How many characters per sec (7 bits + 1 parity ) can be transmitted over a 2400 bps line if the transfer is synchronous (1 start and 1 stop bit)?

How many characters per sec (7 bits + 1 parity ) can be transmitted over a 2400 bps line if the transfer is synchronous (1 start and 1 stop bit)?
by

1 Answer

Answer :

1. 300 2. 240
3. 250 4. 275
Ans- 2400/(7+1+2) 240
by

Related questions

How many characters per sec (7 bits + 1 parity) can be transmitted over a 2400 bps line if the transfer is ...

Description : How many characters per sec (7 bits + 1 parity) can be transmitted over a 2400 bps line if the transfer is synchronous (1 start bit and 1 stop bit)?  A) 300 B) 240 C) 250 D) 275

Last Answer : How many characters per sec (7 bits + 1 parity) can be transmitted over a 2400 bps line if the transfer is synchronous (1 start bit and 1 stop bit)?  300

How many 8-bit characters can be transmitted per second over a 9600 baud serial communication link using asynchronous mode of transmission with one start bit, eight data bits, two stop bits, and one parity bit ? a. 600 b. 800 c. 876 d. 1200

Description : How many 8-bit characters can be transmitted per second over a 9600 baud serial communication link using asynchronous mode of transmission with one start bit, eight data bits, two stop bits, and one parity bit ? a. 600 b. 800 c. 876 d. 1200

Last Answer : b. 800

An analog signal carries 4 bits in each signal unit. If 1000 signal units are sent per second, then baud rate and bit rate of the signal are ............... and .............. (A) 4000 bauds \ sec & 1000 bps (B) 2000 bauds \ sec & 1000 bps (C) 1000 bauds \ sec & 500 bps (D) 1000 bauds \ sec & 4000 bps

Description : An analog signal carries 4 bits in each signal unit. If 1000 signal units are sent per second, then baud rate and bit rate of the signal are ............... and .............. (A) 4000 bauds \ sec & ... (B) 2000 bauds \ sec & 1000 bps (C) 1000 bauds \ sec & 500 bps (D) 1000 bauds \ sec & 4000 bps

Last Answer : (D) 1000 bauds \ sec & 4000 bps Explanation: Bit rate is the number of bits per second. Baud rate is the number of signal units per second. Baud rate is less than or equal to the bit rate. Baud rate = 1000 bauds per second (baud/s) Bit rate = 1000 x 4 = 4000 bps

ECE Board Exam March 1996 What is the transmission rate of a system for transmitting the output of a microcomputer to a line printer operating at a speed of 30 lines/minute? Assume that the line printer has 8 bits of data per character and prints out 80 characters/line. A. 800 bps B. 400 bps C. 320 bps D. 640 bps

Description : ECE Board Exam March 1996 What is the transmission rate of a system for transmitting the output of a microcomputer to a line printer operating at a speed of 30 lines/minute? Assume that the line printer has 8 bits ... and prints out 80 characters/line. A. 800 bps B. 400 bps C. 320 bps D. 640 bps

Last Answer : C. 320 bps

Assuming 8 bits for data, 1 bit for parity, I start bit and 2 stop bits, ...

Description : Assuming 8 bits for data, 1 bit for parity, I start bit and 2 stop bits, the number of characters that 1200 BPS communication line can transmit is

Last Answer : Assuming 8 bits for data, 1 bit for parity, I start bit and 2 stop bits, the number of characters that 1200 BPS communication line can transmit is 12CPS.

What are the main advantages of synchronous circuit?

Description : What are the main advantages of synchronous circuit?

Last Answer : Ans-All the inputs are feed at the rising or falling end of the clock signal. This makes the circuit to perform task in sync. so that the functional integrity of the logic device is as expected.

