In centrifugal compressor terminology, vaneless space refers to the space between A. The inlet and blade inlet edge B. Blades in the impeller C. Diffuser exit and volute casing D. Impeller tip and diffuser inlet edge

In centrifugal compressor terminology, vaneless space refers to the space between A. The inlet and blade inlet edge B. Blades in the impeller C. Diffuser exit and volute casing D. Impeller tip and diffuser inlet edge  
by

1 Answer

Answer :

ANSWER : D
by
selected by

Related questions

Which one of the following statements is correct? A. Reciprocating compressors are used to supply large quantities of air at a lower pressure ratio B. Centrifugal compressors are used to supply large quantities of air at a lower pressure ratio C. Centrifugal compressors are used to supply small quantities of air at a lower pressure ratio D. Centrifugal compressors cannot be run at high speed because of impeller, diffuser and casing.

Description : Which one of the following statements is correct? A. Reciprocating compressors are used to supply large quantities of air at a lower pressure ratio B. Centrifugal compressors are used to supply ... . Centrifugal compressors cannot be run at high speed because of impeller, diffuser and casing.

Last Answer : ANSWER : B

The blades of a centrifugal impeller are said to be curved forward, if the __________ of the motion of impeller blades. (A) Inlet tip of a blade curves in a direction opposite to that (B) Outlet tip of a blade curves in a direction opposite to that (C) Inlet tip of a blade is towards the direction (D) Outlet tip of a blade is towards the direction

Description : The blades of a centrifugal impeller are said to be curved forward, if the __________ of the motion of impeller blades. (A) Inlet tip of a blade curves in a direction opposite to that (B) Outlet tip ... Inlet tip of a blade is towards the direction (D) Outlet tip of a blade is towards the direction

Last Answer : (D) Outlet tip of a blade is towards the direction

Centrifugal pump is normally classified on the basis of the (A) rpm (B) Type of casing (C) Impeller blade angle (D) Number of blades in impeller

Description : Centrifugal pump is normally classified on the basis of the (A) rpm (B) Type of casing (C) Impeller blade angle (D) Number of blades in impeller

Last Answer : (B) Type of casing

A centrifugal pump is called a turbine pump, if it is having a (A) Turbine type impeller (B) Vaned diffusion casing (C) Rotating vaned volute (D) None of these

Description : A centrifugal pump is called a turbine pump, if it is having a (A) Turbine type impeller (B) Vaned diffusion casing (C) Rotating vaned volute (D) None of these

Last Answer : (B) Vaned diffusion casing

Pick up the correct statement from the following regarding radial flow centrifugal pumps: (A) These are provided with volute type or turbine type casings (B) In involute type of radial flow centrifugal pump, the impeller discharges into a gradually expanding spiral casing (C) The efficiency of turbine type of radial flow centrifugal pump, is always higher than that of volute type (D) All the above

Description : Pick up the correct statement from the following regarding radial flow centrifugal pumps:  (A) These are provided with volute type or turbine type casings  (B) In involute type of radial flow ... centrifugal pump, is always higher than that of  volute type  (D) All the above 

Last Answer : (D) All the above 

Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid from the periphery of the impeller and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate

Description : Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid ... and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate

Last Answer : Option D

The pressure rise in the impeller of centrifugal compressor is achieved by A. the decrease in volume and diffusion action B. the centrifugal action and decrease in volume C. the centrifugal and diffusion action D. the centrifugal and push pull action

Description : The pressure rise in the impeller of centrifugal compressor is achieved by A. the decrease in volume and diffusion action B. the centrifugal action and decrease in volume C. the centrifugal and diffusion action D. the centrifugal and push pull action

Last Answer : ANSWER : D

Volute type of casing is provided in a centrifugal pump to (A) Convert velocity head to pressure head (B) Convert pressure head to velocity head (C) Reduce the discharge fluctuation (D) Increase the discharge

Description : Volute type of casing is provided in a centrifugal pump to (A) Convert velocity head to pressure head (B) Convert pressure head to velocity head (C) Reduce the discharge fluctuation (D) Increase the discharge

