Sinking of an intermediate support of a continuous beam (i) Reduces the negative moment at support (ii) Increases the negative moment at support (iii) Reduces the positive moment at center of span (iv) Increases the positive moment at center of span The correct answer is (A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Sinking of an intermediate support of a continuous beam
 (i) Reduces the negative moment at support
 (ii) Increases the negative moment at support
 (iii) Reduces the positive moment at center of span
 (iv) Increases the positive moment at center of span
 The correct answer is
(A) (i) and (iii)
(B) (i) and (iv)
(C) (ii) and (iii)
(D) (ii) and (iv)
by

1 Answer

Answer :

Answer: Option B
by

Related questions

Consider the following statements: Sinking of an intermediate support of a continuous beam 1. Reduces the negative moment at support. 2. Increases the negative moment at support. 3. Reduces the positive moment at support. 4. Increases the positive moment at the centre of span. Of these statements (A) 1 and 4 are correct (B) 1 and 3 are correct (C) 2 and 3 are correct (D) 2 and 4 are correct

Description : Consider the following statements: Sinking of an intermediate support of a continuous beam 1. Reduces the negative moment at support. 2. Increases the negative moment at support. 3. Reduces the positive moment at ... 1 and 3 are correct (C) 2 and 3 are correct (D) 2 and 4 are correct

Last Answer : (A) 1 and 4 are correct

In continuous beam with couple , the couple will cause a. negative moment in one part and positive moment in other part of the span b. negative moment in both part of the span c. no moment d. positive moment in both part of the span

Description : In continuous beam with couple , the couple will cause a. negative moment in one part and positive moment in other part of the span b. negative moment in both part of the span c. no moment d. positive moment in both part of the span

Last Answer : a. negative moment in one part and positive moment in other part of the span b. negative moment in both part of the span

In a ring beam subjected to uniformly distributed load (i) Shear force at mid span is zero (ii) Shear force at mid span is maximum (iii) Torsion at mid span is zero (iv) Torsion at mid span is maximum The correct answer is (A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Description : In a ring beam subjected to uniformly distributed load (i) Shear force at mid span is zero (ii) Shear force at mid span is maximum (iii) Torsion at mid span is zero (iv) Torsion at mid span is maximum The correct answer ... and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Last Answer : Option A

When sinking is accounted in a continuous beam the bending moment is a. modified b.same c.zero d.infinite

Description : When sinking is accounted in a continuous beam the bending moment is a. modified b.same c.zero d.infinite

Last Answer : a. modified

Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ A ] i

While using three moments equation, a fixed end of a continuous beam is replaced by an additional span of (A) Zero length (B) Infinite length (C) Zero moment of inertia(D) None of the above

Description : While using three moments equation, a fixed end of a continuous beam is replaced by an additional span of (A) Zero length (B) Infinite length (C) Zero moment of inertia (D) None of the above

Last Answer : (A) Zero length

For stable structures, one of the important properties of flexibility and stiffness matrices is that the elements on the main diagonal (i) Of a stiffness matrix must be positive (ii) Of a stiffness matrix must be negative (iii) Of a flexibility matrix must be positive (iv) Of a flexibility matrix must be negative The correct answer is (A) (i) and (iii) (B) (ii) and (iii) (C) (i) and (iv) (D) (ii) and (iv)

Description : For stable structures, one of the important properties of flexibility and stiffness matrices is that the elements on the main diagonal (i) Of a stiffness matrix must be positive (ii) Of a stiffness matrix must be negative (iii) Of ... ) (B) (ii) and (iii) (C) (i) and (iv) (D) (ii) and (iv)

Last Answer : (A) (i) and (iii)

When a slab is continuous over several spans, negative (i.e. hogging ) bending moment is induced over the (a) End supports (b) Intermediate supports (c) Both (a) & (b) (d) Non of the

Description : When a slab is continuous over several spans, negative (i.e. hogging ) bending moment is induced over the (a) End supports (b) Intermediate supports (c) Both (a) & (b) (d) Non of the

Last Answer : (b) Intermediate supports

In the design of a front counterfort in a counterfort retaining wall, the main reinforcement is provided on (i) Bottom face near counterfort (ii) Top face near counterfort (iii) Bottom face near centre of span (iv) Top face near centre of span The correct answer is (A) Only (i) (B) Only (ii) (C) Both (i) and (iv) (D) Both (ii) and (iii)

