What Is The Function Of A Thrust Bearing?

What Is The Function Of A Thrust Bearing?
by

1 Answer

Answer :

Thrust bearings keep the rotor in its correct axial position.
by

Related questions

Which of the following bearing will have least coefficient of friction a.Single ball bearing b.Cylinderical roller bearing c.Self aligury bearing d.Thrust ball bearing e.Tapered bearing

Description : Which of the following bearing will have least coefficient of friction a.Single ball bearing b.Cylinderical roller bearing c.Self aligury bearing d.Thrust ball bearing e.Tapered bearing

Last Answer : e. Tapered bearing

What Is A Combination Thrust And Radial Bearing?

Description : What Is A Combination Thrust And Radial Bearing?

Last Answer : This unit has the ends of the Babbitt bearing extended radically over the end of the shell. Collars on the rotor face these thrust pads, and the journal is supported in the bearing between the thrust collars.

is essential to counter act the and thrust of gang due to soil thrust. a. Gang c. Spacer b. Bearing. d. Gang bolt

Description : is essential to counter act the and thrust of gang due to soil thrust. a. Gang c. Spacer b. Bearing. d. Gang bolt

Last Answer : Bearing.

is essential to counter act the end thrust of gang due to soil thrust.. A) Spool. C ) Gang B) Bearing. D) Gang bolt

Description : is essential to counter act the end thrust of gang due to soil thrust.. A) Spool. C ) Gang B) Bearing. D) Gang bolt

Last Answer : Bearing

What is the function of a thrust bearing?

Description : What is the function of a thrust bearing?

Last Answer : Thrust bearings keep the rotor in its correct axial position.

If the bearings of an electrical generator are failing more frequently than expected and the lubricating oil is sludging then you should ______________. A. check the connections to the output leads B. check the bearing insulating block on one end of the unit C. replace the bearing with a sealed roller type D. replace the thrust bearing of the prime mover

Description : If the bearings of an electrical generator are failing more frequently than expected and the lubricating oil is sludging then you should ______________. A. check the connections to the output leads B. ... replace the bearing with a sealed roller type D. replace the thrust bearing of the prime mover

Last Answer : Answer: B

If air gap readings for an electical generating machine have changed significantly from the last reading, you should check _________. A. the bearings B. insulation readings and machine cleanliness C. the prime mover thrust bearing D. the field coil bolts for the proper torque values

Description : If air gap readings for an electical generating machine have changed significantly from the last reading, you should check _________. A. the bearings B. insulation readings and machine cleanliness C. the prime mover thrust bearing D. the field coil bolts for the proper torque values

Last Answer : Answer: A

In the illustrated motor, roller bearings are used because __________. EL-0001 A. of their ability to absorb moderate thrust loads B. they electrically insulate the rotor from the frame reducing cross-currents C. the shafting and end bells do not require as close a tolerance to properly fit this type of bearing D. the clearance between the rotor and stator is generally as close as mechanical tolerance will permit

Description : In the illustrated motor, roller bearings are used because __________. EL-0001 A. of their ability to absorb moderate thrust loads B. they electrically insulate the rotor from the frame reducing ... clearance between the rotor and stator is generally as close as mechanical tolerance will permit

Last Answer : Answer: D

Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Description : Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Last Answer : (d) All of the listed

Which one of the following bearing is intended for a very heavy radial load? (a) Ball bearing (b) Self-aligning roller bearing (c) Roller bearing (d) Thrust bearing

Description : Which one of the following bearing is intended for a very heavy radial load? (a) Ball bearing (b) Self-aligning roller bearing (c) Roller bearing (d) Thrust bearing

Last Answer : (b) Self-aligning roller bearing

Which of the following cannot take the radial load? (a) Cylindrical Roller bearing (b) Taper roller bearing (c) Thrust ball bearing (d) Spherical roller bearing

Description : Which of the following cannot take the radial load? (a) Cylindrical Roller bearing (b) Taper roller bearing (c) Thrust ball bearing (d) Spherical roller bearing

Last Answer : (c) Thrust ball bearing

Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Description : Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Last Answer : (c) Cylindrical (straight) roller bearing

Angular contact bearing can take thrust as well as radial loads. (a) True (b) False

Description : Angular contact bearing can take thrust as well as radial loads. (a) True (b) False

Last Answer : (a) True

Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Description : Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Last Answer : A. Radial load

