Which of the following is the most common pump for pumping either raw sewage or sludge? (A) Electromagnetic pump (B) Centrifugal pump (C) Reciprocating pump(D) Gear pump

Which of the following is the most common pump for pumping either
raw sewage or sludge?
(A) Electromagnetic pump
(B) Centrifugal pump
(C) Reciprocating pump
(D) Gear pump
by

1 Answer

Answer :

(C) Reciprocating pump
by

Related questions

Which of the following is used for pumping crude oil from oil well? (A) Single stage centrifugal pump (B) Gear pump (C) Screw pump (D) Duplex/triplex reciprocating pump

Description : Which of the following is used for pumping crude oil from oil well? (A) Single stage centrifugal pump (B) Gear pump (C) Screw pump (D) Duplex/triplex reciprocating pump

Last Answer : (D) Duplex/triplex reciprocating pump

The type of pump used for lifting large quantity of sewage is a __________ pump. (A) Gear (B) Centrifugal (C) Reciprocating (D) Plunger

Description : The type of pump used for lifting large quantity of sewage is a __________ pump. (A) Gear (B) Centrifugal (C) Reciprocating (D) Plunger

Last Answer : (B) Centrifugal

For pumping slurry, one can use a __________ pump. (A) Reciprocating (B) Diaphragm (C) Centrifugal (D) Pneumatic

Description : For pumping slurry, one can use a __________ pump. (A) Reciprocating (B) Diaphragm (C) Centrifugal (D) Pneumatic

Last Answer : (B) Diaphragm

Boiler feed water pump is usually a __________ pump.(A) Reciprocating (B) Gear (C) Multistage centrifugal (D) Diaphragm

Description : Boiler feed water pump is usually a __________ pump. (A) Reciprocating (B) Gear (C) Multistage centrifugal (D) Diaphragm

Last Answer : (C) Multistage centrifugal

Maintenance cost of a __________ pump for a particular duty is the least. (A) Centrifugal (B) Reciprocating (C) Volute (D) Gear

Description : Maintenance cost of a __________ pump for a particular duty is the least. (A) Centrifugal (B) Reciprocating (C) Volute (D) Gear

Last Answer : (A) Centrifugal

Molten soap mass is transported by a __________ pump. (A) Diaphragm (B) Reciprocating (C) Gear (D) Centrifugal

Description : Molten soap mass is transported by a __________ pump. (A) Diaphragm (B) Reciprocating (C) Gear (D) Centrifugal

Last Answer : (D) Centrifugal

For the transfer of solution of thick slurry, the pump used is a __________ pump(A) Reciprocating(B) Gear(C) Diaphragm(D) Centrifugal.

Description : For the transfer of solution of thick slurry, the pump used is a __________ pump. (A) Reciprocating (B) Gear (C) Diaphragm (D) Centrifugal

Last Answer : (C) Diaphragm

Priming is needed in a __________ pump. (A) Reciprocating (B) Gear (C) Centrifugal (D) Diaphragm

Description : Priming is needed in a __________ pump. (A) Reciprocating (B) Gear (C) Centrifugal (D) Diaphragm

Last Answer : (C) Centrifugal

Which of the following is most prone to pulsating discharge flow? (A) Centrifugal pump(B) Reciprocating pump(C) Gear pump(D) Axial flow pump

Description : Which of the following is most prone to pulsating discharge flow? (A) Centrifugal pump (B) Reciprocating pump (C) Gear pump (D) Axial flow pump

Last Answer : (C) Gear pump

Pump used for the transportation of molten sodium in a fast breader reactor is a/an __________ pump. (A) Reciprocating (B) Plunger (C) Electromagnetic (D) Gear

Description : Pump used for the transportation of molten sodium in a fast breader reactor is a/an __________ pump. (A) Reciprocating (B) Plunger (C) Electromagnetic (D) Gear

Last Answer : (C) Electromagnetic

The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute

Description : The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute

Last Answer : (A) Electromagnetic

The non-clog pump which permits solid matter to pass out with the liquid sewage, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Description : The non-clog pump which permits solid matter to pass out with the liquid sewage, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Last Answer : ANS: A

Q No: 131 The most widely used pump for lifting sewage is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. Air pressure pump

Description : Q No: 131 The most widely used pump for lifting sewage is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. Air pressure pump

