When a slab is continuous over several spans, negative (i.e. hogging ) bending moment is induced over the (a) End supports (b) Intermediate supports (c) Both (a) & (b) (d) Non of the

When a slab is continuous over several spans, negative (i.e. hogging ) bending moment is induced over the
(a) End supports
(b) Intermediate supports
(c) Both (a) & (b)
(d) Non of the
by

1 Answer

Answer :

(b) Intermediate supports
by

Related questions

An R.C.C. roof slab is designed as a two way slab if (A) It supports live loads in both directions (B) The ratio of spans in two directions is less than 2 (C) The slab is continuous over two supports (D) The slab is discontinuous at edges

Description : An R.C.C. roof slab is designed as a two way slab if (A) It supports live loads in both directions (B) The ratio of spans in two directions is less than 2 (C) The slab is continuous over two supports (D) The slab is discontinuous at edges

Last Answer : Answer: Option B

Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to resist a sagging bending moment near mid-span. (c) When the slab is built into a brick or masonry wall the slab should be designed to resist a hogging moment at the face of the support. (d) All of the above.

Description : Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to ... be designed to resist a hogging moment at the face of the support. (d) All of the above.

Last Answer : (d) All of the above.

The reinforcement in a continuous slab is provided (a) At the top of the slab portion over the intermediate supports. (b) At the bottom of the slab portion over the intermediate supports. (c) All the middle of the slab portion over the intermediate supports (d) All the above

Description : The reinforcement in a continuous slab is provided (a) At the top of the slab portion over the intermediate supports. (b) At the bottom of the slab portion over the intermediate supports. (c) All the middle of the slab portion over the intermediate supports (d) All the above

Last Answer : (a) At the top of the slab portion over the intermediate supports.

The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6

Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6

Last Answer : Answer: Option C

To ensure that the hogging bending moment at two points of suspension of a pile of length L equals the sagging moment at its centre, the distances of the points of suspension from either end, is (A) 0.107 L (B) 0.207 L (C) 0.307 L (D) 0.407 L

Description : To ensure that the hogging bending moment at two points of suspension of a pile of length L equals the sagging moment at its centre, the distances of the points of suspension from either end, is (A) 0.107 L (B) 0.207 L (C) 0.307 L (D) 0.407 L

Last Answer : Answer: Option B

The concavity produced on the beam section about the centre line when downward force acts on it is called as (a) Hogging or positive bending moment (b) Hogging or negative bending moment (c) Sagging or positive bending moment (d) Sagging or negative bending moment

Description : The concavity produced on the beam section about the centre line when downward force acts on it is called as (a) Hogging or positive bending moment (b) Hogging or negative bending moment (c) Sagging or positive bending moment (d) Sagging or negative bending moment

Last Answer : (b) Hogging or negative bending moment

Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ A ] i

When the slab is supported on all the four edges and the ratio of long span to short span is small, bending takes place along both the spans, such a slab is known as (a) Slab spanning in one direction (b) One way slab. (c) Slab spanning in two direction. (d) Two-way slab.

Description : When the slab is supported on all the four edges and the ratio of long span to short span is small, bending takes place along both the spans, such a slab is known as (a) Slab spanning in one direction (b) One way slab. (c) Slab spanning in two direction. (d) Two-way slab.

Last Answer : (d) Two-way slab.

In a combined footing for two columns carrying unequal loads, the maximum hogging bending moment occurs at (A) Less loaded column (B) More loaded column (C) A point of the maximum shear force (D) A point of zero shear force

Description : In a combined footing for two columns carrying unequal loads, the maximum hogging bending moment occurs at (A) Less loaded column (B) More loaded column (C) A point of the maximum shear force (D) A point of zero shear force

Last Answer : Answer: Option D

For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9

Description : For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9

Last Answer : Answer: Option D

If the length of an intermediate span of a continuous slab is 5m, the length of the end span is kept (A) 4.5 m (B) 4.0 m (C) 3.5 m (D) 3.0 m

Description : If the length of an intermediate span of a continuous slab is 5m, the length of the end span is kept (A) 4.5 m (B) 4.0 m (C) 3.5 m (D) 3.0 m

Last Answer : Answer: Option A

Pick up the correct statement from the following: (A) The bent up bars at a support resist the negative bending moment (B) The bent up bars at a support resist the sharing force (C) The bending of bars near supports is generally at 45° (D) All the above

Description : Pick up the correct statement from the following: (A) The bent up bars at a support resist the negative bending moment (B) The bent up bars at a support resist the sharing force (C) The bending of bars near supports is generally at 45° (D) All the above

