The effective width of a column strip of a flat slab, is (A) One-fourth the width of the panel (B) Half the width of the panel (C) Radius of the column (D) Diameter of the column

The effective width of a column strip of a flat slab, is
(A) One-fourth the width of the panel
(B) Half the width of the panel
(C) Radius of the column
(D) Diameter of the column
by

1 Answer

Answer :

Answer: Option B
by

Related questions

If the size of panel in a flat slab is 6 m × 6 m, then as per Indian Standard Code, the widths of column strip and middle strip are (A) 3.0 m and 1.5 m (B) 1.5 m and 3.0 m (C) 3.0 m and 3.0 m (D) 1.5 m and 1.5m

Description : If the size of panel in a flat slab is 6 m × 6 m, then as per Indian Standard Code, the widths of column strip and middle strip are (A) 3.0 m and 1.5 m (B) 1.5 m and 3.0 m (C) 3.0 m and 3.0 m (D) 1.5 m and 1.5 m

Last Answer : Answer: Option C

According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is (A) Half of the width of the slab (B) Two-third of the width of the slab (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Description : According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is ... (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Last Answer : Answer: Option C

If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than (A) WL/12 (L - 2D/3)² (B) WL/10 (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Description : If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span ... (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Last Answer : Answer: Option C

Critical section for shear in case of flat slabs is at a distance of (A) Effective depth of slab from periphery of column/drop panel (B) d/2 from periphery of column/capital/ drop panel (C) At the drop panel of slab (D) At the periphery of column

Description : Critical section for shear in case of flat slabs is at a distance of (A) Effective depth of slab from periphery of column/drop panel (B) d/2 from periphery of column/capital/ drop panel (C) At the drop panel of slab (D) At the periphery of column

Last Answer : Answer: Option B

Thickened part of a flat slab over its supporting column, is technically known as (A) Drop panel (B) Capital (C) Column head (D) None of these

Description : Thickened part of a flat slab over its supporting column, is technically known as (A) Drop panel (B) Capital (C) Column head (D) None of these

Last Answer : Answer: Option A

Enlarged head of a supporting column of a flat slab is technically known as (A) Supporting end of the column (B) Top of the column (C) Capital (D) Drop panel

Description : Enlarged head of a supporting column of a flat slab is technically known as (A) Supporting end of the column (B) Top of the column (C) Capital (D) Drop panel

Last Answer : Answer: Option C

The thickness of base slab of a retaining wall generally provided, is (A) One half of the width of the stem at the bottom (B) One-third of the width of the stem at the bottom (C) One fourth of the width of the steam at the bottom (D) Width of the stem at the bottom

Description : The thickness of base slab of a retaining wall generally provided, is (A) One half of the width of the stem at the bottom (B) One-third of the width of the stem at the bottom (C) One fourth of the width of the steam at the bottom (D) Width of the stem at the bottom

Last Answer : Answer: Option D

The diameter of the column head support a flat slab, is generally kept (A) 0.25 times the span length (B) 0.25 times the diameter of the column (C) 4.0 cm larger than the diameter of the column (D) 5.0 cm larger than the diameter of the column

Description : The diameter of the column head support a flat slab, is generally kept (A) 0.25 times the span length (B) 0.25 times the diameter of the column (C) 4.0 cm larger than the diameter of the column (D) 5.0 cm larger than the diameter of the column

Last Answer : Option A

The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Description : The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Last Answer : [ C ] One-eighth

The width of the flange of a L-beam, should be less than (A) One-sixth of the effective span (B) Breadth of the rib + four times thickness of the slab (C) Breadth of the rib + half clear distance between ribs (D) Least of the above

Description : The width of the flange of a L-beam, should be less than (A) One-sixth of the effective span (B) Breadth of the rib + four times thickness of the slab (C) Breadth of the rib + half clear distance between ribs (D) Least of the above