Description : In the design of a front counterfort in a counterfort retaining wall, the main reinforcement is provided on (i) Bottom face near counterfort (ii) Top face near counterfort (iii) Bottom face near centre of span (iv) Top ... ) (B) Only (ii) (C) Both (i) and (iv) (D) Both (ii) and (iii)

Last Answer : Answer: Option C

In continuous beam, the intermediate beams are subjected to a. some bending moment b. no bending moment c. no slope d.no deflection

Description : In continuous beam, the intermediate beams are subjected to a. some bending moment b. no bending moment c. no slope d.no deflection

Last Answer : a. some bending moment

In counterfort type retaining walls (i) The vertical slab is designed as a continuous slab (ii) The heel slab is designed as a continuous slab (iii) The vertical slab is designed as a cantilever (iv) The heel slab is designed as a cantilever The correct answer is (A) (i) and (ii) (B) (i)and(iv) (C) (ii) and (iii) (D) (iii) and (iv)

Description : In counterfort type retaining walls (i) The vertical slab is designed as a continuous slab (ii) The heel slab is designed as a continuous slab (iii) The vertical slab is designed as a cantilever (iv) The heel slab is designed ... (ii) (B) (i)and(iv) (C) (ii) and (iii) (D) (iii) and (iv)

Last Answer : Answer: Option A

In comparison with a simply supported beam of same span and load , a continuous beam has a.less maximum bending moment b. same bending moment c. higher maximum bending moment d. twice the bending moment

Description : In comparison with a simply supported beam of same span and load , a continuous beam has a.less maximum bending moment b. same bending moment c. higher maximum bending moment d. twice the bending moment

Last Answer : a.less maximum bending moment

For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9

Description : For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9

Last Answer : Answer: Option D

If the length of an intermediate span of a continuous slab is 5m, the length of the end span is kept (A) 4.5 m (B) 4.0 m (C) 3.5 m (D) 3.0 m

Description : If the length of an intermediate span of a continuous slab is 5m, the length of the end span is kept (A) 4.5 m (B) 4.0 m (C) 3.5 m (D) 3.0 m

Last Answer : Answer: Option A

If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than (A) WL/12 (L - 2D/3)² (B) WL/10 (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Description : If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span ... (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Last Answer : Answer: Option C

When sinking is accounted in a continuous beam the shear force is a.modified b.same c.zero d.infinite

Description : When sinking is accounted in a continuous beam the shear force is a.modified b.same c.zero d.infinite

Last Answer : a.modified

Which one of the following is the correct ratio of plastic moment to yield moment for a simply supported beam of uniform square cross section throughout the span (a) 1.5 (b) 1.7 (c) 2.0 (d) 2.34

Description : Which one of the following is the correct ratio of plastic moment to yield moment for a simply supported beam of uniform square cross section throughout the span (a) 1.5 (b) 1.7 (c) 2.0 (d) 2.34

Last Answer : (a) 1.5

A continuous beam shall be deemed to be a deep beam if the ratio of effective span to overall depth, is (A) 2.5 (B) 2.0 (C) Less than 2 (D) Less than 2.5

Description : A continuous beam shall be deemed to be a deep beam if the ratio of effective span to overall depth, is (A) 2.5 (B) 2.0 (C) Less than 2 (D) Less than 2.5

Last Answer : Answer: Option A

If the ratio of the span to the overall depth does not exceed 10, the stiffness of the beam will ordinarily be satisfactory in case of a (A) Simply supported beam (B) Continuous beam (C) Cantilever beam (D) None of these

Description : If the ratio of the span to the overall depth does not exceed 10, the stiffness of the beam will ordinarily be satisfactory in case of a (A) Simply supported beam (B) Continuous beam (C) Cantilever beam (D) None of these

Last Answer : Answer: Option C

A continuous beam is deemed to be a deep beam when the ratio of effective span to overall depth (1/D) is less than (A) 1.5 (B) 2.0 (C) 2.5 (D) 3.0

Description : A continuous beam is deemed to be a deep beam when the ratio of effective span to overall depth (1/D) is less than (A) 1.5 (B) 2.0 (C) 2.5 (D) 3.0

Last Answer : Answer: Option C

Presence of tail water in a gravity dam (i) Increases the principal stress (ii) Decreases the principal stress (iii) Increases the shear stress (iv) Decreases the shear stress The correct answer isA) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Description : Presence of tail water in a gravity dam (i) Increases the principal stress (ii) Decreases the principal stress (iii) Increases the shear stress (iv) Decreases the shear stress The correct answer is A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Last Answer : Answer: Option D

