Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is proportional to D3(D = mean coil diameter) or d4(d = wire diameter) (C) Crushing load or columns is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2

Pick out the wrong statement.
(A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S
(B) For a helical spring, deflection is proportional to D3(D = mean coil diameter) or d4(d = wire diameter)
(C) Crushing load or columns is less than the buckling load
(D) Modulus of resilience is proportional to (stress at elastic limit)2
by

1 Answer

Answer :

(C) Crushing load or columns is less than the buckling load
by

Related questions

The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Description : The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Last Answer : (a)1/2

A closely coiled helical spring of radius R, contains n turns and is subjected to an axial load W. If the radius of the coil wire is r and modulus of rigidity of the coil material is C, the deflection of the coil is (A) WR3n/Cr4 (B) 2WR3n/Cr4 (C) 3WR3n/Cr4 (D) 4WR3n/Cr

Description : A closely coiled helical spring of radius R, contains n turns and is subjected to an axial load W. If  the radius of the coil wire is r and modulus of rigidity of the coil material is C, the deflection of the  coil is  (A) WR3n/Cr4 (B) 2WR3n/Cr4 (C) 3WR3n/Cr4 (D) 4WR3n/Cr

Last Answer : (D) 4WR3n/Cr

Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above

Description : Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above

Last Answer : b. 12.8 turns

When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring (B) Wire diameter of each spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Description : When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring ... spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Last Answer : (D) Square of wire diameter of each spring

The load on a spring per unit deflection, is called (A) Stiffness (B) Proof resilience (C) Proof stress (D) Proof load

Description : The load on a spring per unit deflection, is called  (A) Stiffness  (B) Proof resilience  (C) Proof stress  (D) Proof load

Last Answer : (A) Stiffness 

A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately a. increased by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Description : A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number ... by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Last Answer : a. increased by 8 times

The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Description : The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Last Answer : (D) Force required to produce unit deflection

A closely coiled helical spring of radius R, contains n turns and is subjected to an axial loadW. If the radius of the coil wire is r and modulus of rigidity of the coil material is C, the stress developed in the helical spring is (A) WR/ 3 (B) 2WR/ 3 (C) 2WR/ 2 (D) 4WR/ 2

Description : A closely coiled helical spring of radius R, contains n turns and is subjected to an axial loadW. If the radius of the coil wire is r and modulus of rigidity of the coil material is C, the stress developed in the helical spring is (A) WR/ 3 (B) 2WR/ 3 (C) 2WR/ 2 (D) 4WR/ 2

Last Answer : (B) 2WR/ 3

For long columns, the value of buckling load is……………..crushing load. (a) Less than (b) More than (c) Equal to (d) None of these

Description : For long columns, the value of buckling load is……………..crushing load. (a) Less than (b) More than (c) Equal to (d) None of these

Last Answer : (a) Less than

The capacity of a spring to store energy is called the spring form coefficient. Stiffness of a spring is measured by the (A) Ability to absorb shock (B) Capacity to store energy (C) Ratio of the wire & coil diameters (D) Load to produce unit deflection

Description : The capacity of a spring to store energy is called the spring form co-efficient. Stiffness of a spring is measured by the (A) Ability to absorb shock (B) Capacity to store energy (C) Ratio of the wire & coil diameters (D) Load to produce unit deflection

Last Answer : Option D

Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Last Answer : a) 7

Two close-coiled helical springs are equal in all respects except the number of turns. If the number of turns are in the ratio of 2:3, then the stiffness of the spring will be in the ratio of (a) 2:3 (b) 4:9 (c) 3:2 (d) 9:4

Description : Two close-coiled helical springs are equal in all respects except the number of turns. If the number of turns are in the ratio of 2:3, then the stiffness of the spring will be in the ratio of (a) 2:3 (b) 4:9 (c) 3:2 (d) 9:4

Last Answer : (c) 3:2

A close –coiled helical spring is cut into two equal parts. The stiffness of the resulting springs will be (a) same (b) double (c) half (d) One-fourth

Description : A close –coiled helical spring is cut into two equal parts. The stiffness of the resulting springs will be (a) same (b) double (c) half (d) One-fourth

