Why is the span length ratio of end span/approach span to its neighboring inner spans usually about 0.75?

Why is the span length ratio of end span/approach span to its neighboring inner spans usually about 0.75?
by

1 Answer

Answer :

From aesthetic point of view, an odd number of spans with a decrease in length in the direction of abutment is desirable. Moreover, spans of equal length are found to be boring. However, the arrangement of irregular span lengths is not recommended because it gives a feeling of uneasiness.

From structural point of view, for a multi­span bridge with equal span length, the sagging moment at the mid­span of the end span/approach span is largest. In order to reduce this moment, the span length of end span/approach span is designed to be 0.75 of inner spans. However, this ratio should not be less than 0.40 because of the effect of uplifting at the end span/approach span support.
Note: End span refers to the last span in a continuous bridge while approach span refers top the first span of a bridge.
by

Related questions

In the construction of a two­span bridge (span length = L) by using span­by­span construction, why is a length of about 1.25L bridge segment is constructed in the first phase of construction?

Description : In the construction of a two­span bridge (span length = L) by using span­by­span construction, why is a length of about 1.25L bridge segment is constructed in the first phase of construction?

Last Answer : Basically, there are mainly three reasons for this arrangement: (i) The permanent structure is a statically indeterminate structure. During construction by using span­by­span construction, if the ... 25L from the first pier where there is relatively more space to accommodate prestressing works.

Under what situation shall engineers use jacking at one end only and from both ends in prestressing work?

Description : Under what situation shall engineers use jacking at one end only and from both ends in prestressing work?

Last Answer : During prestressing operation at one end, frictional losses will occur and the prestressing force decreases along the length of tendon until reaching the other end. These frictional losses include the ... if the total span length is sufficiently long, jacking from both ends should be considered.

What is sucker deck principle for variable depth bridge decks?

Description : What is sucker deck principle for variable depth bridge decks?

Last Answer : For a variable depth bridge deck, the depth of continuous multi­span bridge deck is increased in pier supports and this absorbs sagging moments in the ... of arches and curved soffit rather than boring uniform deck alignment. Reference is made to Brian Pritchard (1992).

How do engineer determine the number of cells for concrete box girder bridges?

Description : How do engineer determine the number of cells for concrete box girder bridges?

Last Answer : If the depth of a box girder bridge exceeds 1/6 or 1/5 of the bridge width, then it is recommended to be designed as a single cell box girder bridge. However, if the bridge depth is ... improvement in transverse load distribution when the number of cells of box girder is increased to three or more.

Should raking piles of a bridge abutment be placed under an embankment?

Description : Should raking piles of a bridge abutment be placed under an embankment?

Last Answer : For a bridge abutment to be supported on raking piles with different orientations, the movement between the ground and the pile group is difficult to predict. For instance, if some of the raking ... experience severe bending moment and damage the piles as recommended by Dr. Edmund C Hambly (1979).

Polytetrafluoroethylene (PTFE) is commonly used in sliding bearings. Why?

Description : Polytetrafluoroethylene (PTFE) is commonly used in sliding bearings. Why?

Last Answer : The choice of sliding surface of bearings is of vital importance because the sliding surfaces generate frictional forces which are exerted on the bearings and substructure of the bridge. For ... be designed with dimples to avoid the lubricant from squeezing out under repeated translation movements.

What are the shortcomings of grillage analysis which is commonly used in structural analysis of bridges?

Description : What are the shortcomings of grillage analysis which is commonly used in structural analysis of bridges?

Last Answer : Grillage analysis suffers from the following shortcomings based on E. C. Hambly: (i) For coarse mesh, torques may not be identical in orthogonal directions. Similarly, twists may differ in ... moment in an element depends on the curvatures in the beam's direction and its orthogonal direction.

Under what situation should engineers use pot bearings instead of elastomeric bearings?

Description : Under what situation should engineers use pot bearings instead of elastomeric bearings?

Last Answer : In the event of high vertical loads combined with large angle of rotations, rubber bearings are undesirable when compared with pot bearings. For instance, elastomeric ... bearings are better alternatives than elastomeric bearings in such an scenario as suggested by David J. Lee.

