A 10 km long line has a characteristic impedance of 400 ohms. If line length is 100 km, the characteristic

A 10 km long line has a characteristic impedance of 400 ohms. If line length is 100 km, the characteristic impedance is: (1) 4000 Ω (2) 400 Ω (3) 40 Ω (4) 4 Ω
by

1 Answer

Answer :

A 10 km long line has a characteristic impedance of 400 ohms. If line length is 100 km, the characteristic impedance is: 400 Ω

by

Related questions

The input impedance of a short circuited loss less transmission line of characteristic impedance 50 Ohm is

Description : The input impedance of a short circuited loss less transmission line of characteristic impedance 50 Ohm is

Last Answer : Capacitive

A transmission line has 1 P.0 impedance on a base of 11 KV, 100 MVA. On a base of 55 KV. it will have a P.0 impedance of

Description : A transmission line has 1 P.0 impedance on a base of 11 KV, 100 MVA. On a base of 55 KV. it will have a P.0 impedance of

Last Answer : A transmission line has 1 P.0 impedance on a base of 11 KV, 100 MVA. On a base of 55 KV. it will have a P.0 impedance of 0.02 P.U

The parameters of Transmission line are R = 50 Ω/ km, L= 1mH/km ,C = 0.1µf/km, G = 2µV/km. calculate characteristic impedance.

Description : The parameters of Transmission line are R = 50 Ω/ km, L= 1mH/km ,C = 0.1µf/km, G = 2µV/km. calculate characteristic impedance.

Last Answer : The parameters of Transmission line are R = 50 Ω/ km, L= 1mH/km ,C = 0.1µf/km, G = 2µV/km. calculate characteristic impedance.

If the insulation resistance of a cable of length 10 km is 1 mega ohm, its insulation resistance

Description : If the insulation resistance of a cable of length 10 km is 1 mega ohm, its insulation resistance for 50 km length will be

Last Answer : If the insulation resistance of a cable of length 10 km is 1 mega ohm, its insulation resistance for 50 km length will be 0.2 mega ohm

For an overhead line, the surge impedance is taken as (a) 20-30 ohms (b) 70—80 ohms (c) 100—200 ohms (d) 500—1000 ohms (e) none of the above

Description : For an overhead line, the surge impedance is taken as (a) 20-30 ohms (b) 70—80 ohms (c) 100—200 ohms (d) 500—1000 ohms (e) none of the above

Last Answer : (c) 100—200 ohms

Why is the physical length of a coaxial cable transmission line shorter than its electrical length?A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the coaxial cable C. The surge impedance is higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Description : Why is the physical length of a coaxial cable transmission line shorter than its electrical length? A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the ... higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Last Answer : B. RF energy moves slower along the coaxial cable

The inductance of single phase two wire power transmission line per km gets doubled when the

Description : The inductance of single phase two wire power transmission line per km gets doubled when the  (a) Distance between wires is doubled  (b) Distance between the wires is increased four fold  (c) ... the wires is increased as square of the original distance  (d) Radius of the wire is doubled

Last Answer : The inductance of single phase two wire power transmission line per km gets doubled when the Distance between the wires is increased as square of the original distance 

For 11kV line the inductance per km per phase will be of the order of:

Description : For 11kV line the inductance per km per phase will be of the order of:  (A) 1 H (B) 0.1 H (C) 1 mH (D) 0.1 mH

Last Answer : For 11kV line the inductance per km per phase will be of the order of: 1 mH

For 11 kV line the capacitance per km per phase will be of the order of:

Description : For 11 kV line the capacitance per km per phase will be of the order of:  (A) 1 Farad (B) 0.1 Farad (C) 0.01 Farad (D) 0.01 microF

Last Answer : For 11 kV line the capacitance per km per phase will be of the order of: 0.01 Farad

For a transmission line open circuit and short circuit impedances are 20 Ω and 5 Ω. Then characteristic

Description : For a transmission line open circuit and short circuit impedances are 20 Ω and 5 Ω. Then characteristic impedance is: (1) 100 Ω (2) 50 Ω (3) 25 Ω (4) 10 Ω

Last Answer : For a transmission line open circuit and short circuit impedances are 20 Ω and 5 Ω. Then characteristic impedance is: 10 Ω

An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Description : An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Last Answer : Answer: B

Which of the following is true for a bus impedance matrix ?

