Description : A reinforcing slab, build monolithically with the supporting columns and is reinforced in two or more directions, without any provision of beams is called a (a) Two way slab (b) Flat slab (c) Continus slab (d) Cireulashion
Last Answer : (b) Flat slab
Description : Pick up the correct statement from the following: (A) The roof slabs of multi-storeyed buildings are constructed monolithically to carry the various floor loads (B) The beams of multi-storeyed ... slab is spanned across the secondary beams provided between the main beams (D) All of these
Last Answer : Answer: Option D
Description : Reinforced concrete slab supported only on columns is said to be [ A ] Rigid slab [ B ] Flat slab [ C ] Both(a) and (b) [ D ] None of the above.
Last Answer : [ B ] Flat slab
Description : For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9
Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6
Last Answer : Answer: Option C
Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6
Last Answer : (c) 0.9
Description : The portion of the slab which acts monolithically with the beam and which resists the compressive stresses, is called _________of flange of the T-beam (a) Length (b) Breadth (c) Thickness (d) Depth
Last Answer : (b) Breadth
Description : If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm
Description : Flanged beams are preferred when the concrete in the slab is on the [ A ] compression side of the beam [ B ] tension side of the beam [ C ] may be compression side or tension side of the beam [ D ] none of the above
Last Answer : [ A ] compression side of the beam
Description : A grillage foundation (A) Is provided for heavily loaded isolated columns (B) Is treated as spread foundation (C) Consists of two sets of perpendicularly placed steel beams (D) All the above
Description : For the construction of R.C.C. slabs, columns, beams, walls, etc. the grade of concrete mix used, is (A) 1 : 3 : 6 (B) 1 : 1½ : 3 (C) 1 : 2 : 4 (D) 1 : 1 : 2
Last Answer : (C) 1 : 2 : 4
Description : Pick up the correct statement from the following: (A) Construction joints in columns are provided a few cm below the junction of beam (B) Construction joints in columns are provided at the bottom ... (C) Construction joints in beams and slabs are provided within middle third (D) All the above
Description : Mild steel is used for (A) Structural works in beams, joints and girders (B) Small sized water pipes (C) Columns and struts (D) None of these
Last Answer : Answer: Option A
Description : Cast iron is used for (A) Structural works in beams (B) Small sized water pipes (C) Columns and struts (D) None to these
Description : Wrought iron is used for (A) Structural works in beams (B) Small sized water pipes (C) Columns and struts (D) None to these
Last Answer : Answer: Option B
Description : In a group housing project, it is proposed to use pre-fabricated RCC beams and columns. The most useful construction equipment is (a) Derrick Crane (b) Chute (c) Weigh Batcher (d) Transit Mixer
Last Answer : (a) Derrick Crane
Description : A simply supported beam A carries a point load at its mid span. Another identical beam B carries the same load but uniformly distributed over the entire span. The ratio of the maximum deflections of the beams A and B, will be (A) 2/3 (B) 3/2 (C) 5/8 (D) 8/5
Last Answer : (D) 8/5
Description : Design of R.C.C. simply supported beams carrying U.D.L. is based on the resultant B.M. at (A) Supports (B) Mid span (C) Every section (D) Quarter span
Description : Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of ... ) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column
Description : In sliding contact bearings, a positive pressure can be built up and a load supported by a fluid only by the use of a: [IES-2005] (a) Diverging film (b) Converging-diverging film (c) Converging film (d) Flat film
Last Answer : (c) Converging film
Description : Distribution reinforcement in a simply supported slab, is provided to distribute (A) Load (B) Temperature stress (C) Shrinkage stress (D) All the above
Description : If K is a constant depending upon the ratio of the width of the slab to its effective span l, x is the distance of the concentrated load from the nearer support, bw is the width of the area of contact of the concentrated load measured ... ) Kx (1 - x/l) + bw (C) Kx (1 + x/l) + bw (D) All the above
Description : If the sides of a slab simply supported on edges and spanning in two directions are equal, the maximum bending moment is multiplied by (A) 0.2 (B) 0.3 (C) 0.4 (D) 0.5
Description : The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these
Description : If l1 and l2 are the lengths of long and short spans of a two way slab simply supported on four edges and carrying a load w per unit area, the ratio of the loads split into w1 and w2acting on strips parallel to l2 and l1 is (A) ... l1 (B) w1/w2 = (l2/l1)² (C) w1/w2 = (l2/l1)3 (D) w1/w2 = (l2/l1)