In joints of precast concrete bridge segments, what are the functions of applying epoxy adhesive?

Description : In joints of precast concrete bridge segments, what are the functions of applying epoxy adhesive?

Last Answer : Epoxy adhesive is applied in these joints for the following purposes according to International Road Federation (1977): (i) It seals up the joints completely between precast concrete segments to protect the ... in transferring of shear between the joints in case a large single shear key is used.

What are the functions of grout inside tendon ducts?

Description : What are the functions of grout inside tendon ducts?

Last Answer : Grout in prestressing works serves the following purposes: (i) Protect the tendon against corrosion. (ii) Improve the ultimate capacity of tendon. (iii) Provide a bond between the structural member and the tendon. (iv) In case of failure, the anchorage is not subject to all strain energy.

In the design of a simply supported skew bridge, which direction of reinforcement should be provided?

Description : In the design of a simply supported skew bridge, which direction of reinforcement should be provided?

Last Answer : In the conventional design of steel reinforcement for a simply supported skew bridge, a set of reinforcement is usually placed parallel to free edge while the other set is designed parallel ... ). In this way, considerable savings would be obtained from the orthogonal arrangement of reinforcement.

What are the three major types of reinforcement used in prestressing?

Description : What are the three major types of reinforcement used in prestressing?

Last Answer : i) Spalling reinforcement Spalling stresses are established behind the loaded area of anchor blocks and this causes breaking away of surface concrete. These stresses are induced by strain incompatibility with ... of action of the load. Reinforcement is needed to resist these lateral tensile forces.

What is the advantage of sliding bearings over roller bearings?

Description : What is the advantage of sliding bearings over roller bearings?

Last Answer : In roller bearing for a given movement the roller bearing exhibit a change in pressure centre from its original position by one­half of its movement based on David J. Lee. However, with sliding ... built in the substructure. It follows that there is no change in pressure center after the movement.

Are diaphragms necessary in the design of concrete box girder bridges?

Description : Are diaphragms necessary in the design of concrete box girder bridges?

Last Answer : Diaphragms are adopted in concrete box girder bridges to transfer loads from bridge decks to bearings. Since the depth of diaphragms normally exceeds the width by two times, they are usually designed ... In fact, diaphragms also contribute to the provision of torsional restraint to the bridge deck.

In a curved prestressed bridge, how should the guided bearings in piers of the curved region be oriented with respect to the fixed bearing in abutment?

Description : In a curved prestressed bridge, how should the guided bearings in piers of the curved region be oriented with respect to the fixed bearing in abutment?

Last Answer : To determine the orientation of guided bearings, one should understand the movement of curved region of a prestressed bridge. Movement of prestress and creep are tangential to the curvature of the ... large, temporary freedom of movement at the guided bearings has to be provided during construction.

How to determine the size of elastomeric bearings?

Description : How to determine the size of elastomeric bearings?

Last Answer : For elastomeric bearing, the vertical load is resisted by its compression while shear resistance of the bearing controls the horizontal movements. The design ... and fatigue damage. The vertical stiffness of bearings is obtained by inserting sufficient number of steel plates.

In the design of elastomeric bearings, why are steel plates inserted inside the bearings?

Description : In the design of elastomeric bearings, why are steel plates inserted inside the bearings?

Last Answer : For elastomeric bearing to function as a soft spring, the bearing should be allowed for bulging laterally and the compression stiffness can be increased by limiting the amount of lateral bulging. To ... , the presence of metal plates does not affect the shear stiffness of the elastomeric bearings.

In prestressing work, if more than one wire or strand is included in the same duct, why should all wires/strands be stressed at the same time?

Description : In prestressing work, if more than one wire or strand is included in the same duct, why should all wires/strands be stressed at the same time?

Last Answer : If wires/strands are stressed individually inside the same duct, then those stressed strand/wires will bear against those unstressed ones and trap them. Therefore, the friction of the trapped wires is high and is undesirable.

Sometimes the side of concrete bridges is observed to turn black in colour. What is the reason for this phenomenon?

Description : Sometimes the side of concrete bridges is observed to turn black in colour. What is the reason for this phenomenon?

