What are necessary parts of inlet line of compressor?

What are necessary parts of inlet line of compressor?
by

1 Answer

Answer :

Answer: Block Valve, Strainer, Break out flanges in both inlet and outlet to remove casing covers, Straightening vane in inlet line if not enough straight piece in inlet line available, PSV in interstage line and in discharge line before block valve.
by

Related questions

What are the types of compressor shelters?

Description : What are the types of compressor shelters?

Last Answer : Answer: On ground with no shelter, Open sided structure with a roof, Curtain wall structure (Temperate climates), Open elevated installation, Elevated multi-compressor structure.

What points to be considered for reciprocating compressor piping layout?

Description : What points to be considered for reciprocating compressor piping layout?

Last Answer : Answer: High pulsation, simple line as low to grade as possible for supporting, analog study, all branches close to line support and on top, Isolate line support from adjacent compressor or building foundations

What are the types of compressor cases?

Description : What are the types of compressor cases?

Last Answer : Answer: Horizontal split case, Vertical split case.

What are the compressor housing design points?

Description : What are the compressor housing design points?

Last Answer : Answer: Floor elevation, building width, building elevation, hook centerline elevation.

What factors to be considered while designing compressor housing?

Description : What factors to be considered while designing compressor housing?

Last Answer : Answer: Operation, Maintenance, Climate conditions, Safety, Economics.

What are the auxiliary equipments of compressor?

Description : What are the auxiliary equipments of compressor?

Last Answer : Answer: Lube oil consoles, Seal oil consoles, Surface condensers, Condensate pump, Air blowers, Inlet air filters, waste heat system, compressor suction drum, knock out pot, Pulsation dampner, volume bottles, Inter and after coolers.

What are types of compressor drives?

Description : What are types of compressor drives?

Last Answer : Answer: Electric motor, gas turbine, steam turbine and gas engine.

What are necessary nozzles for pressure vessel?

Description : What are necessary nozzles for pressure vessel?

Last Answer : Answer: Inlet, outlet, manhole, drain, pressure relief, agitator, level gauge, pressure gauge, temperature element, vent and for steam-out.

What are necessary nozzles for non-pressure vessel?

Description : What are necessary nozzles for non-pressure vessel?

Last Answer : Answer: Inlet, outlet, vent, manhole, drain, overflow, agitator, temperature element, level instrument, and steam-out connection.

What are wetted parts of valve?

Description : What are wetted parts of valve?

Last Answer : Answer: All parts that come in contact with surface fluid are called wetted parts.

What are wetted parts of valve?

Description : What are wetted parts of valve?

Last Answer : Answer: All parts that come in contact with surface fluid are called wetted parts.

In centrifugal compressor terminology, vaneless space refers to the space between A. The inlet and blade inlet edge B. Blades in the impeller C. Diffuser exit and volute casing D. Impeller tip and diffuser inlet edge

Description : In centrifugal compressor terminology, vaneless space refers to the space between A. The inlet and blade inlet edge B. Blades in the impeller C. Diffuser exit and volute casing D. Impeller tip and diffuser inlet edge

Last Answer : ANSWER : D

The variable required to be known in correlations used for estimating the horse power of a centrifugal gas compressor and hence its cost is P. Inlet pressure Q. Compressor rpm R. Delivery pressure S. Volumetric flow rate at inlet. (A) P, Q and R (B) P and R (C) R and S (D) P, Rand S

Description : The variable required to be known in correlations used for estimating the horse power of a centrifugal gas compressor and hence its cost is P. Inlet pressure Q. Compressor rpm R. Delivery pressure S. Volumetric flow rate at inlet. (A) P, Q and R (B) P and R (C) R and S (D) P, Rand S

Last Answer : (A) P, Q and R

Can you explain how temperature of inlet air affects the energy consumption of an air compressor?

Description : Can you explain how temperature of inlet air affects the energy consumption of an air compressor?

Last Answer : As a thumb rule “for every 4 °C rise in inlet air temperature results in a higher energy consumption by 1% to achieve equivalent output”. Hence cool air intake leads to a more efficient compression.

Which of the statement is “True” for centrifugal compressors? a) The compressor should not be operated at full load b) The compressor should be operated at shut off pressure c) The compressor should not be operated with inlet-guide vane control d) The compressor should not be operated close to the surge point

Description : Which of the statement is True for centrifugal compressors? a) The compressor should not be operated at full load b) The compressor should be operated at shut off pressure c) The ... operated with inlet-guide vane control d) The compressor should not be operated close to the surge point 

Last Answer : d) The compressor should not be operated close to the surge point

For every 4°C raise in air inlet temperature of an air compressor, the power consumption will increases by_____ a) 2% b) 1% c) 3% d) 4%

Description : For every 4°C raise in air inlet temperature of an air compressor, the power consumption will increases by_____ a) 2% b) 1% c) 3% d) 4%

Last Answer : b) 1%

What are the types of bonnets?

Description : What are the types of bonnets?

Last Answer : Answer: Bolted bonnet, bellow sealed bonnet, screwed on bonnet, union bonnets, A U-bolt and clamp type bonnet, breech-lock bonnet, pressure seal bonnet

What are types of gate valves?

Description : What are types of gate valves?

Last Answer : Answer: Solid plane wedge, solid flexible wedge, split wedge, double disc parallels seats, double disc wedge, single disc single seat gate or slide, single disc parallel seats, plug gate valve.

What is lantern ring?

Description : What is lantern ring?

Last Answer : Answer: It’s a collection point to drain off any hazardous seepage or as a point where lubricant can be injected; it is in the middle of packing rings.

How to close a gate valve?

Description : How to close a gate valve?

Last Answer : Answer: Turn the hand-wheel in clockwise direction.