In______ transmission, wesend1 start bit (0) at thebeginningand 1 or more stop bits (1s) at the end of each byte. A) synchronous B) asynchronous C) isochronous D) none of the above

Description : In______ transmission, wesend1 start bit (0) at thebeginningand 1 or more stop bits (1s) at the end of each byte. A) synchronous B) asynchronous C) isochronous D) none of the above

Last Answer : asynchronous

Cost of storing a bit is minimum in 1. Cache 2. Register 3. RAM 4. Magnetic tape

Description : Cost of storing a bit is minimum in 1. Cache 2. Register 3. RAM 4. Magnetic tape

Last Answer : Ans-Magnetic Tape

Usually, it takes10-bits to represent one character. How many characters can betransmittedat a speed of 1200 BPS? A. 10 B. 12 C. 120 D. 1200 E. None of the above

Description : Usually, it takes10-bits to represent one character. How many characters can betransmittedat a speed of 1200 BPS? A. 10 B. 12 C. 120 D. 1200 E. None of the above

Last Answer : 120

An analog signal has a bit rate of 6000 bps and a baud rate of 2000 baud. How many data elements are carried by each signal element ? (A) 0.336 bits/baud (B) 3 bits/baud (C) 120,00,000 bits/baud (D) None of the above

Description : An analog signal has a bit rate of 6000 bps and a baud rate of 2000 baud. How many data elements are carried by each signal element ? (A) 0.336 bits/baud (B) 3 bits/baud (C) 120,00,000 bits/baud (D) None of the above

Last Answer : (B) 3 bits/baud

Assume that we need to download text documents at the rate of 100 pages per minute. A page is an average of 24 lines with 80 characters in each line and each character requires 8 bits. Then the required bit rate of the channel is ................ (A) 1.636 Kbps (B) 1.636 Mbps (C) 2.272 Mbps (D) 3.272 Kbps

Description : Assume that we need to download text documents at the rate of 100 pages per minute. A page is an average of 24 lines with 80 characters in each line and each character requires 8 bits. Then the required bit rate of the channel is ... ...... (A) 1.636 Kbps (B) 1.636 Mbps (C) 2.272 Mbps (D) 3.272 Kbps

Last Answer : Answer: Marks given to all

Each check bit is grouped with the information bits as specified by a__ a. Parity check code b. Parity check matrix c. Parity check bit d. All of these

Description : Each check bit is grouped with the information bits as specified by a__ a. Parity check code b. Parity check matrix c. Parity check bit d. All of these

Last Answer : b. Parity check matrix

Given code word 1110001010 is to be transmitted with even parity check bit. The encoded word to be transmitted for this code is (A) 11100010101 (B) 11100010100 (C) 1110001010 (D) 111000101

Description : Given code word 1110001010 is to be transmitted with even parity check bit. The encoded word to be transmitted for this code is (A) 11100010101 (B) 11100010100 (C) 1110001010 (D) 111000101

Last Answer : (A) 11100010101 

Iridium satellites can provide data communications of up ____ bps data rate. A. 1200 B. 4800 C. 2400 D. 3840

Description : Iridium satellites can provide data communications of up ____ bps data rate. A. 1200 B. 4800 C. 2400 D. 3840

Last Answer : C. 2400

What arethe most commonly used transmission speeds in BPS usedin datacommunication? A. 300 B. 1200 C. 2400 D. 9600 E. None of the above

Description : What arethe most commonly used transmission speeds in BPS usedin datacommunication? A. 300 B. 1200 C. 2400 D. 9600 E. None of the above

Last Answer : 9600

How many bytes of data can be sent in 15 seconds over a serial link with baud rate of 9600 in asynchronous mode with odd parity and two stop bits in the frame? a. 10,000 bytes b. 12,000 bytes c. 15,000 bytes d. 27,000 bytes

Description : How many bytes of data can be sent in 15 seconds over a serial link with baud rate of 9600 in asynchronous mode with odd parity and two stop bits in the frame? a. 10,000 bytes b. 12,000 bytes c. 15,000 bytes d. 27,000 bytes

Last Answer : b. 12,000 bytes

Design a digital circuit which has one input two output and one select line input should be 1000khz output should be 500khz and 250Khz select line either 0 or 1 if 0 select 250khz if 1 select 500khz

Description : Design a digital circuit which has one input two output and one select line input should be 1000khz output should be 500khz and 250Khz select line either 0 or 1 if 0 select 250khz if 1 select 500khz

Last Answer : Ans-demux is the circuit which satisfies the given requirement if 0 is given to the selectline 250khz o/p is provided else 500khz o/p is provided.