Last Answer : (b) double

The greatest load which a spring can carry without getting permanently distorted, is called (A) Stiffness (B) Proof resilience (C) Proof stress (D) Proof load

Description : The greatest load which a spring can carry without getting permanently distorted, is called (A) Stiffness (B) Proof resilience (C) Proof stress (D) Proof load 

Last Answer : (D) Proof load 

The strain energy stored in a spring when subjected to greatest load without being permanently distorted, is called (A) Stiffness (B) Proof resilience (C) Proof stress (D) Proof load

Description : The strain energy stored in a spring when subjected to greatest load without being permanently  distorted, is called  (A) Stiffness  (B) Proof resilience  (C) Proof stress  (D) Proof load

Last Answer : (B) Proof resilience 

Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Description : Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Last Answer : b. 105.4 mm

The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Description : The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Last Answer : b) Spring stiffness

The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Description : The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Last Answer : (b) Spring stiffness

When two helical springs of equal lengths are arranged to form a cluster spring, then a. Shear stress in each spring will be equal b. Load taken by each spring will be half the total load c. Only A is correct d. Both A and B is correct

Description : When two helical springs of equal lengths are arranged to form a cluster spring, then a. Shear stress in each spring will be equal b. Load taken by each spring will be half the total load c. Only A is correct d. Both A and B is correct

Last Answer : d. Both A and B is correct

Find the shear stress in the spring wire used to design a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm² b) 468.6N/mm² c) 512.2N/mm² d) None of the listed

Description : Find the shear stress in the spring wire used to design a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm² b) 468.6N/mm² c) 512.2N/mm² d) None of the listed

Last Answer : b) 468.6N/mm²

Pick up the correct statement from the following: (A) The structural member subjected to compression and whose dimensions are small as compared to its length, is called a stmt (B) The vertical compression members are generally known as columns or stanchions (C) Deflection in lateral direction of a long column, is generally known as buckling (D) All the above

Description : Pick up the correct statement from the following:  (A) The structural member subjected to compression and whose dimensions are small as  compared to its length, is called a stmt  (B) The ... in lateral direction of a long column, is generally known as buckling  (D) All the above

Last Answer : (D) All the above

The torque transmitted by a hollow shaft of outer diameter (D) and inner diameter (d) (a)π/4fs(D2-d2)/D (b) π/4fs(D3-d3)/D (c) π/4fs(D4-d4)/D (d) π/4fs(D4-d4)/D

Description : The torque transmitted by a hollow shaft of outer diameter (D) and inner diameter (d) (a)π/4fs(D2-d2)/D (b) π/4fs(D3-d3)/D (c) π/4fs(D4-d4)/D (d) π/4fs(D4-d4)/D

Last Answer : (c) π/4fs(D4-d4)/D

The polar moment of inertia of a hollow shaft of outer diameter (D) and inner diameter (d) is given by. (a)π/16(D3-d3) (b) π/16(D4-d4) (c) π/16(D4-d4) (d) π/16(D4-d4/d)

Description : The polar moment of inertia of a hollow shaft of outer diameter (D) and inner diameter (d) is given by. (a)π/16(D3-d3) (b) π/16(D4-d4) (c) π/16(D4-d4) (d) π/16(D4-d4/d)

Last Answer : (b) π/16(D4-d4)

Pick up the correct statement from the following: (A) A wire wound in spiral form, is called a helical spring (B) The pitch of a close coil spring, is very small (C) The angle made by the coil with horizontal, is called the angle of helix (D) All the above

Description : Pick up the correct statement from the following:  (A) A wire wound in spiral form, is called a helical spring  (B) The pitch of a close coil spring, is very small  (C) The angle made by the coil with horizontal, is called the angle of helix  (D) All the above

Last Answer : (D) All the above

Two springs have spring stiffness of 1500 N/m and 1 KN/m respectively. If they are connected in series, what will be the equivalent spring stiffness? A 1KN/m B 600 N/m C 1 N/m D 600 KN/m

Description : Two springs have spring stiffness of 1500 N/m and 1 KN/m respectively. If they are connected in series, what will be the equivalent spring stiffness? A 1KN/m B 600 N/m C 1 N/m D 600 KN/m

