The slab is said to be orthotropically reinforced , when the reinforcement is arranged in; [ A ] Single direction [ B ] Two directions at right angles with equal meshes [ C ] Two directions at right angles with unequal meshes [ D ] At the corners only

The slab is said to be orthotropically reinforced , when the reinforcement is arranged in;
[ A ] Single direction
[ B ] Two directions at right angles with equal meshes
[ C ] Two directions at right angles with unequal meshes
[ D ] At the corners only
by

1 Answer

Answer :

[ C ] Two directions at right angles with unequal meshes
by

Related questions

According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is (A) Half of the width of the slab (B) Two-third of the width of the slab (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Description : According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is ... (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Last Answer : Answer: Option C

A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter

Description : A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter

Last Answer : (b) 8 mm diameter

A reinforcing slab, build monolithically with the supporting columns and is reinforced in two or more directions, without any provision of beams is called a (a) Two way slab (b) Flat slab (c) Continus slab (d) Cireulashion

Description : A reinforcing slab, build monolithically with the supporting columns and is reinforced in two or more directions, without any provision of beams is called a (a) Two way slab (b) Flat slab (c) Continus slab (d) Cireulashion

Last Answer : (b) Flat slab

Reinforced concrete slab supported only on columns is said to be [ A ] Rigid slab [ B ] Flat slab [ C ] Both(a) and (b) [ D ] None of the above.

Description : Reinforced concrete slab supported only on columns is said to be [ A ] Rigid slab [ B ] Flat slab [ C ] Both(a) and (b) [ D ] None of the above.

Last Answer : [ B ] Flat slab

The yield line ultimate moment is obtained when the yield line is --------------- to the direction of the reinforcement [ A ] Parallel [ B ] At right angles. [ C ] Passes through [ D ] Crosses at an angle of 45°

Description : The yield line ultimate moment is obtained when the yield line is --------------- to the direction of the reinforcement [ A ] Parallel [ B ] At right angles. [ C ] Passes through [ D ] Crosses at an angle of 45°

Last Answer : [ B ] At right angles.

In T-shaped R C. retaining walls, the main reinforcement in the stem is provided on (A) The front face in one direction (B) The front face in both directions (C) The inner face in one direction (D) The inner face in both directions

Description : In T-shaped R C. retaining walls, the main reinforcement in the stem is provided on (A) The front face in one direction (B) The front face in both directions (C) The inner face in one direction (D) The inner face in both directions

Last Answer : Answer: Option C

While propagating through homogeneous, isotropic media, (A) Directions of both the fields are orthogonal (B) Both the fields are at right angles to the direction of propagation (C) Both (a) and (b) (D) Neither (a) nor (b)

Description : While propagating through homogeneous, isotropic media, (A) Directions of both the fields are orthogonal (B) Both the fields are at right angles to the direction of propagation (C) Both (a) and (b) (D) Neither (a) nor (b)

Last Answer : Answer: Option C

If the ratio of long and short spans of a two way slab with corners held down is r, the actual reduction of B.M. is given by (A) (5/6) (r/1 + r²) M (B) (5/6) (r²/1 + r²) M (C) (5/6) (r²/1 + r3 ) M (D) (5/6) (r²/1 + r4 ) M

Description : If the ratio of long and short spans of a two way slab with corners held down is r, the actual reduction of B.M. is given by (A) (5/6) (r/1 + r²) M (B) (5/6) (r²/1 + r²) M (C) (5/6) (r²/1 + r3 ) M (D) (5/6) (r²/1 + r4 ) M

Last Answer : Answer: Option D

Design of a two way slab simply supported on edges and having no provision to prevent the corners from lifting, is made by (A) Rankine formula (B) Marcus formula (C) Rankine Grashoff formula (D) Grashoff formula

Description : Design of a two way slab simply supported on edges and having no provision to prevent the corners from lifting, is made by (A) Rankine formula (B) Marcus formula (C) Rankine Grashoff formula (D) Grashoff formula

Last Answer : Answer: Option C

A two way slab (a) May be simply supported on the four edges, with comers not held down and carrying uniformly distributed load. (b) May be simply supported on the four edge , with corners held down and carrying uniformly distributed load. (c) May have edges fixed or continuous and carrying uniformly distributed load. (d) All the above.