If delaysare recorded as 10 bit numbers in a 50 router network, and delay vectorsare exchanged twicea second,how muchbandwidth per fill duplex line is occupied by the distributedrouting algorithm? A. 500 bps B. 1500 bps C. 5 bps D. 1000 bps

Description : If delaysare recorded as 10 bit numbers in a 50 router network, and delay vectorsare exchanged twicea second,how muchbandwidth per fill duplex line is occupied by the distributedrouting algorithm? A. 500 bps B. 1500 bps C. 5 bps D. 1000 bps

Last Answer : 1000 bps

In a digital transmission, the receiver clock is 0.1 percent faster than the sender clock. How many extra bits per second does the receiver receive if the data rate is 1 Mbps ? (A) 10 bps (B) 100 bps (C) 1000 bps (D) 10000 bps

Description : In a digital transmission, the receiver clock is 0.1 percent faster than the sender clock. How many extra bits per second does the receiver receive if the data rate is 1 Mbps ? (A) 10 bps (B) 100 bps (C) 1000 bps (D) 10000 bps

Last Answer : (C) 1000 bps 

The synchronous modems are more costly than the asynchronous modems because a. they produce large volume of data b. they contain clock recovery circuits c. they transmit the data with stop and start bits d. they operate with a larger bandwidth e. none of above

Description : The synchronous modems are more costly than the asynchronous modems because a. they produce large volume of data b. they contain clock recovery circuits c. they transmit the data with stop and start bits d. they operate with a larger bandwidth e. none of above

Last Answer : they contain clock recovery circuits

The synchronous modems are more costly than the asynchronous modemsbecause A. they produce largevolumeof data B. they contain clock recovery circuits C. they transmit thedata with stop and start bits. D. they operate witha largerbandwidth E. None of the above

Description : The synchronous modems are more costly than the asynchronous modemsbecause A. they produce largevolumeof data B. they contain clock recovery circuits C. they transmit thedata with stop and start bits. D. they operate witha largerbandwidth E. None of the above

Last Answer : they contain clock recovery circuits

What is Biasing?

Description : What is Biasing?

Last Answer : Ans- Biasing is process of applying potential across any electronic equipment in order to make it operate as we require.

what is the main application of scr in electronic field as well as in software field?

Description : what is the main application of scr in electronic field as well as in software field?

Last Answer : Ans- SCR is a rectifier we use this in power handling applications . By varying on time and off time of the scr i.e by giving the pulse to its gate we can vary the average output power ... part we can use micro controller and write a programme so that to generate required pulses to control the SCR.

what is fixed bias with and without decoupling capacitor

Description : what is fixed bias with and without decoupling capacitor

Last Answer : Ans- with ta decoupling capacitor u cannt get o/p bcz it blocks the DC and allows only AC ok.... is u dont us it it give the o/p but it's DC only so no use to hav a DC voltage in O/P

what is selective flooding?

Description : what is selective flooding?

Last Answer : Ans- Selective Flooding is a method to compute the Qos of the system

what is angle and amplitude modulation? what is noise in modulation?

Description : what is angle and amplitude modulation? what is noise in modulation?

Last Answer : Ans- modulation means change. to send a message of low frequency to a far distance we use a carrier of high frequency to carry the message. while transfering we change some parameters of ... is an unwanted signal which enter in signal while transfering a signal and makes the signal distorted.

