To ensure that the hogging bending moment at two points of suspension of a pile of length L equals the sagging moment at its centre, the distances of the points of suspension from either end, is (A) 0.107 L (B) 0.207 L (C) 0.307 L (D) 0.407 L

To ensure that the hogging bending moment at two points of suspension of a pile of
length L equals the sagging moment at its centre, the distances of the points of suspension from
either end, is
(A) 0.107 L
(B) 0.207 L
(C) 0.307 L
(D) 0.407 L
by

1 Answer

Answer :

Answer: Option B
by

Related questions

A beam of length L supported on two intermediate rollers carries a uniformly distributed load on its entire length. If sagging B.M. and hogging B.M. of the beam are equal, the length of each overhang, is (A) 0.107 L (B) 0.207 L (C) 0.307 L(D) 0.407 L

Description : A beam of length L supported on two intermediate rollers carries a uniformly distributed load on its entire length. If sagging B.M. and hogging B.M. of the beam are equal, the length of each overhang, is (A) 0.107 L (B) 0.207 L (C) 0.307 L(D) 0.407 L

Last Answer : (B) 0.207 L

A pile of length carrying a uniformly distributed load per metre length is suspended at the centre and from other two points 0.15 L from either end ; the maximum hogging moment will be (A) WL²/15 (B) WL²/30 (C) WL²/60 (D) WL²/90

Description : A pile of length carrying a uniformly distributed load per metre length is suspended at the centre and from other two points 0.15 L from either end ; the maximum hogging moment will be (A) WL²/15 (B) WL²/30 (C) WL²/60 (D) WL²/90

Last Answer : Answer: Option D

A simply supported beam which carries a uniformly distributed load has two equal overhangs. To have maximum B.M. produced in the beam least possible, the ratio of the length of the overhang to the total length of the beam, is (A) 0.207 (B) 0.307 (C) 0.407 (D) 0.508

Description : A simply supported beam which carries a uniformly distributed load has two equal overhangs. To  have maximum B.M. produced in the beam least possible, the ratio of the length of the overhang  to the total length of the beam, is  (A) 0.207  (B) 0.307  (C) 0.407  (D) 0.508 

Last Answer : (A) 0.207 

In a pile of length , the points of suspension from ends for lifting it are located at (A) 0.207 l (B) 0.25 l (C) 0.293 l (D) 0.333

Description : In a pile of length , the points of suspension from ends for lifting it are located at (A) 0.207 l (B) 0.25 l (C) 0.293 l (D) 0.333 l

Last Answer : A

The concavity produced on the beam section about the centre line when downward force acts on it is called as (a) Hogging or positive bending moment (b) Hogging or negative bending moment (c) Sagging or positive bending moment (d) Sagging or negative bending moment

Description : The concavity produced on the beam section about the centre line when downward force acts on it is called as (a) Hogging or positive bending moment (b) Hogging or negative bending moment (c) Sagging or positive bending moment (d) Sagging or negative bending moment

Last Answer : (b) Hogging or negative bending moment

Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to resist a sagging bending moment near mid-span. (c) When the slab is built into a brick or masonry wall the slab should be designed to resist a hogging moment at the face of the support. (d) All of the above.

Description : Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to ... be designed to resist a hogging moment at the face of the support. (d) All of the above.

Last Answer : (d) All of the above.

During erection, the pile of length is supported by a crane at a distance of (A) 0.207 l (B) 0.293 l (C) 0.707 l (D) 0.793 l

Description : During erection, the pile of length is supported by a crane at a distance of (A) 0.207 l (B) 0.293 l (C) 0.707 l (D) 0.793 l

Last Answer : (C) 0.707 l

A pile of length carrying a uniformly distributed load per metre length is suspended at two points, the maximum, B.M. at the centre of the pile or at the points of suspension, is (A) WL/8 (B) WL²/24 (C) WL²/47 (D) WL²/16

Description : A pile of length carrying a uniformly distributed load per metre length is suspended at two points, the maximum, B.M. at the centre of the pile or at the points of suspension, is (A) WL/8 (B) WL²/24 (C) WL²/47 (D) WL²/16

Last Answer : Answer: Option C

A simply supported beam carries two equal concentrated loads W at distances L/3 from either support. The maximum bending moment (A) WL/3 (B) WL/4 (C) 5WL/4 (D) 3WL/12

