List any two ratings of digital input and digital output module each.

List any two ratings of digital input and digital output module each.
by

1 Answer

Answer :

Ratings of Digital Input Module: i) Rated voltage & current: +24V DC at 4mA/120V AC at 6mA/230V AC at 9mA ii) Specified operational voltage range: 0-30V DC/ 264V AC. iii) Absolute maximum input voltage: +35V DC for 0.5sec. iv) Signal Delay: 5.0 msec for DC/ 15 msec for AC ON to OFF or OFF to ON. v) Logic 1: 15V DC at 2.5mA/ 79V AC at 2.5mA. vi) Logic 0: 5V DC at 1mA/ 20V AC at 1mA. 


Ratings of Digital Output Module: i) Rated voltage: +24V DC/+24VDC or 250V AC relay type/120V/230V AC ii) Voltage range: 20.4-28.8V DC/5-30V DC or 5-250VAC relay type/40-264V AC iii) Logic 1: 20V DC min./ 24VDC or 250V AC/120V/230V AC iv) Logic 0: 0.1V DC max./0 VDC or AC/0VAC v) Rated current/point: 0.75A DC/ 2A for relay type/0.5A AC vi) Rated current/common: 6A DC/8A for relay type/0.5A AC

by

Related questions

Draw a block diagram of digital output module of PLC.

Description : Draw a block diagram of digital output module of PLC.

Last Answer : Block diagram of digital output module of PLC:

State any two input and output devices of PLC

Description : State any two input and output devices of PLC

Last Answer : Input Devices of PLC: i) Selector switches ii) Push buttons iii) Binary encoders iv) Mechanical/magnetic Limit switches v) Inductive/ capacitive/optical proximity switches vi) Analog transducers ... /Lamps v) Solenoids vi) Continuous/ discrete valves vii)Analog/digital indicators/recorders etc.

The following box denotes? a) Decision b) Input/Output c) Process d) Module

Description : The following box denotes? a) Decision b) Input/Output c) Process d) Module

Last Answer : Answer: a Explanation: The answer is decision. Conditions are given in this box and then the result is checked accordingly if the condition is true or false.

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

What is the purpose of either 'setpoint module' (6000F090/030) shown in the illustration? EL-0094 A. Program the 'signal conditioner' as to how to vary its input. B. Supply 0 - 10 volts to the 'signal conditioner'. C. Initiate logging of measured information at set intervals; for example, each hour. D. Obtain an input from the 'signal conditioner' and, if outside set limits, signals the 'annunciator'.

Description : What is the purpose of either 'setpoint module' (6000F090/030) shown in the illustration? EL-0094 A. Program the 'signal conditioner' as to how to vary its input. B. Supply 0 - 10 volts to ... . Obtain an input from the 'signal conditioner' and, if outside set limits, signals the 'annunciator'.

Last Answer : Answer: D

Draw the block diagram of discrete input module & explain each block.

Description : Draw the block diagram of discrete input module & explain each block.

Last Answer : Power conversion: It consists of rectifier which converts the incoming AC signal to a pulsating dc level, which is passed through filter and other logic in order to deliver a clean and denounced dc ... Logic section: It passes the input signal to the module s input address LED and the CPU.

One method of troubleshooting digital circuits in a console is to ___________. A. supply alternate logic levels at the input(s) and test for change of state conditions at the output B. ground all inputs and test for a logic '1' at the output C. open all inputs and test for a logic '0' at the output D. vary each input smoothly from 0-10 volts and test for similar variance at the output

Description : One method of troubleshooting digital circuits in a console is to ___________. A. supply alternate logic levels at the input(s) and test for change of state conditions at the output B. ground all ... output D. vary each input smoothly from 0-10 volts and test for similar variance at the output

Last Answer : Answer: A

List any two advantages and any two disadvantages of PLC.

Description : List any two advantages and any two disadvantages of PLC.

Last Answer : Advantages of PLC: i) Increased productivity ii) Increased product quality iii) Increased flexibility and convertibility iv) Reduced manpower v) Reduced cost of product vi) Better inventory control vii) Increased ... v) PLCs are not very good at handling large amount of data, or complex data.

List types of timers.

Description : List types of timers.

Last Answer : Types of Timers: Retentive Timers: 1. ON Delay 2. OFF Delay Non Retentive Timers: 1. ON Delay 2. OFF Delay

List types of memory. Explain any one type of memory in brief.

Description : List types of memory. Explain any one type of memory in brief.

