Description : In a combined footing if shear stress does not exceed 5 kg/cm2 , the nominal stirrups provided are (A) 6 legged (B) 8 legged (C) 10 legged (D) 12 legged
Last Answer : Answer: Option B
Description : In a combined footing if shear stress exceeds 5 kg/cm2 , the nominal stirrups provided are: (A) 6 legged (B) 8 legged (C) 10 legged (D) 12 legged
Last Answer : Answer: Option D
Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm (C) 150 cm (D) 200 cm
Last Answer : Answer: Option C
Description : An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section
Description : If the shear stress in a R.C.C. beam is (A) Equal or less than 5 kg/cm2 , no shear reinforcement is provided (B) Greater than 4 kg/cm2 , but less than 20 kg/cm2 , shear reinforcement is provided (C) Greater than 20 kg/cm2 , the size of the section is changed (D) All the above
Description : In the zone of R.C.C. beam where shear stress is less than 5 kg/cm2 , nominal reinforcement is provided at a pitch of (A) One-half lever arm of the section (B) One-third lever arm of the section (C) Lever arm of the section (D) One and half lever arm of the section
Description : The principal stresses at a point are 100, 100 and -200 kgf/cm2 , the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm2
Last Answer : (A) 100 kg/cm2
Description : In a combined footing for two columns carrying unequal loads, the maximum hogging bending moment occurs at (A) Less loaded column (B) More loaded column (C) A point of the maximum shear force (D) A point of zero shear force
Description : The allowable tensile stress in mild steel stirrups, reinforced cement concrete, is (A) 1400 kg/cm2 (B) 190 kg/cm2 (C) 260 kg/cm2 (D) 230 kg/cm
Last Answer : Answer: Option A
Description : Based on punching shear consideration, the overall depth of a combined footing under a column A, is (A) (Area of the column A Safe punching stress)/Load on column A (B) (Perimeter of column A ... punching stress)/(Load on column A Upward pressure Area of the column) (D) None of these
Description : If L is the effective span of a R.C.C. beam which is subjected to maximum shear qmax at the ends, the distance from either end over which stirrups for the shear, are provided, is (A) (L/2) (1 - 3/qmax) (B) (L/3) (1 - 5/qmax) (C) (L/2) (1 - 5/qmax) (D) (L/2) (1 - 2/qmax)
Description : An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is ( ... shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined members (D) Needs revision of the section
Description : According to IS : 456-2000, clause 39.4, stirrups should be provided for a shear of [ A ] at least 75% [ B ] at least 50% [ C ] at least 25 % [ D ] none of the above.
Last Answer : [ B ] at least 50%
Description : The foundation in which a cantilever beam is provided to join two footings, is known as (A) Strip footing (B) Strap footing (C) Combined footing (D) Raft footing
Description : Pick up the correct statement from the following: (A) A combined footing is so proportioned that centre of gravity of supporting area coincides with centre of gravity of two column loads (B) A ... in shape (C) Trapezoidal shaped footings may be provided under any loading (D) All the above
Description : For the construction of flyovers in sandy soils, the type of foundation provided, is (A) Strap footing (B) Raft footing (C) Combined footing (D) Pier footing
Description : A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one- ... beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45
Description : To support a heavy structure in sandy soil, the type of foundation generally used, is (A) Combined footing (B) Raft footing (C) Pier footing (D) Strap footing
Description : The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm
Description : If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm
Description : A short column 20 cm 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on ... should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these
Description : If the permissible compressive and tensile stresses in a singly reinforced beam are 50 kg/cm2 and 1400 kg/cm2 respectively and the modular ratio is 18, the percentage area At of the steel required for an economic section, is (A) 0.496 % (B) 0.596 % (C) 0.696 % (D) 0.796 %
Description : An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity ... , is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2
Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m
Description : In soils possessing low bearing capacity, the type of foundation generally provided, is (A) Column footing (B) Grillage footing (C) Raft footing (D) All the above
Last Answer : Option D
Description : Terzaghi's analysis assumes: (A) Soil is homogeneous and isotropic (B) Elastic zone has straight boundaries inclined at = to the horizontal and plastic zones fully developed (C) Failure zones do not extend above the horizontal plane through the base of the footing (D) All the above
Description : Dimensions of a beam need be changed if the shear stress is more than (A) 10 kg/cm2 (B) 15 kg/cm2 (C) 20 kg/cm2 (D) 25 kg/cm