Last Answer : In some cases, it may be due to the accumulation of dust and dirt. However, for the majority of such phenomenon, it is due to fungus or algae growth on concrete bridges. After rainfall, the ... help to solve this problem. Reference is made to Sandberg Consulting Engineers Report 18380/X/01.

What are the advantages of assigning the central pier and the abutment as fixed piers?

Description : What are the advantages of assigning the central pier and the abutment as fixed piers?

Last Answer : (i) For abutment pier to be assigned as fixed pier while the bridge is quite long, the longitudinal loads due to earthquake are quite large. As the earthquake loads are resisted by fixed piers, the size of ... Therefore, the size of movement joints can be reduced significantly.

In bridge widening projects, the method of stitching is normally employed for connecting existing deck to the new deck. What are the problems associated with this method in terms of shrinkage of concrete?

Description : In bridge widening projects, the method of stitching is normally employed for connecting existing deck to the new deck. What are the problems associated with this method in terms of shrinkage of concrete?

Last Answer : In the method of stitching, it is a normal practice to construct the widening part of the bridge at first and let it stay undisturbed for several months. After that, concreting will then be ... Stitching refers to formation of a segment of bridge deck between an existing bridge and a new bridge.

In incremental launching method of bridge construction, what are the measures adopted to enhance sufficient resistance of the superstructure during the launching process?

Description : In incremental launching method of bridge construction, what are the measures adopted to enhance sufficient resistance of the superstructure during the launching process?

Last Answer : i) During the launching process the leading edge of the superstructure is subject to a large hogging moment. In this connection, steel launching nose typically about 0.6­0.65 times span length is ... . iii)For very long span bridge, temporary piers are provided to limit the cantilever moment.

What is “preset” during installation of bridge bearings?

Description : What is “preset” during installation of bridge bearings?

Last Answer : Preset is a method to reduce the size of upper plates of sliding bearings in order to save the material cost. The normal length of a upper bearing plate should be composed of the ... of a certain distance of sliding bearings with respect to upper bearing plates during installation of bearings.

When the slab is supported on all the four edges and the ratio of long span to short span is small, bending takes place along both the spans, such a slab is known as (a) Slab spanning in one direction (b) One way slab. (c) Slab spanning in two direction. (d) Two-way slab.

Description : When the slab is supported on all the four edges and the ratio of long span to short span is small, bending takes place along both the spans, such a slab is known as (a) Slab spanning in one direction (b) One way slab. (c) Slab spanning in two direction. (d) Two-way slab.

Last Answer : (d) Two-way slab.

The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6

Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6

Last Answer : Answer: Option C

The three moments equation is applicable only when (A) The beam is prismatic (B) There is no settlement of supports (C) There is no discontinuity such as hinges within the span (D) The spans are equal

Description : The three moments equation is applicable only when (A) The beam is prismatic (B) There is no settlement of supports (C) There is no discontinuity such as hinges within the span (D) The spans are equal

Last Answer : (C) There is no discontinuity such as hinges within the span

Basic values of span/effective depth ratios to be used for beams and slabs with spans [ A ] Less than 10m [ B ] Less than 20 m [ C ] 10 m- 20 m [ D ] More than 20 m

Description : Basic values of span/effective depth ratios to be used for beams and slabs with spans [ A ] Less than 10m [ B ] Less than 20 m [ C ] 10 m- 20 m [ D ] More than 20 m

Last Answer : [ A ] Less than 10m

For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9

Description : For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9

Last Answer : Answer: Option D

The date of painting of steel work should be painted in white on the out side of the left girder a) of the 1st span only b) first span only but on all spans for Imp. Bridges* c) of the all spans d) None of the above

Description : The date of painting of steel work should be painted in white on the out side of the left girder a) of the 1st span only b) first span only but on all spans for Imp. Bridges* c) of the all spans d) None of the above

Last Answer : b) first span only but on all spans for Imp. Bridges*

If the length of an intermediate span of a continuous slab is 5m, the length of the end span is kept (A) 4.5 m (B) 4.0 m (C) 3.5 m (D) 3.0 m

Description : If the length of an intermediate span of a continuous slab is 5m, the length of the end span is kept (A) 4.5 m (B) 4.0 m (C) 3.5 m (D) 3.0 m

