The maximum ratio of span to depth of a slab simply supported and spanning in one direction, is (A) 35 (B) 25 (C) 30 (D) 20

The maximum ratio of span to depth of a slab simply supported and spanning in one direction, is
(A) 35
(B) 25
(C) 30
(D) 20
by

1 Answer

Answer :

Answer: Option C
by

Related questions

The maximum ratio of span to depth of a slab simply supported and spanning in one direction is (a) 35 (b) 25 (c) 30 (d) 20

Description : The maximum ratio of span to depth of a slab simply supported and spanning in one direction is (a) 35 (b) 25 (c) 30 (d) 20

Last Answer : (c) 30

The maximum ratio of span to depth of a slab simply supported and spanning in two directions, is (A) 25 (B) 30 (C) 35 (D) 40

Description : The maximum ratio of span to depth of a slab simply supported and spanning in two directions, is (A) 25 (B) 30 (C) 35 (D) 40

Last Answer : Answer: Option C

The maximum ratio of span to depth of a slab simple supported and spanning in two directions, is (a) 25 (b) 30 (c) 35 (d) 40

Description : The maximum ratio of span to depth of a slab simple supported and spanning in two directions, is (a) 25 (b) 30 (c) 35 (d) 40

Last Answer : (c) 35

When the slab is supported on all the four edges and the ratio of long span to short span is small, bending takes place along both the spans, such a slab is known as (a) Slab spanning in one direction (b) One way slab. (c) Slab spanning in two direction. (d) Two-way slab.

Description : When the slab is supported on all the four edges and the ratio of long span to short span is small, bending takes place along both the spans, such a slab is known as (a) Slab spanning in one direction (b) One way slab. (c) Slab spanning in two direction. (d) Two-way slab.

Last Answer : (d) Two-way slab.

If the sides o a slab simply supported on its edges and spanning in two way are equal, then the maximum bending moment is multiplied by. (a) 0.25 (b) 0.50 (c) 0.75 (d) 0.85

Description : If the sides o a slab simply supported on its edges and spanning in two way are equal, then the maximum bending moment is multiplied by. (a) 0.25 (b) 0.50 (c) 0.75 (d) 0.85

Last Answer : (b) 0.50

The span/over all depth ratio for a simply supported two-way slab according to IS : 456- 2000 is given by

Description : The span/over all depth ratio for a simply supported two-way slab according to IS : 456- 2000 is given by [ A ] 20 [ B ] 28 [ C ] 32 [ D ] 40

Last Answer : [ B ] 28

Basic value of span to depth ratio for simply supported beam to control deflection is [ A ] 7 [ B ] 20 [ C ] 26 [ D ] 35

Description : Basic value of span to depth ratio for simply supported beam to control deflection is [ A ] 7 [ B ] 20 [ C ] 26 [ D ] 35

Last Answer : [ B ] 20

If the sides of a slab simply supported on edges and spanning in two directions are equal, the maximum bending moment is multiplied by (A) 0.2 (B) 0.3 (C) 0.4 (D) 0.5

Description : If the sides of a slab simply supported on edges and spanning in two directions are equal, the maximum bending moment is multiplied by (A) 0.2 (B) 0.3 (C) 0.4 (D) 0.5

Last Answer : Answer: Option D

For the design of a simply supported T-beam the ratio of the effective span to the overall depth of the beam is limited to (A) 10 (B) 15 (C) 20 (D) 25

Description : For the design of a simply supported T-beam the ratio of the effective span to the overall depth of the beam is limited to (A) 10 (B) 15 (C) 20 (D) 25

Last Answer : Answer: Option C

For normal cases, stiffness of a simply supported beam is satisfied if the ratio of its span to its overall depth does not exceed (A) 10 (B) 15 (C) 20 (D) 25

Description : For normal cases, stiffness of a simply supported beam is satisfied if the ratio of its span to its overall depth does not exceed (A) 10 (B) 15 (C) 20 (D) 25

Last Answer : Answer: Option C

The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these

Description : The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these

Last Answer : Answer: Option B

The effective span of a simply supported slab is (a) Distance between the centers of the bearings (b) Clear distance between the inner faces of the walls plus twice he thickness of the slab. (c) Cleat spa plus effective depth of the slab. (d) All the above

Description : The effective span of a simply supported slab is (a) Distance between the centers of the bearings (b) Clear distance between the inner faces of the walls plus twice he thickness of the slab. (c) Cleat spa plus effective depth of the slab. (d) All the above

Last Answer : (c) Cleat spa plus effective depth of the slab.