What are port types for gate valves?

Description : What are port types for gate valves?

Last Answer : Answer: Full port and reduced port. Default is reduced bore. Full port has to be specified in bom.

What is double disc globe valve?

Description : What is double disc globe valve?

Last Answer : Answer: Has two discs bearing on separate seats spaced apart, on a single shaft, for low torque, used for control valves.

Where WYE body globe valve is used?

Description : Where WYE body globe valve is used?

Last Answer : Answer: In line ports with stem emerging at 45 degree, for erosive fluids due to smoother flow pattern.

Where plug type disc globe valve is used?

Description : Where plug type disc globe valve is used?

Last Answer : Answer: For severe regulating service with gritty liquids such as boiler feedwater and for blow off service.

What are types of globe valve?

Description : What are types of globe valve?

Last Answer : Answer: Angle globe valve, plug type disc globe valve, WYE-body globe valve, composite disc globe valve, double disc globe valve.

What are characteristics of globe valve stem?

Description : What are characteristics of globe valve stem?

Last Answer : Answer: Always rising design, with disk nut at the lower end and handwheel at upper end.

What are globe valve disk types?

Description : What are globe valve disk types?

Last Answer : Answer: Flat faced type for positive shutoff, loose plug type for plug renewal or needle type for finer control.

What are globe valve port types?

Description : What are globe valve port types?

Last Answer : Answer: Full port: More than 85% of bore size, Reducer port: One size less than the connected pipe.

How to install a globe valve?

Description : How to install a globe valve?

Last Answer : Answer: Globe valve should be installed such that the flow is from the underside of the disk, Usually flow direction is marked on the globe valve.

What is needle valve?

Description : What is needle valve?

Last Answer : Answer: Full pyramid disc, same design as globe valve, smaller sizes, sw or threaded, flow control, disc can be integral with stem, inside screw, borged or barstock body and bonnet, manufacturers standard.

What is pinch valve?

Description : What is pinch valve?

Last Answer : Answer: Similar to diaphragm valve, with sleeves of rubber or PTFE, which get squeezed to control or stop the flow, Cast iron body, for very low service pressures like isolation of hose connections, manufacture standard.

What is dimensional standard for plug valve?

Description : What is dimensional standard for plug valve?

Last Answer : Answer: API 599.

What are eccentric plug valve?

Description : What are eccentric plug valve?

Last Answer : Answer: Off center plug, corrosive and abrasive service, on off action, moves into and away from seat eliminating abrasive wear.

What are permasil plug valve?

Description : What are permasil plug valve?

Last Answer : Answer: Plug valves with Teflon seat instead of sleeves, for on-off applications, can handle clean viscous and corrosive liquids, Graphite seat for high temperature applications. Drip tight shut off not possible.

What are Teflon sleeved plug valve?

Description : What are Teflon sleeved plug valve?

Last Answer : Answer: PTFE sleeve between plug and body of valve, low turning effort, minimum friction, temperature limitation, anti static design possible.

What is pressure balanced plug valve?

Description : What is pressure balanced plug valve?

Last Answer : Answer: With holes in port top and bottom connecting two chambers on top and bottom of plug, to reduce turning effort.

What are inverted plug design valve?

Description : What are inverted plug design valve?

Last Answer : Answer: Plug valve with taper portion up of plug. For 8” and higher size.

What are ventury pattern plug valve?

Description : What are ventury pattern plug valve?

Last Answer : Answer: Change of section through the body throat so graded to have ventury effect, minimum pressure loss.

What are short pattern plug valve?

Description : What are short pattern plug valve?

Last Answer : Answer: Valves with face to face dimension of gate valve, as a alternative to gate valve.

What is regular pattern plug valve?

Description : What is regular pattern plug valve?

Last Answer : Answer: Rectangular port, area almost equal to pipe bore, smooth transition from round body to rectangular port, for minimum pressure loss.

What are three patterns of plug valve design?

Description : What are three patterns of plug valve design?

Last Answer : Answer: Regular pattern, short pattern and ventury pattern.

What is metal seated lubricated plug valve?

Description : What is metal seated lubricated plug valve?

Last Answer : Answer: A plug valve with no plastic material, where grease is applied to contacting surfaces for easy operation.

What are uses of four way valve?

Description : What are uses of four way valve?

Last Answer : Answer: Reversal of pump suction and delivery, By pass of strainer or meter, reversal of flow through filter, heat exchanger or dryer.

What are the uses of three-way valve?

Description : What are the uses of three-way valve?

Last Answer : Answer: Alternate connection of the two supply lines to a common delivery vise versa, isolating one safety valve, division of flow with isolation facility.

What are types of flush bottom valves?

Description : What are types of flush bottom valves?

Last Answer : Answer: Valves with discs opening into the tank and valves with disks into the valve.

What are flush bottom valves?

Description : What are flush bottom valves?

Last Answer : Answer: Special type of valves used to drain out the piping, reactors and vessels, attached on pad type nozzles.

What is float valve?

Description : What is float valve?

Last Answer : Answer: Used to control liquid level in tanks, operated by float, which rises with liquid level and opens the valve to control water level. It can also remove air from system, in which case, air flows ... valve, float inside valve raises to close the valve and stop flow of water. Used in drip legs.

What is foot valve?

Description : What is foot valve?

Last Answer : Answer: Valve used to maintain a head of water on the suction side of sump pump, basically a lift check valve with integrated strainer.

What is safety valve?

Description : What is safety valve?

Last Answer : Answer: Rapid opening (popping action) full flow valve for air and other gases.

What is relief valve?

Description : What is relief valve?

Last Answer : Answer: Valve to relieve excess pressure in liquids in situations where full flow discharge is not required, when release of small volume of liquid would rapidly lower pressure.