Last Answer : Answer: Option A

The CRS sanction is required in the ROB project for construction of a) Approach spans b) Laying road c) Railway spans d) none

Description : The CRS sanction is required in the ROB project for construction of a) Approach spans b) Laying road c) Railway spans d) none

Last Answer : c) Railway span

The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6

Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6

Last Answer : (c) 0.9

When a slab is continuous over several spans, negative (i.e. hogging ) bending moment is induced over the (a) End supports (b) Intermediate supports (c) Both (a) & (b) (d) Non of the

Description : When a slab is continuous over several spans, negative (i.e. hogging ) bending moment is induced over the (a) End supports (b) Intermediate supports (c) Both (a) & (b) (d) Non of the

Last Answer : (b) Intermediate supports

An R.C.C. roof slab is designed as a two way slab if (A) It supports live loads in both directions (B) The ratio of spans in two directions is less than 2 (C) The slab is continuous over two supports (D) The slab is discontinuous at edges

Description : An R.C.C. roof slab is designed as a two way slab if (A) It supports live loads in both directions (B) The ratio of spans in two directions is less than 2 (C) The slab is continuous over two supports (D) The slab is discontinuous at edges

Last Answer : Answer: Option B

If l1 and l2 are the lengths of long and short spans of a two way slab simply supported on four edges and carrying a load w per unit area, the ratio of the loads split into w1 and w2acting on strips parallel to l2 and l1 is (A) w1/w2 = l2/l1 (B) w1/w2 = (l2/l1)² (C) w1/w2 = (l2/l1)3 (D) w1/w2 = (l2/l1)

Description : If l1 and l2 are the lengths of long and short spans of a two way slab simply supported on four edges and carrying a load w per unit area, the ratio of the loads split into w1 and w2acting on strips parallel to l2 and l1 is (A) ... l1 (B) w1/w2 = (l2/l1)² (C) w1/w2 = (l2/l1)3 (D) w1/w2 = (l2/l1)

Last Answer : Answer: Option D

If the ratio of long and short spans of a two way slab with corners held down is r, the actual reduction of B.M. is given by (A) (5/6) (r/1 + r²) M (B) (5/6) (r²/1 + r²) M (C) (5/6) (r²/1 + r3 ) M (D) (5/6) (r²/1 + r4 ) M

Description : If the ratio of long and short spans of a two way slab with corners held down is r, the actual reduction of B.M. is given by (A) (5/6) (r/1 + r²) M (B) (5/6) (r²/1 + r²) M (C) (5/6) (r²/1 + r3 ) M (D) (5/6) (r²/1 + r4 ) M

Last Answer : Answer: Option D

The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these

Description : The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these

Last Answer : Answer: Option B

In a counterfort retaining wall, the main reinforcement in the stem at mid span is provided on (A) Front face only (B) Inner face only (C) Both front face and inner face (D) None of the above

Description : In a counterfort retaining wall, the main reinforcement in the stem at mid span is provided on (A) Front face only (B) Inner face only (C) Both front face and inner face (D) None of the above

Last Answer : Answer: Option A

The effective span of a simply supported slab is (a) Distance between the centers of the bearings (b) Clear distance between the inner faces of the walls plus twice he thickness of the slab. (c) Cleat spa plus effective depth of the slab. (d) All the above

Description : The effective span of a simply supported slab is (a) Distance between the centers of the bearings (b) Clear distance between the inner faces of the walls plus twice he thickness of the slab. (c) Cleat spa plus effective depth of the slab. (d) All the above

Last Answer : (c) Cleat spa plus effective depth of the slab.