Description : A two way slab (a) May be simply supported on the four edges, with comers not held down and carrying uniformly distributed load. (b) May be simply supported on the four edge , with corners held ... . (c) May have edges fixed or continuous and carrying uniformly distributed load. (d) All the above.

Last Answer : (d) All the above.

For a slab supported on its four edges with corners held down and loaded uniformly, the Marcus correction factor to the moments obtained by Grashoff Rankine's theory (A) Is always less than 1 (B) Is always greater than 1 (C) Can be more than 1 (D) Can be less than 1

Description : For a slab supported on its four edges with corners held down and loaded uniformly, the Marcus correction factor to the moments obtained by Grashoff Rankine's theory (A) Is always less than 1 (B) Is always greater than 1 (C) Can be more than 1 (D) Can be less than 1

Last Answer : Answer: Option A

A slab simply supported on the four edges, with corners not held down and carrying uniformly distributed load, is used in (a) Singly storeyed buildings. (b) Double storeyed buildings. (c) Multi storeyed buildings (d) All the above

Description : A slab simply supported on the four edges, with corners not held down and carrying uniformly distributed load, is used in (a) Singly storeyed buildings. (b) Double storeyed buildings. (c) Multi storeyed buildings (d) All the above

Last Answer : (a) Singly storeyed buildings.

A number of forces acting at a point will be in equilibrium if (A) Their total sum is zero (B) Two resolved parts in two directions at right angles are equal (C) Sum of resolved parts in any two perpendicular directions are both zero (D) All of them are inclined equally

Description : A number of forces acting at a point will be in equilibrium if (A) Their total sum is zero (B) Two resolved parts in two directions at right angles are equal (C) Sum of resolved parts in any two perpendicular directions are both zero (D) All of them are inclined equally

Last Answer : (C) Sum of resolved parts in any two perpendicular directions are both zero

If the sides of a slab simply supported on edges and spanning in two directions are equal, the maximum bending moment is multiplied by (A) 0.2 (B) 0.3 (C) 0.4 (D) 0.5

Description : If the sides of a slab simply supported on edges and spanning in two directions are equal, the maximum bending moment is multiplied by (A) 0.2 (B) 0.3 (C) 0.4 (D) 0.5

Last Answer : Answer: Option D

Two vectors are said to be equal if – (1) only their magnitudes are same (2) only their directions are same (3) both magnitude and direction are same (4) magnitudes are same but directions are opposite

Description : Two vectors are said to be equal if – (1) only their magnitudes are same (2) only their directions are same (3) both magnitude and direction are same (4) magnitudes are same but directions are opposite

Last Answer : (3) both magnitude and direction are same Explanation: If the magnitude as well as direction of two vectors are equal, then they are known as equal vectors. In other words, two vectors are ... headed towards the same direction. For two equal vectors, their directed line segments must be parallel.

Two vectors are said to be equal if (1) only their magnitudes are same (2) only their directions are same (3) both magnitude and direction are same (4) magnitudes are same but directions are opposite

Description : Two vectors are said to be equal if (1) only their magnitudes are same (2) only their directions are same (3) both magnitude and direction are same (4) magnitudes are same but directions are opposite 

Last Answer : both magnitude and direction are same

In a singly reinforced beam, the effective depth is measured from its compression edge to (A) Tensile edge (B) Tensile reinforcement (C) Neutral axis of the beam (D) Longitudinal central axis

Description : In a singly reinforced beam, the effective depth is measured from its compression edge to (A) Tensile edge (B) Tensile reinforcement (C) Neutral axis of the beam (D) Longitudinal central axis

Last Answer : Answer: Option B

Shear resistance of concrete in a reinforced concrete beam is dependent on (a) Tension reinforcement in the beam (b) Compression reinforcement in the beam (c ) Shear reinforcement in the beam (d) None of the reinforcements in the beam