Last Answer : (D) Increase the discharge

Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes in the impeller (C) Mounting of two or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Description : Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes ... or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Last Answer : (C) Mounting of two or more impellers in series on a single shaft

Which one of the following types of impeller vanes are most commonly used in centrifugal type compressors? A. Forward curved B. Radial C. Backward curved D. Tangential

Description : Which one of the following types of impeller vanes are most commonly used in centrifugal type compressors? A. Forward curved B. Radial C. Backward curved D. Tangential

Last Answer : ANSWER : C

Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these

Description : Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these

Last Answer : (B) Loss of kinetic head

The power required to drive a turbo compressor for a given pressure ratio decreases when A. Air is heated at entry B. Air is cooled at entry C. Air is cooled at exit D. Air is heated at exit

Description : The power required to drive a turbo compressor for a given pressure ratio decreases when A. Air is heated at entry B. Air is cooled at entry C. Air is cooled at exit D. Air is heated at exit

Last Answer : ANSWER : B

The domestic refrigerator uses following type of compressor (a) centrifugal (b) axial (c) miniature sealed unit (d) piston type reciprocating

Description : The domestic refrigerator uses following type of compressor (a) centrifugal (b) axial (c) miniature sealed unit (d) piston type reciprocating

Last Answer : Ans: d

In a centrifugal compressor, an increase in speed at a given pressure ratio causes A. Increase in flow B. Decrease in flow C. Increase in efficiency D. Increase in flow and decrease in efficiency

Description : In a centrifugal compressor, an increase in speed at a given pressure ratio causes A. Increase in flow B. Decrease in flow C. Increase in efficiency D. Increase in flow and decrease in efficiency

Last Answer : ANSWER : D

The specific speed of a centrifugal compressor is generally A. less than that of reciprocating compressor B. independent of compressor type, but depends only on size of compressor C. higher than that of axial compressor D. more than specific speed of reciprocating compressor but less than axial compressor

Description : The specific speed of a centrifugal compressor is generally A. less than that of reciprocating compressor B. independent of compressor type, but depends only on size of compressor C. higher ... axial compressor D. more than specific speed of reciprocating compressor but less than axial compressor

Last Answer : ANSWER : C

In a centrifugal compressor an increase in speed at a given pressure ratio causes A. Increase in flow and increase in efficiency B. Increase in flow and decrease in efficiency C. Decrease in flow and increase in efficiency D. Decrease in flow and decrease in efficiency

Description : In a centrifugal compressor an increase in speed at a given pressure ratio causes A. Increase in flow and increase in efficiency B. Increase in flow and decrease in efficiency C. Decrease in flow and increase in efficiency D. Decrease in flow and decrease in efficiency

Last Answer : ANSWER : B

The head developed by a centrifugal pump is largely determined by the (A) Power of the pump(B) Nature of the liquid being pumped(C) Angle of the vanes and the speed of the tip of the impeller(D) Vapour pressure of the liquid

Description : The head developed by a centrifugal pump is largely determined by the (A) Power of the pump (B) Nature of the liquid being pumped (C) Angle of the vanes and the speed of the tip of the impeller (D) Vapour pressure of the liquid

Last Answer : (C) Angle of the vanes and the speed of the tip of the impeller

The variable required to be known in correlations used for estimating the horse power of a centrifugal gas compressor and hence its cost is P. Inlet pressure Q. Compressor rpm R. Delivery pressure S. Volumetric flow rate at inlet. (A) P, Q and R (B) P and R (C) R and S (D) P, Rand S

Description : The variable required to be known in correlations used for estimating the horse power of a centrifugal gas compressor and hence its cost is P. Inlet pressure Q. Compressor rpm R. Delivery pressure S. Volumetric flow rate at inlet. (A) P, Q and R (B) P and R (C) R and S (D) P, Rand S