Description : Which of the following is true for a bus impedance matrix ?  (A) It is sparse  (B) It has diagonally dominant elements  (C) It is the inverse of the bus admittance matrix  (D) Each element of it is the reciprocal of the corresponding element in admittance matrix

Last Answer : Which of the following is true for a bus impedance matrix ?  (A) It is sparse  (B) It has diagonally dominant elements  (C) It is the inverse of the bus admittance matrix  (D) Each element of it is the reciprocal of the corresponding element in admittance matrix

Which of the following is not common transmission line impedance? A. 50 ohms B. 120 ohms C. 75 ohms D. 650 ohms

Description : Which of the following is not common transmission line impedance? A. 50 ohms B. 120 ohms C. 75 ohms D. 650 ohms

Last Answer : B. 120 ohms

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'Y'? EL-0047 A. 220 ohms B. 240 ohms C. 2,400 ohms D. 24,000 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'Y'? EL-0047 A. 220 ohms B. 240 ohms C. 2,400 ohms D. 24,000 ohms

Last Answer : Answer: C

A transformer has a turns ratio of two to one. If a 100 ohm resistor is connected on the high side, its resistance as measured on the low side would be: w) 25 ohms x) 50 ohms y) 100 ohms z) 400 ohms

Description : A transformer has a turns ratio of two to one. If a 100 ohm resistor is connected on the high side, its resistance as measured on the low side would be: w) 25 ohms x) 50 ohms y) 100 ohms z) 400 ohms

Last Answer : ANSWER: W -- 25 OHMS

A 40 kVA transformer has a core loss of 400 W and a full load copper loss of 800 W. The

Description : A 40 kVA transformer has a core loss of 400 W and a full load copper loss of 800 W. The proportion of full load at maximum efficiency is

Last Answer : A 40 kVA transformer has a core loss of 400 W and a full load copper loss of 800 W. The proportion of full load at maximum efficiency is 0.707

For a space wave transmission, the radio horizon distance of a transmitting antenna with a height of 100 meters is approximately:A. 10 km B. 40 km C. 100 km D. 400 km

Description : For a space wave transmission, the radio horizon distance of a transmitting antenna with a height of 100 meters is approximately: A. 10 km B. 40 km C. 100 km D. 400 km

Last Answer : B. 40 km

A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Description : A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Last Answer : Answer: B

A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Description : A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Last Answer : Answer: B

What is the diameter of a copper wire to be used in a 16 km loop with a dc loop resistance of 100 ohms/km? A. 0.108 cm B. 1.082 cm C. 0.017 cm D. 0.0465 cm

Description : What is the diameter of a copper wire to be used in a 16 km loop with a dc loop resistance of 100 ohms/km? A. 0.108 cm B. 1.082 cm C. 0.017 cm D. 0.0465 cm

Last Answer : D. 0.0465 cm

If 3000 kW power is to be transmitted over a distance of 30 km, the desirable transmission voltage will be.

Description : If 3000 kW power is to be transmitted over a distance of 30 km, the desirable transmission voltage will be.  (A) 11 kV (B) 33 kV (C) 66 kV (D) 132 kV

Last Answer : By

Calculate the characteristics impedance for a transmission line having L=0.5 mH/Km, C=0.08 µF and negligible R and G.

Description : Calculate the characteristics impedance for a transmission line having L=0.5 mH/Km, C=0.08 µF and negligible R and G.

