Pick up the correct statement from the following: (A) The bent up bars at a support resist the negative bending moment (B) The bent up bars at a support resist the sharing force (C) The bending of bars near supports is generally at 45° (D) All the above

Pick up the correct statement from the following:
(A) The bent up bars at a support resist the negative bending moment
(B) The bent up bars at a support resist the sharing force
(C) The bending of bars near supports is generally at 45°
(D) All the above
by

1 Answer

Answer :

(D) All the above
by

Related questions

Pick up the incorrect statement from the following: Tensile reinforcement bars of a rectangular beam (A) Are curtailed if not required to resist the bending moment (B) Are bent up at suitable places to serve as shear reinforcement (C) Are bent down at suitable places to serve as shear reinforcement (D) Are maintained at bottom to provide at least local bond stress

Description : Pick up the incorrect statement from the following: Tensile reinforcement bars of a rectangular beam (A) Are curtailed if not required to resist the bending moment (B) Are bent up at suitable ... to serve as shear reinforcement (D) Are maintained at bottom to provide at least local bond stress

Last Answer : Answer: Option C

Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to resist a sagging bending moment near mid-span. (c) When the slab is built into a brick or masonry wall the slab should be designed to resist a hogging moment at the face of the support. (d) All of the above.

Description : Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to ... be designed to resist a hogging moment at the face of the support. (d) All of the above.

Last Answer : (d) All of the above.

When a slab is continuous over several spans, negative (i.e. hogging ) bending moment is induced over the (a) End supports (b) Intermediate supports (c) Both (a) & (b) (d) Non of the

Description : When a slab is continuous over several spans, negative (i.e. hogging ) bending moment is induced over the (a) End supports (b) Intermediate supports (c) Both (a) & (b) (d) Non of the

Last Answer : (b) Intermediate supports

Pick up the correct statement from the following: (A) The rate of change of bending moment is equal to rate of shear force (B) The rate of change of shear force is equal to rate of loading (C) Neither (a) nor (b)(D) Both (a) and (b

Description : Pick up the correct statement from the following: (A) The rate of change of bending moment is equal to rate of shear force (B) The rate of change of shear force is equal to rate of loading (C) Neither (a) nor (b) (D) Both (a) and (b

Last Answer : (D) Both (a) and (b

The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force

Description : The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force

Last Answer : Answer: Option B

The amount of reinforcement for main bars in a slab, is based upon (a) Maximum bending moment (b) Minimum bending moment (c) Maximum shear force (d) Minimum shear force

Description : The amount of reinforcement for main bars in a slab, is based upon (a) Maximum bending moment (b) Minimum bending moment (c) Maximum shear force (d) Minimum shear force

Last Answer : (a) Maximum bending moment

Bending moment at supports in case of simply supported beam is always (a) Zero (b) Positive (c) Negative (d) Depends upon loading

Description : Bending moment at supports in case of simply supported beam is always (a) Zero (b) Positive (c) Negative (d) Depends upon loading

Last Answer : (a) Zero

The main reason for providing number of reinforcing bars at a support in a simply supported beam is to resist in that zone (A) Compressive stress (B) Shear stress (C) Bond stress (D) Tensile stress

Description : The main reason for providing number of reinforcing bars at a support in a simply supported beam is to resist in that zone (A) Compressive stress (B) Shear stress (C) Bond stress (D) Tensile stress

Last Answer : Answer: Option C

Pick up the incorrect statement from the following: (A) The retaining wall should be structurally capable to resist the applied earth pressure (B) The section of the retaining wall should be so proportioned that it may not overturn by the lateral pressure (C) The retaining wall should be safe against sliding (D) To drain off water from the earth retained, weep holes are provided near the top of the retaining wall

Description : Pick up the incorrect statement from the following: (A) The retaining wall should be structurally capable to resist the applied earth pressure (B) The section of the retaining wall should be so ... off water from the earth retained, weep holes are provided near the top of the retaining wall

Last Answer : Answer: Option D

For a simply supported beam with a central load, the bending moment is (A) Least at the centre (B) Least at the supports (C) Maximum at the supports (D) Maximum at the centre