Last Answer : Answer: Option D

According to IS:456, the diameter of the helices in circular a column shall be at least [ A ] The diameter of longitudinal steel [ B ] One-half the diameter of longitudinal steel [ C ] One-fourth the diameter of longitudinal steel [ D ] Three-fourth the diameter of longitudinal steel

Description : According to IS:456, the diameter of the helices in circular a column shall be at least [ A ] The diameter of longitudinal steel [ B ] One-half the diameter of longitudinal steel [ C ] One-fourth the diameter of longitudinal steel [ D ] Three-fourth the diameter of longitudinal steel

Last Answer : [ C ] One-fourth the diameter of longitudinal steel

The diameter of the Links in column should be at least……….of the largest diameter of the longitudinal steel [ A ] One-half [ B ] Three-fourth [ C ] One eighth [ D ] One – fourth

Description : The diameter of the Links in column should be at least……….of the largest diameter of the longitudinal steel [ A ] One-half [ B ] Three-fourth [ C ] One eighth [ D ] One – fourth

Last Answer : [ D ] One – fourth

If K is a constant depending upon the ratio of the width of the slab to its effective span l, x is the distance of the concentrated load from the nearer support, bw is the width of the area of contact of the concentrated load measured parallel to the supported edge, the effective width of the slab be is (A) K/x (1 + x/d) + bw (B) Kx (1 - x/l) + bw (C) Kx (1 + x/l) + bw (D) All the above

Description : If K is a constant depending upon the ratio of the width of the slab to its effective span l, x is the distance of the concentrated load from the nearer support, bw is the width of the area of contact of the concentrated load measured ... ) Kx (1 - x/l) + bw (C) Kx (1 + x/l) + bw (D) All the above

Last Answer : Answer: Option B

The width of the flange of a T-beam should be less than (A) One-third of the effective span of the T-beam (B) Distance between the centres of T-beam (C) Breadth of the rib plus twelve times the thickness of the slab (D) Least of the above

Description : The width of the flange of a T-beam should be less than (A) One-third of the effective span of the T-beam (B) Distance between the centres of T-beam (C) Breadth of the rib plus twelve times the thickness of the slab (D) Least of the above

Last Answer : Answer: Option D

If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Description : If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Last Answer : Answer: Option C

The diameter of ties in a column should be (A) More than or equal to one fourth of diameter of main bar (B) More than or equal to 5 mm (C) More than 5 mm but less than one-fourth of diameter of main bar (D) More than 5 mm and also more than one-fourth of diameter of main bar

Description : The diameter of ties in a column should be (A) More than or equal to one fourth of diameter of main bar (B) More than or equal to 5 mm (C) More than 5 mm but less than one-fourth of diameter of main bar (D) More than 5 mm and also more than one-fourth of diameter of main bar

Last Answer : Answer: Option D

A foundation is called shallow if its depth, is (A) One-fourth of its width (B) Half of its width (C) Three-fourth of its width (D) Equal to its width

Description : A foundation is called shallow if its depth, is (A) One-fourth of its width (B) Half of its width (C) Three-fourth of its width (D) Equal to its width

Last Answer : Answer: Option D

Minimum width of landing should be (A) Equal to width of stairs (B) Half the width of stairs (C) Twice the width of stairs (D) One fourth the width of stairs

Description : Minimum width of landing should be (A) Equal to width of stairs (B) Half the width of stairs (C) Twice the width of stairs (D) One fourth the width of stairs

Last Answer : Answer: Option A

Slenderness ratio of the column is the ratio of [ A ] the effective length to width of column [ B ] the effective length to depth of column [ C ] the effective length to least lateral design [ D ] none of the above

Description : Slenderness ratio of the column is the ratio of [ A ] the effective length to width of column [ B ] the effective length to depth of column [ C ] the effective length to least lateral design [ D ] none of the above

Last Answer : [ C ] the effective length to least lateral design

The range within which a load can be applied on a rectangular column, to avoid any tensile stress, is (A) One-half of the base (B) One-fifth of the base (C) One-fourth of the base (D) One-fifth of the base