Last Answer : L=0.5 mH/Km C=0.08 µF

When a transmission line has a load impedance same as that of the characteristic impedance, the line is said to be a) Parallel b) Perpendicular c) Polarized d) Matched

Description : When a transmission line has a load impedance same as that of the characteristic impedance, the line is said to be a) Parallel b) Perpendicular c) Polarized d) Matched

Last Answer : Ans: D

What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150Ω D. 2 Ω

Description : What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150 Ω D. 2 Ω

Last Answer : C. 150 Ω

What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Description : What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Last Answer : A. Velocity factor

What is the meaning of the term “velocity factor” of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial cable. C. The velocity of the wave on the transmission line multiplied by the velocity of light in a vacuum. D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Description : What is the meaning of the term velocity factor of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

What is the characteristic impedance of a coaxial line with the following data: inner diameter = 0.2 in., center conductor diameter = 0.06 in., insulation = Teflon. A. 200Ω B. 75Ω C. 50Ω D. 150Ω

Description : What is the characteristic impedance of a coaxial line with the following data: inner diameter = 0.2 in., center conductor diameter = 0.06 in., insulation = Teflon. A. 200Ω B. 75Ω C. 50Ω D. 150Ω

Last Answer : C. 50Ω

What is the characteristic impedance of a two-wire line with the following data: diameter = 0.023in., spacing =0.5 in., insulation = PE.? A. 300Ω B. 250Ω C. 305Ω D. 301Ω

Description : What is the characteristic impedance of a two-wire line with the following data: diameter = 0.023in., spacing =0.5 in., insulation = PE.? A. 300Ω B. 250Ω C. 305Ω D. 301Ω

Last Answer : D. 301Ω

What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of light in vacuum C. The ratio of the characteristic impedance of the line to the terminating impedance D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Description : What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Referred to the dielectric constant of a transmission line material. A. Inductance and capacitance B. Velocity factor C. Characteristic impedance D. Propagation velocity

Description : Referred to the dielectric constant of a transmission line material. A. Inductance and capacitance B. Velocity factor C. Characteristic impedance D. Propagation velocity

Last Answer : B. Velocity factor

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

If the terminating impedance is exactly equal to the characteristic impedance of the transmission line the return loss is ___________. A. zero B. one C. infinite D. None of these

Description : If the terminating impedance is exactly equal to the characteristic impedance of the transmission line the return loss is ___________. A. zero B. one C. infinite D. None of these

Last Answer : C. infinite

What symbol is used to designate the characteristic impedance of a line, and what two variables does it compare?

Description : What symbol is used to designate the characteristic impedance of a line, and what two variables does it compare?

Last Answer : Z0 and it is the ratio of E to I at every point along the line.

In swept-frequency testing the impedance of a transmission line, what electrical characteristic is actually being measured?

Description : In swept-frequency testing the impedance of a transmission line, what electrical characteristic is actually being measured?

Last Answer : Swr on the transmission line.

Short-circuited stubs are preferred to open-circuited stubs because thelatter are a. more difficult to make an connect b. made of a transmission line with a different characteristic impedance c. liable to radiate

Description : Short-circuited stubs are preferred to open-circuited stubs because thelatter are a. more difficult to make an connect b. made of a transmission line with a different characteristic impedance c. liable to radiate

Last Answer : c. liable to radiate

A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Description : A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Last Answer : Solution :

A transmission line is terminated at its characteristic impedance. The reflection coefficient is

Description : A transmission line is terminated at its characteristic impedance. The reflection coefficient is  (a) 1 (b) –1 (c) 0 (d) ∞

Last Answer : A transmission line is terminated at its characteristic impedance. The reflection coefficient is  0

A loss less line of characteristic impedance Z0 is terminated in pure reactance of –jZ0 value. VSWR is

Description : A loss less line of characteristic impedance Z0 is terminated in pure reactance of –jZ0 value. VSWR is  (1) 10 (2) 2 (3) 1 (4) Infinity

Last Answer : A loss less line of characteristic impedance Z0 is terminated in pure reactance of –jZ0 value. VSWR is Infinity.