Description : For a simply supported beam with a central load, the bending moment is  (A) Least at the centre  (B) Least at the supports  (C) Maximum at the supports  (D) Maximum at the centre

Last Answer : (D) Maximum at the centre

The maximum bending moment due to a moving load on a simply supported beam, occurs (A) At the mid span (B) At the supports (C) Under the load (D) Anywhere on the beam

Description : The maximum bending moment due to a moving load on a simply supported beam, occurs (A) At the mid span (B) At the supports (C) Under the load (D) Anywhere on the beam

Last Answer : (C) Under the load

For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Description : For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) The moment of inertia is calculated about the axis about which bending takes place (B) If tensile stress is less than axial stress, the section experiences compressive stress (C) If tensile stress is equal to axial stress, the section experiences compressive stress (D) All the above

Description : Pick up the correct statement from the following:  (A) The moment of inertia is calculated about the axis about which bending takes place  (B) If tensile stress is less than axial ... tensile stress is equal to axial stress, the section experiences compressive stress  (D) All the above 

Last Answer : (D) All the above 

When the steel bars are embedded in concrete. The concrete after setting, adheres to the surface of the bars and thus resist any force that tends to pull or push this road. The intensity of this adhesive force is called. (a) Bond stress (b) Shear stress (c) Compressive stress (d) All of these

Description : When the steel bars are embedded in concrete. The concrete after setting, adheres to the surface of the bars and thus resist any force that tends to pull or push this road. The intensity of this adhesive force is called. (a) Bond stress (b) Shear stress (c) Compressive stress (d) All of these

Last Answer : (a) Bond stress

These bends are caused by excessive pressure and tension and generally occur while fiber are bent during handling or installation. ∙ A. microbending ∙ B. macrobending ∙ C. constant-radius bending ∙ D. kinks

Description : These bends are caused by excessive pressure and tension and generally occur while fiber are bent during handling or installation. ∙ A. microbending ∙ B. macrobending ∙ C. constant-radius bending ∙ D. kinks

Last Answer : C. constant-radius bending

Pick up the correct statement from the following: (A) Higher the gauge, more deficient will be the rain catch (B) Heavier the rain, lesser will be the rain catch (C) The trees serving as wind brakes in the vicinity of the gauge, should not subtend angles greater than 45° (D) All the above

Description : Pick up the correct statement from the following: (A) Higher the gauge, more deficient will be the rain catch (B) Heavier the rain, lesser will be the rain catch (C) The trees serving as wind brakes in the vicinity of the gauge, should not subtend angles greater than 45° (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: Method of sawing timber (A) Tangentially to annual rings, is known as tangential method (B) In four quarters such that each board cuts annual rings at angles not less than 45°, is known as quarter sawing method (C) Cut out of quarter logs, parallel to the medullary rays and perpendicular to annual rings, is known as radial sawing (D) All the above

Description : Pick up the correct statement from the following: Method of sawing timber (A) Tangentially to annual rings, is known as tangential method (B) In four quarters such that each board cuts annual rings ... medullary rays and perpendicular to annual rings, is known as radial sawing (D) All the above

Last Answer : Answer: Option D

A member is balanced at its end by two inclined members carrying equal forces. For equilibrium the angle between the inclined bars must be (A) 3° (B) 45° (C) 90° (D) 120°

Description : A member is balanced at its end by two inclined members carrying equal forces. For equilibrium  the angle between the inclined bars must be  (A) 3°  (B) 45°  (C) 90°  (D) 120° 

Last Answer : (D) 120° 

If the size of a column is reduced above the floor, the main bars of the columns, are (A) Continued up (B) Bent inward at the floor level (C) Stopped just below the floor level and separate lap bars provided (D) All the above

Description : If the size of a column is reduced above the floor, the main bars of the columns, are (A) Continued up (B) Bent inward at the floor level (C) Stopped just below the floor level and separate lap bars provided (D) All the above

Last Answer : Answer: Option D

Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ A ] i

At the supports of a simply supported beam, bending moment will be (a) Maximum (b) Minimum (c) Zero (d) None

Description : At the supports of a simply supported beam, bending moment will be (a) Maximum (b) Minimum (c) Zero (d) None

