Description : The maximum ratio of span to depth of a slab simply supported and spanning in one direction, is (A) 35 (B) 25 (C) 30 (D) 20
Last Answer : Answer: Option C
Description : The maximum ratio of span to depth of a slab simply supported and spanning in one direction is (a) 35 (b) 25 (c) 30 (d) 20
Last Answer : (c) 30
Description : When the slab is supported on all the four edges and the ratio of long span to short span is small, bending takes place along both the spans, such a slab is known as (a) Slab spanning in one direction (b) One way slab. (c) Slab spanning in two direction. (d) Two-way slab.
Last Answer : (d) Two-way slab.
Description : The width of the flange of a T-beam should be less than (A) One-third of the effective span of the T-beam (B) Distance between the centres of T-beam (C) Breadth of the rib plus twelve times the thickness of the slab (D) Least of the above
Last Answer : Answer: Option D
Description : A T-beam behaves as a rectangular beam of a width equal to its flange if its neutral axis (A) Remains within the flange (B) Remains below the slab (C) Coincides the geometrical centre of the beam (D) None of these
Last Answer : Answer: Option A
Description : If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm
Description : The width of the flange of a L-beam, should be less than (A) One-sixth of the effective span (B) Breadth of the rib + four times thickness of the slab (C) Breadth of the rib + half clear distance between ribs (D) Least of the above
Description : In a T-beam , the breadth of the rib is equal to the (a) Total thickness of the slab, including cover (b) Width of the portion of the beam in the compression zone (c) Width of the portion of the beam in the compression zone (d) All the above.
Last Answer : (c) Width of the portion of the beam in the compression zone
Description : If the sides of a slab simply supported on edges and spanning in two directions are equal, the maximum bending moment is multiplied by (A) 0.2 (B) 0.3 (C) 0.4 (D) 0.5
Description : The maximum ratio of span to depth of a slab simply supported and spanning in two directions, is (A) 25 (B) 30 (C) 35 (D) 40
Description : The maximum ratio of span to depth of a slab simple supported and spanning in two directions, is (a) 25 (b) 30 (c) 35 (d) 40
Last Answer : (c) 35
Description : If the sides o a slab simply supported on its edges and spanning in two way are equal, then the maximum bending moment is multiplied by. (a) 0.25 (b) 0.50 (c) 0.75 (d) 0.85
Last Answer : (b) 0.50
Description : According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is ... (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab
Description : For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16
Description : If longitudinally spanning stairs are casted along with their landings, the maximum bending moment per metre width, is taken as (A) wl²/4 (B) wl²/8 (C) wl²/10 (D) wl²/12
Last Answer : Answer: Option B
Description : The portion of the slab which acts monolithically with the beam and which resists the compressive stresses, is called _________of flange of the T-beam (a) Length (b) Breadth (c) Thickness (d) Depth
Last Answer : (b) Breadth
Description : The width of a beam of uniform strength having a constant depth d length L, simply supported at the ends with a central load W is (A) 2WL/3fd² (B) 3WL/2fd² (C) 2fL/3Wd 4 (D) 3fL²/2Wd
Last Answer : (B) 3WL/2fd²
Description : The deflection of any rectangular beam simply supported, is (A) Directly proportional to its weight (B) Inversely proportional to its width (C) Inversely proportional to the cube of its depth (D) Directly proportional to the cube of its length
Last Answer : (C) Inversely proportional to the cube of its depth
Description : The thickness of base slab of a retaining wall generally provided, is (A) One half of the width of the stem at the bottom (B) One-third of the width of the stem at the bottom (C) One fourth of the width of the steam at the bottom (D) Width of the stem at the bottom
Description : If is the overall height of a retaining wall retaining a surcharge, the width of the base slab usually provided, is (A) 0.3 H (B) 0.4 H (C) 0.5 H (D) 0.7 H
Description : If K is a constant depending upon the ratio of the width of the slab to its effective span l, x is the distance of the concentrated load from the nearer support, bw is the width of the area of contact of the concentrated load measured ... ) Kx (1 - x/l) + bw (C) Kx (1 + x/l) + bw (D) All the above
Description : The effective width of a column strip of a flat slab, is (A) One-fourth the width of the panel (B) Half the width of the panel (C) Radius of the column (D) Diameter of the column
Description : In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above
Description : For a ribbed slab (A) Clear spacing between ribs shall not be greater than 4.5 cm (B) Width of the rib shall not be less than 7.5 cm (C) Overall depth of the slab shall not exceed four times the breadth of the rib (D) All the above
Description : If At is the area of steel cross-section, t is working stress, L is width of road and W is weight of slab per square metre, the spacing of the tie bars for a longitudinal joint, is (A) (100 At × t)/WL (B) 100 At/tWL (C) (100 WAt × t)/tL (D) 100 WL/At t
