The variable required to be known in correlations used for estimating the horse power of a centrifugal gas compressor and hence its cost is P. Inlet pressure Q. Compressor rpm R. Delivery pressure S. Volumetric flow rate at inlet. (A) P, Q and R (B) P and R (C) R and S (D) P, Rand S

The variable required to be known in correlations used for estimating
the horse power of a centrifugal gas compressor and hence its cost is
P. Inlet pressure
Q. Compressor rpm
R. Delivery pressure
S. Volumetric flow rate at inlet.
(A) P, Q and R
(B) P and R
(C) R and S
(D) P, Rand S
by

1 Answer

Answer :

(A) P, Q and R
by

Related questions

Horsepower increase of a centrifugal gas compressor without altering the volumetric flow rate will __________ the gas discharge pressure. (A) Increase (B) Decrease (C) Not change (D) Exponentially decrease

Description : Horsepower increase of a centrifugal gas compressor without altering the volumetric flow rate will __________ the gas discharge pressure. (A) Increase (B) Decrease (C) Not change (D) Exponentially decrease

Last Answer : (A) Increase

Conversion of dynamic velocity head into static pressure head in a centrifugal pump is the result of : (a) Increasing area of flow between adjacent vanes from inlet to outlet (b) Difference in pressure between suction and delivery ends (c) Radial thrust in pumps (d) Stuffing Box

Description : Conversion of dynamic velocity head into static pressure head in a centrifugal pump is the result of : (a) Increasing area of flow between adjacent vanes from inlet to outlet (b) Difference in pressure between suction and delivery ends (c) Radial thrust in pumps (d) Stuffing Box

Last Answer : (b) Difference in pressure between suction and delivery ends

A reciprocating compressor is not suitable for use as a supercharger because: A. it runs at lower rpm B. the pressure ratio is high C. volumetric efficiency is high D. it is bulky and can handle small quantity of air

Description : A reciprocating compressor is not suitable for use as a supercharger because: A. it runs at lower rpm B. the pressure ratio is high C. volumetric efficiency is high D. it is bulky and can handle small quantity of air

Last Answer : ANSWER : D

Which of the statement is “True” for centrifugal compressors? a) The compressor should not be operated at full load b) The compressor should be operated at shut off pressure c) The compressor should not be operated with inlet-guide vane control d) The compressor should not be operated close to the surge point

Description : Which of the statement is True for centrifugal compressors? a) The compressor should not be operated at full load b) The compressor should be operated at shut off pressure c) The ... operated with inlet-guide vane control d) The compressor should not be operated close to the surge point 

Last Answer : d) The compressor should not be operated close to the surge point

The peripheral velocity at inlet of a centrifugal pump having inlet diameter of 25 cms and rotating at 950 rpm is __________ m/sec. (A) 1.8 (B) 12.4 (C) 186.2 (D) 736.4

Description : The peripheral velocity at inlet of a centrifugal pump having inlet diameter of 25 cms and rotating at 950 rpm is __________ m/sec. (A) 1.8 (B) 12.4 (C) 186.2 (D) 736.4

Last Answer : (B) 12.4

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the power consumed now will be __________ hp. (A) 0.5 (B) 2 (C) 4 (D) 1

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the power consumed now will be __________ hp. (A) 0.5 (B) 2 (C) 4 (D) 1

Last Answer : (A) 0.5

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, then the new head will be __________ metres. (A) 2 (B) 4 (C) 8 (D) 5.5

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, then the new head will be __________ metres. (A) 2 (B) 4 (C) 8 (D) 5.5

Last Answer : (A) 2

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750

Last Answer : (A) 500

Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with decrease in pressure ratio C. It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Description : Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with ... It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Last Answer : ANSWER : A

Delivery of insufficient quantity of liquid by a pump may be caused by (A) Air leak in the inlet (B) Low rpm (C) Too high a lift (D) All (A), (B) and (C)

Description : Delivery of insufficient quantity of liquid by a pump may be caused by (A) Air leak in the inlet (B) Low rpm (C) Too high a lift (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which of the following can be used to create a flow of gas, where no significant compression is required? (A) Reciprocating compressor (B) Blower (C) Axial flow compressor (D) Centrifugal compressor

Description : Which of the following can be used to create a flow of gas, where no significant compression is required? (A) Reciprocating compressor (B) Blower (C) Axial flow compressor (D) Centrifugal compressor

Last Answer : (B) Blower

In centrifugal compressor terminology, vaneless space refers to the space between A. The inlet and blade inlet edge B. Blades in the impeller C. Diffuser exit and volute casing D. Impeller tip and diffuser inlet edge

Description : In centrifugal compressor terminology, vaneless space refers to the space between A. The inlet and blade inlet edge B. Blades in the impeller C. Diffuser exit and volute casing D. Impeller tip and diffuser inlet edge