Description : A simply supported beam carries two equal concentrated loads W at distances L/3 from either support. The maximum bending moment (A) WL/3 (B) WL/4 (C) 5WL/4 (D) 3WL/12

Last Answer : (A) WL/3

When a slab is continuous over several spans, negative (i.e. hogging ) bending moment is induced over the (a) End supports (b) Intermediate supports (c) Both (a) & (b) (d) Non of the

Description : When a slab is continuous over several spans, negative (i.e. hogging ) bending moment is induced over the (a) End supports (b) Intermediate supports (c) Both (a) & (b) (d) Non of the

Last Answer : (b) Intermediate supports

In a combined footing for two columns carrying unequal loads, the maximum hogging bending moment occurs at (A) Less loaded column (B) More loaded column (C) A point of the maximum shear force (D) A point of zero shear force

Description : In a combined footing for two columns carrying unequal loads, the maximum hogging bending moment occurs at (A) Less loaded column (B) More loaded column (C) A point of the maximum shear force (D) A point of zero shear force

Last Answer : Answer: Option D

A beam of length L is pinned at both ends and is subjected to a concentrated bending couple of moment M at its centre. The maximum bending moment in the beam is (A) M (B) M/2 (C) M/3 (D) ML/2

Description : A beam of length L is pinned at both ends and is subjected to a concentrated bending couple of  moment M at its centre. The maximum bending moment in the beam is  (A) M (B) M/2  (C) M/3  (D) ML/2 

Last Answer : (A) M

If the length of a wall on either side of a lintel opening is at least half of its effective span L, the load W carried by the lintel is equivalent to the weight of brickwork contained in an equilateral triangle, producing a maximum bending moment (A) WL/2 (B) WL/4 (C) WL/6 (D) WL/8

Description : If the length of a wall on either side of a lintel opening is at least half of its effective span L, the load W carried by the lintel is equivalent to the weight of brickwork contained in an equilateral triangle, producing a maximum bending moment (A) WL/2 (B) WL/4 (C) WL/6 (D) WL/8

Last Answer : Answer: Option C

In IPv4, what is the value of the total length field in bytes if the header is 28 bytes and the data field is 400bytes? A) 428 B) 407 C) 107 D) 427

Description : In IPv4, what is the value of the total length field in bytes if the header is 28 bytes and the data field is 400bytes? A) 428 B) 407 C) 107 D) 427

Last Answer : 428

Under sagging bending moment, the uppermost fiber of the beam is in (a) Shear (b) Compression (c) Tension (d) None)

Description : Under sagging bending moment, the uppermost fiber of the beam is in (a) Shear (b) Compression (c) Tension (d) None)

Last Answer : (b) Compression

In case of cantilever, irrespective of the type of loading the maximum bendry moment and maximum shear force occur at a.107 dynes b.Free end c.2/3 of the length, from the free end d.Centre of the beam e.Fixed end

Description : In case of cantilever, irrespective of the type of loading the maximum bendry moment and maximum shear force occur at a.107 dynes b.Free end c.2/3 of the length, from the free end d.Centre of the beam e.Fixed end

Last Answer : e. Fixed end

If f1 and f2 are the distances from the optical centre of a convex lens of focal length to conjugate two points P1 and P2 respectively, the following relationship holds good (A) f = f1 + f2 (B) f = ½ (f1 + f2) (C) 1/f = 1/f1 + 1/f2 (D) None of these

Description : If f1 and f2 are the distances from the optical centre of a convex lens of focal length to conjugate two points P1 and P2 respectively, the following relationship holds good (A) f = f1 + f2 (B) f = ½ (f1 + f2) (C) 1/f = 1/f1 + 1/f2 (D) None of these

Last Answer : (C) 1/f = 1/f1 + 1/f2

In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is (a) Wl at the free end (b) Wl at the fixed end (c) Wl/2 at the fixed end (d) Wl at the free end

Description : In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is (a) Wl at the free end (b) Wl at the fixed end (c) Wl/2 at the fixed end (d) Wl at the free end