Last Answer : ANS: A

Which of the following pumps in used to pump sewage solids with liquid sewage without clogging the pump is? A. Centrifugal pump B. Pneumatic ejector C. Reciprocating pump D. None of these

Description : Which of the following pumps in used to pump sewage solids with liquid sewage without clogging the pump is? A. Centrifugal pump B. Pneumatic ejector C. Reciprocating pump D. None of these

Last Answer : ANS: A

Reciprocating pumps (A) Are not suitable for variable heads (B) Are four times costlier than centrifugal pumps (C) Are not suitable for pumping water containing sediments (D) Single stroke produce pulsating flow

Description : Reciprocating pumps  (A) Are not suitable for variable heads  (B) Are four times costlier than centrifugal pumps  (C) Are not suitable for pumping water containing sediments  (D) Single stroke produce pulsating flow 

Last Answer : (A) Are not suitable for variable heads 

Pumping of a corrosive liquid is generally preferred to be done by a __________ pump, as it can be made of a variety of materials including plastics. (A) Piston (B) Gear (C) Positive displacement (D) Sump

Description : Pumping of a corrosive liquid is generally preferred to be done by a __________ pump, as it can be made of a variety of materials including plastics. (A) Piston (B) Gear (C) Positive displacement (D) Sump

Last Answer : (B) Gear

Slurries can be most conveniently pumped by a __________ pump. (A) Screw (B) Reciprocating (C) Gear (D) Centrifuga

Description : Slurries can be most conveniently pumped by a __________ pump. (A) Screw (B) Reciprocating (C) Gear (D) Centrifuga

Last Answer : (D) Centrifuga

Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) NPSH required (B) BHP required by the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow

Self-priming centrifugal pump can be used for (A) Booster service (B) Pumping liquid fertilisers (e.g. liquid NH3 ) (C) Pumping industrial wastes (D) All (A), (B) and (C)

Description : Self-priming centrifugal pump can be used for (A) Booster service (B) Pumping liquid fertilisers (e.g. liquid NH3 ) (C) Pumping industrial wastes (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A centrifugal pump designed for handling water (μ = 1 cp) will deliver __________ when pumping a thicker oil (μ = 30 cp). (A) Less head & capacity (B) More head (C) More capacity (D) Less head & more capacity

Description : A centrifugal pump designed for handling water (μ = 1 cp) will deliver __________ when pumping a thicker oil (μ = 30 cp). (A) Less head & capacity (B) More head (C) More capacity (D) Less head & more capacity

Last Answer : (A) Less head & capacity

Reciprocating pumps are not able to compete with the centrifugal pump for industrial use, mainly because these pumps have (A) Very low speeds (B) Smaller discharge (C) Higher capital &maintenance cost (D) High vibrations

Description : Reciprocating pumps are not able to compete with the centrifugal pump for industrial use, mainly because these pumps have (A) Very low speeds (B) Smaller discharge (C) Higher capital &maintenance cost (D) High vibrations

Last Answer : (C) Higher capital &maintenance cost

To handle smaller quantity of fluid at higher discharge pressure, use a __________ pump. (A) Reciprocating (B) Centrifugal (C) Volute (D) Rotary vacuum

Description : To handle smaller quantity of fluid at higher discharge pressure, use a __________ pump. (A) Reciprocating (B) Centrifugal (C) Volute (D) Rotary vacuum

Last Answer : (A) Reciprocating

In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) Discharge of water by a centrifugal pump being run at a constant rpm (B) Water flow in the suction and discharge pipe of a reciprocating pump (C) Water discharge from a vertical vessel in which constant level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump

In a naturally aspirated diesel engine, the air is supplied by a A. supercharger B. centrifugal pump C. movement of engine piston D. reciprocating pump

Description : In a naturally aspirated diesel engine, the air is supplied by a A. supercharger B. centrifugal pump C. movement of engine piston D. reciprocating pump

Last Answer : ANSWER : C

The disintegrating pump in which solid matter is broken up before passing out, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Description : The disintegrating pump in which solid matter is broken up before passing out, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Last Answer : ANS: A

Most commonly used pump for lifting water in water supply mains, is (A) Axial flow pump (B) Reciprocating pump (C) Rotary type pump (D) Centrifugal pumps