Description : The range within which a load can be applied on a rectangular column, to avoid any tensile stress,  is  (A) One-half of the base  (B) One-fifth of the base  (C) One-fourth of the base  (D) One-fifth of the base 

Last Answer : (B) One-fifth of the base 

Top bars are extended to the projecting parts of the combined footing of two columns Ldistance apart for a distance of (A) 0.1 L from the outer edge of column (B) 0.1 L from the centre edge of column (C) Half the distance of projection (D) One-fourth the distance of projection

Description : Top bars are extended to the projecting parts of the combined footing of two columns Ldistance apart for a distance of (A) 0.1 L from the outer edge of column (B) 0.1 L from the centre edge of column (C) Half the distance of projection (D) One-fourth the distance of projection

Last Answer : Answer: Option B

The loose pockets in soil mass can be bridged safely by providing a raft foundation provided the soft area is smaller than (A) The column spacing (B) One-third the column spacing (C) Half the column spacing (D) Three-fourth the column spacing

Description : The loose pockets in soil mass can be bridged safely by providing a raft foundation provided the soft area is smaller than (A) The column spacing (B) One-third the column spacing (C) Half the column spacing (D) Three-fourth the column spacing

Last Answer : Answer: Option B

In a short cylindrical external mouthpiece, the vena contracta occurs at a distance __________ the diameter of the orifice from the outlet of orifice. (A) Equal to (B) One-fourth (C) One-third (D) One-half

Description : In a short cylindrical external mouthpiece, the vena contracta occurs at a distance __________ the diameter of the orifice from the outlet of orifice. (A) Equal to (B) One-fourth (C) One-third (D) One-half

Last Answer : Answer: Option B

The discharge through a convergent mouthpiece is __________ the discharge through an internal mouthpiece of the same diameter and head of water. (A) Equal to (B) One-half (C) Three fourth (D) Double

Description : The discharge through a convergent mouthpiece is __________ the discharge through an internal mouthpiece of the same diameter and head of water. (A) Equal to (B) One-half (C) Three fourth (D) Double

Last Answer : Answer: Option D

The ratio of the effective length of a column and minimum radius of gyration of its cross-sectional area, is known (A) Buckling factor (B) Slenderness ratio (C) Crippling factor (D) None of these

Description : The ratio of the effective length of a column and minimum radius of gyration of its cross-sectional area, is known (A) Buckling factor (B) Slenderness ratio (C) Crippling factor (D) None of these

Last Answer : (B) Slenderness ratio

The weaving length of a roadway is the distance (A) Between the channelizing islands (B) Equal to half circumference (C) Equal to total width of adjoining radial roads (D) Equal to diameter of rotary

Description : The weaving length of a roadway is the distance (A) Between the channelizing islands (B) Equal to half circumference (C) Equal to total width of adjoining radial roads (D) Equal to diameter of rotary

Last Answer : Answer: Option A

The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, is (A) One-half of the radius (B) One-third of the radius (C) One-quarter of the radius (D) One-fifth of the radius

Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (C) One-quarter of the radius (D) One-fifth of the radius

Last Answer : (C) One-quarter of the radius

If the effective length of a 32 cm diameter R.C.C. column is 4.40 m, its slenderness ratio, is (A) 40 (B) 45 (C) 50 (D) 55

Description : If the effective length of a 32 cm diameter R.C.C. column is 4.40 m, its slenderness ratio, is (A) 40 (B) 45 (C) 50 (D) 55

Last Answer : Answer: Option D

If is the overall height of a retaining wall retaining a surcharge, the width of the base slab usually provided, is (A) 0.3 H(B) 0.4 H(C) 0.5 H(D) 0.7 H

Description : If is the overall height of a retaining wall retaining a surcharge, the width of the base slab usually provided, is (A) 0.3 H (B) 0.4 H (C) 0.5 H (D) 0.7 H

Last Answer : Answer: Option D

A T-beam behaves as a rectangular beam of a width equal to its flange if its neutral axis (A) Remains within the flange (B) Remains below the slab (C) Coincides the geometrical centre of the beam (D) None of these

