Description : The principle used for control of deflection in beams and slabs. [ A ] Maxwell method [ B ] Mohr‟s theorem [ C ] Span to effective depth ratio [ D ] Span to overall depth ratio.
Last Answer : [ C ] Span to effective depth ratio
Description : Under normal conditions using an ordinary cement, the period of removal of the form work, is: (A) 7 days for beam soffits (B) 14 days for bottom slabs of spans 4.6 m and more (C) 21 days for bottom beams over 6 m spans (D) All the above
Last Answer : Answer: Option D
Description : If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm
Last Answer : Answer: Option C
Description : The Maximum spacing of Main reinforcement „m‟ slabs shall be [ A ] Less than three times of the effective depth [ B ] Less than 300mm [ C ] Smaller of (a) and (b) [ D ] Greater of (a) and (b)
Last Answer : [ C ] Smaller of (a) and (b)
Description : The Maximum shear stress in Slabs should not exceed -------- the maximum values allowed for beams. [ A ] Half Of [ B ] One-Fourth Of [ C ] Twice [ D ] Those Given In
Last Answer : [ A ] Half Of
Description : The Maximum spacing of Secondary reinforcement in slabs should be [ A ] Less than 450 mm [ B ] Less than 300 mm [ C ] Smaller of three times the effective depth and 450 mm [ D ] Smaller of five times the effective depth and 450 mm
Last Answer : [ D ] Smaller of five times the effective depth and 450 mm
Description : For the design of a simply supported T-beam the ratio of the effective span to the overall depth of the beam is limited to (A) 10 (B) 15 (C) 20 (D) 25
Description : Beams of uniform strength are preferred to those of uniform section because these are economical for (A) Large spans (B) Heavy weights (C) Light weights (D) Short spans
Last Answer : (A) Large spans
Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6
Description : A bridge is generally specified as “Br. No. 180 (5x9.10m G) at km 345/5-6”. a) Effective Span b) Width of bridge c) Clear Span* d) Overall length of bridge
Last Answer : c) Clear Span*
Description : For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m
Last Answer : Answer: Option B
Description : Critical section for shear in case of flat slabs is at a distance of (A) Effective depth of slab from periphery of column/drop panel (B) d/2 from periphery of column/capital/ drop panel (C) At the drop panel of slab (D) At the periphery of column
Description : In slabs the Maximum horizontal distance between parallel main reinforcement should not exceed i.Three times effective depth ii Five times effective depth iii 300mm iv 450 mm [ A ] i and iii [ B ] i and iv [ C ] ii and iii [ D ] ii and iv
Last Answer : [ A ] i and iii
Description : For the construction of R.C.C. slabs, columns, beams, walls, etc. the grade of concrete mix used, is (A) 1 : 3 : 6 (B) 1 : 1½ : 3 (C) 1 : 2 : 4 (D) 1 : 1 : 2
Last Answer : (C) 1 : 2 : 4
Description : Pick up the correct statement from the following: (A) Construction joints in columns are provided a few cm below the junction of beam (B) Construction joints in columns are provided at the bottom ... (C) Construction joints in beams and slabs are provided within middle third (D) All the above
Description : The concrete slump recommended for beams and slabs; is (A) 25 to 50 mm (B) 25 to 75 mm (C) 30 to 125 mm (D) 50 to 100 mm
Description : Pick up the correct statement from the following: (A) The roof slabs of multi-storeyed buildings are constructed monolithically to carry the various floor loads (B) The beams of multi-storeyed ... slab is spanned across the secondary beams provided between the main beams (D) All of these
Description : Vertical construction joints are provided where the shearing forces are minimum in the case of (A) Slabs (B) Beams (C) Girders (D) All of these
Description : A continuous beam shall be deemed to be a deep beam if the ratio of effective span to overall depth, is (A) 2.5 (B) 2.0 (C) Less than 2 (D) Less than 2.5
Last Answer : Answer: Option A
Description : A continuous beam is deemed to be a deep beam when the ratio of effective span to overall depth (1/D) is less than (A) 1.5 (B) 2.0 (C) 2.5 (D) 3.0
Description : The basic value of span to depth ratio for one way continuous slab is [ A ] 20 [ B ] 26 [ C ] 35 [ D ] 40
Last Answer : [ B ] 26
Description : Basic value of span to depth ratio for simply supported beam to control deflection is [ A ] 7 [ B ] 20 [ C ] 26 [ D ] 35
Last Answer : [ B ] 20
Description : Basic value .of Span to Depth ratio for cantilever to control deflection is [ A ] 7 [ B ] 20 [ C ] 26 [ D ] 35
Last Answer : [ A ] 7
Description : An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity ... , is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2
Description : For a cantilever of effective depth of 0.5 m, the maximum span to satisfy vertical deflection limit is (A) 3.5 m (B) 4 m (C) 4.5 m (D) 5 m
Description : Design of R.C.C. simply supported beams carrying U.D.L. is based on the resultant B.M. at (A) Supports (B) Mid span (C) Every section (D) Quarter span
Description : The allowable shear stress in stiffened webs of mild steel beams decreases with (a) Decrease in the spacing of the stiffeners (b) Increase in the spacing of the stiffeners (c) Decrease in the effective depth (d) Increase in the effective depth
Last Answer : (b) Increase in the spacing of the stiffeners
Description : Why is the span length ratio of end span/approach span to its neighboring inner spans usually about 0.75?