Last Answer : B 600 N/m

Two springs have spring stiffness of 1500 N/m and 1 KN/m respectively. If they are connected in series, what will be the equivalent spring stiffness? A 1KN/m B 600 N/m C 1 N/m D 600 KN/m

Description : Two springs have spring stiffness of 1500 N/m and 1 KN/m respectively. If they are connected in series, what will be the equivalent spring stiffness? A 1KN/m B 600 N/m C 1 N/m D 600 KN/m

Last Answer : B 600 N/m

Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness if they are replaced by an equivalent system.3500 N/m A. 3500 N/m B. 1166 N/mC. 857.63 N/m D. None of the above

Description : Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness if they are replaced by an equivalent system.3500 N/m A. 3500 N/m B. 1166 N/mC. 857.63 N/m D. None of the above

Last Answer : C. 857.63 N/m

Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness if they are replaced by an equivalent system.3500 N/m A) 3500 N/m B) 1166 N/m C) 857.63 N/m D) None of the above

Description : Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness if they are replaced by an equivalent system.3500 N/m A) 3500 N/m B) 1166 N/m C) 857.63 N/m D) None of the above

Last Answer : C) 857.63 N/m

Two springs have spring stiffness of 1500 N/m and 1 KN/m respectively. If they B are connected in series, what will be the equivalent spring stiffness? (A) 1KN/m (B) 600 N/m (C) 1 N/m (D) 600 KN/m

Description : Two springs have spring stiffness of 1500 N/m and 1 KN/m respectively. If they B are connected in series, what will be the equivalent spring stiffness? (A) 1KN/m (B) 600 N/m (C) 1 N/m (D) 600 KN/m

Last Answer : (B) 600 N/m

Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness if they are replaced by an equivalent system.3500 N/m a. 3500 N/m b. 1166 N/m c. 857.63 N/m d. None of the above

Description : Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness if they are replaced by an equivalent system.3500 N/m a. 3500 N/m b. 1166 N/m c. 857.63 N/m d. None of the above

Last Answer : c. 857.63

Shear stress in a close coiled helical spring is (a) 16WD/π d3 (b) 32WD/π d3 (c) 8WD/π d3 (d) None

Description : Shear stress in a close coiled helical spring is (a) 16WD/π d3 (b) 32WD/π d3 (c) 8WD/π d3 (d) None

Last Answer : (c) 8WD/π d3

The spring constant of a helical compression spring does not depend on a. Coil diameter b. Material strength c. Number of active turns d. wire diameter

Description : The spring constant of a helical compression spring does not depend on a. Coil diameter b. Material strength c. Number of active turns d. wire diameter

Last Answer : b. Material strength

A close coil helical spring of mean diameter D consists of n coils of diameter d. If it carries an axial load W, the energy stored in the spring, is (A) 4WD²n/d 4N (B) 4W²Dn/d 4N (C) 4W²D3n/d 4N (D) 4W²D3n²/d 4N

Description : A close coil helical spring of mean diameter D consists of n coils of diameter d. If it carries an axial  load W, the energy stored in the spring, is  (A) 4WD²n/d 4N (B) 4W²Dn/d 4N (C) 4W²D3n/d 4N (D) 4W²D3n²/d 4N

Last Answer : (C) 4W²D3n/d 4N

The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Description : The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Last Answer : (C) Ratio of mean coil diameter to wire diameter

The stiffness of the close coil helical spring is (A) d 4N/8D 3n (B) d 4N/4D 3n (C) 4D 3N/d 4n (D) 8D 3N/d 4n

Description : The stiffness of the close coil helical spring is  (A) d 4N/8D 3n (B) d 4N/4D 3n (C) 4D 3N/d 4n (D) 8D 3N/d 4n

Last Answer : (A) d 4N/8D 3n

A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing stress of 124 N/mm2. G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Description : A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing ... G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Last Answer : a. 10 turns

Which of the following is measure of stiffness? a) Modulus of elasticity b) Modulus of plasticity c) Resilience d) Toughness

Description : Which of the following is measure of stiffness? a) Modulus of elasticity b) Modulus of plasticity c) Resilience d) Toughness

Last Answer : a) Modulus of elasticity

Initial gap between two turns of a close coil helical tension spring should be a. 0.5 mm b. based on the maximum deflection c. 1 mm d. zero

