According to ISI recommendations, the maximum depth of stress block for balanced section of a beam of effective depth d is (A) 0.43 d (B) 0.55 d (C) 0.68 d (D) 0.85 d

According to ISI recommendations, the maximum depth of stress block for balanced section of a
beam of effective depth d is
(A) 0.43 d
(B) 0.55 d
(C) 0.68 d
(D) 0.85 d
by

1 Answer

Answer :

Answer: Option A
by

Related questions

According to Whitney's theory, depth of stress block for a balanced section of a concrete beam is limited to (A) 0.43 d (B) 0.537 d (C) 0.68 d (D) 0.85 d Where d is effective depth of beam

Description : According to Whitney's theory, depth of stress block for a balanced section of a concrete beam is limited to (A) 0.43 d (B) 0.537 d (C) 0.68 d (D) 0.85 d Where d is effective depth of beam

Last Answer : Answer: Option B

A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2 , the area of steel required, is (A) 14 cm(B) 15 cm2(C) 16 cm2(D) 17 cm

Description : A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2 ... area of steel required, is (A) 14 cm (B) 15 cm2 (C) 16 cm2 (D) 17 cm

Last Answer : Answer: Option C

An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity of shear stress, is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2

Description : An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity ... , is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2

Last Answer : Answer: Option A

The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio is 18, then the stress developed in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2

Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2

Last Answer : (b) 135N/mm2

Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach its maximum permissible value first. (c) The moment of resistance will be less than that of the balanced section. (d) The concrete on the tension side is also be considered for calculating the moment of resistance of the section.

Description : Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach ... on the tension side is also be considered for calculating the moment of resistance of the section.

Last Answer : both b&c

If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also

Description : If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also

Last Answer : Answer: Option B

At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of the section by (A) Depth of the section (B) Depth of the neutral axis (C) Maximum tensile stress at the section (D) Maximum compressive stress at the section

Description : At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of  the section by  (A) Depth of the section  (B) Depth of the neutral axis  (C) Maximum tensile stress at the section  (D) Maximum compressive stress at the section

Last Answer : (B) Depth of the neutral axis 

In a singly reinforced beam, if the stress in concrete reaches its allowable limit later than the steel reaches, its permissible value, the beam section is said to be (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section

Description : In a singly reinforced beam, if the stress in concrete reaches its allowable limit later than the steel reaches, its permissible value, the beam section is said to be (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section

Last Answer : (b) Over-reinforced section

In a singly reinforced beam, if the permissible stress in steel reaches earlier than that of concrete, the beam section as called [ A ] Under reinforced section [ B ] Over reinforced section [ C ] Balanced section [ D ] Critical section

Description : In a singly reinforced beam, if the permissible stress in steel reaches earlier than that of concrete, the beam section as called [ A ] Under reinforced section [ B ] Over reinforced section [ C ] Balanced section [ D ] Critical section

Last Answer : [ A ] Under reinforced section

In a Singly reinforced beam, if the permissible stress in concrete reaches earlier than that in steel, the beam section is called [ A ] Under reinforced section [ B ] Over reinforced section [ C ] Balanced section [ D ] Critical section

Description : In a Singly reinforced beam, if the permissible stress in concrete reaches earlier than that in steel, the beam section is called [ A ] Under reinforced section [ B ] Over reinforced section [ C ] Balanced section [ D ] Critical section

Last Answer : [ B ] Over reinforced section

An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Description : An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Last Answer : Answer: Option D

The ratio of the depth of flow to the diameter of the channel for maximum discharge in a circular channel in open channel flow is (A) 0.1 (B) 0.55(C) 0.95 (D) 1.85

Description : The ratio of the depth of flow to the diameter of the channel for maximum discharge in a circular channel in open channel flow is (A) 0.1 (B) 0.55 (C) 0.95 (D) 1.85

Last Answer : (C) 0.95

A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Description : A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Last Answer : b. 5208 Mpa

If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Description : If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Last Answer : Answer: Option D

For an over –reinforced (singly reinforced )rectangular reinforced concrete section (a) The lever arm will be less than that for a balanced section (b) The maximum stress developed by concrete will be equal to allowable stress in concrete (c) The maximum stress developed by steel will be equal to the allowable (d) All the above

Description : For an over -reinforced (singly reinforced )rectangular reinforced concrete section (a) The lever arm will be less than that for a balanced section (b) The maximum stress developed by concrete will be equal ... c) The maximum stress developed by steel will be equal to the allowable (d) All the above

Last Answer : (b) The maximum stress developed by concrete will be equal to allowable stress in concrete

The section in which concrete is not fully stressed to its permissible value when stress in steel reaches its maximum value is (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section

Description : The section in which concrete is not fully stressed to its permissible value when stress in steel reaches its maximum value is (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section

Last Answer : (a) Under-reinforced section

A T-section beam having flange 180mm wide and 20 mm thick and web 150 mm long and 20 mm thick carries a udl of 80 kN/m over an effective span of 8 m. Calculate the maximum bending stress.