Last Answer : (A) P, Q and R

Which of the statement is “True” for centrifugal compressors? a) The compressor should not be operated at full load b) The compressor should be operated at shut off pressure c) The compressor should not be operated with inlet-guide vane control d) The compressor should not be operated close to the surge point

Description : Which of the statement is True for centrifugal compressors? a) The compressor should not be operated at full load b) The compressor should be operated at shut off pressure c) The ... operated with inlet-guide vane control d) The compressor should not be operated close to the surge point 

Last Answer : d) The compressor should not be operated close to the surge point

The size of inlet valve of an engine in comparison to exhaust valve is A. more B. less C. same D. varies from design to design

Description : The size of inlet valve of an engine in comparison to exhaust valve is A. more B. less C. same D. varies from design to design

Last Answer : ANSWER : B

In a typical medium speed 4- stroke Diesel engine, the inlet valve A. opens 20°before top dead centre and closes at 35°afterthebottomdead centre. B. opens up at top dead centre and closes at bottomdead centre C. may open orcloseanywhere D. remains open for 200°

Description : In a typical medium speed 4- stroke Diesel engine, the inlet valve A. opens 20°before top dead centre and closes at 35°afterthebottomdead centre. B. opens up at top dead centre and closes at bottomdead centre C. may open orcloseanywhere D. remains open for 200°

Last Answer : ANSWER : A

The _____________ sensor, checks the temperature of the ambient air entering the engine for fine tuning the mixture strength. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Description : The _____________ sensor, checks the temperature of the ambient air entering the engine for fine tuning the mixture strength. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Last Answer : Answer: d Explanation: The air inlet temperature sensor, checks the temperature of the ambient air entering the engine for fine tuning the mixture strength whereas the engine temperature sensor senses the ... gas senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio.

The _____________ sensor, monitors mass or volume of air flowing into the intake manifold for adjusting the quantity of fuel. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Description : The _____________ sensor, monitors mass or volume of air flowing into the intake manifold for adjusting the quantity of fuel. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Last Answer : Answer: c Explanation: The air flow sensor, monitors mass or volume of air flowing into the intake manifold for adjusting the quantity of fuel while exhaust gas senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio.

The _____________ sensor senses the temperature of the engine coolant, and from this data the computer adjusts the mixture strength to rich side for cold starting. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Description : The _____________ sensor senses the temperature of the engine coolant, and from this data the computer adjusts the mixture strength to rich side for cold starting. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Last Answer : Answer: a Explanation: The engine temperature sensor senses the temperature of the engine coolant, and from this data the computer adjusts the mixture strength to rich side for cold starting while the ... gas senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio.

In _____________ sensor, output voltage changes in proportion to air-fuel ratio. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Description : In _____________ sensor, output voltage changes in proportion to air-fuel ratio. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Last Answer : Answer: b Explanation: Only in exhaust gas sensor, output voltage changes in proportion to air-fuel ratio.

_____________ senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio. a) Engine temperature b) Exhaust gas c) Air flow d) Air inlet temperature

Description : _____________ senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio. a) Engine temperature b) Exhaust gas c) Air flow d) Air inlet temperature

Last Answer : Answer: b Explanation: Exhaust gas senor senses the amount of oxygen in the engine exhaust and calculates airfuel ratio while engine temperature sensor senses the temperature of the engine coolant, and from this data the computer adjusts the mixture strength to rich side for cold starting.

The knocking tendency in CI engines increases with (a) Increase of coolant water temperature (b) Increase of temperature of inlet air (c) Decrease of compression ratio (d) Increase of compression ratio

Description : The knocking tendency in CI engines increases with (a) Increase of coolant water temperature (b) Increase of temperature of inlet air (c) Decrease of compression ratio (d) Increase of compression ratio

Last Answer : Ans :c

In SI engines knocking can be reduced by (a) Increasing the compression ratio (b) Increasing the cooling water temperature (c) Retarding the spark advance (d) Increasing the inlet air temperature

Description : In SI engines knocking can be reduced by (a) Increasing the compression ratio (b) Increasing the cooling water temperature (c) Retarding the spark advance (d) Increasing the inlet air temperature

