Reciprocating pumps are not able to compete with the centrifugal pump for industrial use, mainly because these pumps have (A) Very low speeds (B) Smaller discharge (C) Higher capital &maintenance cost (D) High vibrations

Reciprocating pumps are not able to compete with the centrifugal
pump for industrial use, mainly because these pumps have
(A) Very low speeds
(B) Smaller discharge
(C) Higher capital &maintenance cost
(D) High vibrations
by

1 Answer

Answer :

(C) Higher capital &maintenance cost
by

Related questions

To handle smaller quantity of fluid at higher discharge pressure, use a __________ pump. (A) Reciprocating (B) Centrifugal (C) Volute (D) Rotary vacuum

Description : To handle smaller quantity of fluid at higher discharge pressure, use a __________ pump. (A) Reciprocating (B) Centrifugal (C) Volute (D) Rotary vacuum

Last Answer : (A) Reciprocating

Centrifugal pumps as compared to reciprocating pumps (A) Run at a lower speed for the same discharge (B) Do not need priming (C) Deliver fluid with pulsating/fluctuating discharge (D) Can be run with discharge line valve closed for a short interval

Description : Centrifugal pumps as compared to reciprocating pumps (A) Run at a lower speed for the same discharge (B) Do not need priming (C) Deliver fluid with pulsating/fluctuating discharge (D) Can be run with discharge line valve closed for a short interval

Last Answer : (D) Can be run with discharge line valve closed for a short interval

In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) Discharge of water by a centrifugal pump being run at a constant rpm (B) Water flow in the suction and discharge pipe of a reciprocating pump (C) Water discharge from a vertical vessel in which constant level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump

Which of the following pumps in used to pump sewage solids with liquid sewage without clogging the pump is? A. Centrifugal pump B. Pneumatic ejector C. Reciprocating pump D. None of these

Description : Which of the following pumps in used to pump sewage solids with liquid sewage without clogging the pump is? A. Centrifugal pump B. Pneumatic ejector C. Reciprocating pump D. None of these

Last Answer : ANS: A

Most commonly used pump for lifting water in water supply mains, is (A) Axial flow pump (B) Reciprocating pump (C) Rotary type pump (D) Centrifugal pumps

Description : Most commonly used pump for lifting water in water supply mains, is  (A) Axial flow pump  (B) Reciprocating pump  (C) Rotary type pump  (D) Centrifugal pumps 

Last Answer : (A) Axial flow pump 

Which of the following is most prone to pulsating discharge flow? (A) Centrifugal pump(B) Reciprocating pump(C) Gear pump(D) Axial flow pump

Description : Which of the following is most prone to pulsating discharge flow? (A) Centrifugal pump (B) Reciprocating pump (C) Gear pump (D) Axial flow pump

Last Answer : (C) Gear pump

Multistage centrifugal pumps are generally used for (A) High head (B) Low head but high discharge (C) Highly viscous liquid (D) Slurries of high solid concentration

Description : Multistage centrifugal pumps are generally used for (A) High head (B) Low head but high discharge (C) Highly viscous liquid (D) Slurries of high solid concentration

Last Answer : (A) High head

For centrifugal pumps (A) Initial cost is low (B) Limited space is required (C) The discharge obtained is steady and non-pulsating (D) All the above

Description : For centrifugal pumps  (A) Initial cost is low  (B) Limited space is required  (C) The discharge obtained is steady and non-pulsating  (D) All the above 

Last Answer : (D) All the above 

Reciprocating pumps compared to centrifugal pumps (A) Deliver liquid at uniform pressure (B) Can handle slurries more efficiently (C) Are not subject to air binding (D) Can be operated with delivery valve closed

Description : Reciprocating pumps compared to centrifugal pumps (A) Deliver liquid at uniform pressure (B) Can handle slurries more efficiently (C) Are not subject to air binding (D) Can be operated with delivery valve closed

Last Answer : (C) Are not subject to air binding

Pick up the correct statement from the following regarding radial flow centrifugal pumps: (A) These are provided with volute type or turbine type casings (B) In involute type of radial flow centrifugal pump, the impeller discharges into a gradually expanding spiral casing (C) The efficiency of turbine type of radial flow centrifugal pump, is always higher than that of volute type (D) All the above

Description : Pick up the correct statement from the following regarding radial flow centrifugal pumps:  (A) These are provided with volute type or turbine type casings  (B) In involute type of radial flow ... centrifugal pump, is always higher than that of  volute type  (D) All the above 