A concentrated load P acts on a simply supported beam of span L at a distance L/3 from the left support. The bending moment at the point of application of the load is given by (a) PL/3 (b) 2PL/3 (c) PL/9 (d) 2PL/9

Description : A concentrated load P acts on a simply supported beam of span L at a distance L/3 from the left support. The bending moment at the point of application of the load is given by (a) PL/3 (b) 2PL/3 (c) PL/9 (d) 2PL/9

Last Answer : (d) 2PL/9

The moments developed in the slab are influenced by the following factors i.Short span ii.Long span iii.Type of supporting edge. iv.Magnitude and type of load on slab [ A ] i, iii and iv [ B ] ii ,iii and iv [ C ] i and iii [ D ] i, ii , iii and iv

Description : The moments developed in the slab are influenced by the following factors i.Short span ii.Long span iii.Type of supporting edge. iv.Magnitude and type of load on slab [ A ] i, iii and iv [ B ] ii ,iii and iv [ C ] i and iii [ D ] i, ii , iii and iv

Last Answer : [ D ] i, ii , iii and iv

Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to resist a sagging bending moment near mid-span. (c) When the slab is built into a brick or masonry wall the slab should be designed to resist a hogging moment at the face of the support. (d) All of the above.

Description : Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to ... be designed to resist a hogging moment at the face of the support. (d) All of the above.

Last Answer : (d) All of the above.

A simply supported beam of span carries a uniformly distributed load . The maximum bending moment is (A) WL/2 (B) WL/4 (C) WL/8 (D) WL/12

Description : A simply supported beam of span carries a uniformly distributed load . The maximum bending moment is (A) WL/2 (B) WL/4 (C) WL/8 (D) WL/12

Last Answer : (C) WL/8

A simply supported beam of span L carries a concentrated load W at its mid-span. The maximum bending moment M is (A) WL/2 (B) WL/4 (C) WL/8 (D) WL/12

Description : A simply supported beam of span L carries a concentrated load W at its mid-span. The maximum  bending moment M is  (A) WL/2  (B) WL/4  (C) WL/8  (D) WL/12

Last Answer : (B) WL/4

A diagram which shows the variations of the axial load for all sections of the span of a beam, is called (A) Bending moment diagram (B) Shear force diagram (C) Thrust diagram (D) Stress diagram

Description : A diagram which shows the variations of the axial load for all sections of the span of a beam, is called (A) Bending moment diagram (B) Shear force diagram (C) Thrust diagram (D) Stress diagram

Last Answer : Answer: Option C

The maximum bending moment due to a moving load on a simply supported beam, occurs (A) At the mid span (B) At the supports (C) Under the load (D) Anywhere on the beam

Description : The maximum bending moment due to a moving load on a simply supported beam, occurs (A) At the mid span (B) At the supports (C) Under the load (D) Anywhere on the beam

Last Answer : (C) Under the load

In continuous beam between intermediate supports the deflection is a. convex down b. convex up c. concave up d. concave down

Description : In continuous beam between intermediate supports the deflection is a. convex down b. convex up c. concave up d. concave down

Last Answer : b. convex up

Differentiate between positive and negative feedback on the basis of . (i) overall phase shift (ii) voltage gain (iii) stability (iv) applications

Description : Differentiate between positive and negative feedback on the basis of . (i) overall phase shift (ii) voltage gain (iii) stability (iv) applications 

Last Answer : Compare positive feedback and negative feedback on the basis of: (i) Gain (ii) Bandwidth (iii) Phase shift (iv) Stability

If a continuous beam is fixed on the right then the imaginary span is taken a.before the right end b. after the right end c. before the left end d. after the left end

Description : If a continuous beam is fixed on the right then the imaginary span is taken a.before the right end b. after the right end c. before the left end d. after the left end

Last Answer : b. after the right end

If the positive and negative shear force diagram areas are not equal, it can be concluded that a.shear force diagram has been wrongly drawn b.there is at least one couple acting on the beam c.107 dynes d.there are at least two maxima for bending moment e.bending moment does not change sign

Description : If the positive and negative shear force diagram areas are not equal, it can be concluded that a.shear force diagram has been wrongly drawn b.there is at least one couple acting on the beam c.107 dynes d.there are at least two maxima for bending moment e.bending moment does not change sign

Last Answer : b. there is at least one couple acting on the beam

The concavity produced on the beam section about the centre line when downward force acts on it is called as (a) Hogging or positive bending moment (b) Hogging or negative bending moment (c) Sagging or positive bending moment (d) Sagging or negative bending moment