Description : Shear resistance of concrete in a reinforced concrete beam is dependent on (a) Tension reinforcement in the beam (b) Compression reinforcement in the beam (c ) Shear reinforcement in the beam (d) None of the reinforcements in the beam

Last Answer : (a) Tension reinforcement in the beam

In a doubly reinforced beam , steel reinforcement is provided in a (a) Tensile zone (b) Compression zone (c) Either (a) & (b) (d) Both (a) & (b)

Description : In a doubly reinforced beam , steel reinforcement is provided in a (a) Tensile zone (b) Compression zone (c) Either (a) & (b) (d) Both (a) & (b)

Last Answer : (d) Both (a) & (b)

In an over-reinforced section (a) Steel reinforcement is not fully stressed to its permissible value (b) Concrete is not fully stressed to its permissible value (c) Either (a) and (b) (d) Both (a) and (b)

Description : In an over-reinforced section (a) Steel reinforcement is not fully stressed to its permissible value (b) Concrete is not fully stressed to its permissible value (c) Either (a) and (b) (d) Both (a) and (b)

Last Answer : (a) Steel reinforcement is not fully stressed to its permissible value

In a singly reinforced beam, the effective depth is measured form the compression edge to the (a) Tensile edge (b) Centre of tensile reinforcement (c) Neutral axis of the beam (d) All of the above

Description : In a singly reinforced beam, the effective depth is measured form the compression edge to the (a) Tensile edge (b) Centre of tensile reinforcement (c) Neutral axis of the beam (d) All of the above

Last Answer : (b) Centre of tensile reinforcement

In a simply supported reinforced concrete beam, the reinforcement is placed. (a) Above the neutral axis (b) Below the neutral axis (c) At the neutral axis (d) None of these

Description : In a simply supported reinforced concrete beam, the reinforcement is placed. (a) Above the neutral axis (b) Below the neutral axis (c) At the neutral axis (d) None of these

Last Answer : (b) Below the neutral axis

In singly reinforced beams, steel reinforcement is provided in (a) Compressive zone (b) Tensile zone (c) Neutral zone (d) All the above

Description : In singly reinforced beams, steel reinforcement is provided in (a) Compressive zone (b) Tensile zone (c) Neutral zone (d) All the above

Last Answer : (b) Tensile zone

In the reinforced cement concrete structure, the steel reinforcement consists of . (a) Deformed bars (b) Cold twisted bars (c) Mildsteel and medium tensile steel bars (d) All of these

Description : In the reinforced cement concrete structure, the steel reinforcement consists of . (a) Deformed bars (b) Cold twisted bars (c) Mildsteel and medium tensile steel bars (d) All of these

Last Answer : (d) All of these

The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

The transverse reinforcements provided at right angles to the main reinforcement (A) Distribute the load (B) Resist the temperature stresses (C) Resist the shrinkage stress (D) All the above

Description : The transverse reinforcements provided at right angles to the main reinforcement (A) Distribute the load (B) Resist the temperature stresses (C) Resist the shrinkage stress (D) All the above

Last Answer : Answer: Option D

The transverse reinforcements provided at right angles to the main reinforcement. (a) To distribute the load. (b) To resist the temp stresses (c) To resist the shrinkage stresses (d) All the above

Description : The transverse reinforcements provided at right angles to the main reinforcement. (a) To distribute the load. (b) To resist the temp stresses (c) To resist the shrinkage stresses (d) All the above

Last Answer : (d) All the above

The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6

Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6

Last Answer : Answer: Option C

The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6

Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6

Last Answer : (c) 0.9

It is preferable, that the design of slab should result in [ A ] A balanced section [ B ] An under reinforced section [ C ] Over reinforced section [ D ] None of the above.

Description : It is preferable, that the design of slab should result in [ A ] A balanced section [ B ] An under reinforced section [ C ] Over reinforced section [ D ] None of the above.