Match List -I (Bearings) with List-II (Applications) and select the using the codes given below the lists: [IAS-1998] List –I List-II A. Journal bearing 1. Electric motors B. Thrust bearing 2. Watches C. Conical pivot bearing 3. Marine engines D. Ball bearing 4. Swivelling chairs A B C D A B C D (a) 3 4 1 2 (b) 4 2 1 3 (c) 3 4 2 1 (d) 4 2 3 1

Description : Match List -I (Bearings) with List-II (Applications) and select the using the codes given below the lists: [IAS-1998] List -I List-II A. Journal bearing 1. Electric motors B. Thrust bearing 2. Watches C. Conical pivot bearing 3. Marine ... D (a) 3 4 1 2 (b) 4 2 1 3 (c) 3 4 2 1 (d) 4 2 3 1

Last Answer : (c) 3 4 2 1

Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For hinged condition C. Deep groove ball bearing 3. For pure radial load D. Thrust ball bearing 4. For axial and radial load A B C D A B C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Description : Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For ... C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Last Answer : (c) 2 4 3 1

Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller bearing 3. Thrust load only D. Angular contact ball bearing 4. Medium to low radial and thrust combined A B C D A B C D (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Description : Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller ... (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Last Answer : (a) 2 3 1 4

Footstep bearing is an axial load bearing. a) True b) Thrust load c) Shear load d) None of the listed

Description : Footstep bearing is an axial load bearing. a) True b) Thrust load c) Shear load d) None of the listed

Last Answer : b) Thrust load

Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Description : Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Last Answer : d) All of the listed

Which of the following cannot take radial load? a) Cylindrical Roller bearing b) Taper roller bearing c) Thrust ball bearing d) None of the listed

Description : Which of the following cannot take radial load? a) Cylindrical Roller bearing b) Taper roller bearing c) Thrust ball bearing d) None of the listed

Last Answer : c) Thrust ball bearing

Angular contact bearing can take thrust as well as radial loads. a) True b) False

Description : Angular contact bearing can take thrust as well as radial loads. a) True b) False

Last Answer : a) True

A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal

Description : A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal

Last Answer : a) Thrust

The bearings which resist radial loads is known as a) Ball bearing b) bush bearing c) thrust bearing d) journal bearing

Description : The bearings which resist radial loads is known as a) Ball bearing b) bush bearing c) thrust bearing d) journal bearing

Last Answer : d) journal bearing

A bearing designed to resist axial load is known as a) Ball bearing b) bush bearing c) thrust bearing d) journal bearing

Description : A bearing designed to resist axial load is known as a) Ball bearing b) bush bearing c) thrust bearing d) journal bearing

Last Answer : c) thrust bearing

What is a tapered-land thrust bearing?

Description : What is a tapered-land thrust bearing?

Last Answer : The babbitt face of a tapered-land thrust bearing has a series of fixed pads divided by radial slots. The leading edge of each sector is tapered, allowing an oil wedge to build up and carry the thrust between the collar and pad.

What is a combination thrust and radial bearing?

Description : What is a combination thrust and radial bearing?

Last Answer : This unit has the ends of the babbitt bearing extended radially over the end of the shell. Collars on the rotor face these thrust pads, and the journal is supported in the bearing between the thrust collars.

Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true

Description : Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true

Last Answer : d) Both (b) and (c) are true

Wood is well suited to use as bearing on straw walker cranks in combine due to fact a) Wood corrosion resistance b) Split bearing are needed for practical purpose c) It can take radial as well as thrust loads d) No lubrication is required

Description : Wood is well suited to use as bearing on straw walker cranks in combine due to fact a) Wood corrosion resistance b) Split bearing are needed for practical purpose c) It can take radial as well as thrust loads d) No lubrication is required

Last Answer : b) Split bearing are needed for practical purpose

When a train is rounding a curve to prevent side thrust on the wheel flanges of cars a.Opposite thrust is created to counter balance this thrust b.Guide rail sections are provided to take care of thrust c.Thrust eliminators are provided in the train d.Outside rails are realised e.Rail section is made thick on curvature

Description : When a train is rounding a curve to prevent side thrust on the wheel flanges of cars a.Opposite thrust is created to counter balance this thrust b.Guide rail sections are provided to take care of ... are provided in the train d.Outside rails are realised e.Rail section is made thick on curvature

Last Answer : d. Outside rails are realised

It is the unbalanced force developed in a turbo jet engine that is caused by the difference in the momentum of the low-velocity air entering the engine and the high velocity exhaust gases leaving the engine.  a. Fall  b. Lift  c. Drag  d. Thrust