Description : A T-section beam having flange 180mm wide and 20 mm thick and web 150 mm long and 20 mm thick carries a udl of 80 kN/m over an effective span of 8 m. Calculate the maximum bending stress.

Last Answer : Solution :

If the depth of actual neutral axis in a beam is more than the depth of critical neutral axis, then the beam is called (A) Balanced beam (B) Under-reinforced beam (C) Over-reinforced beam (D) None of the above

Description : If the depth of actual neutral axis in a beam is more than the depth of critical neutral axis, then the beam is called (A) Balanced beam (B) Under-reinforced beam (C) Over-reinforced beam (D) None of the above

Last Answer : Option C

If the depth of actual axis in a beam is more than the depth of critical axis, then the beam is called (a) Over reinforced beam (b) Under-reinforced beam (c) Balanced beam (d) Deep beam

Description : If the depth of actual axis in a beam is more than the depth of critical axis, then the beam is called (a) Over reinforced beam (b) Under-reinforced beam (c) Balanced beam (d) Deep beam

Last Answer : (a) Over reinforced beam

The ratio of the length and depth of a simply supported rectangular beam which experiences maximum bending stress equal to tensile stress, due to same load at its mid span, is (A) 1/2 (B) 2/3 (C) 1/4 (D) 1/3

Description : The ratio of the length and depth of a simply supported rectangular beam which experiences  maximum bending stress equal to tensile stress, due to same load at its mid span, is  (A) 1/2  (B) 2/3  (C) 1/4  (D) 1/3

Last Answer : (B) 2/3 

The maximum compressive stress at the top of a beam is 1600 kg/cm2 and the corresponding tensile stress at its bottom is 400 kg/cm2 . If the depth of the beam is 10 cm, the neutral axis from the top, is(A) 2 cm (B) 4 cm (C) 6 cm (D) 8 cm

Description : The maximum compressive stress at the top of a beam is 1600 kg/cm2 and the corresponding tensile stress at its bottom is 400 kg/cm2 . If the depth of the beam is 10 cm, the neutral axis from the top, is (A) 2 cm (B) 4 cm (C) 6 cm (D) 8 cm

Last Answer : (D) 8 cm

A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is (A) 15 cm (B) 20 cm (C) 25 cm (D) 30 cm

Description : A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is (A) 15 cm (B) 20 cm (C) 25 cm (D) 30 cm

Last Answer : (C) 25 cm

A 8 metre long simply supported rectangular beam which carries a distributed load 45 kg/m. experiences a maximum fibre stress 160 kg/cm2 . If the moment of inertia of the beam is 640 cm4 , the overall depth of the beam is (A) 10 cm (B) 12 cm (C) 15 cm (D) 18 cm

Description : A 8 metre long simply supported rectangular beam which carries a distributed load 45 kg/m. experiences a maximum fibre stress 160 kg/cm2 . If the moment of inertia of the beam is 640 cm4 , the overall depth of the beam is (A) 10 cm (B) 12 cm (C) 15 cm (D) 18 cm

Last Answer : (A) 10 cm

If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less than the depth of critical neutral axis, the steel in the tensile zone attains its maximum stress earlier (C) Is equal to the depth of critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Description : If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less ... critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Last Answer : Answer: Option D

The section of a reinforced beam where most distant concrete fibre in compression and tension in steel attains permissible stresses simultaneously, is called (A) Balanced sectionB) Economic section (C) Critical section (D) All the above

Description : The section of a reinforced beam where most distant concrete fibre in compression and tension in steel attains permissible stresses simultaneously, is called (A) Balanced section B) Economic section (C) Critical section (D) All the above

Last Answer : Answer: Option D

In a beam section, if the steel reinforcement is of such a magnitude that the permissible stresses in concrete and steel are developed simultaneously, the section is. (a) Balanced section (b) Economical section (c) Critical section (d) All the above

