The reinforcement in a continuous slab is provided (a) At the top of the slab portion over the intermediate supports. (b) At the bottom of the slab portion over the intermediate supports. (c) All the middle of the slab portion over the intermediate supports (d) All the above

The reinforcement in a continuous slab is provided
(a) At the top of the slab portion over the intermediate supports.
(b) At the bottom of the slab portion over the intermediate supports.
(c) All the middle of the slab portion over the intermediate supports
(d) All the above
by

1 Answer

Answer :

(a) At the top of the slab portion over the intermediate supports.
by

Related questions

When a slab is continuous over several spans, negative (i.e. hogging ) bending moment is induced over the (a) End supports (b) Intermediate supports (c) Both (a) & (b) (d) Non of the

Description : When a slab is continuous over several spans, negative (i.e. hogging ) bending moment is induced over the (a) End supports (b) Intermediate supports (c) Both (a) & (b) (d) Non of the

Last Answer : (b) Intermediate supports

Pick up the incorrect statement from the following: (A) In the stem of a retaining wall, reinforcement is provided near the earth side (B) In the toe slab of a retaining wall, reinforcement is provided at the bottom of the slab (C) In the heel slab of a retaining wall, reinforcement is provided at the top of the slab (D) None of these

Description : Pick up the incorrect statement from the following: (A) In the stem of a retaining wall, reinforcement is provided near the earth side (B) In the toe slab of a retaining wall, reinforcement is ... slab of a retaining wall, reinforcement is provided at the top of the slab (D) None of these

Last Answer : Answer: Option D

An R.C.C. roof slab is designed as a two way slab if (A) It supports live loads in both directions (B) The ratio of spans in two directions is less than 2 (C) The slab is continuous over two supports (D) The slab is discontinuous at edges

Description : An R.C.C. roof slab is designed as a two way slab if (A) It supports live loads in both directions (B) The ratio of spans in two directions is less than 2 (C) The slab is continuous over two supports (D) The slab is discontinuous at edges

Last Answer : Answer: Option B

Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ A ] i

For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9

Description : For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9

Last Answer : Answer: Option D

If the length of an intermediate span of a continuous slab is 5m, the length of the end span is kept (A) 4.5 m (B) 4.0 m (C) 3.5 m (D) 3.0 m

Description : If the length of an intermediate span of a continuous slab is 5m, the length of the end span is kept (A) 4.5 m (B) 4.0 m (C) 3.5 m (D) 3.0 m

Last Answer : Answer: Option A

The main reinforcement in the toe of a T-shaped R C. retaining wall is provided on (i) Top face parallel to the wall (ii) Top face perpendicular to the wall (iii) Bottom face parallel to the wall (iv) Bottom face perpendicular to the wall The correct answer is (A) Only (ii) is correct (B) (i) and (ii) are correct (C) (iii) and (iv) are correct (D) Only (iv) is correct

Description : The main reinforcement in the toe of a T-shaped R C. retaining wall is provided on (i) Top face parallel to the wall (ii) Top face perpendicular to the wall (iii) Bottom face parallel to the wall (iv) ... (i) and (ii) are correct (C) (iii) and (iv) are correct (D) Only (iv) is correct

Last Answer : Answer: Option D

The main reinforcement in the heel of a T-shaped R.C. retaining wall is provided on (A) Top face perpendicular to wall (B) Bottom face perpendicular to wall (C) Both top and bottom faces perpendicular to wall (D) None of these

Description : The main reinforcement in the heel of a T-shaped R.C. retaining wall is provided on (A) Top face perpendicular to wall (B) Bottom face perpendicular to wall (C) Both top and bottom faces perpendicular to wall (D) None of these

Last Answer : Answer: Option A

In the design of a front counterfort in a counterfort retaining wall, the main reinforcement is provided on (i) Bottom face near counterfort (ii) Top face near counterfort (iii) Bottom face near centre of span (iv) Top face near centre of span The correct answer is (A) Only (i) (B) Only (ii) (C) Both (i) and (iv) (D) Both (ii) and (iii)

Description : In the design of a front counterfort in a counterfort retaining wall, the main reinforcement is provided on (i) Bottom face near counterfort (ii) Top face near counterfort (iii) Bottom face near centre of span (iv) Top ... ) (B) Only (ii) (C) Both (i) and (iv) (D) Both (ii) and (iii)