Description : The reinforced concrete beam which has width 25 cm, lever arm 40 cm, shear force 6t/cm2 , safe shear stress 5 kg/cm2 and B.M. 24 mt, (A) Is safe in shear (B) Is unsafe in shear (C) Is over safe in shear (D) Needs redesigning
Description : In a tension test, the yield stress is 300 kg/cm2 , in the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm (D) 250 kg/cm2
Description : If the bearing capacity of soil is 10 tonnes/cm2 and the projection of plain concrete footing from walls, is a cm, the depth D of footing is (A) D = 0.0775 a (B) D = 0.775 a (C) D = 0.775 a (D) D = 0.775 a2
Description : Passing zones are generally not provided on (A) Summit curves (B) Horizontal curves (C) Two lane highways (D) All the above
Description : Maximum allowable spacing of shear reinforcement for inclined stirrups with an inclination of 45° is restricted to [ A ] 0.75 d [ B ] 0.45 d [ C ] 0.90 d [ D ] d
Last Answer : [ D ] d
Description : Maximum allowable spacing of shear reinforcement for vertical stirrups is restricted to [ A ] d [ B ] 0.45 d [ C ] 0.75 d [ D ] 0.90 d
Last Answer : [ C ] 0.75 d
Description : According to IS: 456-2000 spacing of vertical stirrups for shear reinforcement has been limited to [ A ] 0.75 d [ B ] 450 mm [ C ] lesser of 0.75 d or 300 mm [ D ] lesser of 0.75d or 450 mm
Last Answer : [ C ] lesser of 0.75 d or 300 mm
Description : If the length of a combined footing for two columns l metres apart is L and the projection on the left side of the exterior column is x, then the projection y on the right side of the exterior column, in order to have a uniformly distributed ... l - ) (C) y = L/2 - (l + ) (D) y = L/2 - (l - )
Description : Top bars are extended to the projecting parts of the combined footing of two columns Ldistance apart for a distance of (A) 0.1 L from the outer edge of column (B) 0.1 L from the centre edge of column (C) Half the distance of projection (D) One-fourth the distance of projection
Description : A 8 metre long simply supported rectangular beam which carries a distributed load 45 kg/m. experiences a maximum fibre stress 160 kg/cm2 . If the moment of inertia of the beam is 640 cm4 , the overall depth of the beam is (A) 10 cm (B) 12 cm (C) 15 cm (D) 18 cm
Last Answer : (A) 10 cm
Description : The bearing capacity of granite is generally (A) 5 to 10 kg/cm2 (B) 15 to 20 kg/cm2 (C) 30 to 35 kg/cm2 (D) 40 to 45 kg/cm2
Description : Pick up the incorrect statement from the following: (A) In dog-legged stairs, no space between its flights is provided (B) In open newel stair, a rectangular well is provided (C) In ... forward and backward flights, is provided (D) In geometrical stair, two quarter space landing is provided
Description : The ratio of average values of shear stresses produced on the bed and the banks of a channel due to flowing water is (A) Less than 1 (B) Equal to 1 (C) Greater than 1 (D) Equal to zero
Description : The diameter of the stirrups according to IS : 456-2000 should not be less than [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm
Last Answer : [ B ] 6 mm
Description : If q is the punching shear resistance per unit area a, is the side of a square footing for a column of side b, carrying a weight W including the weight of the footing, the depth (D) of the footing from punching shear consideration ... - b²)/4a²bq (C) D = W (a² - b²)/8a²bq (D) D = W (a² - b²)/4abq
Description : In turbulent flow, the (A) Fluid particles move in an orderly manner (B) Momentum transfer is on molecular scale only (C) Shear stress is caused more effectively by cohesion than momentum transfer (D) Shear stresses are generally larger than in a similar laminar flow
Last Answer : (D) Shear stresses are generally larger than in a similar laminar flow
Description : For an ordinary Portland cement (A) Residual does not exceed 10% when sieved through IS Sieve No. 9 (B) Soundness varies from 5 to 10 mm (C) Initial setting time is not less than 30 minutes (D) Compressive stress after 7 days, is not less than 175 kg/cm2
Last Answer : (C) Initial setting time is not less than 30 minutes
Description : If the average compressive strength is 4000 kg/cm2 and standard deviation is 500, the co-efficient of variation is (A) 10 % (B) 12.5 % (C) 15 % (D) 18.5%
Description : For a number of columns constructed in a rcjw, the type of foundation provided, is (A) Footing (B) Raft (C) Strap (D) Strip
Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive
Last Answer : (C) 26.67 kg/cm2 tensile
Description : The tensile force required to cause an elongation of 0.045 mm in a steel rod of 1000 mm length and 12 mm diameter, is (where E = 2 × 106 kg/cm2 ) (A) 166 kg (B) 102 kg (C) 204 kg (D) 74 kg
Last Answer : (B) 102 kg
Description : An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm
Description : If P kg/m2 is the upward pressure on the slab of a plain concrete footing whose projection on either side of the wall is a cm, the depth of foundation D is given by (A) D = 0.00775 aP (B) D = 0.0775 aP (C) D = 0.07775 aP (D) D = 0.775 Pa