Last Answer : (D) All the above 

Reciprocating pumps (A) Are not suitable for variable heads (B) Are four times costlier than centrifugal pumps (C) Are not suitable for pumping water containing sediments (D) Single stroke produce pulsating flow

Description : Reciprocating pumps  (A) Are not suitable for variable heads  (B) Are four times costlier than centrifugal pumps  (C) Are not suitable for pumping water containing sediments  (D) Single stroke produce pulsating flow 

Last Answer : (A) Are not suitable for variable heads 

Consider the following statements: Air vessels are fitted on the suction and delivery sides of a reciprocating pump to 1. Achieve higher speed without separation. 2. Reduce work in overcoming frictional resistance. 3. Avoid excessive vibration permanently. 4. Have nearly uniform discharge. Which of these statements are corrects? (a) 1, 2 & 4 only (b) 1, 2 & 3 only (c) 2, 3 & 4 only (d) 1, 2, 3 & 4

Description : Consider the following statements: Air vessels are fitted on the suction and delivery sides of a reciprocating pump to 1. Achieve higher speed without separation. 2. Reduce work in overcoming frictional resistance. 3. Avoid excessive vibration ... 2 & 3 only (c) 2, 3 & 4 only (d) 1, 2, 3 & 4

Last Answer : (d) 1, 2, 3 & 4

Maintenance cost of a __________ pump for a particular duty is the least. (A) Centrifugal (B) Reciprocating (C) Volute (D) Gear

Description : Maintenance cost of a __________ pump for a particular duty is the least. (A) Centrifugal (B) Reciprocating (C) Volute (D) Gear

Last Answer : (A) Centrifugal

For pumping slurry, one can use a __________ pump. (A) Reciprocating (B) Diaphragm (C) Centrifugal (D) Pneumatic

Description : For pumping slurry, one can use a __________ pump. (A) Reciprocating (B) Diaphragm (C) Centrifugal (D) Pneumatic

Last Answer : (B) Diaphragm

The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute

Description : The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute

Last Answer : (A) Electromagnetic

Boiler feed water pump is usually a __________ pump.(A) Reciprocating (B) Gear (C) Multistage centrifugal (D) Diaphragm

Description : Boiler feed water pump is usually a __________ pump. (A) Reciprocating (B) Gear (C) Multistage centrifugal (D) Diaphragm

Last Answer : (C) Multistage centrifugal

Molten soap mass is transported by a __________ pump. (A) Diaphragm (B) Reciprocating (C) Gear (D) Centrifugal

Description : Molten soap mass is transported by a __________ pump. (A) Diaphragm (B) Reciprocating (C) Gear (D) Centrifugal

Last Answer : (D) Centrifugal

For the transfer of solution of thick slurry, the pump used is a __________ pump(A) Reciprocating(B) Gear(C) Diaphragm(D) Centrifugal.

Description : For the transfer of solution of thick slurry, the pump used is a __________ pump. (A) Reciprocating (B) Gear (C) Diaphragm (D) Centrifugal

Last Answer : (C) Diaphragm

Priming is needed in a __________ pump. (A) Reciprocating (B) Gear (C) Centrifugal (D) Diaphragm

Description : Priming is needed in a __________ pump. (A) Reciprocating (B) Gear (C) Centrifugal (D) Diaphragm

Last Answer : (C) Centrifugal

Which of the following is used for pumping crude oil from oil well? (A) Single stage centrifugal pump (B) Gear pump (C) Screw pump (D) Duplex/triplex reciprocating pump

Description : Which of the following is used for pumping crude oil from oil well? (A) Single stage centrifugal pump (B) Gear pump (C) Screw pump (D) Duplex/triplex reciprocating pump

Last Answer : (D) Duplex/triplex reciprocating pump

Which of the following is the most common pump for pumping either raw sewage or sludge? (A) Electromagnetic pump (B) Centrifugal pump (C) Reciprocating pump(D) Gear pump

Description : Which of the following is the most common pump for pumping either raw sewage or sludge? (A) Electromagnetic pump (B) Centrifugal pump (C) Reciprocating pump (D) Gear pump

Last Answer : (C) Reciprocating pump

The type of pump used for lifting large quantity of sewage is a __________ pump. (A) Gear (B) Centrifugal (C) Reciprocating (D) Plunger

Description : The type of pump used for lifting large quantity of sewage is a __________ pump. (A) Gear (B) Centrifugal (C) Reciprocating (D) Plunger

Last Answer : (B) Centrifugal

For very low pressure and high discharge rate, the compressor used is a/an __________ compressor. (A) Axial (B) Reciprocating (C) Rotary (D) None of these