Last Answer : Answer: Option C

In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Description : In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Last Answer : (d) Depth of rib

Distribution reinforcement in a simply supported slab, is provided to distribute (A) Load (B) Temperature stress (C) Shrinkage stress (D) All the above

Description : Distribution reinforcement in a simply supported slab, is provided to distribute (A) Load (B) Temperature stress (C) Shrinkage stress (D) All the above

Last Answer : Answer: Option D

The temperature reinforcement in the vertical slab of a T-shaped R.C. retaining wall is (A) Not needed (B) Provided equally on inner and front faces (C) Provided more on inner face than on front face (D) Provided more on front face than on inner face

Description : The temperature reinforcement in the vertical slab of a T-shaped R.C. retaining wall is (A) Not needed (B) Provided equally on inner and front faces (C) Provided more on inner face than on front face (D) Provided more on front face than on inner face

Last Answer : Answer: Option D

In a limit state method of design, when shear reinforcement is not provided, the calculated shear stress at the critical section of a slab shall not exceed; [ A ] Ks 0.25 v fck [ B ] ks 0.20 v fck [ C ] ks 0.16 v fck [ D ] ks 0.10 v fck

Description : In a limit state method of design, when shear reinforcement is not provided, the calculated shear stress at the critical section of a slab shall not exceed; [ A ] Ks 0.25 v fck [ B ] ks 0.20 v fck [ C ] ks 0.16 v fck [ D ] ks 0.10 v fck

Last Answer : [ A ] Ks 0.25 v fck

In continuous beam between intermediate supports the deflection is a. convex down b. convex up c. concave up d. concave down

Description : In continuous beam between intermediate supports the deflection is a. convex down b. convex up c. concave up d. concave down

Last Answer : b. convex up

Which one of the following statements regarding septic tanks is wrong? A. A gap of 7.5 cm between the bottom of the covering slab and the top level of scum is provided B. The outlet invert level is kept 5 to 7.5 cm below the inlet invert level C. The minimum width of septic level is 90 cm D. The depth of tank is kept equal to its width

Description : Which one of the following statements regarding septic tanks is wrong? A. A gap of 7.5 cm between the bottom of the covering slab and the top level of scum is provided B. The outlet invert level is kept ... . The minimum width of septic level is 90 cm D. The depth of tank is kept equal to its width

Last Answer : ANS: D

An R.C.C. beam not provided with shear reinforcement may develop cracks in its bottom inclined roughly to the horizontal at (A) 25° (B) 35° (C) 45° (D) 55°

Description : An R.C.C. beam not provided with shear reinforcement may develop cracks in its bottom inclined roughly to the horizontal at (A) 25° (B) 35° (C) 45° (D) 55°

Last Answer : Answer: Option C

In a counterfort retaining wall, the main reinforcement is provided on the (i) Bottom face in front counterfort (ii) Inclined face in front counterfort (iii) Bottom face in back counterfort (iv) Inclined face in back counterfort The correct answer is (A) (i) and (ii), (B) (ii) and (iii) (C) (i) and (iv) (D) (iii) and (iv)

Description : In a counterfort retaining wall, the main reinforcement is provided on the (i) Bottom face in front counterfort (ii) Inclined face in front counterfort (iii) Bottom face in back counterfort (iv) Inclined face in back counterfort ... (B) (ii) and (iii) (C) (i) and (iv) (D) (iii) and (iv)

Last Answer : Answer: Option C

The thickness of base slab of a retaining wall generally provided, is (A) One half of the width of the stem at the bottom (B) One-third of the width of the stem at the bottom (C) One fourth of the width of the steam at the bottom (D) Width of the stem at the bottom

Description : The thickness of base slab of a retaining wall generally provided, is (A) One half of the width of the stem at the bottom (B) One-third of the width of the stem at the bottom (C) One fourth of the width of the steam at the bottom (D) Width of the stem at the bottom

Last Answer : Answer: Option D

The effective depth of a T-beam is the distance between the (a) Centre of the flange and the top of the tensile reinforcement (b) Top of the flange and the centre of the tensile reinforcement (c) Bottom of the flange and the centre of the tensile reinforcement (d) Centre of the flange and the bottom centre of the tensile reinforcement