Description : In a beam section, if the steel reinforcement is of such a magnitude that the permissible stresses in concrete and steel are developed simultaneously, the section is. (a) Balanced section (b) Economical section (c) Critical section (d) All the above

Last Answer : (d) All the above

The section of a reinforced beam where most distant concrete fiber in compression and tension in steel attains permissible stresses simultaneously is called (i)Balanced section (ii)Economic section (iii)Critical section [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : The section of a reinforced beam where most distant concrete fiber in compression and tension in steel attains permissible stresses simultaneously is called (i)Balanced section (ii)Economic section (iii)Critical section [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

With usual notations the depth of the neutral axis of a balanced section, is given by (A) mc/t = (d - n)/n (B) t/mc = (d - n)/n (C) t/mc = (d + n)/n (D) mc/t = n/(d - n)

Description : With usual notations the depth of the neutral axis of a balanced section, is given by (A) mc/t = (d - n)/n (B) t/mc = (d - n)/n (C) t/mc = (d + n)/n (D) mc/t = n/(d - n)

Last Answer : Answer: Option D

In general, the depth of slab should be ---------------- the minimum depth required for balanced section. [ A ] Equal to [ B ] Less than [ C ] Greater than [ D ] Half of

Description : In general, the depth of slab should be ---------------- the minimum depth required for balanced section. [ A ] Equal to [ B ] Less than [ C ] Greater than [ D ] Half of

Last Answer : [ C ] Greater than

The depth of neutral axis for a balanced section is --------- the depth of critical neutral axis [ A ] equal [ B ] always greater than [ C ] always less than [ D ] may be sometimes greater than

Description : The depth of neutral axis for a balanced section is --------- the depth of critical neutral axis [ A ] equal [ B ] always greater than [ C ] always less than [ D ] may be sometimes greater than

Last Answer : [ A ] equal

According to ISI method of measurement, the order of the sequence is (A) Length, breadth, height (B) Breadth, length, height (C) Height, length, breadth (D) None of these

Description : According to ISI method of measurement, the order of the sequence is (A) Length, breadth, height (B) Breadth, length, height (C) Height, length, breadth (D) None of these

Last Answer : (A) Length, breadth, height

According to ISI, bitumen is classified into (A) 2 grades (B) 4 grades (C) 8 grades (D) 10 grades

Description : According to ISI, bitumen is classified into (A) 2 grades (B) 4 grades (C) 8 grades (D) 10 grades

Last Answer : Answer: Option D

The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of 4 tonnes at the centre. The maximum stress in the bottom most fibre at the mid span section, is (A) 13.33 kg/cm2 tensile (B) 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Last Answer : (C) 26.67 kg/cm2 tensile

When a rectangular beam is loaded transversely, the maximum compressive stress develops on (A) Bottom fibre (B) Top fibre (C) Neutral axis (D) Every cross-section

Description : When a rectangular beam is loaded transversely, the maximum compressive stress develops on (A) Bottom fibre (B) Top fibre (C) Neutral axis (D) Every cross-section

Last Answer : (B) Top fibre

While testing a cast iron beam (2.5 cm × 2.5 cm) in section and a metre long simply supported at the ends failed when a 100 kg weight is applied at the centre. The maximum stress induced is: (A) 960 kg/cm2 (B) 980 kg/cm2 (C) 1000 kg/cm2 (D) 1200 kg/cm2 Answer: Option

Description : While testing a cast iron beam (2.5 cm × 2.5 cm) in section and a metre long simply supported at  the ends failed when a 100 kg weight is applied at the centre. The maximum stress induced is:  (A) 960 kg/cm2 (B) 980 kg/cm2 (C) 1000 kg/cm2 (D) 1200 kg/c

Last Answer : (A) 960 kg/cm

A cast iron T section beam is subjected to pure bending. For maximum compressive stress to be three times the maximum tensile stress, centre of gravity of the section from flange side is (A) h/4 (B) h/3 (C) h/2 (D) 2/3 h

Description : A cast iron T section beam is subjected to pure bending. For maximum compressive stress to be  three times the maximum tensile stress, centre of gravity of the section from flange side is  (A) h/4  (B) h/3  (C) h/2  (D) 2/3 h

Last Answer : (A) h/4 

is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The maximum stress in the beam, subjected to a maximum bending moment , is (A) f = (P/A) + (Z/M) (B) f = (A/P) + (M/Z) (C) f = (P/A) + (M/Z) (D) f = (P/A) + (M/6Z)

Description : is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The maximum stress in the beam, subjected to a maximum bending moment , is (A) f = (P/A) + (Z/M) ... ) + (M/Z) (C) f = (P/A) + (M/Z) (D) f = (P/A) + (M/6Z)

Last Answer : Answer: Option C

is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is (A) f = (P/A) - (Z/M) (B) f = (A/P) - (M/Z) (C) f = (P/A) - (M/Z) (D) f = (P/A) - (M/6Z)

Description : is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is (A) f = (P/A) - (Z/M) (B) f = (A/P) - (M/Z) (C) f = (P/A) - (M/Z) (D) f = (P/A) - (M/6Z)

Last Answer : Answer: Option C

For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.