Last Answer : Ans :c

Mixing of air and fuel in the diesel engine occurs in a. injection pump b. carburetor c. engine cylinder d. inlet manifold

Description : Mixing of air and fuel in the diesel engine occurs in a. injection pump b. carburetor c. engine cylinder d. inlet manifold

Last Answer : ANSWER c. engine cylinder

Differentiate induced draft and forced draft cooling towers based on (i) Location of fan (ii) Corrosion of blades (iii) Efficiency (iv) Fan size

Description : Differentiate induced draft and forced draft cooling towers based on (i) Location of fan (ii) Corrosion of blades (iii) Efficiency (iv) Fan size

Last Answer : Differentiate induced draft and forced draft cooling towers based on (i) Location of fan (ii) Corrosion of blades (iii) Efficiency (iv) Fan size

A compressor that takes suction at a pressure below atmospheric and discharge against atmospheric pressure is called a __________ pump. (A) Sump (B) Volute (C) Vacuum (D) Submerged

Description : A compressor that takes suction at a pressure below atmospheric and discharge against atmospheric pressure is called a __________ pump. (A) Sump (B) Volute (C) Vacuum (D) Submerged

Last Answer : (C) Vacuum

The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute

Description : The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute

Last Answer : (A) Electromagnetic

Maintenance cost of a __________ pump for a particular duty is the least. (A) Centrifugal (B) Reciprocating (C) Volute (D) Gear

Description : Maintenance cost of a __________ pump for a particular duty is the least. (A) Centrifugal (B) Reciprocating (C) Volute (D) Gear

Last Answer : (A) Centrifugal

Volute of a centrifugal pump should be designed in a fashion, such that the (A) Kinetic head gets converted into static head (B) Moving stream gradually reduces velocity (C) Mean velocity remains constant (D) None of these

Description : Volute of a centrifugal pump should be designed in a fashion, such that the (A) Kinetic head gets converted into static head (B) Moving stream gradually reduces velocity (C) Mean velocity remains constant (D) None of these

Last Answer : (A) Kinetic head gets converted into static head

To handle smaller quantity of fluid at higher discharge pressure, use a __________ pump. (A) Reciprocating (B) Centrifugal (C) Volute (D) Rotary vacuum

Description : To handle smaller quantity of fluid at higher discharge pressure, use a __________ pump. (A) Reciprocating (B) Centrifugal (C) Volute (D) Rotary vacuum

Last Answer : (A) Reciprocating

Draining of shallow pits or sump is done by a sump pump, which is a __________ pump. (A) Single stage vertical (B) Centrifugal (C) Plunger (D) Diffuser

Description : Draining of shallow pits or sump is done by a sump pump, which is a __________ pump. (A) Single stage vertical (B) Centrifugal (C) Plunger (D) Diffuser

Last Answer : (A) Single stage vertical

Classification of air compressor

Description : Classification Of Air Compressor

Last Answer : Air compressors are classified in several different ways, depending on the specific characteristics and features of the compressor. Here are a few common ways that air compressors are classified: ... range of sizes and capacities, from small, portable units to large, industrial-sized compressors.

Reducing suction pressure in refrigeration cycle (a) lowers evaporation temperature (b) increases power required per ton of refrigeration (c) lowers compressor capacity because vapour is lighter (d) all of the above.

Description : Reducing suction pressure in refrigeration cycle (a) lowers evaporation temperature (b) increases power required per ton of refrigeration (c) lowers compressor capacity because vapour is lighter (d) all of the above.