Last Answer : (D) All the above

If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than (A) WL/12 (L - 2D/3)² (B) WL/10 (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Description : If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span ... (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Last Answer : Answer: Option C

When load is applied on concrete pavement (A) Away from edges, the maximum bending moment is negative (B) Away from edges, the maximum bending moment cause compression (C) On the edges, the maximum stress is parallel to the edge of the slab (D) None of these

Description : When load is applied on concrete pavement (A) Away from edges, the maximum bending moment is negative (B) Away from edges, the maximum bending moment cause compression (C) On the edges, the maximum stress is parallel to the edge of the slab (D) None of these

Last Answer : Answer: Option C

Consider the following statements: Sinking of an intermediate support of a continuous beam 1. Reduces the negative moment at support. 2. Increases the negative moment at support. 3. Reduces the positive moment at support. 4. Increases the positive moment at the centre of span. Of these statements (A) 1 and 4 are correct (B) 1 and 3 are correct (C) 2 and 3 are correct (D) 2 and 4 are correct

Description : Consider the following statements: Sinking of an intermediate support of a continuous beam 1. Reduces the negative moment at support. 2. Increases the negative moment at support. 3. Reduces the positive moment at ... 1 and 3 are correct (C) 2 and 3 are correct (D) 2 and 4 are correct

Last Answer : (A) 1 and 4 are correct

Sinking of an intermediate support of a continuous beam (i) Reduces the negative moment at support (ii) Increases the negative moment at support (iii) Reduces the positive moment at center of span (iv) Increases the positive moment at center of span The correct answer is (A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Description : Sinking of an intermediate support of a continuous beam (i) Reduces the negative moment at support (ii) Increases the negative moment at support (iii) Reduces the positive moment at center of span (iv) Increases the positive moment ... (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Last Answer : Answer: Option B

In continuous beam, the intermediate beams are subjected to a. some bending moment b. no bending moment c. no slope d.no deflection

Description : In continuous beam, the intermediate beams are subjected to a. some bending moment b. no bending moment c. no slope d.no deflection

Last Answer : a. some bending moment

A continuous beam is simply supported on its one or both the end supports the fixing moment on simply supported beam end is a. zero b. infinite c. neglected in calculation d. multiplied by a cross over factor in calculation

Description : A continuous beam is simply supported on its one or both the end supports the fixing moment on simply supported beam end is a. zero b. infinite c. neglected in calculation d. multiplied by a cross over factor in calculation

Last Answer : a. zero

A pile of length carrying a uniformly distributed load per metre length is suspended at the centre and from other two points 0.15 L from either end ; the maximum hogging moment will be (A) WL²/15 (B) WL²/30 (C) WL²/60 (D) WL²/90

Description : A pile of length carrying a uniformly distributed load per metre length is suspended at the centre and from other two points 0.15 L from either end ; the maximum hogging moment will be (A) WL²/15 (B) WL²/30 (C) WL²/60 (D) WL²/90

Last Answer : Answer: Option D

A beam of length L supported on two intermediate rollers carries a uniformly distributed load on its entire length. If sagging B.M. and hogging B.M. of the beam are equal, the length of each overhang, is (A) 0.107 L (B) 0.207 L (C) 0.307 L(D) 0.407 L

Description : A beam of length L supported on two intermediate rollers carries a uniformly distributed load on its entire length. If sagging B.M. and hogging B.M. of the beam are equal, the length of each overhang, is (A) 0.107 L (B) 0.207 L (C) 0.307 L(D) 0.407 L

Last Answer : (B) 0.207 L

Bending moment at supports in case of simply supported beam is always (a) Zero (b) Positive (c) Negative (d) Depends upon loading

Description : Bending moment at supports in case of simply supported beam is always (a) Zero (b) Positive (c) Negative (d) Depends upon loading

Last Answer : (a) Zero

For a simply supported beam with a central load, the bending moment is (A) Least at the centre (B) Least at the supports (C) Maximum at the supports (D) Maximum at the centre

Description : For a simply supported beam with a central load, the bending moment is  (A) Least at the centre  (B) Least at the supports  (C) Maximum at the supports  (D) Maximum at the centre

Last Answer : (D) Maximum at the centre

The maximum bending moment due to a moving load on a simply supported beam, occurs (A) At the mid span (B) At the supports (C) Under the load (D) Anywhere on the beam

Description : The maximum bending moment due to a moving load on a simply supported beam, occurs (A) At the mid span (B) At the supports (C) Under the load (D) Anywhere on the beam

Last Answer : (C) Under the load

For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Description : For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Last Answer : Answer: Option D

In continuous beam between intermediate supports the deflection is a. convex down b. convex up c. concave up d. concave down