Last Answer : (b) Wl at the fixed end

In a simply supported beam subjected to uniformly distributed load (w) over the entire length (l), total load=W, maximum Bending moment is (a) Wl/8 or wl2/8 at the mid-point (b) Wl/8 or wl2/8 at the end (c) Wl/4 or wl2/4 (d) Wl/2

Description : In a simply supported beam subjected to uniformly distributed load (w) over the entire length (l), total load=W, maximum Bending moment is (a) Wl/8 or wl2/8 at the mid-point (b) Wl/8 or wl2/8 at the end (c) Wl/4 or wl2/4 (d) Wl/2

Last Answer : (a) Wl/8 or wl2/8 at the mid-point

For a simply supported beam carrying uniformly distributed load W on it entire length L, the maximum bending moment is (A) WL/4 (B) WL/8 (C) WL/2 (D) WL/3

Description : For a simply supported beam carrying uniformly distributed load W on it entire length L, the maximum bending moment is (A) WL/4 (B) WL/8 (C) WL/2 (D) WL/3

Last Answer : (B) WL/8

The function of king post in a king post roof truss is (A) To support the frame work of the roof (B) To receive the ends of principal rafter (C) To prevent the walls from spreading outward (D) To prevent the tie beam from sagging at its centre

Description : The function of king post in a king post roof truss is (A) To support the frame work of the roof (B) To receive the ends of principal rafter (C) To prevent the walls from spreading outward (D) To prevent the tie beam from sagging at its centre

Last Answer : Answer: Option D

A cantilever of length is subjected to a bending moment at its free end. If EI is the flexural rigidity of the section, the deflection of the free end, is (A) ML/EI (B) ML/2EI (C) ML²/2EI (D) ML²/3EI

Description : A cantilever of length is subjected to a bending moment at its free end. If EI is the flexural  rigidity of the section, the deflection of the free end, is  (A) ML/EI (B) ML/2EI (C) ML²/2EI (D) ML²/3EI

Last Answer : (D) ML²/3EI

A cantilever carrying a uniformly distributed load W over its full length is propped at its free end such that it is at the level of the fixed end. The bending moment will be zero at its free end also at (A) Midpoint of the cantilever (B) Fixed point of the cantilever (C) 1/4th length from free end (D) 3/4th length from free end

Description : A cantilever carrying a uniformly distributed load W over its full length is propped at its free end such that it is at the level of the fixed end. The bending moment will be zero at its free end also at ... point of the cantilever (C) 1/4th length from free end (D) 3/4th length from free end

Last Answer : (D) 3/4th length from free end

When the bending moment is parabolic curve between two points, it indicates that there is (a) No loading between the two points (b) Point loads between the two points (c) U.D.L. between the two points (d) Uniformly varying load between the two points

Description : When the bending moment is parabolic curve between two points, it indicates that there is (a) No loading between the two points (b) Point loads between the two points (c) U.D.L. between the two points (d) Uniformly varying load between the two points

Last Answer : (c) U.D.L. between the two points

If the positive and negative shear force diagram areas are not equal, it can be concluded that a.shear force diagram has been wrongly drawn b.there is at least one couple acting on the beam c.107 dynes d.there are at least two maxima for bending moment e.bending moment does not change sign

Description : If the positive and negative shear force diagram areas are not equal, it can be concluded that a.shear force diagram has been wrongly drawn b.there is at least one couple acting on the beam c.107 dynes d.there are at least two maxima for bending moment e.bending moment does not change sign

Last Answer : b. there is at least one couple acting on the beam

A beam fixed at both ends with a central load W in the middle will have zero bending moment at a.one place b.two places c.no where d.three places e.107 dynes

Description : A beam fixed at both ends with a central load W in the middle will have zero bending moment at a.one place b.two places c.no where d.three places e.107 dynes

Last Answer : b. two places

When a series of wheel loads crosses a simply supported girder, the maximum bending moment under any given wheel load occurs when (A) The centre of gravity of the load system is midway between the centre of span and wheel load under consideration (B) The centre of span is midway between the centre of gravity of the load system and the wheel load under consideration (C) The wheel load under consideration is midway between the centre of span and the centre of gravity of the load system (D) None of the above

Description : When a series of wheel loads crosses a simply supported girder, the maximum bending moment under any given wheel load occurs when (A) The centre of gravity of the load system is midway between the centre of ... the centre of span and the centre of gravity of the load system (D) None of the above