Last Answer : Types of Memories in PLC:  i) Executive Memory  ii) Scratch Pad Memory  iii) Data Table a) Input image memory b) Output image Memory c) Internal bits/ registers/ words  ... storage for programmed instructions entered by the user. The user program area also stores the control program.

List any four names of optial sensors

Description : List any four names of optial sensors

Last Answer : Optial sensors: i) Photodiodes ii) Phototransistors iii) LDRs iv) Photovoltaic cells v) Optical encoder vi) Scintillation counter vii) Photoionization detector viii) Photographic plates

List applications of servomotor.

Description : List applications of servomotor.

Last Answer : Applications of Servomotor: 1) Computers 2) Robotics and toys 3) CD/DVD players 4) Textile industries 5) Instrument servos 6) Tracking and guidance system 7) Self-balancing recorders 8 ... 9) Process controllers 10) Electromechanical actuators 11) Air-craft control system 12) Programming device

An important characteristic of the device shown in figure 'B' of the illustration as compared with conventional NPN or PNP transistors is its ____________. EL-0065 A. higher temperature sensitivity B. higher power ratings C. very high input resistance D. all of the above

Description : An important characteristic of the device shown in figure 'B' of the illustration as compared with conventional NPN or PNP transistors is its ____________. EL-0065 A. higher temperature sensitivity B. higher power ratings C. very high input resistance D. all of the above

Last Answer : Answer: C

BEE Energy efficiency ratings are based on a) Savings in cost c) savings in electricity consumption b) Savings in input d) savings in machinery

Description : BEE Energy efficiency ratings are based on a) Savings in cost c) savings in electricity consumption b) Savings in input d) savings in machinery

Last Answer : savings in electricity consumption

If Relay #5 changed contact position grounding the 'auto' input to the 'pitch controller module', pitch control would be effected by the _________________. EL-0095 A. pitch feedback potentiometer B. Engine room thrust split potentiometer C. Engine room thrust lever only D. Bridge thrust lever only

Description : If Relay #5 changed contact position grounding the 'auto' input to the 'pitch controller module', pitch control would be effected by the _________________. EL-0095 A. pitch feedback potentiometer B. Engine room thrust split potentiometer C. Engine room thrust lever only D. Bridge thrust lever only

Last Answer : Answer: B

What is the purpose of the 'annunciator module' (6000F35) shown in the illustration? EL-0094 A. Provide an input to the setpoint module. B. Drive the alarm lamp and, through the controller, the horn. C. Deliver +5 and +24 volts to their respective power supplies. D. Connect 24 volts to both sides of the horn.

Description : What is the purpose of the 'annunciator module' (6000F35) shown in the illustration? EL-0094 A. Provide an input to the setpoint module. B. Drive the alarm lamp and, through the controller, the horn. ... and +24 volts to their respective power supplies. D. Connect 24 volts to both sides of the horn.

Last Answer : Answer: B

Why input transformer of PUPS module 1 is delta-delta and module 2 is delta-star?

Description : Why input transformer of PUPS module 1 is delta-delta and module 2 is delta-star?

Last Answer : With the help of this arrangement, combined DC output from both chargers is equivalent to that from a 12-pulse rectifier. Advantage of 12-pulse rectifier is that the mains current is fairly close ... phase angle difference 30-degree between module 1 output and module 2 output give 12-pulse output. 

Draw and explain analog input module of PLC.

Description : Draw and explain analog input module of PLC.

Last Answer : Analog input module are used for supplying analog input signal to PLC. Analog signals are generated by transducers, potentiometers. PLCs analog input module consists of analog-to-digital converter (ADC). ... of PLC. PLC reads the binary number and takes further decision based on the required logic 

Output comparators are used in (A) static testing of single module (B) dynamic testing of single module (C) static testing of single and multiple module (D) dynamic testing of single and multiple module

Description : Output comparators are used in (A) static testing of single module (B) dynamic testing of single module (C) static testing of single and multiple module (D) dynamic testing of single and multiple module

Last Answer : (D) dynamic testing of single and multiple module

Draw typical wiring details & four specifications of AC output module of PLC.

Description : Draw typical wiring details & four specifications of AC output module of PLC.