Last Answer : (c) Zero

Pick up the correct statement from the following: (A) Large solids carried along the river bed, is known as bed load (B) The fine sediment deposits are generally near the face of the dam (C) Deposition of sediment in the reservoir, reduces the capacity of the reservoir (D) All the above

Description : Pick up the correct statement from the following:  (A) Large solids carried along the river bed, is known as bed load  (B) The fine sediment deposits are generally near the face of ... ) Deposition of sediment in the reservoir, reduces the capacity of the reservoir  (D) All the above 

Last Answer : (D) All the above 

A stirrups consists of ____________diameter mildsteel bars bent round the tensile reinforcement (a) 1 to 5mm (b) 5 to 12mm (c) 12 to 18mm (d) All the above

Description : A stirrups consists of ____________diameter mildsteel bars bent round the tensile reinforcement (a) 1 to 5mm (b) 5 to 12mm (c) 12 to 18mm (d) All the above

Last Answer : (b) 5 to 12mm

Pick up the correct statement from the following: (A) The free quartz suddenly expands at a temperature lower than 600°C (B) The lime stone resists fire upto about 800°C and at higher temperature it splits into CaO and CO2 (C) The sand stone with silicates resist a fire in a better way (D) All the above

Description : Pick up the correct statement from the following: (A) The free quartz suddenly expands at a temperature lower than 600°C (B) The lime stone resists fire upto about 800°C and at higher temperature it splits into ... (C) The sand stone with silicates resist a fire in a better way (D) All the above

Last Answer : Answer: Option D

In the slope deflection equations, the deformations are considered to be caused by (i) Bending moment (ii) Shear force (iii) Axial force The correct answer is (A) Only (i) (B) (i) and (ii) (C) (ii) and (iii) (D) (i), (ii) and (iii)

Description : In the slope deflection equations, the deformations are considered to be caused by (i) Bending moment (ii) Shear force (iii) Axial force The correct answer is (A) Only (i) (B) (i) and (ii) (C) (ii) and (iii) (D) (i), (ii) and (iii)

Last Answer : (A) Only (i)

The zone in which transverse bending is likely to occur may be obtained by drawing a line from the (A) 30° (B) 45° (C) 60° (D) None of these

Description : The zone in which transverse bending is likely to occur may be obtained by drawing a line from the (A) 30° (B) 45° (C) 60° (D) None of these

Last Answer : Answer: Option B

If the positive and negative shear force diagram areas are not equal, it can be concluded that a.shear force diagram has been wrongly drawn b.there is at least one couple acting on the beam c.107 dynes d.there are at least two maxima for bending moment e.bending moment does not change sign

Description : If the positive and negative shear force diagram areas are not equal, it can be concluded that a.shear force diagram has been wrongly drawn b.there is at least one couple acting on the beam c.107 dynes d.there are at least two maxima for bending moment e.bending moment does not change sign

Last Answer : b. there is at least one couple acting on the beam

The concavity produced on the beam section about the centre line when downward force acts on it is called as (a) Hogging or positive bending moment (b) Hogging or negative bending moment (c) Sagging or positive bending moment (d) Sagging or negative bending moment

Description : The concavity produced on the beam section about the centre line when downward force acts on it is called as (a) Hogging or positive bending moment (b) Hogging or negative bending moment (c) Sagging or positive bending moment (d) Sagging or negative bending moment

Last Answer : (b) Hogging or negative bending moment

Point of contra-flexure is a (a) Point where Shear force is maximum (b) Point where Bending moment is maximum (c) Point where Bending moment is zero (d) Point where Bending moment=0 but also changes sign from positive to negative

Description : Point of contra-flexure is a (a) Point where Shear force is maximum (b) Point where Bending moment is maximum (c) Point where Bending moment is zero (d) Point where Bending moment=0 but also changes sign from positive to negative

Last Answer : (d) Point where Bending moment=0 but also changes sign from positive to negative

In a singly reinforced concrete beam, as the load increases. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete and steel will resist tension. (d) Both concrete and steel will resist compression.

Description : In a singly reinforced concrete beam, as the load increases. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete and steel will resist tension. (d) Both concrete and steel will resist compression.

Last Answer : (b) Only steel bars will resist tension.