Do we have any negative frequency?

Description : Do we have any negative frequency?

Last Answer : Ans-no it can't be negative because frequency is simply the reciprocal of time and time can't be negative. We use negative frequencies in our calculations just for easieness but remember at last we neglect it also

why the feeding frequency to a microprocessor s twice the operating frequency.

Description : why the feeding frequency to a microprocessor s twice the operating frequency.

Last Answer : Ans-since 8085 microprocessor operating frequency 5 mega hz but operating frequency is 10 mega hz because crystal effect in processor

What is the difference between PLC and DCS?

Description : What is the difference between PLC and DCS?

Last Answer : Ans-PLC means Programmable Logic Controller, which can be used to control one particular control system such as a boiler or a injection system. but DCS is Distributed control syetem, which is used ... the total process plant. in DCS we have no of controllers connected to a single monitoring system.

What does CE mean..U will see it on almost every chip(IC)..

Description : What does CE mean..U will see it on almost every chip(IC)..

Last Answer : Ans-The CE mark is a mandatory European marking for certain product groups to indicate conformity with the essential health and safety requirements set out in European Directives. The ... is certified by following clear and understandable procedures, the socalled conformity assessment procedures'

Which one is faster between NAND-SR FF and NOR-SR FF?

Description : Which one is faster between NAND-SR FF and NOR-SR FF?

Last Answer : Ans-well both deals with same principle.but i think NAND-SR FF is faster than NOR-SR FF

what is meant by virtual ground in the op amp ?

Description : what is meant by virtual ground in the op amp ?

Last Answer : Ans-The op amp connected in a negative feedback configuration that is the o/p connected to the inverting terminal tried to produce the same voltage at the inverting node as we applied to ... the inverting node at the ground potential and whatever the difference between these two nodes are amplified.

Why the input impedance of OP-Amp is so high?

Description : Why the input impedance of OP-Amp is so high?

Last Answer : Ans-In OPAMP we have 4 stages 1st stage i.e the input stage is a dual i/p balanced o/p opamp whose i/p resistance is v high. and if we use FET in case of BJT for 1st stage diffamp then i/p resistance will be v high in M ohms.

What is Virtual Grounding?

Description : What is Virtual Grounding?

Last Answer : Ans-Virtual grounding is the shorting of the inverting and the non-inverting terminals of the op-amp. The i/p resistance of opamp is v high. thus the base currents are v less approx 0. thus ... is same. thus if NOW one terminal is grounded due to virtual short other terminal also will be grounded.

What CMOS Transistor?

Description : What CMOS Transistor?

Last Answer : Ans-CMOS-->>Complementary Metal Oxide Semiconductor Complementary metal-oxide-semiconductor (CMOS) is a major class of integrated circuits. CMOS technology is used in chips such as microprocessors ... CMOS transistor as announced by IBM and Intel for the 45 nanometer node and beyond

What are digital elctronic flip flops, State the different types of flip flop and their uses.

Description : What are digital elctronic flip flops, State the different types of flip flop and their uses.

Last Answer : Ans-digital electronic flip flops are temporary single bit storage devices.different types of flip flops are JK f/f RS f/f T F/F D f/f this flip flops are using as storage device delay purpose as counter for toggled as shift register etc

What is a sequential circuit and What is a combinational circuit?Is there any difference between them? If yes what is it?

Description : What is a sequential circuit and What is a combinational circuit?Is there any difference between them? If yes what is it?

Last Answer : Ans-Combinational circuit are those whose output depends only upon the present inputs but in sequential circuit the output depends upon both present and past inputs. that is the difference.

How microprocessor works without internal memory?

Description : How microprocessor works without internal memory?

Last Answer : Ans-microprocessor works without internal memory because it consists of adreess data and control buses with some registers to process the task given to processor through the external memory.

What is Interfacing?

Description : What is Interfacing?