Description : For very low pressure and high discharge rate, the compressor used is a/an __________ compressor. (A) Axial (B) Reciprocating (C) Rotary (D) None of these

Last Answer : (C) Rotary

The main draw-back of centrifugal pump, is (A) Necessity of priming (B) Discharge from pump varies with the load of water (C) For high heads, efficiency is low up to 50% (D) All the above

Description : The main draw-back of centrifugal pump, is (A) Necessity of priming (B) Discharge from pump varies with the load of water (C) For high heads, efficiency is low up to 50% (D) All the above

Last Answer : (D) All the above

The main drawback of centrifugal pump is a)necessity of priming b) discharge from pump varies with the load of water c) For high heads efficiency is low up to 50% d) the suction lift is limited to 6 metre e) all of the above*

Description : The main drawback of centrifugal pump is a)necessity of priming b) discharge from pump varies with the load of water c) For high heads efficiency is low up to 50% d) the suction lift is limited to 6 metre e) all of the above*

Last Answer : e) all of the above*

A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow

The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Description : The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

For a reciprocating pump, the indicator diagram is the graph between the (A) Discharge and overall efficiency (B) Volume swept by piston for one complete revolution and the pressure in the cylinder (C) Angle swept by the crank pin at any instant and the discharge (D) None of these

Description : For a reciprocating pump, the indicator diagram is the graph between the (A) Discharge and overall efficiency (B) Volume swept by piston for one complete revolution and the pressure in the cylinder (C) Angle swept by the crank pin at any instant and the discharge (D) None of these

Last Answer : (B) Volume swept by piston for one complete revolution and the pressure in the cylinder

A double acting reciprocating pump compared to a single acting pump (of almost same size working under same pressure levels) would give almost double (A) Head (B) Discharge (C) Efficiency (D) None of these

Description : A double acting reciprocating pump compared to a single acting pump (of almost same size working under same pressure levels) would give almost double (A) Head (B) Discharge (C) Efficiency (D) None of these

Last Answer : (B) Discharge

Function of air vessel provided in a reciprocating pump is to (A) Reduce discharge fluctuation (B) Reduce the danger of cavitation (C) Avoid the necessity of priming (D) Increase the pump efficiency

Description : Function of air vessel provided in a reciprocating pump is to (A) Reduce discharge fluctuation (B) Reduce the danger of cavitation (C) Avoid the necessity of priming (D) Increase the pump efficiency

Last Answer : (A) Reduce discharge fluctuation

Air vessel fitted to a reciprocating pump (A) Increases the work done (B) Decreases the work done (C) Causes cavitation (D) Results in non-uniform discharge

Description : Air vessel fitted to a reciprocating pump (A) Increases the work done (B) Decreases the work done (C) Causes cavitation (D) Results in non-uniform discharge

Last Answer : (B) Decreases the work done

Purpose of relief valve in a reciprocating pump is to (A) Protect the pump against developing excessive pressure (B) Facilitate unidirectional flow of liquid (C) Reduce the discharge pressure (D) Control the rate of discharge

Description : Purpose of relief valve in a reciprocating pump is to (A) Protect the pump against developing excessive pressure (B) Facilitate unidirectional flow of liquid (C) Reduce the discharge pressure (D) Control the rate of discharge

Last Answer : (A) Protect the pump against developing excessive pressure

In a naturally aspirated diesel engine, the air is supplied by a A. supercharger B. centrifugal pump C. movement of engine piston D. reciprocating pump

Description : In a naturally aspirated diesel engine, the air is supplied by a A. supercharger B. centrifugal pump C. movement of engine piston D. reciprocating pump

Last Answer : ANSWER : C

The non-clog pump which permits solid matter to pass out with the liquid sewage, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Description : The non-clog pump which permits solid matter to pass out with the liquid sewage, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Last Answer : ANS: A

The disintegrating pump in which solid matter is broken up before passing out, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Description : The disintegrating pump in which solid matter is broken up before passing out, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Last Answer : ANS: A

Q No: 131 The most widely used pump for lifting sewage is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. Air pressure pump

Description : Q No: 131 The most widely used pump for lifting sewage is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. Air pressure pump

Last Answer : ANS: A

The depth of the water table at a place is 45 m below the general ground level. To lift water from a deep tube well in such a locality, the type of pump to be installed is (A) Centrifugal pump (B) Reciprocating pump (C) Deep well turbine pump (D) None of these

Description : The depth of the water table at a place is 45 m below the general ground level. To lift water from a  deep tube well in such a locality, the type of pump to be installed is  (A) Centrifugal pump  (B) Reciprocating pump  (C) Deep well turbine pump  (D) None of these 

Last Answer : (C) Deep well turbine pump

Which Pump Is More Efficient Centrifugal Pump Or Reciprocating Pump?