The ratio of the length and depth of a simply supported rectangular beam which experiences maximum bending stress equal to tensile stress, due to same load at its mid span, is (A) 1/2 (B) 2/3 (C) 1/4 (D) 1/3

Description : The ratio of the length and depth of a simply supported rectangular beam which experiences  maximum bending stress equal to tensile stress, due to same load at its mid span, is  (A) 1/2  (B) 2/3  (C) 1/4  (D) 1/3

Last Answer : (B) 2/3 

A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated load W at its mid-span. The same bar experiences an extension e under same tensile load. The ratio of the maximum deflection to the elongation, is (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Description : A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated  load W at its mid-span. The same bar experiences an extension e under same tensile load. The  ratio of the maximum deflection to the ... (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Last Answer : (C) (L/2d)

The basic value of span to depth ratio for one way continuous slab is [ A ] 20 [ B ] 26 [ C ] 35 [ D ] 40

Description : The basic value of span to depth ratio for one way continuous slab is [ A ] 20 [ B ] 26 [ C ] 35 [ D ] 40

Last Answer : [ B ] 26

If the ratio of the span to the overall depth does not exceed 10, the stiffness of the beam will ordinarily be satisfactory in case of a (A) Simply supported beam (B) Continuous beam (C) Cantilever beam (D) None of these

Description : If the ratio of the span to the overall depth does not exceed 10, the stiffness of the beam will ordinarily be satisfactory in case of a (A) Simply supported beam (B) Continuous beam (C) Cantilever beam (D) None of these

Last Answer : Answer: Option C

A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 × 106 N/mm2 , the depth of the joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm

Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so  that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the  value of E = 0.2 ... joist, is  (A) 200 mm  (B) 250 mm  (C) 300 mm  (D) 400 mm 

Last Answer : (D) 400 mm 

In a simply supported slab, alternate bars are curtailed at (A) 1/4th of the span (B) 1/5th of the span (C) 1/6th of the span (D) 1/7th of the span

Description : In a simply supported slab, alternate bars are curtailed at (A) 1/4th of the span (B) 1/5th of the span (C) 1/6th of the span (D) 1/7th of the span

Last Answer : Answer: Option D

In a simply supported slab, alternate bars are curtailed at (a) 1/4th of the span (b) 1/5th of the span (c) 1/6th of the span (d) 1/7th of the span

Description : In a simply supported slab, alternate bars are curtailed at (a) 1/4th of the span (b) 1/5th of the span (c) 1/6th of the span (d) 1/7th of the span

Last Answer : (d) 1/7th of the span

Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ A ] i

The pitch of the main bars in a simply supported slab, should not exceed its effective depth by (A) Three times (B) Four times (C) Five times (D) Six times

Description : The pitch of the main bars in a simply supported slab, should not exceed its effective depth by (A) Three times (B) Four times (C) Five times (D) Six times

Last Answer : Answer: Option D

in a simply supported slab, the pitch of distribution reinforcement should not be more than_____________the effective depth of slab or 60cm which ever is smaller. (a) Double (b) Three times (c) Five times (d) Six times

Description : in a simply supported slab, the pitch of distribution reinforcement should not be more than_____________the effective depth of slab or 60cm which ever is smaller. (a) Double (b) Three times (c) Five times (d) Six times

Last Answer : (c) Five times

The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of 4 tonnes at the centre. The maximum stress in the bottom most fibre at the mid span section, is (A) 13.33 kg/cm2 tensile (B) 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Last Answer : (C) 26.67 kg/cm2 tensile

The ratio of the length and diameter of a simply supported uniform circular beam which experiences maximum bending stress equal to tensile stress due to same load at its mid span, is (A) 1/8 (B) 1/4 (C) 1/2 (D) 1/3

Description : The ratio of the length and diameter of a simply supported uniform circular beam which  experiences maximum bending stress equal to tensile stress due to same load at its mid span, is  (A) 1/8  (B) 1/4  (C) 1/2  (D) 1/3 

Last Answer : (C) 1/2 

A simply supported beam A carries a point load at its mid span. Another identical beam B carries the same load but uniformly distributed over the entire span. The ratio of the maximum deflections of the beams A and B, will be (A) 2/3 (B) 3/2 (C) 5/8 (D) 8/5