Description : In continuous beam between intermediate supports the deflection is a. convex down b. convex up c. concave up d. concave down

Last Answer : b. convex up

The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force

Description : The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force

Last Answer : Answer: Option B

If the sides of a slab simply supported on edges and spanning in two directions are equal, the maximum bending moment is multiplied by (A) 0.2 (B) 0.3 (C) 0.4 (D) 0.5

Description : If the sides of a slab simply supported on edges and spanning in two directions are equal, the maximum bending moment is multiplied by (A) 0.2 (B) 0.3 (C) 0.4 (D) 0.5

Last Answer : Answer: Option D

The design of heel slab of a retaining wall is based on the maximum bending moment due to: (A) Its own weight (B) Weight of the soil above it (C) Load of the surcharge, if any (D) All the above

Description : The design of heel slab of a retaining wall is based on the maximum bending moment due to: (A) Its own weight (B) Weight of the soil above it (C) Load of the surcharge, if any (D) All the above

Last Answer : Answer: Option D

The amount of reinforcement for main bars in a slab, is based upon (a) Maximum bending moment (b) Minimum bending moment (c) Maximum shear force (d) Minimum shear force

Description : The amount of reinforcement for main bars in a slab, is based upon (a) Maximum bending moment (b) Minimum bending moment (c) Maximum shear force (d) Minimum shear force

Last Answer : (a) Maximum bending moment

If the sides o a slab simply supported on its edges and spanning in two way are equal, then the maximum bending moment is multiplied by. (a) 0.25 (b) 0.50 (c) 0.75 (d) 0.85

Description : If the sides o a slab simply supported on its edges and spanning in two way are equal, then the maximum bending moment is multiplied by. (a) 0.25 (b) 0.50 (c) 0.75 (d) 0.85

Last Answer : (b) 0.50

The maximum bending moment and deflection for two way slab is much _____- ____than that of a one wayslad. (a) Greater (b) Smaller (c) Equal (d) All of these

Description : The maximum bending moment and deflection for two way slab is much _________than that of a one wayslad. (a) Greater (b) Smaller (c) Equal (d) All of these

Last Answer : (b) Smaller

The three moments equation is applicable only when (A) The beam is prismatic (B) There is no settlement of supports (C) There is no discontinuity such as hinges within the span (D) The spans are equal

Description : The three moments equation is applicable only when (A) The beam is prismatic (B) There is no settlement of supports (C) There is no discontinuity such as hinges within the span (D) The spans are equal

Last Answer : (C) There is no discontinuity such as hinges within the span

If l1 and l2 are the lengths of long and short spans of a two way slab simply supported on four edges and carrying a load w per unit area, the ratio of the loads split into w1 and w2acting on strips parallel to l2 and l1 is (A) w1/w2 = l2/l1 (B) w1/w2 = (l2/l1)² (C) w1/w2 = (l2/l1)3 (D) w1/w2 = (l2/l1)

Description : If l1 and l2 are the lengths of long and short spans of a two way slab simply supported on four edges and carrying a load w per unit area, the ratio of the loads split into w1 and w2acting on strips parallel to l2 and l1 is (A) ... l1 (B) w1/w2 = (l2/l1)² (C) w1/w2 = (l2/l1)3 (D) w1/w2 = (l2/l1)

Last Answer : Answer: Option D

If the ratio of long and short spans of a two way slab with corners held down is r, the actual reduction of B.M. is given by (A) (5/6) (r/1 + r²) M (B) (5/6) (r²/1 + r²) M (C) (5/6) (r²/1 + r3 ) M (D) (5/6) (r²/1 + r4 ) M

Description : If the ratio of long and short spans of a two way slab with corners held down is r, the actual reduction of B.M. is given by (A) (5/6) (r/1 + r²) M (B) (5/6) (r²/1 + r²) M (C) (5/6) (r²/1 + r3 ) M (D) (5/6) (r²/1 + r4 ) M

Last Answer : Answer: Option D

Long and short spans of a two way slab are ly and lx and load on the slab acting on strips parallel to lx and ly be wx and wy respectively. According to Rankine Grashoff theory (A) (wx /wy ) = (ly /lx ) (B) (wx/wy) = (ly/lx)² (C) (wx /wy ) = (ly /lx )4 (D) None of these

Description : Long and short spans of a two way slab are ly and lx and load on the slab acting on strips parallel to lx and ly be wx and wy respectively. According to Rankine Grashoff theory (A) (wx /wy ) = (ly /lx ) (B) (wx/wy) = (ly/lx)² (C) (wx /wy ) = (ly /lx )4 (D) None of these

Last Answer : Answer: Option C

Which of the following is not a characteristic feature of yield lines? [ A ] Yield lines end at a slab boundary [ B ] Yield lines are of parabolical shape [ C ] Axes of rotation generally lie along the lines of supports [ D ] None of the above.

