Description : A reinforcing slab, build monolithically with the supporting columns and is reinforced in two or more directions, without any provision of beams is called a (a) Two way slab (b) Flat slab (c) Continus slab (d) Cireulashion
Last Answer : (b) Flat slab
Description : A flat slab is supported (A) On beams (B) On columns (C) On beams and columns (D) On columns monolithically built with slab
Last Answer : Answer: Option D
Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6
Last Answer : Answer: Option C
Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6
Last Answer : (c) 0.9
Description : The slab is said to be orthotropically reinforced , when the reinforcement is arranged in; [ A ] Single direction [ B ] Two directions at right angles with equal meshes [ C ] Two directions at right angles with unequal meshes [ D ] At the corners only
Last Answer : [ C ] Two directions at right angles with unequal meshes
Description : A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter
Last Answer : (b) 8 mm diameter
Description : The purpose of lateral ties in short reinforced concrete columns is to [ A ] Facilitate construction [ B ] Facilitate compaction of concrete [ C ] Increase the load carrying capacity of the columns [ D ] Avoid buckling of longitudinal bars
Last Answer : [ D ] Avoid buckling of longitudinal bars
Description : In a simply supported reinforced concrete beam, the reinforcement is placed. (a) Above the neutral axis (b) Below the neutral axis (c) At the neutral axis (d) None of these
Last Answer : (b) Below the neutral axis
Description : In flat roof of reinforced cement concrete, the recommended angle of slope, is (A) Zero (B) A few degrees (C) 10° (D) 200
Last Answer : Answer: Option B
Description : In a singly reinforced beam, if the stress in concrete reaches its allowable limit later than the steel reaches, its permissible value, the beam section is said to be (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section
Last Answer : (b) Over-reinforced section
Description : To develop complete yield line pattern the slab must be [ A ] Under reinforced [ B ] Over reinforced [ C ] Both (a) and (b) [ D ] None of the above.
Last Answer : [ A ] Under reinforced
Description : It is preferable, that the design of slab should result in [ A ] A balanced section [ B ] An under reinforced section [ C ] Over reinforced section [ D ] None of the above.
Last Answer : [ B ] An under reinforced section
Description : When the slab is supported on all the four edges and the ratio of long span to short span is small, bending takes place along both the spans, such a slab is known as (a) Slab spanning in one direction (b) One way slab. (c) Slab spanning in two direction. (d) Two-way slab.
Last Answer : (d) Two-way slab.
Description : In a singly reinforced concrete beam, as the load increases. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete and steel will resist tension. (d) Both concrete and steel will resist compression.
Last Answer : (b) Only steel bars will resist tension.
Description : In a singly reinforced concrete beam, if the load is vey small. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete & steel will resist tension. (d) Both concrete & steel will resist compression.
Last Answer : (c) Both concrete & steel will resist tension.
Description : Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of ... ) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column
Description : Pick up the correct statement from the following: (A) The roof slabs of multi-storeyed buildings are constructed monolithically to carry the various floor loads (B) The beams of multi-storeyed ... slab is spanned across the secondary beams provided between the main beams (D) All of these
Description : Distribution reinforcement in a simply supported slab, is provided to distribute (A) Load (B) Temperature stress (C) Shrinkage stress (D) All the above
Description : If K is a constant depending upon the ratio of the width of the slab to its effective span l, x is the distance of the concentrated load from the nearer support, bw is the width of the area of contact of the concentrated load measured ... ) Kx (1 - x/l) + bw (C) Kx (1 + x/l) + bw (D) All the above
Description : If the sides of a slab simply supported on edges and spanning in two directions are equal, the maximum bending moment is multiplied by (A) 0.2 (B) 0.3 (C) 0.4 (D) 0.5
Description : The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these
Description : For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9
Description : If l1 and l2 are the lengths of long and short spans of a two way slab simply supported on four edges and carrying a load w per unit area, the ratio of the loads split into w1 and w2acting on strips parallel to l2 and l1 is (A) ... l1 (B) w1/w2 = (l2/l1)² (C) w1/w2 = (l2/l1)3 (D) w1/w2 = (l2/l1)
Description : The maximum ratio of span to depth of a slab simply supported and spanning in two directions, is (A) 25 (B) 30 (C) 35 (D) 40
Description : Design of a two way slab simply supported on edges and having no provision to prevent the corners from lifting, is made by (A) Rankine formula (B) Marcus formula (C) Rankine Grashoff formula (D) Grashoff formula
Description : The pitch of the main bars in a simply supported slab, should not exceed its effective depth by (A) Three times (B) Four times (C) Five times (D) Six times
Description : In a simply supported slab, alternate bars are curtailed at (A) 1/4th of the span (B) 1/5th of the span (C) 1/6th of the span (D) 1/7th of the span
Description : The maximum ratio of span to depth of a slab simply supported and spanning in one direction, is (A) 35 (B) 25 (C) 30 (D) 20
Description : For a slab supported on its four edges with corners held down and loaded uniformly, the Marcus correction factor to the moments obtained by Grashoff Rankine's theory (A) Is always less than 1 (B) Is always greater than 1 (C) Can be more than 1 (D) Can be less than 1
Last Answer : Answer: Option A
Description : The maximum ratio of span to depth of a slab simple supported and spanning in two directions, is (a) 25 (b) 30 (c) 35 (d) 40
Last Answer : (c) 35
Description : The maximum ratio of span to depth of a slab simply supported and spanning in one direction is (a) 35 (b) 25 (c) 30 (d) 20
Last Answer : (c) 30
Description : The effective span of a simply supported slab is (a) Distance between the centers of the bearings (b) Clear distance between the inner faces of the walls plus twice he thickness of the slab. (c) Cleat spa plus effective depth of the slab. (d) All the above
Last Answer : (c) Cleat spa plus effective depth of the slab.