Description : A T-beam behaves as a rectangular beam of a width equal to its flange if its neutral axis (A) Remains within the flange (B) Remains below the slab (C) Coincides the geometrical centre of the beam (D) None of these

Last Answer : Answer: Option A

In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Description : In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Last Answer : Answer: Option D

For a ribbed slab (A) Clear spacing between ribs shall not be greater than 4.5 cm (B) Width of the rib shall not be less than 7.5 cm (C) Overall depth of the slab shall not exceed four times the breadth of the rib (D) All the above

Description : For a ribbed slab (A) Clear spacing between ribs shall not be greater than 4.5 cm (B) Width of the rib shall not be less than 7.5 cm (C) Overall depth of the slab shall not exceed four times the breadth of the rib (D) All the above

Last Answer : Answer: Option D

If At is the area of steel cross-section, t is working stress, L is width of road and W is weight of slab per square metre, the spacing of the tie bars for a longitudinal joint, is (A) (100 At × t)/WL (B) 100 At/tWL (C) (100 WAt × t)/tL (D) 100 WL/At t

Description : If At is the area of steel cross-section, t is working stress, L is width of road and W is weight of slab per square metre, the spacing of the tie bars for a longitudinal joint, is (A) (100 At × t)/WL (B) 100 At/tWL (C) (100 WAt × t)/tL (D) 100 WL/At t

Last Answer : Answer: Option D

If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm

Description : If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm

Last Answer : Answer: Option C

The analysis of slab spanning in one direction is done by assuming it to be a beam of (a) 1m length (b) 1m width (c) 1m (d) None of these

Description : The analysis of slab spanning in one direction is done by assuming it to be a beam of (a) 1m length (b) 1m width (c) 1m (d) None of these

Last Answer : (b) 1m width

In a T-beam , the breadth of the rib is equal to the (a) Total thickness of the slab, including cover (b) Width of the portion of the beam in the compression zone (c) Width of the portion of the beam in the compression zone (d) All the above.

Description : In a T-beam , the breadth of the rib is equal to the (a) Total thickness of the slab, including cover (b) Width of the portion of the beam in the compression zone (c) Width of the portion of the beam in the compression zone (d) All the above.

Last Answer : (c) Width of the portion of the beam in the compression zone

Pick up the incorrect statement from the following: (A) The rate of flow of water through a unit cross-sectional area under a unit hydraulic gradient, is called coefficient of permeability (B) The rate of flow of water through a vertical strip of the aquifer of unit width and full depth under a unit hydraulic gradient, is called coefficient of transmissibility (C) The flow of water through aquifers, is governed by the Darcy's law (D) The term 'transmissibility' was introduced by Meinzer

Description : Pick up the incorrect statement from the following: (A) The rate of flow of water through a unit cross-sectional area under a unit hydraulic gradient, is called coefficient of permeability (B) ... aquifers, is governed by the Darcy's law (D) The term 'transmissibility' was introduced by Meinzer

Last Answer : Answer: Option D

The width of road pavements, depends upon (A) Width of traffic lane (B) Number of traffic (C) Width of median strip (D) All the above

Description : The width of road pavements, depends upon (A) Width of traffic lane (B) Number of traffic (C) Width of median strip (D) All the above

Last Answer : Answer: Option D

A piece of timber whose thickness and width are respectively 5 cm and 10 cm is called (A) Slate (B) Plank (C) Board (D) Strip

Description : A piece of timber whose thickness and width are respectively 5 cm and 10 cm is called (A) Slate (B) Plank (C) Board (D) Strip

Last Answer : Answer: Option D

Secondary steel has to be provided across__________ of flanged beams [ A ] Full effective width of flange [ B ] The width of web [ C ] Half of the width of flange [ D ] None of the above.

Description : Secondary steel has to be provided across__________ of flanged beams [ A ] Full effective width of flange [ B ] The width of web [ C ] Half of the width of flange [ D ] None of the above.