A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 × 106 N/mm2 , the depth of the joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm

Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so  that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the  value of E = 0.2 ... joist, is  (A) 200 mm  (B) 250 mm  (C) 300 mm  (D) 400 mm 

Last Answer : (D) 400 mm 

A three hinged parabolic arch hinged at the crown and springing, has a horizontal span of 4.8 m and a central rise of 1 m. It carries a uniformly distributed load of 0.75 tonne per metre over half left hand span. The horizontal thrust at the support will be (A) 10.8 tonnes (B) 1.08 tonnes (C) 1.8 tonnes (D) 0.8 tonnes

Description : A three hinged parabolic arch hinged at the crown and springing, has a horizontal span of 4.8 m  and a central rise of 1 m. It carries a uniformly distributed load of 0.75 tonne per metre over half  left hand span ... A) 10.8 tonnes  (B) 1.08 tonnes  (C) 1.8 tonnes  (D) 0.8 tonnes 

Last Answer : (B) 1.08 tonnes 

The ratio of the length and diameter of a simply supported uniform circular beam which experiences maximum bending stress equal to tensile stress due to same load at its mid span, is (A) 1/8 (B) 1/4 (C) 1/2 (D) 1/3

Description : The ratio of the length and diameter of a simply supported uniform circular beam which  experiences maximum bending stress equal to tensile stress due to same load at its mid span, is  (A) 1/8  (B) 1/4  (C) 1/2  (D) 1/3 

Last Answer : (C) 1/2 

The ratio of the length and depth of a simply supported rectangular beam which experiences maximum bending stress equal to tensile stress, due to same load at its mid span, is (A) 1/2 (B) 2/3 (C) 1/4 (D) 1/3

Description : The ratio of the length and depth of a simply supported rectangular beam which experiences  maximum bending stress equal to tensile stress, due to same load at its mid span, is  (A) 1/2  (B) 2/3  (C) 1/4  (D) 1/3

Last Answer : (B) 2/3 

A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated load W at its mid-span. The same bar experiences an extension e under same tensile load. The ratio of the maximum deflection to the elongation, is (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Description : A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated  load W at its mid-span. The same bar experiences an extension e under same tensile load. The  ratio of the maximum deflection to the ... (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Last Answer : (C) (L/2d)

The general expression for the B.M. of a beam of length l is the beam carries M = (wl/2) x - (wx²/2) (A) A uniformly distributed load w/unit length (B) A load varying linearly from zero at one end to w at the other end (C) An isolated load at mid span (D) None of these

Description : The general expression for the B.M. of a beam of length l is the beam carries M = (wl/2) x - (wx²/2)  (A) A uniformly distributed load w/unit length  (B) A load varying linearly from zero at one end to w at the other end  (C) An isolated load at mid span  (D) None of these 

Last Answer : (A) A uniformly distributed load w/unit length 

While using three moments equation, a fixed end of a continuous beam is replaced by an additional span of (A) Zero length (B) Infinite length (C) Zero moment of inertia(D) None of the above

Description : While using three moments equation, a fixed end of a continuous beam is replaced by an additional span of (A) Zero length (B) Infinite length (C) Zero moment of inertia (D) None of the above

Last Answer : (A) Zero length

If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Last Answer : Answer: Option C

A uniformly distributed load (w) of length shorter than the span crosses a girder. The bending moment at a section in the girder will be maximum when (a) Head of the load is at the section (b) Tail of the load is at the section (c) Section divides the load in the same ratio as it divides the span (d) Section divides the load in two equal lengths.

Description : A uniformly distributed load (w) of length shorter than the span crosses a girder. The bending moment at a section in the girder will be maximum when (a) Head of the load is at the section (b) Tail ... load in the same ratio as it divides the span (d) Section divides the load in two equal lengths.

Last Answer : (c) Section divides the load in the same ratio as it divides the span

India's land border with the neighboring countries is, in length, approximately (a) 8 thousand km (b) 15 thousand km (c) 10 thousand km (d) 16 thousand km

Description : India's land border with the neighboring countries is, in length, approximately (a) 8 thousand km (b) 15 thousand km (c) 10 thousand km (d) 16 thousand km

Last Answer : Ans: (c)

The ratio of the deflections of the free end of a cantilever due to an isolated load at 1/3rd and 2/3rd of the span, is (A) 1/7 (B) 2/7 (C) 3/7 (D) 2/5

Description : The ratio of the deflections of the free end of a cantilever due to an isolated load at 1/3rd and  2/3rd of the span, is  (A) 1/7  (B) 2/7  (C) 3/7  (D) 2/5 

Last Answer : (B) 2/7