Last Answer : Ans: d

The coefficient of performance is the ratio of the refrigerant effect to the (a) heat of compression (b) work done by compressor (c) enthalpy increase in compressor (d) all of the above

Description : The coefficient of performance is the ratio of the refrigerant effect to the (a) heat of compression (b) work done by compressor (c) enthalpy increase in compressor (d) all of the above

Last Answer : Ans: d

For obtaining high COP, the pressure range of compressor should be (a) high (b) low (c) optimum (d) any value

Description : For obtaining high COP, the pressure range of compressor should be (a) high (b) low (c) optimum (d) any value

Last Answer : Ans: b

The suction pipe diameter of refrigerating unit compressor in comparison to delivery side is (a) bigger (b) smaller (c) equal (d) smaller/bigger depending on capacity

Description : The suction pipe diameter of refrigerating unit compressor in comparison to delivery side is (a) bigger (b) smaller (c) equal (d) smaller/bigger depending on capacity

Last Answer : Ans: a

In vapour compression cycle using NH3 as refrigerant, initial charge is filled at (a) suction of compressor (b) delivery of compressor (c) high pressure side close to receiver (d) low pressure side near receiver

Description : In vapour compression cycle using NH3 as refrigerant, initial charge is filled at (a) suction of compressor (b) delivery of compressor (c) high pressure side close to receiver (d) low pressure side near receiver

Last Answer : Ans: c

Where does the lowest temperature occur in a vapour compression cycle ? (a) condenser (b) evaporator (c) compressor (d) expansion valve

Description : Where does the lowest temperature occur in a vapour compression cycle ? (a) condenser (b) evaporator (c) compressor (d) expansion valve

Last Answer : Ans: b

In a refrigeration cycle, the flow of refrigerant is controlled by (a) compressor (b) condenser (c) evaporator (d) expansion valve

Description : In a refrigeration cycle, the flow of refrigerant is controlled by (a) compressor (b) condenser (c) evaporator (d) expansion valve

Last Answer : Ans: d

In vapour compression refrigeration system, refrigerant occurs as liquid between (a) condenser and expansion valve (b) compressor and evaporator (c) expansion valve and evaporator (d) compressor and condenser

Description : In vapour compression refrigeration system, refrigerant occurs as liquid between (a) condenser and expansion valve (b) compressor and evaporator (c) expansion valve and evaporator (d) compressor and condenser

Last Answer : Ans: c

In a flooded evaporator refrigerator, an accumulator at suction of compressor is used to (a) collect liquid refrigerant and prevent it from going to compressor (b) detect liquid in vapour (c) superheat the vapour (d) increase refrigeration effect

Description : In a flooded evaporator refrigerator, an accumulator at suction of compressor is used to (a) collect liquid refrigerant and prevent it from going to compressor (b) detect liquid in vapour (c) superheat the vapour (d) increase refrigeration effect

Last Answer : Ans: a

Formation of frost on evaporator in refrigerator (a) results in loss of heat due to poor heat transfer (b) increases heat transfer rate (c) decreases compressor power. (d) can be avoided by proper design

Description : Formation of frost on evaporator in refrigerator (a) results in loss of heat due to poor heat transfer (b) increases heat transfer rate (c) decreases compressor power. (d) can be avoided by proper design

Last Answer : Ans: a

One of the purposes of sub-cooling the liquid refrigerant is to (a) reduce compressor overheating (b) reduce compressor discharge temperature (c) increase cooling effect (d) ensure that only liquid and not the vapour enters the expansion (throttling) valve

Description : One of the purposes of sub-cooling the liquid refrigerant is to (a) reduce compressor overheating (b) reduce compressor discharge temperature (c) increase cooling effect (d) ensure that only liquid and not the vapour enters the expansion (throttling) valve

Last Answer : Ans: d

The higher temperature in vapour compression cycle occurs at (a) compressor discharge. (b) expansion valve (c) evaporator (d) condenser discharge

Description : The higher temperature in vapour compression cycle occurs at (a) compressor discharge. (b) expansion valve (c) evaporator (d) condenser discharge

Last Answer : Ans: a

Presence of moisture in a refrigerant affects the working of (a) compressor (b) condenser (c) evaparator (d) expansion valve.

Description : Presence of moisture in a refrigerant affects the working of (a) compressor (b) condenser (c) evaparator (d) expansion valve.

Last Answer : Ans: a