answer : The upper and lower limits of the frequency response specification for that tape recorder.

What category of digital tape recorder is used to record special signals with a bandwidth of less than 500 kHz?

Description : What category of digital tape recorder is used to record special signals with a bandwidth of less than 500 kHz?

Last Answer : Instrumentation digital tape recorders.

What are two disadvantages of using a recorder’s erase head to erase data recorded on a magnetic tape?

Description : What are two disadvantages of using a recorder’s erase head to erase data recorded on a magnetic tape?

Last Answer : Using an erase head is slow, and it may not completely erase the tape.

Which digital data encoding method helps overcome a tape recorder’s low-frequency response problems by recording two logic levels for each incoming data bit?

Description : Which digital data encoding method helps overcome a tape recorder’s low-frequency response problems by recording two logic levels for each incoming data bit?

Last Answer : Bi-phase level encoding.

What type of reeling system best controls a tape recorder's tape tension during starts and stops?

Description : What type of reeling system best controls a tape recorder's tape tension during starts and stops?

Last Answer : A tape buffering reeling system

What are the four basic parts of a magnetic tape recorder's tape transport system?

Description : What are the four basic parts of a magnetic tape recorder's tape transport system?

Last Answer : a. Tape reeling system. b. Tape speed control system. c. Electronic subsystem. d. Basic enclosure.

What causes flutter in a tape recorder’s output?

Description : What causes flutter in a tape recorder’s output?

Last Answer : Non-uniform tape motion caused by variations in tape speed.

What number harmonic is the primary harmonic distortion in magnetic tape recorders?

Description : What number harmonic is the primary harmonic distortion in magnetic tape recorders?

Last Answer : Third-order harmonic.

List four factors that can degrade the frequency response of magnetic tape recorders.

Description : List four factors that can degrade the frequency response of magnetic tape recorders.

Last Answer : a. A too-high or too-low bias signal level setting for the record head. b. An improper reproduce head gap. c. An improper tape transport speed. d. Poor tape-to-head contact.

Technical manuals for tape recorders can state the SNR in what three different ways?

Description : Technical manuals for tape recorders can state the SNR in what three different ways?

Last Answer : a. Root-mean-square (RMS) signal-to-RMS noise. b. Peak-to-peak signal-to-RMS noise. c. Peak signal-to-RMS noise.

You plan to measure your tape recorder’s SNR. What test equipment will you need?

Description : You plan to measure your tape recorder’s SNR. What test equipment will you need?

Last Answer : A VTVM and a signal generator.

Magnetic tape recorders can have up to three different heads installed. What are the three functions performed by a recorder's heads?

Description : Magnetic tape recorders can have up to three different heads installed. What are the three functions performed by a recorder's heads?

Last Answer : Record, reproduce, and erase.

What method for erasing magnetic tape is much more effective and reliable than using a recorder’s erase head?

Description : What method for erasing magnetic tape is much more effective and reliable than using a recorder’s erase head?

Last Answer : Using a magnetic tape degausser

After using a tape that was stored in an area where temperatures exceeded 130º F you notice pieces of oxide sticking to the recorder's tape-transport mechanism, to its magnetic heads, and onto the tape. What is the probable cause of these symptoms?

Description : After using a tape that was stored in an area where temperatures exceeded 130º F you notice pieces of oxide sticking to the recorder's tape-transport mechanism, to its magnetic heads, and onto the tape. What is the probable cause of these symptoms?

Last Answer : Oxide shedding. At temperatures above 130º F, oxide coating becomes soft and sheds.

Digital magnetic tape recorders used to store and retrieve digital data fall into what three categories?

Description : Digital magnetic tape recorders used to store and retrieve digital data fall into what three categories?

Last Answer : a. Computer-compatible digital tape recorders. b. Telemetry digital tape recorders. c. Instrumentation digital tape recorders

Which single phase ac motor will you select for record players and tape recorders?

Description :  Which single phase ac motor will you select for record players and tape recorders?  a) Hysteresis motor b) Shaded pole motor c) Reluctance motor d) Two value capacitor motor

Last Answer : Which single phase ac motor will you select for record players and tape recorders?  Hysteresis motor

You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Description : You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Last Answer : C. 35

What type of tape error causes noise to appear on the tape when no signal should appear? What causes this type of tape error?

Description : What type of tape error causes noise to appear on the tape when no signal should appear? What causes this type of tape error?

Last Answer : Noise error is usually caused by a cut or a scratch on the magnetic tape.

A recorder’s harmonic-distortion specification reads 2% third harmonic of a 100-kHz signal at 60 ips. What does this mean?

Description : A recorder’s harmonic-distortion specification reads 2% third harmonic of a 100-kHz signal at 60 ips. What does this mean?

Last Answer : The recorder has 2% third-harmonic distortion of a 100-kHz signal at 60 ips.

If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?

Description : If If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?