Description : If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm
Description : A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one- ... beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45
Description : A queen closer is a (A) Brick laid with its length parallel to the face or direction of wall (B) Brick laid with its breadth parallel to the face or direction of wall (C) Brick having the same ... bricks but half the breadth (D) Brick with half the width at one end and full width at the other
Description : A part of the slab may be considered as the flange of the T-beam if (A) Flange has adequate reinforcement transverse to beam (B) It is built integrally with the beam (C) It is effectively bonded together with the beam (D) All the above
Description : The neutral axis of a T-beam exists (A) Within the flange (B) At the bottom edge of the slab (C) Below the slab (D) All the above
Description : Minimum clear cover (in mm) to the main steel bars in slab, beam, column and footing respectively, are (a) 10, 15, 20 and 25 (b) 15, 25, 40 and 75 (c ) 20, 25, 30 and 40 (d) 20, 35, 40 and 75
Last Answer : (b) 15, 25, 40 and 75
Description : In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib
Last Answer : (d) Depth of rib
Description : Slab forms the compression flange of the T-beam (a) Yes (b) No (c) Not known (d) None of these
Last Answer : (a) Yes
Description : The thickness of flange in a T-beam is taken equal to the total thickness of the slab, including cover. (a) True (b) False (c) Not known (d) None of these
Last Answer : (a) True
Description : The breadth of the flange of a T-beam is (a) 1/3rd of the effective span of the T-beam (b) Twelve times the depth of slab plus breadth of rib. (c) Centre to centre distance between the adjacent beam. (d) Least of (a) , (b) or (c)
Last Answer : (d) Least of (a) , (b) or (c)
Description : Flanged beams are preferred when the concrete in the slab is on the [ A ] compression side of the beam [ B ] tension side of the beam [ C ] may be compression side or tension side of the beam [ D ] none of the above
Last Answer : [ A ] compression side of the beam
Description : The slab is said to be orthotropically reinforced , when the reinforcement is arranged in; [ A ] Single direction [ B ] Two directions at right angles with equal meshes [ C ] Two directions at right angles with unequal meshes [ D ] At the corners only
Last Answer : [ C ] Two directions at right angles with unequal meshes
Description : Minimum steel in the main direction of a slab when using high yield steel [ A ] 0.12% [ B ] 0.15% [ C ] 0.20% [ D ] 0.25%
Last Answer : [ B ] 0.15%
Description : The winch shown in the illustration will not operate in any speed in the lowering direction and at an abnormal speed in 'first point hoist'. The possible cause is that _______________. EL-0102 A. ... '1M' in the power circuit are badly corroded D. master switch contacts 'MS6' have weak springs
Last Answer : Answer: B
Description : For a strongest rectangular beam cut from a circular log, the ratio of the width and depth, is (A) 0.303 (B) 0.404 (C) 0.505 (D) 0.707
Last Answer : (D) 0.707
Description : If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection of the beam at the centre is changed by (A) 1/2 (B) 1/8 (C) 2 (D) 8
Last Answer : (A) 1/2
Description : If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection of the beam at the centre is changed by (A) 2 times (B) 4 times (C) 8 times (D) 1/2 times
Last Answer : (C) 8 times
Description : If the width b and depth d of a beam simply supported with a central load are interchanged, the deflection at the centre of the beam will be changed in the ratio of (A) b/d (B) d/b (C) (d/b)2 (D) (b/d)
Last Answer : (D) (b/d)2
Description : The width b and depth d of a beam cut from a wooden cylindrical log of 100 cm diameter for maximum strength are: (A) b = 57.73 cm d = 81.65 cm (B) b = 81.65 cm d = 57.73 cm (C) b = 50.00 cm d = 50.00 cm (D) b = 40.00 cm d = 80.00 cm
Last Answer : (A) b = 57.73 cm d = 81.65 cm
Description : A cantilever beam rectangular in cross-section is subjected to an isolated load at its free end. If the width of the beam is doubled, the deflection of the free end will be changed in the ratio of (A) 8 (B) 1/8 (C) 1/2 (D) 3
Last Answer : (C) 1/2
Description : If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm
Description : The reinforced concrete beam which has width 25 cm, lever arm 40 cm, shear force 6t/cm2 , safe shear stress 5 kg/cm2 and B.M. 24 mt, (A) Is safe in shear (B) Is unsafe in shear (C) Is over safe in shear (D) Needs redesigning
Description : The maximum shear stress (q) in concrete of a reinforced cement concrete beam is (A) Shear force/(Lever arm × Width) (B) Lever arm/(Shear force × Width) (C) Width/(Lever arm × Shear force) (D) (Shear force × Width)/Lever arm
Description : The width of the flange of a T-beam, which may be considered to act effectively with the rib depends upon (A) Breadth of the rib (B) Overall thickness of the rib (C) Centre to centre distance between T-beams (D) All the above