Description : In a simply supported slab, alternate bars are curtailed at (a) 1/4th of the span (b) 1/5th of the span (c) 1/6th of the span (d) 1/7th of the span
Last Answer : (d) 1/7th of the span
Description : If the sides o a slab simply supported on its edges and spanning in two way are equal, then the maximum bending moment is multiplied by. (a) 0.25 (b) 0.50 (c) 0.75 (d) 0.85
Last Answer : (b) 0.50
Description : A slab simply supported on the four edges, with corners not held down and carrying uniformly distributed load, is used in (a) Singly storeyed buildings. (b) Double storeyed buildings. (c) Multi storeyed buildings (d) All the above
Last Answer : (a) Singly storeyed buildings.
Description : A two way slab (a) May be simply supported on the four edges, with comers not held down and carrying uniformly distributed load. (b) May be simply supported on the four edge , with corners held ... . (c) May have edges fixed or continuous and carrying uniformly distributed load. (d) All the above.
Last Answer : (d) All the above.
Description : The clear cover in a simply supported slab should not be less than the diameter of the reinforcing bar (a) Correct (b) Incorrect’ (c) Not known (d) None of these
Last Answer : (a) Correct
Description : in a simply supported slab, the pitch of distribution reinforcement should not be more than_____________the effective depth of slab or 60cm which ever is smaller. (a) Double (b) Three times (c) Five times (d) Six times
Last Answer : (c) Five times
Description : The span/over all depth ratio for a simply supported two-way slab according to IS : 456- 2000 is given by [ A ] 20 [ B ] 28 [ C ] 32 [ D ] 40
Last Answer : [ B ] 28
Description : Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii
Last Answer : [ A ] i
Description : In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile
Description : For a wall carrying heavy load on low bearing capacity soil, (A) Lean concrete bed is provided (B) Thick concrete bed is provided (C) Reinforced concrete bed is provided (D) Both (a) and (c) of the above
Description : In an over-reinforced section (a) Steel reinforcement is not fully stressed to its permissible value (b) Concrete is not fully stressed to its permissible value (c) Either (a) and (b) (d) Both (a) and (b)
Last Answer : (a) Steel reinforcement is not fully stressed to its permissible value
Description : The moment of resistance of an under- reinforced section is computer on the basis of (a) Compressive force developed in concrete (b) Tensile force developed in steel (c) Both (a) & (b) (d) All the above
Last Answer : (b) Tensile force developed in steel
Description : The foundation which consists of a thick reinforced cement slab covering whole area to support heavy concentrated structural loads, is known as (A) Combined footing (B) Strap footing (C) Raft footing (D) None of these
Last Answer : Option C
Description : To prevent compressive stresses in a rigid concrete pavement, the joint provided, is (A) Expansion joint (B) Contraction joint (C) Hinged joint (D) All the above
Description : Pick up the incorrect statement from the following: (A) Horizontal D.P.C. is provided at plinth level in internal walls (B) D.P.C. is provided under door and verandah openings (C) Vertical D.P.C. is not provided in internal walls (D) Cement concrete is a rigid damp-proofing material
Description : If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span ... (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²
Description : The effective width of a column strip of a flat slab, is (A) One-fourth the width of the panel (B) Half the width of the panel (C) Radius of the column (D) Diameter of the column
Description : Thickened part of a flat slab over its supporting column, is technically known as (A) Drop panel (B) Capital (C) Column head (D) None of these