Description : It is the unbalanced force developed in a turbo jet engine that is caused by the difference in the momentum of the low-velocity air entering the engine and the high velocity exhaust gases leaving the engine.  a. Fall  b. Lift  c. Drag  d. Thrust

Last Answer : Thrust

A faulty 'function generator' shown in the illustration may prevent _____________. EL-0095 A. proper pitch control from both the 'bridge' and 'engine room thrust levers' B. the 'split potentiometer's' ability to control pitch C. the pitch meter from indicating accurately D. relays #2 and/or #3 from energizing

Description : A faulty 'function generator' shown in the illustration may prevent _____________. EL-0095 A. proper pitch control from both the 'bridge' and 'engine room thrust levers' B. the 'split potentiometer ... control pitch C. the pitch meter from indicating accurately D. relays #2 and/or #3 from energizing

Last Answer : Answer: A

As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay #6 C. the RPM 'function generator' and 'thrust levers' have no control D. the 'E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'

Description : As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay ... E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'

Last Answer : Answer: C

Considering the function of the circuit shown in the illustration, what is the purpose of supplying the thrust lever potentiometers with both (+) and (-) 15 volts? EL-0095 A. To select which lever (bridge or engine room) is active. B. So the circuit can differentiate between ahead and astern commands. C. To provide an alternate voltage supply if the other fails. D. So as to automatically select the position of Relay #

Description : Considering the function of the circuit shown in the illustration, what is the purpose of supplying the thrust lever potentiometers with both (+) and (-) 15 volts? EL-0095 A. To select which ... alternate voltage supply if the other fails. D. So as to automatically select the position of Relay #

Last Answer : Answer: B

As shown in the illustration, the circuit which 'shapes' the linear output of the thrust lever so that the steady-state ship speed is linear with respect to that lever's setting is the _____________. EL-0095 A. 'pitch controller' B. 'error amplifier' C. 'function generator' D. 'servo amplifier'

Description : As shown in the illustration, the circuit which 'shapes' the linear output of the thrust lever so that the steady-state ship speed is linear with respect to that lever's setting is the _____________. EL-0095 A. 'pitch controller' B. 'error amplifier' C. 'function generator' D. 'servo amplifier'

Last Answer : Answer: C

A screw jack has 4 threads per inch. The mean radius of the thread is 2.338 inches. The mean diameter of the bearing surface under the cap is 3.25 inches. What is the turning moment required to raise the bload of 150 kg ( a.5.61 kg-inch b.50.6 kg-inch c.107 dynes d.30.3 kg-inch e.23.6 kg-inch

Description : A screw jack has 4 threads per inch. The mean radius of the thread is 2.338 inches. The mean diameter of the bearing surface under the cap is 3.25 inches. What is the turning moment required to raise the bload of 150 kg ( a.5.61 kg-inch b.50.6 kg-inch c.107 dynes d.30.3 kg-inch e.23.6 kg-inch

Last Answer : b. 50.6 kg-inch

Moment of Inertia of triangular section about an axis passing through its base is given by a.bh3/12 b.bh3/32 c.bh3/36 d.None of the above e.Tapered bearing

Description : Moment of Inertia of triangular section about an axis passing through its base is given by a.bh3/12 b.bh3/32 c.bh3/36 d.None of the above e.Tapered bearing

Last Answer : a. bh3/12

A mass of 5 kg moves on a smooth horizontal plane with a speed of 8 m/s attached to a fixed point on the plane by a string of length 4m. Tension in the string is a.785 b.80N c.392.4N d.None of the above e.Tapered bearing

Description : A mass of 5 kg moves on a smooth horizontal plane with a speed of 8 m/s attached to a fixed point on the plane by a string of length 4m. Tension in the string is a.785 b.80N c.392.4N d.None of the above e.Tapered bearing

Last Answer : b. 80N

A man pulls a cart with 100 N force from rest with an acceleration of 10 m/sec2 for 10 seconds. The work done by him is a.500 KJ b.50.96 KJ c.101.92 KJ d.None of the above e.Tapered bearing

Description : A man pulls a cart with 100 N force from rest with an acceleration of 10 m/sec2 for 10 seconds. The work done by him is a.500 KJ b.50.96 KJ c.101.92 KJ d.None of the above e.Tapered bearing