Last Answer : [ B ] An under reinforced section

To develop complete yield line pattern the slab must be [ A ] Under reinforced [ B ] Over reinforced [ C ] Both (a) and (b) [ D ] None of the above.

Description : To develop complete yield line pattern the slab must be [ A ] Under reinforced [ B ] Over reinforced [ C ] Both (a) and (b) [ D ] None of the above.

Last Answer : [ A ] Under reinforced

In a slab, the pitch of the main reinforcement should not exceed its effective depth (A) Three times (B) Four times (C) Five times (D) Two times

Description : In a slab, the pitch of the main reinforcement should not exceed its effective depth (A) Three times (B) Four times (C) Five times (D) Two times

Last Answer : Answer: Option A

The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force

Description : The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force

Last Answer : Answer: Option B

Distribution reinforcement in a simply supported slab, is provided to distribute (A) Load (B) Temperature stress (C) Shrinkage stress (D) All the above

Description : Distribution reinforcement in a simply supported slab, is provided to distribute (A) Load (B) Temperature stress (C) Shrinkage stress (D) All the above

Last Answer : Answer: Option D

If the diameter of the main reinforcement in a slab is 16 mm, the concrete cover to main bars is (A) 10 mm (B) 12 mm (C) 14 mm (D) 16 mm

Description : If the diameter of the main reinforcement in a slab is 16 mm, the concrete cover to main bars is (A) 10 mm (B) 12 mm (C) 14 mm (D) 16 mm

Last Answer : Answer: Option D

A part of the slab may be considered as the flange of the T-beam if (A) Flange has adequate reinforcement transverse to beam (B) It is built integrally with the beam (C) It is effectively bonded together with the beam (D) All the above

Description : A part of the slab may be considered as the flange of the T-beam if (A) Flange has adequate reinforcement transverse to beam (B) It is built integrally with the beam (C) It is effectively bonded together with the beam (D) All the above

Last Answer : Answer: Option D

Pick up the incorrect statement from the following: (A) In the stem of a retaining wall, reinforcement is provided near the earth side (B) In the toe slab of a retaining wall, reinforcement is provided at the bottom of the slab (C) In the heel slab of a retaining wall, reinforcement is provided at the top of the slab (D) None of these

Description : Pick up the incorrect statement from the following: (A) In the stem of a retaining wall, reinforcement is provided near the earth side (B) In the toe slab of a retaining wall, reinforcement is ... slab of a retaining wall, reinforcement is provided at the top of the slab (D) None of these

Last Answer : Answer: Option D

Reinforcement in cement concrete slab of road pavements, is placed (A) Longitudinally (B) Transversely (C) Longitudinally and transversely (D) In the form of welded wire mesh

Description : Reinforcement in cement concrete slab of road pavements, is placed (A) Longitudinally (B) Transversely (C) Longitudinally and transversely (D) In the form of welded wire mesh

Last Answer : Answer: Option D

When shear stress exceeds the permissible limit in a slab, then it is reduced by (A) Increasing the depth (B) Providing shear reinforcement (C) Using high strength steel (D) Using thinner bars but more in number

Description : When shear stress exceeds the permissible limit in a slab, then it is reduced by (A) Increasing the depth (B) Providing shear reinforcement (C) Using high strength steel (D) Using thinner bars but more in number

Last Answer : Answer: Option A

The temperature reinforcement in the vertical slab of a T-shaped R.C. retaining wall is (A) Not needed (B) Provided equally on inner and front faces (C) Provided more on inner face than on front face (D) Provided more on front face than on inner face

Description : The temperature reinforcement in the vertical slab of a T-shaped R.C. retaining wall is (A) Not needed (B) Provided equally on inner and front faces (C) Provided more on inner face than on front face (D) Provided more on front face than on inner face

Last Answer : Answer: Option D

The main reinforcement of a R.C. slab consists of 10 mm bars at 100 mm spacing; if it is desired to replace the 10 mm bars by 12 mm bars, then the spacing of 12mm bars should be (a) 120 mm (b) 140 mm (c ) 144 mm (d) 160mm