Description : A simply supported beam A carries a point load at its mid span. Another identical beam B carries  the same load but uniformly distributed over the entire span. The ratio of the maximum  deflections of the beams A and B, will be  (A) 2/3  (B) 3/2  (C) 5/8  (D) 8/5 

Last Answer : (D) 8/5 

For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Description : For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Last Answer : Answer: Option B

A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the bar, is (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm

Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a  load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending  strain energy stored in the ... (A) 411 N mm  (B) 511 N mm  (C) 611 N mm  (D) 711 N mm 

Last Answer : (C) 611 N mm 

The maximum ratio of span to depth of a cantilever slab, is (A) 8 (B) 10 (C) 12 (D) 16

Description : The maximum ratio of span to depth of a cantilever slab, is (A) 8 (B) 10 (C) 12 (D) 16

Last Answer : Answer: Option C

The maximum ratio of span to depth of a cantilever slab is (a) 8 (b) 10 (c) 12 (d) 14

Description : The maximum ratio of span to depth of a cantilever slab is (a) 8 (b) 10 (c) 12 (d) 14

Last Answer : (c) 12

According to IS: 456-2000, the span/overall depth ratio for a continuous two-way slab in order to control deflection is given by [ A ] 20 [ B ] 28 [ C ] 32 [ D ] 40

Description : According to IS: 456-2000, the span/overall depth ratio for a continuous two-way slab in order to control deflection is given by [ A ] 20 [ B ] 28 [ C ] 32 [ D ] 40

Last Answer : [ C ] 32

If K is a constant depending upon the ratio of the width of the slab to its effective span l, x is the distance of the concentrated load from the nearer support, bw is the width of the area of contact of the concentrated load measured parallel to the supported edge, the effective width of the slab be is (A) K/x (1 + x/d) + bw (B) Kx (1 - x/l) + bw (C) Kx (1 + x/l) + bw (D) All the above

Description : If K is a constant depending upon the ratio of the width of the slab to its effective span l, x is the distance of the concentrated load from the nearer support, bw is the width of the area of contact of the concentrated load measured ... ) Kx (1 - x/l) + bw (C) Kx (1 + x/l) + bw (D) All the above

Last Answer : Answer: Option B

For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9

Description : For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9

Last Answer : Answer: Option D

The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6

Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6

Last Answer : (c) 0.9

If l1 and l2 are the lengths of long and short spans of a two way slab simply supported on four edges and carrying a load w per unit area, the ratio of the loads split into w1 and w2acting on strips parallel to l2 and l1 is (A) w1/w2 = l2/l1 (B) w1/w2 = (l2/l1)² (C) w1/w2 = (l2/l1)3 (D) w1/w2 = (l2/l1)

Description : If l1 and l2 are the lengths of long and short spans of a two way slab simply supported on four edges and carrying a load w per unit area, the ratio of the loads split into w1 and w2acting on strips parallel to l2 and l1 is (A) ... l1 (B) w1/w2 = (l2/l1)² (C) w1/w2 = (l2/l1)3 (D) w1/w2 = (l2/l1)

Last Answer : Answer: Option D

A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.

Description : A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.

Last Answer : d.y/4.

A simply supported beam is of rectangular section.It carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the depth of beam is doubled ,the deflection at the centre would be a.2y b.4y c.y/2 d.y/8.

Description : A simply supported beam is of rectangular section.It carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the depth of beam is doubled ,the deflection at the centre would be a.2y b.4y c.y/2 d.y/8.

Last Answer : d.y/8.

Which one of the following is the correct ratio of plastic moment to yield moment for a simply supported beam of uniform square cross section throughout the span (a) 1.5 (b) 1.7 (c) 2.0 (d) 2.34

Description : Which one of the following is the correct ratio of plastic moment to yield moment for a simply supported beam of uniform square cross section throughout the span (a) 1.5 (b) 1.7 (c) 2.0 (d) 2.34

Last Answer : (a) 1.5

The analysis of slab spanning in one direction is done by assuming it to be a beam of (a) 1m length (b) 1m width (c) 1m (d) None of these

Description : The analysis of slab spanning in one direction is done by assuming it to be a beam of (a) 1m length (b) 1m width (c) 1m (d) None of these

Last Answer : (b) 1m width

The maximum deflection of a simply supported beam of span L, carrying an isolated load at the centre of the span; flexural rigidity being EI, is (A) WL3 /3EL (B) WL3 /8EL (C) WL3 /24EL (D) WL3 /48EL