A 10 kVA, 400 V/200 V single phase transformer with 10% impedance draws a steady

Description : A 10 kVA, 400 V/200 V single phase transformer with 10% impedance draws a steady short-circuit line current of   (a) 250A (b) 50 A (c) 150 A (d) 350 A 

Last Answer : A 10 kVA, 400 V/200 V single phase transformer with 10% impedance draws a steady short-circuit line current of 250A

Electromagnetic wave travel at __________ in free space. A. 300,000 km/sec B. 100,000 km/ sec C. 400,000 km/sec D. 200km/sec

Description : Electromagnetic wave travel at __________ in free space. A. 300,000 km/sec B. 100,000 km/ sec C. 400,000 km/sec D. 200km/sec

Last Answer : A. 300,000 km/sec

The normal altitude of GPS satellite is about (A) 16,200 km (B) 20,200 km (C) 24,400 km (D) 36,100 km

Description : The normal altitude of GPS satellite is about (A) 16,200 km (B) 20,200 km (C) 24,400 km (D) 36,100 km

Last Answer : Answer: Option B

. The product of the bit rate and distance of a fiber-optic system is 2 Gbits-km/s. What is the maximum rate at 5 km? ∙ A. 100 Mbits/s ∙ B. 200 Mbits/s ∙ C. 400 Mbits/s ∙ D. 1000 Gbits/s

Description : . The product of the bit rate and distance of a fiber-optic system is 2 Gbits-km/s. What is the maximum rate at 5 km? ∙ A. 100 Mbits/s ∙ B. 200 Mbits/s ∙ C. 400 Mbits/s ∙ D. 1000 Gbits/s

Last Answer : C. 400 Mbits/s

The product of the bit rate and distance of a fiber-optic system is 2 Gbits km/s. What is the maximum rate at 5 km? ∙ a. 100 Mbits/s ∙ b. 200 Mbits/s ∙ c. 400 Mbits/s ∙ d. 1000 Gbits/s

Description : The product of the bit rate and distance of a fiber-optic system is 2 Gbits km/s. What is the maximum rate at 5 km? ∙ a. 100 Mbits/s ∙ b. 200 Mbits/s ∙ c. 400 Mbits/s ∙ d. 1000 Gbits/s

Last Answer : c. 400 Mbits/s

The power supplied to a motor is six kilowatts at 120 volts. What is the impedance of the motor? A. 0.05 Ohms B. 0.50 Ohms C. 2.40 Ohms D. 24.00 Ohms

Description : The power supplied to a motor is six kilowatts at 120 volts. What is the impedance of the motor? A. 0.05 Ohms B. 0.50 Ohms C. 2.40 Ohms D. 24.00 Ohms

Last Answer : Answer: C

When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage is being measured B. input impedance much less than the impedance across which the voltage is being measured C. sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Description : When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage ... sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Last Answer : Answer: A

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

What is the input terminal impedance at the center if a folded dipole antenna? A. 300 ohms B. 72 ohms C. 50 ohms D. 450 ohms

Description : What is the input terminal impedance at the center if a folded dipole antenna? A. 300 ohms B. 72 ohms C. 50 ohms D. 450 ohms

Last Answer : A. 300 ohms

What is the impedance in ohms of a transformer marked for 25V, 4W, when the secondary is correctly loaded? A. 150 Ω B. 156 Ω C. 160 Ω D. 165 Ω

Description : What is the impedance in ohms of a transformer marked for 25V, 4W, when the secondary is correctly loaded? A. 150 Ω B. 156 Ω C. 160 Ω D. 165 Ω

Last Answer : B. 156 Ω

What is the impedance of a one microfarad capacitor at 60 Hertz: w) 16,700 ohms x) 2,650 ohms y) 3.8x10-4 ohms z) 6x10-5 ohms

Description : What is the impedance of a one microfarad capacitor at 60 Hertz: w) 16,700 ohms x) 2,650 ohms y) 3.8x10-4 ohms z) 6x10-5 ohms

Last Answer : ANSWER: X -- 2,650 OHMS

A coil is wound with 400 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 4.8 amps B. 7.06 amps C. 10.65 amps D. 11.27 amps

Description : A coil is wound with 400 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 4.8 amps B. 7.06 amps C. 10.65 amps D. 11.27 amps

Last Answer : Answer: B