Last Answer : ANSWER : D

Applying a pressure drop across a capillary results in a volumetric flow rate 'Q' under laminar flow conditions. The flow rate for the same pressure drop, in a capillary of the same length but half the radius is (A) Q/2 (B) Q/4 (C) Q/8 (D) Q/16

Description : Applying a pressure drop across a capillary results in a volumetric flow rate 'Q' under laminar flow conditions. The flow rate for the same pressure drop, in a capillary of the same length but half the radius is (A) Q/2 (B) Q/4 (C) Q/8 (D) Q/16

Last Answer : (D) Q/16

In centrifugal pump installation, (A) Pump is properly primed before starting (B) The diameter of the pipe at inlet as well as at outlet, is kept smaller than the delivery pipe (C) The motor may burn out if it is started with empty delivery pipe and with open gate valve (D) All the above

Description : In centrifugal pump installation,  (A) Pump is properly primed before starting  (B) The diameter of the pipe at inlet as well as at outlet, is kept smaller than the delivery pipe  (C) The ... out if it is started with empty delivery pipe and with open gate valve  (D) All the above 

Last Answer : (D) All the above 

The ratio of indicated power to shaft power of the engine required to drive the compressor is called A. Compressor efficiency B. Volumetric efficiency C. Isothermal efficiency D. Mechanical efficiency

Description : The ratio of indicated power to shaft power of the engine required to drive the compressor is called A. Compressor efficiency B. Volumetric efficiency C. Isothermal efficiency D. Mechanical efficiency

Last Answer : ANSWER : D

Which of the following parameters are not required for evaluating volumetric efficiency of the compressor? a) Power b) Cylinder bore diameter c) Stroke length d) FAD

Description : Which of the following parameters are not required for evaluating volumetric efficiency of the compressor? a) Power b) Cylinder bore diameter c) Stroke length d) FAD

Last Answer : a) Power

A large clearance volume in a reciprocating compressor results in A. Reduced volume flow rate B. Increased volume flow rate C. Lower suction pressure D. Lower delivery pressure

Description : A large clearance volume in a reciprocating compressor results in A. Reduced volume flow rate B. Increased volume flow rate C. Lower suction pressure D. Lower delivery pressure

Last Answer : ANSWER : A

A large clearance volume in reciprocating compressor results in A. reduced volume flow rate B. Increased volume flow rate C. Lower suction pressure D. Lower delivery pressure

Description : A large clearance volume in reciprocating compressor results in A. reduced volume flow rate B. Increased volume flow rate C. Lower suction pressure D. Lower delivery pressure

Last Answer : ANSWER : A

Define (i) I.P (ii) B.P (iii)Volumetric efficiency (iv)Isothermal efficiency of air compressor

Description : Define (i) I.P (ii) B.P (iii)Volumetric efficiency (iv)Isothermal efficiency of air compressor

Last Answer : i) I.P. - It is the ratio of polytrophic work into speed of compressor in revolution per second.   ii) B.P. - It is the power required to drive the compressor or power delivered to ... the ratio of isothermal power to the shaft power or brake power of motor required to drive the compressor  

The ratio of isothermal power to actual measured input power of a compressor is known as: a) Isothermal efficiency b) Volumetric Efficiency c) Barometric efficiency d) None

Description : The ratio of isothermal power to actual measured input power of a compressor is known as: a) Isothermal efficiency b) Volumetric Efficiency c) Barometric efficiency d) None 

Last Answer : a) Isothermal efficiency

With increase in compression ratio, the volumetric efficiency of air compressor (A) Increases (B) Decreases (C) Remain same (D) May increase or decrease (depends on the suction pressure)

Description : With increase in compression ratio, the volumetric efficiency of air compressor (A) Increases (B) Decreases (C) Remain same (D) May increase or decrease (depends on the suction pressure)

Last Answer : Option A

In a centrifugal compressor, an increase in speed at a given pressure ratio causes A. Increase in flow B. Decrease in flow C. Increase in efficiency D. Increase in flow and decrease in efficiency

Description : In a centrifugal compressor, an increase in speed at a given pressure ratio causes A. Increase in flow B. Decrease in flow C. Increase in efficiency D. Increase in flow and decrease in efficiency

Last Answer : ANSWER : D

In a centrifugal compressor an increase in speed at a given pressure ratio causes A. Increase in flow and increase in efficiency B. Increase in flow and decrease in efficiency C. Decrease in flow and increase in efficiency D. Decrease in flow and decrease in efficiency

Description : In a centrifugal compressor an increase in speed at a given pressure ratio causes A. Increase in flow and increase in efficiency B. Increase in flow and decrease in efficiency C. Decrease in flow and increase in efficiency D. Decrease in flow and decrease in efficiency

Last Answer : ANSWER : B

Why the work per kg of air flow in axial flow compressor is less compared to centrifugal compressor for same pressure ratio ?