Description : The effective depth of a T-beam is the distance between the (a) Centre of the flange and the top of the tensile reinforcement (b) Top of the flange and the centre of the tensile ... centre of the tensile reinforcement (d) Centre of the flange and the bottom centre of the tensile reinforcement

Last Answer : (b) Top of the flange and the centre of the tensile reinforcement

For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Description : For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Last Answer : Answer: Option D

In cement concrete pavements, tensile stress is due to: (A) Bending or deflection under wheel loads (B) Difference in temperature of the top and bottom of pavement (C) Contraction of slab during falling temperature (D) All the above

Description : In cement concrete pavements, tensile stress is due to: (A) Bending or deflection under wheel loads (B) Difference in temperature of the top and bottom of pavement (C) Contraction of slab during falling temperature (D) All the above

Last Answer : Answer: Option D

The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force

Description : The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force

Last Answer : Answer: Option B

If the diameter of the main reinforcement in a slab is 16 mm, the concrete cover to main bars is (A) 10 mm (B) 12 mm (C) 14 mm (D) 16 mm

Description : If the diameter of the main reinforcement in a slab is 16 mm, the concrete cover to main bars is (A) 10 mm (B) 12 mm (C) 14 mm (D) 16 mm

Last Answer : Answer: Option D

A part of the slab may be considered as the flange of the T-beam if (A) Flange has adequate reinforcement transverse to beam (B) It is built integrally with the beam (C) It is effectively bonded together with the beam (D) All the above

Description : A part of the slab may be considered as the flange of the T-beam if (A) Flange has adequate reinforcement transverse to beam (B) It is built integrally with the beam (C) It is effectively bonded together with the beam (D) All the above

Last Answer : Answer: Option D

In a slab, the pitch of the main reinforcement should not exceed its effective depth (A) Three times (B) Four times (C) Five times (D) Two times

Description : In a slab, the pitch of the main reinforcement should not exceed its effective depth (A) Three times (B) Four times (C) Five times (D) Two times

Last Answer : Answer: Option A

Reinforcement in cement concrete slab of road pavements, is placed (A) Longitudinally (B) Transversely (C) Longitudinally and transversely (D) In the form of welded wire mesh

Description : Reinforcement in cement concrete slab of road pavements, is placed (A) Longitudinally (B) Transversely (C) Longitudinally and transversely (D) In the form of welded wire mesh

Last Answer : Answer: Option D

When shear stress exceeds the permissible limit in a slab, then it is reduced by (A) Increasing the depth (B) Providing shear reinforcement (C) Using high strength steel (D) Using thinner bars but more in number

Description : When shear stress exceeds the permissible limit in a slab, then it is reduced by (A) Increasing the depth (B) Providing shear reinforcement (C) Using high strength steel (D) Using thinner bars but more in number

Last Answer : Answer: Option A

A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter

Description : A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter

Last Answer : (b) 8 mm diameter

The main reinforcement of a R.C. slab consists of 10 mm bars at 100 mm spacing; if it is desired to replace the 10 mm bars by 12 mm bars, then the spacing of 12mm bars should be (a) 120 mm (b) 140 mm (c ) 144 mm (d) 160mm

Description : The main reinforcement of a R.C. slab consists of 10 mm bars at 100 mm spacing; if it is desired to replace the 10 mm bars by 12 mm bars, then the spacing of 12mm bars should be (a) 120 mm (b) 140 mm (c ) 144 mm (d) 160mm

Last Answer : (c ) 144 mm

The amount of reinforcement for main bars in a slab, is based upon (a) Maximum bending moment (b) Minimum bending moment (c) Maximum shear force (d) Minimum shear force

Description : The amount of reinforcement for main bars in a slab, is based upon (a) Maximum bending moment (b) Minimum bending moment (c) Maximum shear force (d) Minimum shear force

Last Answer : (a) Maximum bending moment

in a simply supported slab, the pitch of distribution reinforcement should not be more than_____________the effective depth of slab or 60cm which ever is smaller. (a) Double (b) Three times (c) Five times (d) Six times

Description : in a simply supported slab, the pitch of distribution reinforcement should not be more than_____________the effective depth of slab or 60cm which ever is smaller. (a) Double (b) Three times (c) Five times (d) Six times

Last Answer : (c) Five times

The pitch of bars of main reinforcement in slab should not exceed ________the effective depth of slab. (a) Double (b) Three times (c) Five times (d) Six times

Description : The pitch of bars of main reinforcement in slab should not exceed ________the effective depth of slab. (a) Double (b) Three times (c) Five times (d) Six times

Last Answer : (b) Three times

The purpose of transverse reinforcement, in a slab is to (a) Distribute the effect to f point load on the slab more evenly and uniformly (b) Distribute the shrinkage and temp cracks more ever (c) Keep the main reinforcement in position (d) All of the above.