In a singly reinforced concrete beam, if the load is vey small. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete & steel will resist tension. (d) Both concrete & steel will resist compression.

Description : In a singly reinforced concrete beam, if the load is vey small. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete & steel will resist tension. (d) Both concrete & steel will resist compression.

Last Answer : (c) Both concrete & steel will resist tension.

If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than (A) WL/12 (L - 2D/3)² (B) WL/10 (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Description : If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span ... (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Last Answer : Answer: Option C

When load is applied on concrete pavement (A) Away from edges, the maximum bending moment is negative (B) Away from edges, the maximum bending moment cause compression (C) On the edges, the maximum stress is parallel to the edge of the slab (D) None of these

Description : When load is applied on concrete pavement (A) Away from edges, the maximum bending moment is negative (B) Away from edges, the maximum bending moment cause compression (C) On the edges, the maximum stress is parallel to the edge of the slab (D) None of these

Last Answer : Answer: Option C

A simply supported beam carries two equal concentrated loads W at distances L/3 from either support. The maximum bending moment (A) WL/3 (B) WL/4 (C) 5WL/4 (D) 3WL/12

Description : A simply supported beam carries two equal concentrated loads W at distances L/3 from either support. The maximum bending moment (A) WL/3 (B) WL/4 (C) 5WL/4 (D) 3WL/12

Last Answer : (A) WL/3

Consider the following statements: Sinking of an intermediate support of a continuous beam 1. Reduces the negative moment at support. 2. Increases the negative moment at support. 3. Reduces the positive moment at support. 4. Increases the positive moment at the centre of span. Of these statements (A) 1 and 4 are correct (B) 1 and 3 are correct (C) 2 and 3 are correct (D) 2 and 4 are correct

Description : Consider the following statements: Sinking of an intermediate support of a continuous beam 1. Reduces the negative moment at support. 2. Increases the negative moment at support. 3. Reduces the positive moment at ... 1 and 3 are correct (C) 2 and 3 are correct (D) 2 and 4 are correct

Last Answer : (A) 1 and 4 are correct

Sinking of an intermediate support of a continuous beam (i) Reduces the negative moment at support (ii) Increases the negative moment at support (iii) Reduces the positive moment at center of span (iv) Increases the positive moment at center of span The correct answer is (A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Description : Sinking of an intermediate support of a continuous beam (i) Reduces the negative moment at support (ii) Increases the negative moment at support (iii) Reduces the positive moment at center of span (iv) Increases the positive moment ... (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Last Answer : Answer: Option B

The bending moment is maximum on a section where shearing force (A) Is maximum (B) Is minimum (C) Is equal (D) Changes sign

Description : The bending moment is maximum on a section where shearing force  (A) Is maximum  (B) Is minimum  (C) Is equal  (D) Changes sign 

Last Answer : (D) Changes sign 

If the shear force along a section of a beam is zero, the bending moment at the section is (A) Zero (B) Maximum (C) Minimum (D) Average of maximum-minimum

Description : If the shear force along a section of a beam is zero, the bending moment at the section is  (A) Zero  (B) Maximum  (C) Minimum  (D) Average of maximum-minimum 

Last Answer : (B) Maximum 

An arch may be subjected to (A) Shear and axial force (B) Bending moment and shear force (C) Bending moment and axial force (D) Thrust, shear force and bending moment

Description : An arch may be subjected to  (A) Shear and axial force  (B) Bending moment and shear force  (C) Bending moment and axial force  (D) Thrust, shear force and bending moment 

Last Answer : (D) Thrust, shear force and bending moment 

A diagram which shows the variations of the axial load for all sections of the span of a beam, is called (A) Bending moment diagram (B) Shear force diagram (C) Thrust diagram (D) Stress diagram

Description : A diagram which shows the variations of the axial load for all sections of the span of a beam, is called (A) Bending moment diagram (B) Shear force diagram (C) Thrust diagram (D) Stress diagram

Last Answer : Answer: Option C

In a loaded beam, the point of contraflexure occurs at a section where (A) Bending moment is minimum (B) Bending moment is zero or changes sign (C) Bending moment is maximum (D) Shearing force is maximum