Description : The maximum ratio of span to depth of a slab simply supported and spanning in two directions, is (A) 25 (B) 30 (C) 35 (D) 40
Description : Design of a two way slab simply supported on edges and having no provision to prevent the corners from lifting, is made by (A) Rankine formula (B) Marcus formula (C) Rankine Grashoff formula (D) Grashoff formula
Description : The pitch of the main bars in a simply supported slab, should not exceed its effective depth by (A) Three times (B) Four times (C) Five times (D) Six times
Description : In a simply supported slab, alternate bars are curtailed at (A) 1/4th of the span (B) 1/5th of the span (C) 1/6th of the span (D) 1/7th of the span
Description : The maximum ratio of span to depth of a slab simply supported and spanning in one direction, is (A) 35 (B) 25 (C) 30 (D) 20
Description : For a slab supported on its four edges with corners held down and loaded uniformly, the Marcus correction factor to the moments obtained by Grashoff Rankine's theory (A) Is always less than 1 (B) Is always greater than 1 (C) Can be more than 1 (D) Can be less than 1
Description : The maximum ratio of span to depth of a slab simple supported and spanning in two directions, is (a) 25 (b) 30 (c) 35 (d) 40
Last Answer : (c) 35
Description : The maximum ratio of span to depth of a slab simply supported and spanning in one direction is (a) 35 (b) 25 (c) 30 (d) 20
Last Answer : (c) 30
Description : The effective span of a simply supported slab is (a) Distance between the centers of the bearings (b) Clear distance between the inner faces of the walls plus twice he thickness of the slab. (c) Cleat spa plus effective depth of the slab. (d) All the above
Last Answer : (c) Cleat spa plus effective depth of the slab.
Description : In a simply supported slab, alternate bars are curtailed at (a) 1/4th of the span (b) 1/5th of the span (c) 1/6th of the span (d) 1/7th of the span
Last Answer : (d) 1/7th of the span
Description : If the sides o a slab simply supported on its edges and spanning in two way are equal, then the maximum bending moment is multiplied by. (a) 0.25 (b) 0.50 (c) 0.75 (d) 0.85
Last Answer : (b) 0.50
Description : A slab simply supported on the four edges, with corners not held down and carrying uniformly distributed load, is used in (a) Singly storeyed buildings. (b) Double storeyed buildings. (c) Multi storeyed buildings (d) All the above
Last Answer : (a) Singly storeyed buildings.
Description : A two way slab (a) May be simply supported on the four edges, with comers not held down and carrying uniformly distributed load. (b) May be simply supported on the four edge , with corners held ... . (c) May have edges fixed or continuous and carrying uniformly distributed load. (d) All the above.
Last Answer : (d) All the above.
Description : When the slab is supported on all the four edges and the ratio of long span to short span is small, bending takes place along both the spans, such a slab is known as (a) Slab spanning in one direction (b) One way slab. (c) Slab spanning in two direction. (d) Two-way slab.
Last Answer : (d) Two-way slab.
Description : The clear cover in a simply supported slab should not be less than the diameter of the reinforcing bar (a) Correct (b) Incorrect’ (c) Not known (d) None of these
Last Answer : (a) Correct
Description : in a simply supported slab, the pitch of distribution reinforcement should not be more than_____________the effective depth of slab or 60cm which ever is smaller. (a) Double (b) Three times (c) Five times (d) Six times
Last Answer : (c) Five times
Description : The span/over all depth ratio for a simply supported two-way slab according to IS : 456- 2000 is given by [ A ] 20 [ B ] 28 [ C ] 32 [ D ] 40
Last Answer : [ B ] 28
Description : Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii
Last Answer : [ A ] i
Description : What are the beams and columns of a wall called ?
Last Answer : The beams of the walls are horizontal and the columns are vertical.
Description : If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span ... (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²
Description : The effective width of a column strip of a flat slab, is (A) One-fourth the width of the panel (B) Half the width of the panel (C) Radius of the column (D) Diameter of the column
Description : Thickened part of a flat slab over its supporting column, is technically known as (A) Drop panel (B) Capital (C) Column head (D) None of these
Description : Enlarged head of a supporting column of a flat slab is technically known as (A) Supporting end of the column (B) Top of the column (C) Capital (D) Drop panel
Description : The minimum thickness of a flat slab is taken (A) L/32 for end panels without drops (B) L/36 for end panels without drops (C) L/36 for interior panels without drop (D) All the above