Description : The purpose of transverse reinforcement, in a slab is to (a) Distribute the effect to f point load on the slab more evenly and uniformly (b) Distribute the shrinkage and temp cracks more ever (c) Keep the main reinforcement in position (d) All of the above.

Last Answer : (d) All of the above.

The size of the mesh at each corner meant for torsion reinforcement in a rectangular slab of size (Lx ´ Ly) is Lx = shorter span Lx = Longer span [ A ] 0.1 Ly x 1 Ly [ B ] 0.2 Ly x 0.2 Ly [ C ] 0.1 Lx x 0.1 Lx [ D ] 0.2 Lx x 0.2 Lx

Description : The size of the mesh at each corner meant for torsion reinforcement in a rectangular slab of size (Lx ´ Ly) is Lx = shorter span Lx = Longer span [ A ] 0.1 Ly x 1 Ly [ B ] 0.2 Ly x 0.2 Ly [ C ] 0.1 Lx x 0.1 Lx [ D ] 0.2 Lx x 0.2 Lx

Last Answer : [ D ] 0.2 Lx x 0.2 Lx

The slab is said to be orthotropically reinforced , when the reinforcement is arranged in; [ A ] Single direction [ B ] Two directions at right angles with equal meshes [ C ] Two directions at right angles with unequal meshes [ D ] At the corners only

Description : The slab is said to be orthotropically reinforced , when the reinforcement is arranged in; [ A ] Single direction [ B ] Two directions at right angles with equal meshes [ C ] Two directions at right angles with unequal meshes [ D ] At the corners only

Last Answer : [ C ] Two directions at right angles with unequal meshes

The Minimum amount of steel for Main reinforcement in slab should be (Fe 415- grade of steel) [ A ] 0.12 percent of gross cross sectional area [ B ] 0.15 percent of gross cross sectional area [ C ] 0.20 percent of gross cross sectional area [ D ] 0.25 percent of gross cross sectional area.

Description : The Minimum amount of steel for Main reinforcement in slab should be (Fe 415- grade of steel) [ A ] 0.12 percent of gross cross sectional area [ B ] 0.15 percent of gross cross sectional area [ C ] 0.20 percent of gross cross sectional area [ D ] 0.25 percent of gross cross sectional area.

Last Answer : [ A ] 0.12 percent of gross cross sectional area

Which of the following is not a characteristic feature of yield lines? [ A ] Yield lines end at a slab boundary [ B ] Yield lines are of parabolical shape [ C ] Axes of rotation generally lie along the lines of supports [ D ] None of the above.

Description : Which of the following is not a characteristic feature of yield lines? [ A ] Yield lines end at a slab boundary [ B ] Yield lines are of parabolical shape [ C ] Axes of rotation generally lie along the lines of supports [ D ] None of the above.

Last Answer : [ B ] Yield lines are of parabolical shape

The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6

Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6

Last Answer : Answer: Option C

The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6

Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6

Last Answer : (c) 0.9

In case the factor of safety against sliding is less than 1.5, a portion of slab is constructed downwards at the end of the heel slab, which is known as (A) A key (B) A cut-off wall (C) A rib (D) All the above

Description : In case the factor of safety against sliding is less than 1.5, a portion of slab is constructed downwards at the end of the heel slab, which is known as (A) A key (B) A cut-off wall (C) A rib (D) All the above

Last Answer : Answer: Option D

In a T-beam , the breadth of the rib is equal to the (a) Total thickness of the slab, including cover (b) Width of the portion of the beam in the compression zone (c) Width of the portion of the beam in the compression zone (d) All the above.

Description : In a T-beam , the breadth of the rib is equal to the (a) Total thickness of the slab, including cover (b) Width of the portion of the beam in the compression zone (c) Width of the portion of the beam in the compression zone (d) All the above.