Last Answer : [ A ] Full effective width of flange

If D is the degree of the curve of radius R, the exact length of its specified chord, is (A) Radius of the curve × sine of half the degree (B) Diameter of the curve × sine of half the degree (C) Diameter of the curve × cosine of half the degree (D) Diameter of the curve × tangent of half the degree

Description : If D is the degree of the curve of radius R, the exact length of its specified chord, is (A) Radius of the curve sine of half the degree (B) Diameter of the curve sine of half the ... Diameter of the curve cosine of half the degree (D) Diameter of the curve tangent of half the degree

Last Answer : (B) Diameter of the curve × sine of half the degree

A flat slab is supported (A) On beams (B) On columns (C) On beams and columns (D) On columns monolithically built with slab

Description : A flat slab is supported (A) On beams (B) On columns (C) On beams and columns (D) On columns monolithically built with slab

Last Answer : Answer: Option D

The minimum thickness of a flat slab is taken (A) L/32 for end panels without drops (B) L/36 for end panels without drops (C) L/36 for interior panels without drop (D) All the above

Description : The minimum thickness of a flat slab is taken (A) L/32 for end panels without drops (B) L/36 for end panels without drops (C) L/36 for interior panels without drop (D) All the above

Last Answer : Answer: Option D

A reinforcing slab, build monolithically with the supporting columns and is reinforced in two or more directions, without any provision of beams is called a (a) Two way slab (b) Flat slab (c) Continus slab (d) Cireulashion

Description : A reinforcing slab, build monolithically with the supporting columns and is reinforced in two or more directions, without any provision of beams is called a (a) Two way slab (b) Flat slab (c) Continus slab (d) Cireulashion

Last Answer : (b) Flat slab

Reinforced concrete slab supported only on columns is said to be [ A ] Rigid slab [ B ] Flat slab [ C ] Both(a) and (b) [ D ] None of the above.

Description : Reinforced concrete slab supported only on columns is said to be [ A ] Rigid slab [ B ] Flat slab [ C ] Both(a) and (b) [ D ] None of the above.

Last Answer : [ B ] Flat slab

Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of the column (C) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column

Description : Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of ... ) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column

Last Answer : Answer: Option C

Minimum clear cover (in mm) to the main steel bars in slab, beam, column and footing respectively, are (a) 10, 15, 20 and 25 (b) 15, 25, 40 and 75 (c ) 20, 25, 30 and 40 (d) 20, 35, 40 and 75

Description : Minimum clear cover (in mm) to the main steel bars in slab, beam, column and footing respectively, are (a) 10, 15, 20 and 25 (b) 15, 25, 40 and 75 (c ) 20, 25, 30 and 40 (d) 20, 35, 40 and 75

Last Answer : (b) 15, 25, 40 and 75

If W is the load on a circular slab of radius R, the maximum circumferential moment at the centre of the slab, is (A) WR²/16 (B) 2WR²/16 (C) 3WR²/16 (D) Zero

Description : If W is the load on a circular slab of radius R, the maximum circumferential moment at the centre of the slab, is (A) WR²/16 (B) 2WR²/16 (C) 3WR²/16 (D) Zero

Last Answer : Answer: Option C

is the load on a circular slab of radius , the maximum radial moment at the centre of the slab, is (A) WR²/16 (B) 2WR²/16 (C) 3WR²/16 (D) 5WR²/16

Description : is the load on a circular slab of radius , the maximum radial moment at the centre of the slab, is (A) WR²/16 (B) 2WR²/16 (C) 3WR²/16 (D) 5WR²/16

Last Answer : Answer: Option C

If is the uniformly distributed load on a circular slab of radius fixed at its ends, the maximum positive radial moment at its centre, is (A) 3WR²/16 (B) 2WR²/16 (C) WR²/16(D) None of these

Description : If is the uniformly distributed load on a circular slab of radius fixed at its ends, the maximum positive radial moment at its centre, is (A) 3WR²/16 (B) 2WR²/16 (C) WR²/16 (D) None of these

Last Answer : Answer: Option C