Description : In a loaded beam, the point of contraflexure occurs at a section where (A) Bending moment is minimum (B) Bending moment is zero or changes sign (C) Bending moment is maximum (D) Shearing force is maximum

Last Answer : Answer: Option B

If Z and I are the section modulus and moment of inertia of the section, the shear force F and bending moment M at a section are related by (A) F = My/I (B) F = M/Z (C) F = dM/dx (D) F Mdx

Description : If Z and I are the section modulus and moment of inertia of the section, the shear force F and bending moment M at a section are related by (A) F = My/I (B) F = M/Z (C) F = dM/dx (D) F Mdx

Last Answer : (C) F = dM/dx

If a three hinged parabolic arch carries a uniformly distributed load on its entire span, every section of the arch resists. (A) Compressive force (B) Tensile force (C) Shear force (D) Bending moment

Description : If a three hinged parabolic arch carries a uniformly distributed load on its entire span, every section of the arch resists. (A) Compressive force (B) Tensile force (C) Shear force (D) Bending moment

Last Answer : (A) Compressive force

In a combined footing for two columns carrying unequal loads, the maximum hogging bending moment occurs at (A) Less loaded column (B) More loaded column (C) A point of the maximum shear force (D) A point of zero shear force

Description : In a combined footing for two columns carrying unequal loads, the maximum hogging bending moment occurs at (A) Less loaded column (B) More loaded column (C) A point of the maximum shear force (D) A point of zero shear force

Last Answer : Answer: Option D

In a beam the local bond stress Sb, is equal to (A) Shear force/(Leaver arm × Total perimeter of reinforcement) (B) Total perimeter of reinforcement/(Leaver arm × Shear force) (C) Leaver arm/(Shear force × Total perimeter of reinforcement) (D) Leaver arm/(Bending moment × Total perimeter of reinforcement)

Description : In a beam the local bond stress Sb, is equal to (A) Shear force/(Leaver arm Total perimeter of reinforcement) (B) Total perimeter of reinforcement/(Leaver arm Shear force) (C) ... force Total perimeter of reinforcement) (D) Leaver arm/(Bending moment Total perimeter of reinforcement)

Last Answer : Answer: Option A

is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The maximum stress in the beam, subjected to a maximum bending moment , is (A) f = (P/A) + (Z/M) (B) f = (A/P) + (M/Z) (C) f = (P/A) + (M/Z) (D) f = (P/A) + (M/6Z)

Description : is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The maximum stress in the beam, subjected to a maximum bending moment , is (A) f = (P/A) + (Z/M) ... ) + (M/Z) (C) f = (P/A) + (M/Z) (D) f = (P/A) + (M/6Z)

Last Answer : Answer: Option C

is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is (A) f = (P/A) - (Z/M) (B) f = (A/P) - (M/Z) (C) f = (P/A) - (M/Z) (D) f = (P/A) - (M/6Z)

Description : is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is (A) f = (P/A) - (Z/M) (B) f = (A/P) - (M/Z) (C) f = (P/A) - (M/Z) (D) f = (P/A) - (M/6Z)

Last Answer : Answer: Option C

A construction joint is provided where (A) Bending moment is small (B) Shear force is small (C) The member is supported by other member (D) All the above

Description : A construction joint is provided where (A) Bending moment is small (B) Shear force is small (C) The member is supported by other member (D) All the above

Last Answer : Answer: Option D

For a certain set of external loads, concordant profile in a prestressed beam represents to some scale the (a) Influence line diagram (b) Shear force diagram (c) Bending moment diagram (d) Williot-Mohr diagram

Description : For a certain set of external loads, concordant profile in a prestressed beam represents to some scale the (a) Influence line diagram (b) Shear force diagram (c) Bending moment diagram (d) Williot-Mohr diagram

Last Answer : (c) Bending moment diagram

In prestressed concrete members, the shear force depends upon (a) Distributed load (b) Torsion (c) Concentrated load (d) Variation in net bending moment

Description : In prestressed concrete members, the shear force depends upon (a) Distributed load (b) Torsion (c) Concentrated load (d) Variation in net bending moment

Last Answer : (d) Variation in net bending moment