Last Answer : From aesthetic point of view, an odd number of spans with a decrease in length in the direction of abutment is desirable. Moreover, spans of equal length are found to be boring. However, the ... the last span in a continuous bridge while approach span refers top the first span of a bridge.
Description : The three moments equation is applicable only when (A) The beam is prismatic (B) There is no settlement of supports (C) There is no discontinuity such as hinges within the span (D) The spans are equal
Last Answer : (C) There is no discontinuity such as hinges within the span
Description : When the slab is supported on all the four edges and the ratio of long span to short span is small, bending takes place along both the spans, such a slab is known as (a) Slab spanning in one direction (b) One way slab. (c) Slab spanning in two direction. (d) Two-way slab.
Last Answer : (d) Two-way slab.
Description : If a rectangular pre-stressed beam of an effective span of 5 meters and carrying a total load 3840 kg/m, is designed by the load balancing method, the central dip of the parabolic tendon should be (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm
Description : For beams of uniform strength, if depth is constant, (A) Width b M (B) Width b M (C) Width b 3 M (D) Width b 1/M
Last Answer : (A) Width b M
Description : According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is ... (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab
Description : Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii
Last Answer : [ A ] i
Description : Couple roof is used for spans (A) 3.5 m or less (B) 3.5 m but less than 5 m (C) 5 m but less than 6.5 m (D) 6.5 m but less than 8 m
Description : Though the effective depth of a T-beam is the distance between the top compression edge to the centre of the tensile reinforcement, for heavy loads, it is taken as (A) 1/8th of the span (B) 1/10th of the span (C) 1/12th of the span (D) 1/16th of the span
Description : The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these
Description : The effective span of a simply supported slab is (a) Distance between the centers of the bearings (b) Clear distance between the inner faces of the walls plus twice he thickness of the slab. (c) Cleat spa plus effective depth of the slab. (d) All the above
Last Answer : (c) Cleat spa plus effective depth of the slab.
Description : The breadth of the flange of a T-beam is (a) 1/3rd of the effective span of the T-beam (b) Twelve times the depth of slab plus breadth of rib. (c) Centre to centre distance between the adjacent beam. (d) Least of (a) , (b) or (c)
Last Answer : (d) Least of (a) , (b) or (c)
Description : The span/effective depth ratio is ----------------- for control of deflection [ A ] An exact method [ B ] An empirical method [ C ] An accurate method. [ D ] Both (a) and (c)
Last Answer : [ B ] An empirical method
Description : For normal cases, stiffness of a simply supported beam is satisfied if the ratio of its span to its overall depth does not exceed (A) 10 (B) 15 (C) 20 (D) 25
Description : A simply supported beam A carries a point load at its mid span. Another identical beam B carries the same load but uniformly distributed over the entire span. The ratio of the maximum deflections of the beams A and B, will be (A) 2/3 (B) 3/2 (C) 5/8 (D) 8/5
Last Answer : (D) 8/5
Description : Design of R.C.C. cantilever beams, is based on the resultant force at (A) Fixed end (B) Free end (C) Mid span (D) Mid span and fixed support
Description : For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9
Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6
Last Answer : (c) 0.9
Description : The date of painting of steel work should be painted in white on the out side of the left girder a) of the 1st span only b) first span only but on all spans for Imp. Bridges* c) of the all spans d) None of the above
Last Answer : b) first span only but on all spans for Imp. Bridges*
Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 ... joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm
Last Answer : (D) 400 mm
Description : The maximum ratio of span to depth of a slab simply supported and spanning in one direction, is (A) 35 (B) 25 (C) 30 (D) 20
Description : The maximum ratio of span to depth of a slab simply supported and spanning in one direction is (a) 35 (b) 25 (c) 30 (d) 20
Last Answer : (c) 30
Description : According to IS: 456-2000, the span/overall depth ratio for a continuous two-way slab in order to control deflection is given by [ A ] 20 [ B ] 28 [ C ] 32 [ D ] 40
Last Answer : [ C ] 32