Last Answer : Ans-The peripheral (simple input/output devices ) connected with computer to perform tasks is known as interfacing.

Why the shape of OP-AMP is triangular not other shape?

Description : Why the shape of OP-AMP is triangular not other shape?

Last Answer : Ans-The Triangular shape symbolizes that it works for continous signals and hence forth it is an analog device. ex: Opamp If it is square then it is digital device. ex: Multiplexer If the shape is both triangular and square then it is mixed signal device. ex: ADC DAC

How many type of resistor are there in diode?

Description : How many type of resistor are there in diode?

Last Answer : Ans-They are two types one is forward resistance 1.Forward resistance 2.Reverse resistance 1.Forward resistance-This is the resistance offered in forward bias condition of the diode. It is calculated by ... in the reverse bias condition of the diode. It is also calculated by the same method.

What is Pulse Width Modulation?

Description : What is Pulse Width Modulation?

Last Answer : Ans-Pulse width modulation is a modulation technique in which the width of the pulse is varied in accordance with the message signal. Pulse width Modulation is abbreviated as PWM. PWM can be used ... the pulse train and recover an average analog waveform. PWM is used in sound synthesis circuits.

Why the input resistance of an ideal OPAMP is infinite and output resistance is zero? secondly, how can we measure these resistances(input and output) in case of an ideal OPAMPand Real OP-AMP in the following conditions when 1- load is not connected. 2- load is connected.

Description : Why the input resistance of an ideal OPAMP is infinite and output resistance is zero? secondly, how can we measure these resistances(input and output) in case of an ideal OPAMPand Real OP-AMP in the following conditions when 1- load is not connected. 2- load is connected.

Last Answer : Ans- Ideal OP-AMP is a power ful concept. If one goes through the history of amplifying devices it becomes clear that less it loads the previous stage better the output signal. ie ... . Can refer application notes by device manufacturer available in internet for more precise and practical solutions.

What are semiconductor devices ?

Description : What are semiconductor devices ?

Last Answer : Ans-Semiconductor Devices is nothing but a device which conduct semi /partially conducting ( semiconductor which conduction property lies between conductor and insulator)is termed as semiconductor device.

how to design a software IC using VHDL ?

Description : how to design a software IC using VHDL ?

Last Answer : Ans-you can use software like altera write the required programme download to the chip here is your software ic

What is Edison Effect?

Description : What is Edison Effect?

Last Answer : Ans-Edison Effect is also refferred as "Thermionic emission". Here the charge carriers flow from a charge-carrying surface due to vibrations caused by thermal energy. This phenomenon can be seen in ... electrical bulb in which is a metal filament is heated by the thermal energy from electricity.

What type of architecture is used in 8085 microprocessor?

Description : What type of architecture is used in 8085 microprocessor?

Last Answer : Ans- INTEL 8085 is a 8-bit microprocessor. It's based on Von-Neumann architecture in which the data and instructions are in the same memory space without any distinction between them. Data line: 8-bits--Can ... of data at a time. Address line: 16-bits--Can address upto 2^16(64KB) of address space.

Why we are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?

Description : Why we are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?

Last Answer : Ans-In bridge type (FWR) rectifiers center tapping transformer are not required so small transformers are used and we will get twice of the out put voltage that of the center tapped FWR.

What is function of ALE in 8085 microprocessor?

Description : What is function of ALE in 8085 microprocessor?

Last Answer : Ans-AlE stands for the address latch enableit 's working is that it differentiate the address and data bus in microprocessor.when it is high it select address bus .when it is low it select data bus.

What are the differences between microprocessor and micro controller.

Description : What are the differences between microprocessor and micro controller.

Last Answer : Ans-The microprocessor is the integration of a number of useful functions into a single IC package. These functions are: The ability to execute a stored set of instructions to carry out user defined ... contain a wealth of other modules such as Serial I/O Timers and Analogue to Digital Converters.