Description : spring material should have low (A) Elastic limit (B) Deflection value (C) Fatigue resistance (D) None of these
Last Answer : Option D
Description : The most important property for the spring material is (a) High elastic limit (b) High deflection value (c) Resistance to fatigue and shock (d) All of these
Last Answer : (d) All of these
Description : Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these
Last Answer : (B) Endurance limit
Description : Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit
Last Answer : (D) Endurance limit
Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit
Last Answer : (d) endurance limit
Description : Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is ... is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2
Last Answer : (C) Crushing load or columns is less than the buckling load
Description : Fatigue limit improvement by over stressing the metal by successively increasing the load is called coaxing. In fatigue failure, the material fails (A) Below the yield point (B) Above the yield point (C) Below the elastic limit (D) At the elastic limit
Last Answer : Option A
Description : Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point
Last Answer : (d) below the yield point
Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point
Last Answer : (c) endurance limit to the working stress
Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping
Last Answer : a) Fatigue Failure
Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping
Last Answer : (a) Fatigue Failure
Description : Nitriding of a steel part does not increase its (A) Grain size (B) Fatigue limit (C) Surface hardness (D) Wear resistance
Last Answer : Option B
Description : The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the (A) Fatigue strength (B) Creep strength (C) Resilience (D) Endurance limit
Last Answer : D) Endurance limit
Description : The spring operates (A) Within plastic limit (B) Within elastic limit (C) Within elasto-plastic limit (D) Within visco-elastic limit
Last Answer : (B) Within elastic limit
Description : What is the maximum value of deforming force upto which a material shows elastic property and above which the material loses it? (1) Elasticity (2) Strain (3) Elastic Limit (4) Stress
Last Answer : (3) Elastic Limit Explanation: The Maximum Extent to which a solid may be stretched without permanent alteration of size or shape.
Description : What is the maximum value of deforming force up to which a material shows elastic property and above which the material loses it? (1) Elasticity (2) Strain (3) Elastic Limit (4) Stress
Last Answer : (4) Elastic Limit Explanation: The Maximum Extent to which a solid may be stretched without permanent alteration of size or shape.
Description : Why is it that the maximum value which the residual stress can reach is the elastic limit of the material ?
Last Answer : A stress in excess of elastic limit, with no external force to oppose it, will relieve itself by plastic deformation until it reaches the value of the yield stress.
Description : Why Is It That The Maximum Value Which The Residual Stress Can Reach Is The Elastic Limit Of The Material?
Last Answer : A stress more than the elastic limit, with no external force to oppose it, we relieve itself by plastic deformation until it reaches the value of the yield stress.
Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65
Last Answer : (c) 0.50
Description : A material no longer behaves elastically beyond (A) Plastic limit (B) Limiting load (C) Elastic limit (D) Breaking load
Last Answer : (C) Elastic limit
Description : Stresses encountered in the metal forming processes are less than the __________ of the material. (A) Fracture strength (B) Yield strength (C) Elastic limit (D) Limit of proportionality
Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)
Last Answer : (C) Creep resistance
Last Answer : (D) All (A), (B) & (C)
Description : Lead pipe is (A) Especially resistant to solutions containing H2SO4 (B) Usually joined by burning (e.g. by melting to adjacent pieces with a torch) (C) Having very low elastic limit resulting in permanent deformation from either mechanical or thermal strain (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C
Description : The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load
Last Answer : (d) completely reversed load
Description : The relationship between the alternating stress and mean stress is given by the following equation: σ a =σ e [1-(σ m /σ u )x], where σ e is the fatigue limit for completely reversed loading. The value of x for Gerber line is equal to _________ a) 1 b) 2 c) 0.5 d) -1
Last Answer : b) 2
Description : What is elastic fatigue or elastic fatigue ?
Last Answer : : If the stress applied to an elastic object at any angle can be continuously reduced and increased over a long period of time, then the elasticity of the object deteriorates even though the applied ... object as a result of a rapid decrease in pressure is called elastic fatigue or elastic fatigue.