Description : Which Pump Is More Efficient Centrifugal Pump Or Reciprocating Pump?

Last Answer : Centrifugal pump. Because flow rate is higher compared to reciprocating pump. Flow is smooth and it requires less space to install. Lower initial cost and lower maintenance cost.

A ____ pump consists of a reciprocating or rotating cavity between two lobes or gears and a rotor. a. positive c. negative b. centrifugal d. hand

Description : A ____ pump consists of a reciprocating or rotating cavity between two lobes or gears and a rotor. a. positive c. negative b. centrifugal d. hand

Last Answer : a. positive

Differentiate Reciprocating pump with centrifugal pump.

Description : Differentiate Reciprocating pump with centrifugal pump.

Last Answer : Sr. No. Reciprocating Pump Centrifugal Pump 1 For Reciprocating pump discharge is fluctuating.  For Centrifugal pump discharge is continuous. 2 Suitable for less ... more floor area and requires heavy foundation. Requires less floor area and simple foundation.

Conversion of dynamic velocity head into static pressure head in a centrifugal pump is the result of : (a) Increasing area of flow between adjacent vanes from inlet to outlet (b) Difference in pressure between suction and delivery ends (c) Radial thrust in pumps (d) Stuffing Box

Description : Conversion of dynamic velocity head into static pressure head in a centrifugal pump is the result of : (a) Increasing area of flow between adjacent vanes from inlet to outlet (b) Difference in pressure between suction and delivery ends (c) Radial thrust in pumps (d) Stuffing Box

Last Answer : (b) Difference in pressure between suction and delivery ends

Propeller type centrifugal pumps are most suitable for (A) High capacity at high heads (B) High capacity at low heads (C) Low capacity at high heads (D) Low capacity at low heads

Description : Propeller type centrifugal pumps are most suitable for (A) High capacity at high heads (B) High capacity at low heads (C) Low capacity at high heads (D) Low capacity at low heads

Last Answer : (B) High capacity at low heads

Why The Centrifugal Pump Is Called High Discharge Pump?

Description : Why The Centrifugal Pump Is Called High Discharge Pump?

Last Answer : Centrifugal pump is a kinetic device. The centrifugal pump uses the centrifugal force to push out the fluid. So the liquid entering the pump receives kinetic energy from the rotating impeller. The centrifugal ... following formulae: Centrifugal force F= (M*V2)/R. Where, M-Mass V-Velocity R-Radius

Volute type of casing is provided in a centrifugal pump to (A) Convert velocity head to pressure head (B) Convert pressure head to velocity head (C) Reduce the discharge fluctuation (D) Increase the discharge

Description : Volute type of casing is provided in a centrifugal pump to (A) Convert velocity head to pressure head (B) Convert pressure head to velocity head (C) Reduce the discharge fluctuation (D) Increase the discharge

Last Answer : (D) Increase the discharge

Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) NPSH required (B) BHP required by the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Check in a centrifugal pump is (A) Provided in the discharge line (B) Generally a globe valve (C) Provided to prevent liquid from backing up through the pump when the pump is turned off or accidently stops running (D) All (A), (B) and (C)

Description : Check in a centrifugal pump is (A) Provided in the discharge line (B) Generally a globe valve (C) Provided to prevent liquid from backing up through the pump when the pump is turned off or accidently stops running (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Check valve provided in the discharge line of a centrifugal pump serves the purpose of controlling the (A) Back flow of fluid in the event of stoppage of pump (B) Discharge pressure (C) Flow of liquid during operation of the pump (D) All (A), (B) and (C)

Description : Check valve provided in the discharge line of a centrifugal pump serves the purpose of controlling the (A) Back flow of fluid in the event of stoppage of pump (B) Discharge pressure (C) Flow of liquid during operation of the pump (D) All (A), (B) and (C)

Last Answer : (A) Back flow of fluid in the event of stoppage of pump

If the discharge of a centrifugal pump is throttled, then its suction lift (A) Increases (B) Decreases (C) Remains unchanged (D) Data insufficient to predict

Description : If the discharge of a centrifugal pump is throttled, then its suction lift (A) Increases (B) Decreases (C) Remains unchanged (D) Data insufficient to predict

Last Answer : (A) Increases

The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor pressure of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Description : The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor ... of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Last Answer : (C) Suction minus vapor pressure of the liquid at suction temperature