Description : Most commonly used pump for lifting water in water supply mains, is  (A) Axial flow pump  (B) Reciprocating pump  (C) Rotary type pump  (D) Centrifugal pumps 

Last Answer : (A) Axial flow pump 

The depth of the water table at a place is 45 m below the general ground level. To lift water from a deep tube well in such a locality, the type of pump to be installed is (A) Centrifugal pump (B) Reciprocating pump (C) Deep well turbine pump (D) None of these

Description : The depth of the water table at a place is 45 m below the general ground level. To lift water from a  deep tube well in such a locality, the type of pump to be installed is  (A) Centrifugal pump  (B) Reciprocating pump  (C) Deep well turbine pump  (D) None of these 

Last Answer : (C) Deep well turbine pump

Which Pump Is More Efficient Centrifugal Pump Or Reciprocating Pump?

Description : Which Pump Is More Efficient Centrifugal Pump Or Reciprocating Pump?

Last Answer : Centrifugal pump. Because flow rate is higher compared to reciprocating pump. Flow is smooth and it requires less space to install. Lower initial cost and lower maintenance cost.

A ____ pump consists of a reciprocating or rotating cavity between two lobes or gears and a rotor. a. positive c. negative b. centrifugal d. hand

Description : A ____ pump consists of a reciprocating or rotating cavity between two lobes or gears and a rotor. a. positive c. negative b. centrifugal d. hand

Last Answer : a. positive

Differentiate Reciprocating pump with centrifugal pump.

Description : Differentiate Reciprocating pump with centrifugal pump.

Last Answer : Sr. No. Reciprocating Pump Centrifugal Pump 1 For Reciprocating pump discharge is fluctuating.  For Centrifugal pump discharge is continuous. 2 Suitable for less ... more floor area and requires heavy foundation. Requires less floor area and simple foundation.

Crude oil is pumped by a __________ pump. (A) Gear (B) Centrifugal

Description : Crude oil is pumped by a __________ pump. (A) Gear (B) Centrifugal

Last Answer : (B) Centrifugal

Gear pump (A) Is a positive displacement pump (B) Is a centrifugal pump (C) Is a non-positive displacement pump (D) Can be started with delivery valve closed

Description : Gear pump (A) Is a positive displacement pump (B) Is a centrifugal pump (C) Is a non-positive displacement pump (D) Can be started with delivery valve closed

Last Answer : (A) Is a positive displacement pump

The pump used in airplane sprayers: A. Dentrifugal and gear pump B. Gear and Diaphragm pump C. Diaphragm and centrifugal pump D. Plunger and centrifugal pump

Description : The pump used in airplane sprayers: A. Dentrifugal and gear pump B. Gear and Diaphragm pump C. Diaphragm and centrifugal pump D. Plunger and centrifugal pump

Last Answer : Dentrifugal and gear pump

While starting a centrifugal pump, its delivery valve should be kept (A) Opened (B) Closed (C) Either opened or closed; it does not make any difference (D) Either opened or closed; depending on the fluid viscosity

Description : While starting a centrifugal pump, its delivery valve should be kept (A) Opened (B) Closed (C) Either opened or closed; it does not make any difference (D) Either opened or closed; depending on the fluid viscosity

Last Answer : (B) Closed

Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes in the impeller (C) Mounting of two or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Description : Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes ... or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Last Answer : (C) Mounting of two or more impellers in series on a single shaft

Sewage sludge is an example of the __________ fluid. (A) Bingham plastic (B) Newtonian (C) Pseudo plastic (D) Dilatent

Description : Sewage sludge is an example of the __________ fluid. (A) Bingham plastic (B) Newtonian (C) Pseudo plastic (D) Dilatent

Last Answer : (A) Bingham plastic

Sewage sludge is __________ type of non-Newtonian fluid. (A) Dilatant (B) Bingham plastic (C) Pseudo plastic (D) None of these

Description : Sewage sludge is __________ type of non-Newtonian fluid. (A) Dilatant (B) Bingham plastic (C) Pseudo plastic (D) None of these

Last Answer : (B) Bingham plastic

An ideal plastic substance indicates no deformation, when stressed upto yield stress, but behaves like a Newtonian fluid beyond yield stress. Which of the following is an ideal plastic? (A) Sewage sludge (B) Rubber latex (C) Blood (D) Sugar solution