Description : At yield point' of a copper wire A. the load hasn't exceeded the elastic limit yet; so, Hooke's law applies B. the load has already exceeded the elastic limit and the material has become ... stage has passed and the wire has snapped already D. Like Brass and Bronze, Copper has no yield poin
Last Answer : the load has already exceeded the elastic limit and the material has become plastic
Description : In a ductile material, the strength are (a)Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None
Last Answer : (a)Firstly Ultimate >yield > elastic limit
Description : In a brittle material, the strength are (a) Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None
Last Answer : (c) Thirdly Ultimate=yield=elastic limit
Description : Total strain energy theory for the failure of a material at elastic limit, is known (A) Guest's or Trecas' theory (B) St. Venant's theory (C) Rankine's theory (D) Haig's theory
Last Answer : (D) Haig's theory
Description : Shear strain energy theory for the failure of a material at elastic limit, is due to (A) Rankine (B) Guest or Trecas (C) St. Venant (D) Von Mises
Last Answer : (D) Von Mises
Description : Maximum shear stress theory for the failure of a material at the elastic limit, is known (A) Guest's or Trecas' theory (B) St. Venant's theory (C) Rankine's theory (D) Haig's theory
Last Answer : (A) Guest's or Trecas' theory
Description : Maximum strain theory for the failure of a material at the elastic limit, is known as (A) Guest's or Trecas' theory (B) St. Venant's theory (C) Rankine's theory (D) Haig's theory
Last Answer : (B) St. Venant's theory
Description : Every material obeys the Hooke's law within its (A) Elastic limit (B) Plastic point (C) Limit of proportionality (D) None of these
Last Answer : (C) Limit of proportionality
Description : When stress is increased beyond elastic limit and material is permanently changed this property is a) Permanent stress b) Elasticity c) Yield strength d) Plasticity
Last Answer : d) Plasticity
Description : The limit beyond which the material does not behave elastically is known as (a) Proportional limit (b) Elastic limit (c) Plastic limit (d) Yield Point
Last Answer : (b) Elastic limit
Description : Every material obeys the Hooke’s law within (a) Elastic limit (b) Plastic limit (c) Limit of proportionality (d) None of these
Last Answer : c) Limit of proportionality
Description : A closely coiled helical spring of radius R, contains n turns and is subjected to an axial load W. If the radius of the coil wire is r and modulus of rigidity of the coil material is C, the deflection of the coil is (A) WR3n/Cr4 (B) 2WR3n/Cr4 (C) 3WR3n/Cr4 (D) 4WR3n/Cr
Last Answer : (D) 4WR3n/Cr
Description : The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4
Last Answer : (a)1/2
Description : When testing a capacitor with an analog type ohmmeter, a good capacitor will be indicated when _____________. A. there is no meter deflection B. the meter deflects to a low resistance value and ... deflects to a low resistance value and increases rapidly to a higher value, but stays fairly low
Last Answer : Answer: C
Description : Distortion or change in shape of a cast partial denture clasp during its clinical use probably indicates that the: A. Ductility was too low B. Hardness was too great C. Ultimate tensile strength was too low D. Tension temperature was too high E. Elastic limit was exceeded
Last Answer : E. Elastic limit was exceeded
Description : Tumbling is the process of improving the __________ of the materials/parts. (A) Surface finish (B) Fatigue limit (C) Creep limit (D) Surface cleanliness
Description : A thick film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant
Last Answer : (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant
Description : A thin film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant
Last Answer : (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact
Description : A zero film bearing is a bearing (A) Where the surfaces of journal and the bearing are separated by a thick film of lubricant (B) Where the surfaces of journal and the bearing are partially ... bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant
Last Answer : (D) Where there is no lubricant
Description : Cast iron has (A) Very high tensile strength (B) High ductility (C) High malleability (D) Elastic limit close to ultimate breaking strength
Last Answer : (D) Elastic limit close to ultimate breaking strength
Description : All materials obey Hooke's law within elastic limit. When elastic limit is reached, the tensile strain (A) Increases very quickly (B) Decreases very quickly (C) Increases in proportion to stress (D) Decreases in proportion to stress
Last Answer : (A) Increases very quickly