Description : The concavity produced on the beam section about the centre line when downward force acts on it is called as (a) Hogging or positive bending moment (b) Hogging or negative bending moment (c) Sagging or positive bending moment (d) Sagging or negative bending moment

Last Answer : (b) Hogging or negative bending moment

Bending moment at supports in case of simply supported beam is always (a) Zero (b) Positive (c) Negative (d) Depends upon loading

Description : Bending moment at supports in case of simply supported beam is always (a) Zero (b) Positive (c) Negative (d) Depends upon loading

Last Answer : (a) Zero

In the slope deflection equations, the deformations are considered to be caused by (i) Bending moment (ii) Shear force (iii) Axial force The correct answer is (A) Only (i) (B) (i) and (ii) (C) (ii) and (iii) (D) (i), (ii) and (iii)

Description : In the slope deflection equations, the deformations are considered to be caused by (i) Bending moment (ii) Shear force (iii) Axial force The correct answer is (A) Only (i) (B) (i) and (ii) (C) (ii) and (iii) (D) (i), (ii) and (iii)

Last Answer : (A) Only (i)

Define following terms: i) Economic span ii) Afflux iii) Waterway iv) Free board

Description : Define following terms: i) Economic span ii) Afflux iii) Waterway iv) Free board

Last Answer : i) Economic span: The span for which the total cost of the bridge is minimum is known as economical span of a bridge. ii) Afflux: It is the rise in water surface caused due to the obstruction ... , if any, and the lowest point on the underside of the bridge super structure is called free board.

The methods used for locating the plane table stations are (i) Radiation (ii) Traversing (iii) Intersection (iv) Resection The correct answer is (A) (i) and (ii) (B) (iii) and (iv) (C) (ii) and (iv) (D) (i) and (iii)

Description : The methods used for locating the plane table stations are (i) Radiation (ii) Traversing (iii) Intersection (iv) Resection The correct answer is (A) (i) and (ii) (B) (iii) and (iv) (C) (ii) and (iv) (D) (i) and (iii)

Last Answer : (C) (ii) and (iv)

Muller Breslau's principle for obtaining influence lines is applicable to (i) Trusses (ii) Statically determinate beams and frames (iii) Statically indeterminate structures, the material of which is elastic and follows Hooke's law (iv) Any statically indeterminate structure The correct answer is (A) (i), (ii) and (iii) (B) (i), (ii) and (iv) (C) (i) and (ii) (D) Only (i)

Description : Muller Breslau's principle for obtaining influence lines is applicable to (i) Trusses (ii) Statically determinate beams and frames (iii) Statically indeterminate structures, the material of which is elastic and follows Hooke's law (iv ... B) (i), (ii) and (iv) (C) (i) and (ii) (D) Only (i)

Last Answer : (A) (i), (ii) and (iii)

Study the following statements. (i) Levees are constructed parallel to river flow (ii) Spurs are constructed parallel to river flow (iii) Levees are constructed transverse to river flow (iv) Spurs are constructed transverse to river flow The correct answer is (A) (i) and (ii) (B) (i) and (iv) (C) (ii) and (iii) (D) (iii) and (iv)

Description : Study the following statements. (i) Levees are constructed parallel to river flow (ii) Spurs are constructed parallel to river flow (iii) Levees are constructed transverse to river flow (iv) Spurs are constructed transverse to ... (B) (i) and (iv) (C) (ii) and (iii) (D) (iii) and (iv)

Last Answer : Answer: Option B

Instantaneous unit hydrograph is a hydrograph of (i) Unit duration (ii) Unit rainfall excess (iii) Infinitely small duration (iv) Infinitely small rainfall excess The correct answer is (A) (i) and (ii) (B) (i) and (iv) C) (ii) and (iii) (D) (iii) and (iv)

Description : Instantaneous unit hydrograph is a hydrograph of (i) Unit duration (ii) Unit rainfall excess (iii) Infinitely small duration (iv) Infinitely small rainfall excess The correct answer is (A) (i) and (ii) (B) (i) and (iv) C) (ii) and (iii) (D) (iii) and (iv)

Last Answer : Answer: Option C

method requires the following data pertaining annual flood series (i) Mean value (ii) Standard deviation (iii) Length of record (iv) Coefficient of skew The correct answer is (A) (i) and (ii) (B) (i),(i) and (iii) (C) (i), (ii) and (iv) (D) (i), (ii), (iii) and (iv)

Description : method requires the following data pertaining annual flood series (i) Mean value (ii) Standard deviation (iii) Length of record (iv) Coefficient of skew The correct answer is (A) (i) and (ii) (B) (i),(i) and (iii) (C) (i), (ii) and (iv) (D) (i), (ii), (iii) and (iv)