Description : Which of the following is not a characteristic feature of yield lines? [ A ] Yield lines end at a slab boundary [ B ] Yield lines are of parabolical shape [ C ] Axes of rotation generally lie along the lines of supports [ D ] None of the above.

Last Answer : [ B ] Yield lines are of parabolical shape

In continuous beam if it is end is fixed supported the bending moment will be a. zero b. neglected c. infinite

Description : In continuous beam if it is end is fixed supported the bending moment will be a. zero b. neglected c. infinite

Last Answer : a. zero

In continuous beam if it is end simply supported the bending moment will be a. zero b. neglected c. infinite

Description : In continuous beam if it is end simply supported the bending moment will be a. zero b. neglected c. infinite

Last Answer : a. zero

The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6

Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6

Last Answer : (c) 0.9

In a continuous bending moment curve the point where it changes sign, is called (A) Point of inflexion (B) Point of contraflexure (C) Point of virtual hinge (D) All the above

Description : In a continuous bending moment curve the point where it changes sign, is called (A) Point of inflexion (B) Point of contraflexure (C) Point of virtual hinge (D) All the above

Last Answer : (D) All the above

For a circular slab carrying a uniformly distributed load, the ratio of the maximum negative to maximum positive radial moment, is (A) 1 (B) 2 (C) 3 (D) 5

Description : For a circular slab carrying a uniformly distributed load, the ratio of the maximum negative to maximum positive radial moment, is (A) 1 (B) 2 (C) 3 (D) 5

Last Answer : Answer: Option B

At the supports of a simply supported beam, bending moment will be (a) Maximum (b) Minimum (c) Zero (d) None

Description : At the supports of a simply supported beam, bending moment will be (a) Maximum (b) Minimum (c) Zero (d) None

Last Answer : (c) Zero

What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Last Answer : b. 14.69 N/mm2

What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Last Answer : c. 50.57 N/mm2

A cantilever carrying a uniformly distributed load W over its full length is propped at its free end such that it is at the level of the fixed end. The bending moment will be zero at its free end also at (A) Midpoint of the cantilever (B) Fixed point of the cantilever (C) 1/4th length from free end (D) 3/4th length from free end

Description : A cantilever carrying a uniformly distributed load W over its full length is propped at its free end such that it is at the level of the fixed end. The bending moment will be zero at its free end also at ... point of the cantilever (C) 1/4th length from free end (D) 3/4th length from free end

Last Answer : (D) 3/4th length from free end

A fixed beam with central point load undergoes a slight settlement at one end. Select suitable answer from the following: (a) Moment induced at both ends will be same (b) Moment induced at the end that has undergone settlement will be maximum (c) Moment induced will be maximum at the end having no settlement (d) Zero moment at the end that has settled.

Description : A fixed beam with central point load undergoes a slight settlement at one end. Select suitable answer from the following: (a) Moment induced at both ends will be same (b) Moment induced at the end that ... will be maximum at the end having no settlement (d) Zero moment at the end that has settled.

Last Answer : (c) Moment induced will be maximum at the end having no settlement

When sinking is accounted in a continuous beam the bending moment is a. modified b.same c.zero d.infinite

Description : When sinking is accounted in a continuous beam the bending moment is a. modified b.same c.zero d.infinite

Last Answer : a. modified

In comparison with a simply supported beam of same span and load , a continuous beam has a.less maximum bending moment b. same bending moment c. higher maximum bending moment d. twice the bending moment

Description : In comparison with a simply supported beam of same span and load , a continuous beam has a.less maximum bending moment b. same bending moment c. higher maximum bending moment d. twice the bending moment

Last Answer : a.less maximum bending moment

The surface joining the static levels in several non-pumping wells penetrating a continuous confined aquifer represents (a) Water-table surface (b) Capillary fringe (c) Piezometric surface of the aquifer (d) Physical top surface of the aquifer

Description : The surface joining the static levels in several non-pumping wells penetrating a continuous confined aquifer represents (a) Water-table surface (b) Capillary fringe (c) Piezometric surface of the aquifer (d) Physical top surface of the aquifer

Last Answer : (c) Piezometric surface of the aquifer

A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the bar, is (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm

Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a  load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending  strain energy stored in the ... (A) 411 N mm  (B) 511 N mm  (C) 611 N mm  (D) 711 N mm 

Last Answer : (C) 611 N mm