Last Answer : (B) The centre of span is midway between the centre of gravity of the load system and the wheel load under consideration

The maximum bending moment due to a train of wheel loads on a simply supported girder (A) Always occurs at centre of span (B) Always occurs under a wheel load (C) Never occurs under a wheel load (D) None of the above

Description : The maximum bending moment due to a train of wheel loads on a simply supported girder (A) Always occurs at centre of span (B) Always occurs under a wheel load (C) Never occurs under a wheel load (D) None of the above

Last Answer : (B) Always occurs under a wheel load

For a simply supported beam with a central load, the bending moment is (A) Least at the centre (B) Least at the supports (C) Maximum at the supports (D) Maximum at the centre

Description : For a simply supported beam with a central load, the bending moment is  (A) Least at the centre  (B) Least at the supports  (C) Maximum at the supports  (D) Maximum at the centre

Last Answer : (D) Maximum at the centre

To ensure constant moisture content in aggregates (A) Area of each aggregate pile should be large (B) Height of each aggregate pile should not exceed 1.50 m (C) Aggregate pile should be left for 24 hours before aggregates are used (D) All the above

Description : To ensure constant moisture content in aggregates (A) Area of each aggregate pile should be large (B) Height of each aggregate pile should not exceed 1.50 m (C) Aggregate pile should be left for 24 hours before aggregates are used (D) All the above

Last Answer : Answer: Option D

A simply supported beam of span L carries a concentrated load W at its mid-span. The maximum bending moment M is (A) WL/2 (B) WL/4 (C) WL/8 (D) WL/12

Description : A simply supported beam of span L carries a concentrated load W at its mid-span. The maximum  bending moment M is  (A) WL/2  (B) WL/4  (C) WL/8  (D) WL/12

Last Answer : (B) WL/4

A bending moment may be defined as: (A) Arithmetic sum of the moments of all the forces on either side of the section (B) Arithmetic sum of the forces on either side of the section (C) Algebraic sum of the moments of all the forces on either side of the section (D) None of these

Description : A bending moment may be defined as: (A) Arithmetic sum of the moments of all the forces on either side of the section (B) Arithmetic sum of the forces on either side of the section (C) Algebraic sum of the moments of all the forces on either side of the section (D) None of these

Last Answer : (C) Algebraic sum of the moments of all the forces on either side of the section

A doubly reinforced section is used (a) When the members are subjected to alternate external loads and the bending moment in the sections reverses. (b) When the member are subjected to loading eccentric in either side of the axis. (c) When the members are subjected to accidental lateral loads . (d) All of the above

Description : A doubly reinforced section is used (a) When the members are subjected to alternate external loads and the bending moment in the sections reverses. (b) When the member are subjected to loading eccentric in ... . (c) When the members are subjected to accidental lateral loads . (d) All of the above

Last Answer : (d) All of the above

If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than (A) WL/12 (L - 2D/3)² (B) WL/10 (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Description : If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span ... (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Last Answer : Answer: Option C

For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Description : For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Last Answer : Answer: Option D

The purlins in roof trusses are placed at the panel points essentially to avoid (a) Axial force in rafter (b) Shear force in rafter (c ) Deflection in rafter (d) Bending moment in rafter

Description : The purlins in roof trusses are placed at the panel points essentially to avoid (a) Axial force in rafter (b) Shear force in rafter (c ) Deflection in rafter (d) Bending moment in rafter

Last Answer : (d) Bending moment in rafter

The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T

Description : The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T

Last Answer : (A) T/2

If a constant section beam is subjected to a uniform bending moment throughout, its length bends to (A) A circular arc (B) A parabolic arc (C) A catenary (D) None of these

Description : If a constant section beam is subjected to a uniform bending moment throughout, its length bends  to  (A) A circular arc  (B) A parabolic arc  (C) A catenary  (D) None of these 

Last Answer : (A) A circular arc 

In case of a beam subjected to pure bending a.107 dynes b.the stress intensity in any fibre is proportional to the distance of the fibre from the neutral axis c.the stress intensity in any fibre is proportional to the distance of the fibre from the load carrying end d.the stress intensity in any fibre is uniform e.the nature of stress in any fibre is identical