Description : Initial gap between two turns of a close coil helical tension spring should be a. 0.5 mm b. based on the maximum deflection c. 1 mm d. zero

Last Answer : d. zero

For the close coil helical spring of the maximum deflection is (A) WD3n/d 4N (B) 2WD3n/d 4N (C) 4W²D3n/d 4N (D) 8WD3n/d 4N

Description : For the close coil helical spring of the maximum deflection is  (A) WD3n/d 4N (B) 2WD3n/d 4N (C) 4W²D3n/d 4N (D) 8WD3n/d 4N

Last Answer : (D) 8WD3n/d 4N

The natural frequency of the spring mass is inversely proportional to A. Stiffness B. Mass C. Density D. Deflection

Description : The natural frequency of the spring mass is inversely proportional to A. Stiffness B. Mass C. Density D. Deflection

Last Answer : B. Mass

When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing

Description : When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing

Last Answer : (c) Torsion

A close-coiled helical spring of stiffness 30 N/mm is arranged in series with another such spring of stiffness 60 N/mm. The stiffness of composite unit is (a) 20 N/mm (b) 30 N/mm (c) 45 N/mm (d) 90 N/mm

Description : A close-coiled helical spring of stiffness 30 N/mm is arranged in series with another such spring of stiffness 60 N/mm. The stiffness of composite unit is (a) 20 N/mm (b) 30 N/mm (c) 45 N/mm (d) 90 N/mm

Last Answer : (a) 20 N/mm

If two springs having individual stiffness K, are in parallel, then their equivalent stiffness will be A. 2K B. K C. K/2 D. 4K

Description : If two springs having individual stiffness K, are in parallel, then their equivalent stiffness will be A. 2K B. K C. K/2 D. 4K

Last Answer : A. 2K

A close coil helical spring when subjected to a moment M having its axis along the axis of the helix (A) It is subjected to pure bending (B) Its mean diameter will decrease (C) Its number of coils will increase (D) All the above

Description : A close coil helical spring when subjected to a moment M having its axis along the axis of the helix  (A) It is subjected to pure bending  (B) Its mean diameter will decrease  (C) Its number of coils will increase  (D) All the above 

Last Answer : (A) It is subjected to pure bending 

Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness a. 3500 N/m b. 1166 N/m c. 857.63 N/m d. None of the above

Description : Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness a. 3500 N/m b. 1166 N/m c. 857.63 N/m d. None of the above

Last Answer : c. 857.63 N/m

A helical spring of constant k is cut into four equal pieces and the four pieces are then combined in parallel. The equivalent spring constant will be (a) k/16 (b) k/4 (c) 4k (d) 16k

Description : A helical spring of constant k is cut into four equal pieces and the four pieces are then combined in parallel. The equivalent spring constant will be (a) k/16 (b) k/4 (c) 4k (d) 16k

Last Answer : (d) 16k

spring material should have low (A) Elastic limit (B) Deflection value (C) Fatigue resistance (D) None of these

Description : spring material should have low (A) Elastic limit (B) Deflection value (C) Fatigue resistance (D) None of these

Last Answer : Option D

spring material should have low (A) Elastic limit (B) Deflection value (C) Fatigue resistance (D) None of these

Description : spring material should have low (A) Elastic limit (B) Deflection value (C) Fatigue resistance (D) None of these

Last Answer : Option D

If a close-coiled helical spring absorbs 50 N-mm of energy while extending by 5 mm, its stiffness will be (a) 2 N/mm (b) 4 N/mm (c) 6 N/mm (d) 10 N/mm

Description : If a close-coiled helical spring absorbs 50 N-mm of energy while extending by 5 mm, its stiffness will be (a) 2 N/mm (b) 4 N/mm (c) 6 N/mm (d) 10 N/mm

Last Answer : (d) 10 N/mm

The statement : stress is proportional to strain, i.e. the Hooke’s law holds good upto (a) Elastic Limit (b) Proportional Limit (c) Plastic Limit (d) Yield point

Description : The statement : stress is proportional to strain, i.e. the Hooke’s law holds good upto (a) Elastic Limit (b) Proportional Limit (c) Plastic Limit (d) Yield point

Last Answer : (b) Proportional Limit