Description : For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.

Last Answer : (b) Parabolic above the neutral axis and rectangular below the neutral axis.

A triangular section having base b, height h, is placed with its base horizontal. If the shear stress at a depth y from top is q, the maximum shear stress is (A) 3S/bh (B) 4S/bh (C) 4b/Sh (D) 3b/bS

Description : A triangular section having base b, height h, is placed with its base horizontal. If the shear stress at a depth y from top is q, the maximum shear stress is (A) 3S/bh (B) 4S/bh (C) 4b/Sh (D) 3b/bS

Last Answer : (A) 3S/bh

A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of rigidity is 80 GPa. The outside diameter (in mm) of the shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Last Answer : (a) 43 to 45

The critical section for finding maximum bending moment for footing under masonry wall is located (A) At the middle of the wall (B) At the edge of the wall (C) Halfway between the middle and edge of the wall (D) At a distance equal to effective depth of footing from the edge of the wall

Description : The critical section for finding maximum bending moment for footing under masonry wall is located (A) At the middle of the wall (B) At the edge of the wall (C) Halfway between the middle and edge of the wall (D) At a distance equal to effective depth of footing from the edge of the wall

Last Answer : Answer: Option C

If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm(C) 150 cm (D) 200 cm

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm (C) 150 cm (D) 200 cm

Last Answer : Answer: Option C

If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Last Answer : Answer: Option C

A continuous beam shall be deemed to be a deep beam if the ratio of effective span to overall depth, is (A) 2.5 (B) 2.0 (C) Less than 2 (D) Less than 2.5

Description : A continuous beam shall be deemed to be a deep beam if the ratio of effective span to overall depth, is (A) 2.5 (B) 2.0 (C) Less than 2 (D) Less than 2.5

Last Answer : Answer: Option A

The ratio of the breadth to effective depth of a beam is kept (A) 0.25 (B) 0.50 (C) 0.70 (D) 0.75

Description : The ratio of the breadth to effective depth of a beam is kept (A) 0.25 (B) 0.50 (C) 0.70 (D) 0.75

Last Answer : Answer: Option B

A continuous beam is deemed to be a deep beam when the ratio of effective span to overall depth (1/D) is less than (A) 1.5 (B) 2.0 (C) 2.5 (D) 3.0

Description : A continuous beam is deemed to be a deep beam when the ratio of effective span to overall depth (1/D) is less than (A) 1.5 (B) 2.0 (C) 2.5 (D) 3.0

Last Answer : Answer: Option C

In limit state design of concrete for flexure, the area of stress block is taken as (a) 0.530 fck. Xu (b) 0.446 fck . Xu ( c) 0.420 fck .Xu (d) 0.360 fck . Xu Where fck is characteristic compressive strength of concrete and Xu is the depth of neutral axis from top.

Description : In limit state design of concrete for flexure, the area of stress block is taken as (a) 0.530 fck. Xu (b) 0.446 fck . Xu ( c) 0.420 fck .Xu (d) 0.360 fck . Xu Where fck is characteristic compressive strength of concrete and Xu is the depth of neutral axis from top.

Last Answer : (d) 0.360 fck . Xu

For a balanced section, the tensile stress in the reinforcement [ A ] reaches its allowable stress [ B ] is always less than its allowable stress [ C ] may be greater than its allowable stress [ D ] none of the above

Description : For a balanced section, the tensile stress in the reinforcement [ A ] reaches its allowable stress [ B ] is always less than its allowable stress [ C ] may be greater than its allowable stress [ D ] none of the above

Last Answer : [ A ] reaches its allowable stress

The average shear stress in a beam of circular section is _______ times the maximum shear stress. a. 0.75 b. 1.5 c. 4/3 d. equa

Description : The average shear stress in a beam of circular section is _______ times the maximum shear stress. a. 0.75 b. 1.5 c. 4/3 d. equa

Last Answer : a. 0.75