Description : Why the work per kg of air flow in axial flow compressor is less compared to centrifugal compressor for same pressure ratio ?

Last Answer : Isentropic efficiency of axial flow compressor is higher.

In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) Discharge of water by a centrifugal pump being run at a constant rpm (B) Water flow in the suction and discharge pipe of a reciprocating pump (C) Water discharge from a vertical vessel in which constant level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump

In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Description : In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Last Answer : (A) Manometric

Cavitation in a centrifugal pump can be avoided by keeping the (A) Inlet pressure high (B) Outlet pressure low (C) Inlet pressure low (D) Outlet pressure high

Description : Cavitation in a centrifugal pump can be avoided by keeping the (A) Inlet pressure high (B) Outlet pressure low (C) Inlet pressure low (D) Outlet pressure high

Last Answer : (A) Inlet pressure high

Power required by a centrifugal pump is proportional to (where, D = diameter, N = r.p.m) (A) N2D3 (B) ND2 (C) N2D (D) N3D5

Description : Power required by a centrifugal pump is proportional to (where, D = diameter, N = r.p.m) (A) N2D3 (B) ND2 (C) N2D (D) N3D5

Last Answer : (D) N3D5

Which one of the following statements are correct for reciprocating air compressor? A. Its volumetric efficiency increases with increasing clearance ratio B. Its volumetric efficiency increases with pressure ratio C. Its volumetric efficiency does not vary with change in clearance ratio and pressure ratio D. Its volumetric efficiency decreases with increasing clearance ratio and pressure ratio

Description : Which one of the following statements are correct for reciprocating air compressor? A. Its volumetric efficiency increases with increasing clearance ratio B. Its volumetric efficiency increases ... ratio D. Its volumetric efficiency decreases with increasing clearance ratio and pressure ratio

Last Answer : ANSWER : D

In a fully turbulent flow (Re > 10 5 ) in a pipe of diameter 'd', for a constant pressure gradient, the dependence of volumetric flow rate of an incompressible fluid is (A) d(B) d2(C) d2.5(D) d

Description : In a fully turbulent flow (Re > 10 5 ) in a pipe of diameter 'd', for a constant pressure gradient, the dependence of volumetric flow rate of an incompressible fluid is (A) d (B) d 2 (C) d 2.5 (D) d

Last Answer : (C) d 2.5

For laminar flow of a shear thinning liquid in a pipe, if the volumetric flow rate is doubled, the pressure gradient will increase by a factor of (A) 2 (B) < 2 (C) > 2 (D) 1/2

Description : For laminar flow of a shear thinning liquid in a pipe, if the volumetric flow rate is doubled, the pressure gradient will increase by a factor of (A) 2 (B) < 2 (C) > 2 (D) 1/2

Last Answer : (A) 2

For every 4°C raise in air inlet temperature of an air compressor, the power consumption will increases by_____ a) 2% b) 1% c) 3% d) 4%

Description : For every 4°C raise in air inlet temperature of an air compressor, the power consumption will increases by_____ a) 2% b) 1% c) 3% d) 4%

Last Answer : b) 1%

To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length of the pipe is 1506 m and f = 0.01, ignoring other minor losses and assuming the economical diameter from Lea's formula D = 1.2 Q, the water horse power of the pump is (A) 400 (B) 450 (C) 500(D) 600

Description : To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is  installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length  of the ... the water horse power of the pump is  (A) 400  (B) 450  (C) 500 (D) 600

Last Answer : (D) 600

Interstage coolers are provided in a multistage compressor to (A) Save power in compressing a given volume to a given pressure (B) Cool the delivered air (C) Achieve the exact delivery pressure (D) None of these

Description : Interstage coolers are provided in a multistage compressor to (A) Save power in compressing a given volume to a given pressure (B) Cool the delivered air (C) Achieve the exact delivery pressure (D) None of these

Last Answer : (A) Save power in compressing a given volume to a given pressure

Differentiate between : (i) Reciprocating and rotary air compressor (ii) Centrifugal and axial flow compressor

Description : Differentiate between : (i) Reciprocating and rotary air compressor (ii) Centrifugal and axial flow compressor

Last Answer : (i) Reciprocating and rotary air compressor: Sr. No. Reciprocating air compressor  Rotary air compressor  1 It is having to and fro motion. It is having rotary ... I.C. engine and for refrigerants and industrial gases. Used universally with large gas turbine. 