Last Answer : (c) Width of the portion of the beam in the compression zone

The portion of the slab which acts monolithically with the beam and which resists the compressive stresses, is called _________of flange of the T-beam (a) Length (b) Breadth (c) Thickness (d) Depth

Description : The portion of the slab which acts monolithically with the beam and which resists the compressive stresses, is called _________of flange of the T-beam (a) Length (b) Breadth (c) Thickness (d) Depth

Last Answer : (b) Breadth

Pick up the correct statement from the following: (A) Construction joints in columns are provided a few cm below the junction of beam (B) Construction joints in columns are provided at the bottom hunching (C) Construction joints in beams and slabs are provided within middle third (D) All the above

Description : Pick up the correct statement from the following: (A) Construction joints in columns are provided a few cm below the junction of beam (B) Construction joints in columns are provided at the bottom ... (C) Construction joints in beams and slabs are provided within middle third (D) All the above

Last Answer : Answer: Option D

For a continuous slab of 3 m × 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (A) 50 mm (B) 75 mm (C) 100 mm (D) 120 mm

Description : For a continuous slab of 3 m × 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (A) 50 mm (B) 75 mm (C) 100 mm (D) 120 mm

Last Answer : (B) 75 mm

In counterfort type retaining walls (i) The vertical slab is designed as a continuous slab (ii) The heel slab is designed as a continuous slab (iii) The vertical slab is designed as a cantilever (iv) The heel slab is designed as a cantilever The correct answer is (A) (i) and (ii) (B) (i)and(iv) (C) (ii) and (iii) (D) (iii) and (iv)

Description : In counterfort type retaining walls (i) The vertical slab is designed as a continuous slab (ii) The heel slab is designed as a continuous slab (iii) The vertical slab is designed as a cantilever (iv) The heel slab is designed ... (ii) (B) (i)and(iv) (C) (ii) and (iii) (D) (iii) and (iv)

Last Answer : Answer: Option A

For a continuous slab of 3 m x 35 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (a) 120 mm (b) 100 mm (c) 75 mm (d) 50 mm

Description : For a continuous slab of 3 m x 35 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (a) 120 mm (b) 100 mm (c) 75 mm (d) 50 mm

Last Answer : (a) 120 mm

A two way slab (a) May be simply supported on the four edges, with comers not held down and carrying uniformly distributed load. (b) May be simply supported on the four edge , with corners held down and carrying uniformly distributed load. (c) May have edges fixed or continuous and carrying uniformly distributed load. (d) All the above.

Description : A two way slab (a) May be simply supported on the four edges, with comers not held down and carrying uniformly distributed load. (b) May be simply supported on the four edge , with corners held ... . (c) May have edges fixed or continuous and carrying uniformly distributed load. (d) All the above.

Last Answer : (d) All the above.

According to IS: 456-2000, the span/overall depth ratio for a continuous two-way slab in order to control deflection is given by [ A ] 20 [ B ] 28 [ C ] 32 [ D ] 40

Description : According to IS: 456-2000, the span/overall depth ratio for a continuous two-way slab in order to control deflection is given by [ A ] 20 [ B ] 28 [ C ] 32 [ D ] 40

Last Answer : [ C ] 32

The basic value of span to depth ratio for one way continuous slab is [ A ] 20 [ B ] 26 [ C ] 35 [ D ] 40

Description : The basic value of span to depth ratio for one way continuous slab is [ A ] 20 [ B ] 26 [ C ] 35 [ D ] 40

Last Answer : [ B ] 26

A bottle of sodalime is grasped by the neck and swung briskly in a vertical circle, Near which portion of the bottle do the bubbles collect? (1) Near the bottom (2) In the middle of the bottom (3) Near the neck (4) Bubbles remain distributed uniformly

Description : A bottle of sodalime is grasped by the neck and swung briskly in a vertical circle, Near which portion of the bottle do the bubbles collect? (1) Near the bottom (2) In the middle of the bottom (3) Near the neck (4) Bubbles remain distributed uniformly

Last Answer : (3) Near the neck Explanation: When the bottle of soda water is grasped by the neck and swung briskly in a vertical circle, the bubbles collect at the top of the bottle which is ... beverage forms form bubbles when the dissolved carbon dioxide is depressurized to form emulsions at the top.