Last Answer : 200 millivolts.

If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Last Answer : . A different shape than the input signals but larger in amplitude.

If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?

Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?

Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than

. If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?

Description : . If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?

Last Answer : No output (the signals will "cancel out").

Why does adding dc vice ac bias voltage to the input signal result in a poor signal-to-noise ratio (SNR)?

Description : Why does adding dc vice ac bias voltage to the input signal result in a poor signal-to-noise ratio (SNR)?

Last Answer : With dc bias, the SNR is poor because only a small portion of the magnetism curve is straight enough to use, thus the output signal is weak compared with the natural tape hiss.

How should a tape recorder with good phase response reproduce a complex waveform, such as a square wave?

Description : How should a tape recorder with good phase response reproduce a complex waveform, such as a square wave?

Last Answer : With no distortion

The frequency-response specification of your tape recorder reads within +/ - 3 dB from 150 Hz to 150 kHz at 60 ips. What does this mean?

Description : The frequency-response specification of your tape recorder reads within +/ - 3 dB from 150 Hz to 150 kHz at 60 ips. What does this mean?

Last Answer : The recorder can record all frequencies between 150 Hz and 150 kHz at 60 ips without varying the output amplitude more than 3 dB.

Most record and reproduce heads are in one of what three bandwidth categories?

Description : Most record and reproduce heads are in one of what three bandwidth categories?

Last Answer : a. Narrowband—100 Hz to 100 kHz. b. Intermediate band—100 Hz to 500 kHz. c. Wideband—400 Hz to 2 mHz.

The noise from an airplane engine 100 ft from an observer is found to have an intensity of 45dB. What will be the intensity when the plane flies overhead at an altitude of 1 mi? A. 10.5 dB B. 34.5 dB C. 35 dB D. 20.5 dB

Description : The noise from an airplane engine 100 ft from an observer is found to have an intensity of 45dB. What will be the intensity when the plane flies overhead at an altitude of 1 mi? A. 10.5 dB B. 34.5 dB C. 35 dB D. 20.5 dB

Last Answer : A. 10.5 dB

The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, respectively. Calculate the equivalent input-noise resistance of this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Description : The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, ... this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Last Answer : B. 2,518 Ω

Most AC voltmeters have an rms scale which is valid only if the input signal being measured is a __ signal.

Description : Most AC voltmeters have an rms scale which is valid only if the input signal being measured is a __ signal.

Last Answer : sinusoidal

if noise voltage =120 mv and signal voltage = 80 v , S/N ratio in dB is?

Description : if noise voltage =120 mv and signal voltage = 80 v , S/N ratio in dB is?

Last Answer : Answers is the place to go to get the answers you need and to ask the questions you want

Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Description : Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Last Answer : A. 5.23 dB

What signal-to-noise ratio is required for satisfactory television reception? A. 10 dB B. 30 dB C. 40 dB D. 20 dB

Description : What signal-to-noise ratio is required for satisfactory television reception? A. 10 dB B. 30 dB C. 40 dB D. 20 dB

Last Answer : C. 40 dB

What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Description : What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Last Answer : B. 50 dB

The signal to noise ratio that is required for a satisfactory television reception. A. 30 dB B. 40 dB C. 10 dB D. 20 dB

Description : The signal to noise ratio that is required for a satisfactory television reception. A. 30 dB B. 40 dB C. 10 dB D. 20 dB

Last Answer : B. 40 dB

What signal-to-noise ratio is required for satisfactory telephone services? A. 50 dB B. 30 dB C. 40dB D. 20 dB

Description : What signal-to-noise ratio is required for satisfactory telephone services? A. 50 dB B. 30 dB C. 40dB D. 20 dB

Last Answer : A. 50 dB

The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Description : The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Last Answer : D. 14 dB

If a sudden loud noise in the range of 100-150 dB ruptured one's eardrum and caused bleeding from the ears how long would it take for hearing to return in a best case scenario?

Description : If a sudden loud noise in the range of 100-150 dB ruptured one's eardrum and caused bleeding from the ears how long would it take for hearing to return in a best case scenario?

Last Answer : An internet search was not definitive on whether or not the eardrums would rupture, but there is the possibility. If this is describing an actual situation, your time would be best spent talking to a doctor.

Can a sudden loud noise in the range of 100-150 dB cause bleeding from the nose?

Description : Can a sudden loud noise in the range of 100-150 dB cause bleeding from the nose?

Last Answer : An internet search found one page that indicated a high-dB level might cause a nose bleed, but that would be unusual. If you are describing a current condition, your time would be better spent talking with a doctor.

Why is it important to minimize TBE jitter in magnetic tape recordings where precise timing relationships exist between two or more signals?

Description : Why is it important to minimize TBE jitter in magnetic tape recordings where precise timing relationships exist between two or more signals?

Last Answer : The jitter could cause noise and a loss of accuracy.