Various efficiencies of a centrifugal pump are related as (where, ηm = mechanical efficiency ηv = volumetric efficiency. ηma = manometric efficiency ηo = overall efficiency) (A) ηma × ηm × ηv = ηo (B) ηm = ηv . ηma (C) ηma = ηm × ηv (D) ηv = ηm × ηma

Description : Various efficiencies of a centrifugal pump are related as (where, ηm = mechanical efficiency ηv = volumetric efficiency. ηma = manometric efficiency ηo = overall efficiency) (A) ηma × ηm × ηv = ηo (B) ηm = ηv . ηma (C) ηma = ηm × ηv (D) ηv = ηm × ηma

Last Answer : (B) ηm = ηv . ηma

In case of a, centrifugal pump, the ratio h1/h2is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller). (A) Mechanical (B) Overall (C) Volumetric (D) Impeller

Description : In case of a, centrifugal pump, the ratio h1/h2is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller). (A) Mechanical (B) Overall (C) Volumetric (D) Impeller

Last Answer : A) Mechanical

With increase in molecular weight of the gas, the head developed by a centrifugal compressor will (A) Decrease (B) Increase (C) Remain same (D) Unpredictable

Description : With increase in molecular weight of the gas, the head developed by a centrifugal compressor will (A) Decrease (B) Increase (C) Remain same (D) Unpredictable

Last Answer : (A) Decrease

The blades of a centrifugal impeller are said to be curved forward, if the __________ of the motion of impeller blades. (A) Inlet tip of a blade curves in a direction opposite to that (B) Outlet tip of a blade curves in a direction opposite to that (C) Inlet tip of a blade is towards the direction (D) Outlet tip of a blade is towards the direction

Description : The blades of a centrifugal impeller are said to be curved forward, if the __________ of the motion of impeller blades. (A) Inlet tip of a blade curves in a direction opposite to that (B) Outlet tip ... Inlet tip of a blade is towards the direction (D) Outlet tip of a blade is towards the direction

Last Answer : (D) Outlet tip of a blade is towards the direction

Which statement best describes a responsibility of the project manager: a. to be the sole source of expertise for estimating techniques on cost and time. b. to deliver the project objectives to enable benefits to be realised. c. to take ultimate accountability for the delivery of the business benefits. d. to delegate all accountability for managing time, cost and quality to team leaders.

Description : Which statement best describes a responsibility of the project manager: a. to be the sole source of expertise for estimating techniques on cost and time. b. to deliver the project objectives to ... benefits. d. to delegate all accountability for managing time, cost and quality to team leaders.

Last Answer : b. to deliver the project objectives to enable benefits to be realised.

Which statement best describes a responsibility of the project manager: a. to be the sole source of expertise for estimating techniques on cost and time. b. to deliver the project objectives to enable benefits to be realised. c. to take ultimate accountability for the delivery of the business benefits. d. to delegate all accountability for managing time, cost and quality to team leaders.

Description : Which statement best describes a responsibility of the project manager: a. to be the sole source of expertise for estimating techniques on cost and time.  b. to deliver the project objectives to ... benefits.  d. to delegate all accountability for managing time, cost and quality to team leaders.

Last Answer : b. to deliver the project objectives to enable benefits to be realised.

With suction pressure being atmospheric, increase in delivery pressure with fixed clearance volume A. increase volumetric efficiency B. decrease volumetric efficiency C. does not change volumetric efficiency D. First increase volumetric efficiency and then decrease it

Description : With suction pressure being atmospheric, increase in delivery pressure with fixed clearance volume A. increase volumetric efficiency B. decrease volumetric efficiency C. does not change volumetric efficiency D. First increase volumetric efficiency and then decrease it

Last Answer : ANSWER : B

How the net work to drive a compressor and its volumetric efficiency behave with increase in clearance volume ?

Description : How the net work to drive a compressor and its volumetric efficiency behave with increase in clearance volume ?

Last Answer : Work remains unaltered and volumetric efficiency decreases.

Reduction in the delivery pressure of a Compressor working at 7 bar, by 1 bar would reduce the power consumption by a) 6 to 10 % b) 2 to 3 % c) 12 to 14 % d) None of the above

Description : Reduction in the delivery pressure of a Compressor working at 7 bar, by 1 bar would reduce the power consumption by a) 6 to 10 % b) 2 to 3 % c) 12 to 14 % d) None of the above

Last Answer : a) 6 to 10 %

The clearance volume of the air compressor is kept minimum because A. It allows maximum compression to be achieved B. It greatly affects volumetric efficiency C. It results in minimum work D. It permits isothermal compression

Description : The clearance volume of the air compressor is kept minimum because A. It allows maximum compression to be achieved B. It greatly affects volumetric efficiency C. It results in minimum work D. It permits isothermal compression

Last Answer : ANSWER : B

Volumetric efficiency of air compressor is of the order of A. 20% to 30 % B. 40% to 50% C. 60% to 70% D. 70% to 90%

Description : Volumetric efficiency of air compressor is of the order of A. 20% to 30 % B. 40% to 50% C. 60% to 70% D. 70% to 90%

Last Answer : ANSWER : D