Last Answer : a. 500 KJ

Power required for a train weighing 200 Mg to move at a uniform speed of 60 Kmph up an incline of 1 in 200 is (Resistance due to friction is negligible) a.16.67 KW b.163.5 KW c.1000 KW d.9810 KW e.Tapered bearing

Description : Power required for a train weighing 200 Mg to move at a uniform speed of 60 Kmph up an incline of 1 in 200 is (Resistance due to friction is negligible) a.16.67 KW b.163.5 KW c.1000 KW d.9810 KW e.Tapered bearing

Last Answer : b. 163.5 KW

A man lifts a stone weighting 300 g from the ground to a height of 2m and throws it horizontally with a velocity of 6 m/sec. The work done by the man is a.7.686 J b.11.286 J c.5.886 J d.8.343 J e.Tapered bearing

Description : A man lifts a stone weighting 300 g from the ground to a height of 2m and throws it horizontally with a velocity of 6 m/sec. The work done by the man is a.7.686 J b.11.286 J c.5.886 J d.8.343 J e.Tapered bearing

Last Answer : b. 11.286 J

Work done by a body of mass 100 kg moving along a circular path of radius 2 m with a uniform velocity of 10 m/sec is a.5000 J b.2500 J c.509.68 J d.None of the above e.Tapered bearing

Description : Work done by a body of mass 100 kg moving along a circular path of radius 2 m with a uniform velocity of 10 m/sec is a.5000 J b.2500 J c.509.68 J d.None of the above e.Tapered bearing

Last Answer : d. None of the above

M.I. of sphere of 0.5 m radius about a mutually perpendicular axis (Z-axis) when its M.I. about X-axis and Y-axis are 50 kgm2 and 50 kgm2 is a.50 Kgm2 b.Tapered bearing c.100 Kgm2 d.25 Kgm2 e.12.5 Kgm2

Description : M.I. of sphere of 0.5 m radius about a mutually perpendicular axis (Z-axis) when its M.I. about X-axis and Y-axis are 50 kgm2 and 50 kgm2 is a.50 Kgm2 b.Tapered bearing c.100 Kgm2 d.25 Kgm2 e.12.5 Kgm2

Last Answer : a. 50 Kgm2

Minimum horsepower of pump required for filling 50m3 water tank, 20 metres high from ground in 30 minutes by lifting water from a well 5 metres below the ground level is a.5.45 KW b.7.5 KW c.6.81 KW d.Tapered bearing e.66.8 KW

Description : Minimum horsepower of pump required for filling 50m3 water tank, 20 metres high from ground in 30 minutes by lifting water from a well 5 metres below the ground level is a.5.45 KW b.7.5 KW c.6.81 KW d.Tapered bearing e.66.8 KW

Last Answer : c. 6.81 KW

What Are The Advantages Of Anti-friction Bearing Over A Friction Bearing?

Description : What Are The Advantages Of Anti-friction Bearing Over A Friction Bearing?

Last Answer :  For reducing wear and tear.  For saving the power consumption.  For easy setup.  For smooth running of machine.  For running at slow and high speed carrying light and heavy loads.

What Is Journal Bearing And Mention Its Use?

Description : What Is Journal Bearing And Mention Its Use?

Last Answer : It is a split bearing having two halves which are made of brass, gun metal, etc. Its outer ends have collar on both sides. IT is fitted in the housing generally made of cast iron. It is used where the supporting pressure of the bearing is at right angle to the shaft axis.

What Is The Application Of White Metal Bearing?

Description : What Is The Application Of White Metal Bearing?

Last Answer : It is generally used on high speed with light load because its bearing metal controls the heat.

What Is The Use Of Taper Roller Bearing?

Description : What Is The Use Of Taper Roller Bearing?

Last Answer : A taper roller bearing is used to carry heavy loads because it has taper rollers instead of plain cylindrical rollers.

What Are The Functions Of A Bearing?

Description : What Are The Functions Of A Bearing?

Last Answer :  To guide the shaft.  To support the shaft.  To give free rotation to the shaft.

Why Is The Bearing Tinned Before Refilling?

Description : Why Is The Bearing Tinned Before Refilling?

Last Answer : While removing the damaged lining it helps to melt the lining at low temperature and it helps to spread over the molten metal on the bearing surface.

What Does Bearing Service Manufacture?

Description : What Does Bearing Service Manufacture?

Last Answer : Bearing Service is a distributor. We do not manufacture the products we sell, but our shops can machine, fabricate, and customize a variety of products to meet your maintenance needs.