Description : An ideal plastic substance indicates no deformation, when stressed upto yield stress, but behaves like a Newtonian fluid beyond yield stress. Which of the following is an ideal plastic? (A) Sewage sludge (B) Rubber latex (C) Blood (D) Sugar solution

Last Answer : (A) Sewage sludge

Which of the following is a Newtonian fluid? (A) Rubber latex (B) Sewage sludge (C) Quicksand (D) Non-colloidal solution

Description : Which of the following is a Newtonian fluid? (A) Rubber latex (B) Sewage sludge (C) Quicksand (D) Non-colloidal solution

Last Answer : (D) Non-colloidal solution

The main type of sludge gas evolved during sewage treatment in Imhoff tank is (A) CO2 (B) CH4 (C) CO (D) H2

Description : The main type of sludge gas evolved during sewage treatment in Imhoff tank is (A) CO2 (B) CH4 (C) CO (D) H2

Last Answer : (B) CH4

Use of chlorine in the treatment of sewage (A) Helps in grease separation (B) Increases the biological oxygen demand (BOD) (C) Causes bulking of activated sludge (D) Aids in flocculation

Description : Use of chlorine in the treatment of sewage (A) Helps in grease separation (B) Increases the biological oxygen demand (BOD) (C) Causes bulking of activated sludge (D) Aids in flocculation

Last Answer : (A) Helps in grease separation

Reciprocating pumps compared to centrifugal pumps (A) Deliver liquid at uniform pressure (B) Can handle slurries more efficiently (C) Are not subject to air binding (D) Can be operated with delivery valve closed

Description : Reciprocating pumps compared to centrifugal pumps (A) Deliver liquid at uniform pressure (B) Can handle slurries more efficiently (C) Are not subject to air binding (D) Can be operated with delivery valve closed

Last Answer : (C) Are not subject to air binding

Centrifugal compressors compared to reciprocating compressors (A) Require less space (B) Have quieter operation (C) Have lower operating costs (D) All (A), (B) and (C)

Description : Centrifugal compressors compared to reciprocating compressors (A) Require less space (B) Have quieter operation (C) Have lower operating costs (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which of the following can be used to create a flow of gas, where no significant compression is required? (A) Reciprocating compressor (B) Blower (C) Axial flow compressor (D) Centrifugal compressor

Description : Which of the following can be used to create a flow of gas, where no significant compression is required? (A) Reciprocating compressor (B) Blower (C) Axial flow compressor (D) Centrifugal compressor

Last Answer : (B) Blower

Centrifugal pumps as compared to reciprocating pumps (A) Run at a lower speed for the same discharge (B) Do not need priming (C) Deliver fluid with pulsating/fluctuating discharge (D) Can be run with discharge line valve closed for a short interval

Description : Centrifugal pumps as compared to reciprocating pumps (A) Run at a lower speed for the same discharge (B) Do not need priming (C) Deliver fluid with pulsating/fluctuating discharge (D) Can be run with discharge line valve closed for a short interval

Last Answer : (D) Can be run with discharge line valve closed for a short interval

Sewage sludge is used as Tipping is a technique of

Description : Sewage sludge is used as Tipping is a technique of

Last Answer : Sewage sludge is used as Tipping is a technique of A. manure B. biogas generator C. Both A and B D. Tipping

______ is a by product of sewage treatment and can be decomposed to produce biogas. (1) Sewage (2) Sludge (3) Sewer (4) Scum

Description : ______ is a by product of sewage treatment and can be decomposed to produce biogas. (1) Sewage (2) Sludge (3) Sewer (4) Scum

Last Answer : (2) Sludge Explanation: Sludge refers to the residual, semi-solid material that is produced as a byproduct during sewage treatment of industrial or municipal wastewater. It can be used to produce biogas through a process called anaerobic digestion or fermentation.

The detention time (t) of a settling tank, may be defined as the time required for A. A particle to travel along its length B. A particle to travel from top surface to bottom sludge zone C. The flow of sewage to fill the tank D. None of these

Description : The detention time (t) of a settling tank, may be defined as the time required for A. A particle to travel along its length B. A particle to travel from top surface to bottom sludge zone C. The flow of sewage to fill the tank D. None of these

Last Answer : ANS: C