Description : The maximum deflection of a simply supported beam of span L, carrying an isolated load at the  centre of the span; flexural rigidity being EI, is  (A) WL3 /3EL (B) WL3 /8EL (C) WL3 /24EL (D) WL3 /48EL

Last Answer : (D) WL3 /48EL

When a series of wheel loads crosses a simply supported girder, the maximum bending moment under any given wheel load occurs when (A) The centre of gravity of the load system is midway between the centre of span and wheel load under consideration (B) The centre of span is midway between the centre of gravity of the load system and the wheel load under consideration (C) The wheel load under consideration is midway between the centre of span and the centre of gravity of the load system (D) None of the above

Description : When a series of wheel loads crosses a simply supported girder, the maximum bending moment under any given wheel load occurs when (A) The centre of gravity of the load system is midway between the centre of ... the centre of span and the centre of gravity of the load system (D) None of the above

Last Answer : (B) The centre of span is midway between the centre of gravity of the load system and the wheel load under consideration

The maximum bending moment due to a train of wheel loads on a simply supported girder (A) Always occurs at centre of span (B) Always occurs under a wheel load (C) Never occurs under a wheel load (D) None of the above

Description : The maximum bending moment due to a train of wheel loads on a simply supported girder (A) Always occurs at centre of span (B) Always occurs under a wheel load (C) Never occurs under a wheel load (D) None of the above

Last Answer : (B) Always occurs under a wheel load

A simply supported beam of span carries a uniformly distributed load . The maximum bending moment is (A) WL/2 (B) WL/4 (C) WL/8 (D) WL/12

Description : A simply supported beam of span carries a uniformly distributed load . The maximum bending moment is (A) WL/2 (B) WL/4 (C) WL/8 (D) WL/12

Last Answer : (C) WL/8

A simply supported beam of span L carries a concentrated load W at its mid-span. The maximum bending moment M is (A) WL/2 (B) WL/4 (C) WL/8 (D) WL/12

Description : A simply supported beam of span L carries a concentrated load W at its mid-span. The maximum  bending moment M is  (A) WL/2  (B) WL/4  (C) WL/8  (D) WL/12

Last Answer : (B) WL/4

The maximum deflection of (A) A simply supported beam carrying a uniformly increasing load from either end and having the apex at the mid span is WL3 /60EI (B) A fixed ended beam carrying a distributed load over the span is WL3 /384EI (C) A fixed ended beam carrying a concentrated load at the mid span is WL3 /192EI (D) All the above

Description : The maximum deflection of  (A) A simply supported beam carrying a uniformly increasing load from either end and having  the apex at the mid span is WL3 /60EI (B) A fixed ended beam ... ended beam carrying a concentrated load at the mid span is WL3 /192EI (D) All the above 

Last Answer : (D) All the above 

The maximum bending moment due to a moving load on a simply supported beam, occurs (A) At the mid span (B) At the supports (C) Under the load (D) Anywhere on the beam

Description : The maximum bending moment due to a moving load on a simply supported beam, occurs (A) At the mid span (B) At the supports (C) Under the load (D) Anywhere on the beam

Last Answer : (C) Under the load

Maximum deflection of a (A) Cantilever beam carrying a concentrated load W at its free end is WL3 /3EI (B) Simply supported beam carrying a concentrated load W at mid-span is WL3 /48EI (C) Cantilever beam, carrying a uniformly distributed load over span is WL3 /8EI (D) All the above

Description : Maximum deflection of a (A) Cantilever beam carrying a concentrated load W at its free end is WL3 /3EI (B) Simply supported beam carrying a concentrated load W at mid-span is WL3 /48EI (C) Cantilever beam, carrying a uniformly distributed load over span is WL3 /8EI (D) All the above

Last Answer : (D) All the above

If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm(C) 150 cm (D) 200 cm

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm (C) 150 cm (D) 200 cm

Last Answer : Answer: Option C

If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Last Answer : Answer: Option C

If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Description : If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Last Answer : Answer: Option C

Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to resist a sagging bending moment near mid-span. (c) When the slab is built into a brick or masonry wall the slab should be designed to resist a hogging moment at the face of the support. (d) All of the above.

Description : Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to ... be designed to resist a hogging moment at the face of the support. (d) All of the above.

Last Answer : (d) All of the above.