Description : The main reinforcement of a R.C. slab consists of 10 mm bars at 100 mm spacing; if it is desired to replace the 10 mm bars by 12 mm bars, then the spacing of 12mm bars should be (a) 120 mm (b) 140 mm (c ) 144 mm (d) 160mm

Last Answer : (c ) 144 mm

The amount of reinforcement for main bars in a slab, is based upon (a) Maximum bending moment (b) Minimum bending moment (c) Maximum shear force (d) Minimum shear force

Description : The amount of reinforcement for main bars in a slab, is based upon (a) Maximum bending moment (b) Minimum bending moment (c) Maximum shear force (d) Minimum shear force

Last Answer : (a) Maximum bending moment

The reinforcement in a continuous slab is provided (a) At the top of the slab portion over the intermediate supports. (b) At the bottom of the slab portion over the intermediate supports. (c) All the middle of the slab portion over the intermediate supports (d) All the above

Description : The reinforcement in a continuous slab is provided (a) At the top of the slab portion over the intermediate supports. (b) At the bottom of the slab portion over the intermediate supports. (c) All the middle of the slab portion over the intermediate supports (d) All the above

Last Answer : (a) At the top of the slab portion over the intermediate supports.

in a simply supported slab, the pitch of distribution reinforcement should not be more than_____________the effective depth of slab or 60cm which ever is smaller. (a) Double (b) Three times (c) Five times (d) Six times

Description : in a simply supported slab, the pitch of distribution reinforcement should not be more than_____________the effective depth of slab or 60cm which ever is smaller. (a) Double (b) Three times (c) Five times (d) Six times

Last Answer : (c) Five times

The pitch of bars of main reinforcement in slab should not exceed ________the effective depth of slab. (a) Double (b) Three times (c) Five times (d) Six times

Description : The pitch of bars of main reinforcement in slab should not exceed ________the effective depth of slab. (a) Double (b) Three times (c) Five times (d) Six times

Last Answer : (b) Three times

The purpose of transverse reinforcement, in a slab is to (a) Distribute the effect to f point load on the slab more evenly and uniformly (b) Distribute the shrinkage and temp cracks more ever (c) Keep the main reinforcement in position (d) All of the above.

Description : The purpose of transverse reinforcement, in a slab is to (a) Distribute the effect to f point load on the slab more evenly and uniformly (b) Distribute the shrinkage and temp cracks more ever (c) Keep the main reinforcement in position (d) All of the above.

Last Answer : (d) All of the above.

In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Description : In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Last Answer : (d) Depth of rib

In a limit state method of design, when shear reinforcement is not provided, the calculated shear stress at the critical section of a slab shall not exceed; [ A ] Ks 0.25 v fck [ B ] ks 0.20 v fck [ C ] ks 0.16 v fck [ D ] ks 0.10 v fck

Description : In a limit state method of design, when shear reinforcement is not provided, the calculated shear stress at the critical section of a slab shall not exceed; [ A ] Ks 0.25 v fck [ B ] ks 0.20 v fck [ C ] ks 0.16 v fck [ D ] ks 0.10 v fck

Last Answer : [ A ] Ks 0.25 v fck

The size of the mesh at each corner meant for torsion reinforcement in a rectangular slab of size (Lx ´ Ly) is Lx = shorter span Lx = Longer span [ A ] 0.1 Ly x 1 Ly [ B ] 0.2 Ly x 0.2 Ly [ C ] 0.1 Lx x 0.1 Lx [ D ] 0.2 Lx x 0.2 Lx

Description : The size of the mesh at each corner meant for torsion reinforcement in a rectangular slab of size (Lx ´ Ly) is Lx = shorter span Lx = Longer span [ A ] 0.1 Ly x 1 Ly [ B ] 0.2 Ly x 0.2 Ly [ C ] 0.1 Lx x 0.1 Lx [ D ] 0.2 Lx x 0.2 Lx

Last Answer : [ D ] 0.2 Lx x 0.2 Lx