Last Answer : Answer: Option B

The effect of adding calcium chloride in concrete is (i) To increase shrinkage (ii) To decrease shrinkage (iii) To increase setting time (iv) To decrease setting time The correct answer is (A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Description : The effect of adding calcium chloride in concrete is (i) To increase shrinkage (ii) To decrease shrinkage (iii) To increase setting time (iv) To decrease setting time The correct answer is (A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Last Answer : (B) (i) and (iv)

The main reinforcement in the toe of a T-shaped R C. retaining wall is provided on (i) Top face parallel to the wall (ii) Top face perpendicular to the wall (iii) Bottom face parallel to the wall (iv) Bottom face perpendicular to the wall The correct answer is (A) Only (ii) is correct (B) (i) and (ii) are correct (C) (iii) and (iv) are correct (D) Only (iv) is correct

Description : The main reinforcement in the toe of a T-shaped R C. retaining wall is provided on (i) Top face parallel to the wall (ii) Top face perpendicular to the wall (iii) Bottom face parallel to the wall (iv) ... (i) and (ii) are correct (C) (iii) and (iv) are correct (D) Only (iv) is correct

Last Answer : Answer: Option D

In a counterfort retaining wall, the main reinforcement is provided on the (i) Bottom face in front counterfort (ii) Inclined face in front counterfort (iii) Bottom face in back counterfort (iv) Inclined face in back counterfort The correct answer is (A) (i) and (ii), (B) (ii) and (iii) (C) (i) and (iv) (D) (iii) and (iv)

Description : In a counterfort retaining wall, the main reinforcement is provided on the (i) Bottom face in front counterfort (ii) Inclined face in front counterfort (iii) Bottom face in back counterfort (iv) Inclined face in back counterfort ... (B) (ii) and (iii) (C) (i) and (iv) (D) (iii) and (iv)

Last Answer : Answer: Option C

Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) (iii) and (iv) (D) (i) and (iv)

Description : Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) (iii) and (iv) (D) (i) and (iv)

Last Answer : Answer: Option D

The TQM initiative reduces material costs and labor costs. a. Concurrent Engineering (CCE)/Six Sigma b. Benchmarking c. Continuous Product Improvement systems (CPI) d. Channel Support systems e. Quality Initiative Training (QIT)

Description : The TQM initiative reduces material costs and labor costs. a. Concurrent Engineering (CCE)/Six Sigma b. Benchmarking c. Continuous Product Improvement systems (CPI) d. Channel Support systems e. Quality Initiative Training (QIT)

Last Answer : a. Concurrent Engineering (CCE)/Six Sigma

These TQM initiatives reduce administrative overhead; reduces the R&D cycle time and enhances the effectiveness of the promotion and sales budget. a. Concurrent Engineering (CCE); Channel Support systems and Just-in-Time Inventory b. Quality Function Deployment and Benchmarking c. Continuous Product Improvement systems (CPI) and Just-in-Time Inventory d. Channel Support systems and Six Sigma e. Quality Initiative Training (QIT)

Description : These TQM initiatives reduce administrative overhead; reduces the R&D cycle time and enhances the effectiveness of the promotion and sales budget. a. Concurrent Engineering (CCE); Channel Support systems ... Inventory d. Channel Support systems and Six Sigma e. Quality Initiative Training (QIT)

Last Answer : b. Quality Function Deployment and Benchmarking

This process management initiative reduces R&D cycle time, a. Concurrent Engineering (CCE) b. Benchmarking c. Continuous Product Improvement systems (CPI) d. Channel Support systems e. Quality Initiative Training (QIT)

Description : This process management initiative reduces R&D cycle time, a. Concurrent Engineering (CCE) b. Benchmarking c. Continuous Product Improvement systems (CPI) d. Channel Support systems e. Quality Initiative Training (QIT)

Last Answer : a. Concurrent Engineering (CCE)

This process management initiative reduces material costs and administrative overhead. a. Benchmarking b. Vendor/Just-in-Time Inventory (JIT) c. Continuous Product Improvement systems (CPI) d. Channel Support systems e. Quality Initiative Training (QIT)

Description : This process management initiative reduces material costs and administrative overhead. a. Benchmarking b. Vendor/Just-in-Time Inventory (JIT) c. Continuous Product Improvement systems (CPI) d. Channel Support systems e. Quality Initiative Training (QIT)

Last Answer : b. Vendor/Just-in-Time Inventory (JIT)