Description : In case of a beam subjected to pure bending a.107 dynes b.the stress intensity in any fibre is proportional to the distance of the fibre from the neutral axis c.the stress intensity in any fibre is ... d.the stress intensity in any fibre is uniform e.the nature of stress in any fibre is identical

Last Answer : b. the stress intensity in any fibre is proportional to the distance of the fibre from the neutral axis

A uniformly distributed load (w) of length shorter than the span crosses a girder. The bending moment at a section in the girder will be maximum when (a) Head of the load is at the section (b) Tail of the load is at the section (c) Section divides the load in the same ratio as it divides the span (d) Section divides the load in two equal lengths.

Description : A uniformly distributed load (w) of length shorter than the span crosses a girder. The bending moment at a section in the girder will be maximum when (a) Head of the load is at the section (b) Tail ... load in the same ratio as it divides the span (d) Section divides the load in two equal lengths.

Last Answer : (c) Section divides the load in the same ratio as it divides the span

If is the difference in height between end points of a chain of length , the required slope correction is (A) h²/2l (B) h/2l (C) h²/l (D) 2h²/2l

Description : If is the difference in height between end points of a chain of length , the required slope correction is (A) h²/2l (B) h/2l (C) h²/l (D) 2h²/2l

Last Answer : (A) h²/2l

The maximum bending moment for a simply supported beam with a uniformly distributed load w/unit length, is (A) WI/2 (B) WI²/4 (C) WI²/8 (D) WI²/12

Description : The maximum bending moment for a simply supported beam with a uniformly distributed  load w/unit length, is  (A) WI/2  (B) WI²/4  (C) WI²/8  (D) WI²/12

Last Answer : (C) WI²/8 

The shape of the bending moment diagram over the length of a beam, having no external load, is always (A) Linear (B) Parabolic (C) Cubical (D) Circular

Description : The shape of the bending moment diagram over the length of a beam, having no external load, is always (A) Linear (B) Parabolic (C) Cubical (D) Circular

Last Answer : (A) Linear

The shape of the bending moment diagram over the length of a beam, carrying a uniformly distributed load is always (A) Linear (B) Parabolic (C) Cubical (D) Circular

Description : The shape of the bending moment diagram over the length of a beam, carrying a uniformly  distributed load is always  (A) Linear  (B) Parabolic  (C) Cubical  (D) Circular

Last Answer : (B) Parabolic 

The shape of the bending moment diagram over the length of a beam, carrying a uniformly increasing load, is always (A) Linear (B) Parabolic (C) Cubical (D) Circular

Description : The shape of the bending moment diagram over the length of a beam, carrying a uniformly  increasing load, is always  (A) Linear  (B) Parabolic  (C) Cubical  (D) Circular 

Last Answer : (C) Cubical 

In a slider crank mechanism, the crank is rotating at 200 rpm. If length of connecting rod is 8 mts and crank shaft is 2 mts, velocity of crosshead at 30? rotation of crank shaft equals. a.30.2 m/s b.33.2 m/s c.35.8 mts/s d.107 dynes e.25.5 m/s

Description : In a slider crank mechanism, the crank is rotating at 200 rpm. If length of connecting rod is 8 mts and crank shaft is 2 mts, velocity of crosshead at 30? rotation of crank shaft equals. a.30.2 m/s b.33.2 m/s c.35.8 mts/s d.107 dynes e.25.5 m/s

Last Answer : e. 25.5 m/s

Maximum deflection of a cantilever due to pure bending moment M at its free end, is (A) ML²/3EI (B) ML²/4EI (C) ML²/6EI (D) ML²/2EI

Description : Maximum deflection of a cantilever due to pure bending moment M at its free end, is (A) ML²/3EI (B) ML²/4EI (C) ML²/6EI (D) ML²/2EI

Last Answer : (D) ML²/2EI

The moment diagram for a cantilever whose free end is subjected to a bending moment, will be a (A) Triangle (B) Rectangle (C) Parabola (D) Cubic parabola

Description : The moment diagram for a cantilever whose free end is subjected to a bending moment, will be a  (A) Triangle  (B) Rectangle  (C) Parabola  (D) Cubic parabola 

Last Answer : (B) Rectangle