Last Answer : The below figure show the basic field wiring for digital 120V AC output module. The Wiring diagrams show how wires of output devices are connected to screw terminals of PLC modules. As per the wiring ... excessive current from damaging the wiring to the field devices.  Specifications:-

Design a digital circuit which has one input two output and one select line input should be 1000khz output should be 500khz and 250Khz select line either 0 or 1 if 0 select 250khz if 1 select 500khz

Description : Design a digital circuit which has one input two output and one select line input should be 1000khz output should be 500khz and 250Khz select line either 0 or 1 if 0 select 250khz if 1 select 500khz

Last Answer : Ans-demux is the circuit which satisfies the given requirement if 0 is given to the selectline 250khz o/p is provided else 500khz o/p is provided.

In analog computer A) Input is first converted to digital form B) Input is never converted to digital form C) Output is displayed in digital form D) All of the above

Description : In analog computer A) Input is first converted to digital form B) Input is never converted to digital form C) Output is displayed in digital form D) All of the above

Last Answer : Answer : B

In analog computer a. Input is first converted to digital form b. Input is never converted to digital form c. Output is displayed in digital form d. All of above

Description : In analog computer a. Input is first converted to digital form b. Input is never converted to digital form c. Output is displayed in digital form d. All of above

Last Answer : All of above

_______sent data or instructions to the computer: a) Digital b) Output c) Input d) None of The Above

Description : _______sent data or instructions to the computer: a) Digital b) Output c) Input d) None of The Above

Last Answer : c) Input

In analog computer a. Input is first converted to digital form b. Input is never converted to digital form c. Output is displayed in digital form d. All of above

Description : In analog computer a. Input is first converted to digital form b. Input is never converted to digital form c. Output is displayed in digital form d. All of above

Last Answer : b. Input is never converted to digital form

In analog computer a. Input is first converted to digital form b. Input is never converted to digital form c. Output is displayed in digital form d. All of above

Description : In analog computer a. Input is first converted to digital form b. Input is never converted to digital form c. Output is displayed in digital form d. All of above

Last Answer : b. Input is never converted to digital form

Where is there a list of ratings for local fitness centers in Texas?

Description : Where is there a list of ratings for local fitness centers in Texas?

Last Answer : If you want to find anything around your location you can use a simple technique. You enter your location in Google maps (maps.google.com). Then you press the button that says 'search nearby' and use the ... . Since Texas is a very large state we can't know how to rate those in an unknown location.

List any four input and four output devices used with PLC.

Description : List any four input and four output devices used with PLC.

Last Answer : Input device: 1. Push button. 2. Temperature switches. 3. Limit switches. 4. Pressure switches. 5. Level Switches. 6. Proximity Switches. Output devices: 1. Motor. 2. Display. 3. Heater coil. 4. Relay. 5. Lamp. 6. Buzzer.

List any our input and output of PLC.

Description : List any our input and output of PLC.

Last Answer : Typical PLC inputs  1) Push Button  2) Selector Switch  3) Proximity switch  4) FOOT switch, level switch  5) Analog input  Typical PLC outputs  1) Contactor Coil, solenoid, relay  2) Indicating Lamp  3) Buzzer  4) Alaram annunciator

List typical inputs and outputs for PLC (four input and any four output).

Description : List typical inputs and outputs for PLC (four input and any four output).

Last Answer : Typical PLC inputs  Push Button  Selector Switch  Proximity switch  FOOT switch, level switch  Analog input  Typical PLC outputs  Contactor Coil, solenoid, relay  Indicating Lamp  Buzzer  Alaram annunciator

Differentiate between two-wire and three-wire control

Description : Differentiate between two-wire and three-wire control

Last Answer : Two-Wire Control  Three-Wire Control 1 The control component offers only two-wires for its connection in control circuit. The control components offer threewires for their connection in control ... using starter. The safe starting ensures the Novolt protection.  4

Explain count up (CTU) instruction with timing diagram.

Description : Explain count up (CTU) instruction with timing diagram.

Last Answer : The CTU is an instruction that counts false-to-true rung transitions. Rung transitions can be caused by events occurring in the program. When rung conditions for a CTU instruction have made a false-to-true ... of Counter up(CTU) Instruction: Too many uploads - please try again in an hour

Write the ladder program for 24 hour clock.

Description : Write the ladder program for 24 hour clock.

Last Answer : Ladder Program for 24 hour clock:

State the function of PLC memory w.r.t. types, speed of execution.

Description : State the function of PLC memory w.r.t. types, speed of execution.

Last Answer : PLC memory cab be divided into two major types: 1) System memory: a) Executive Memory: The executive is a permanently stored collection of programs that are considered part of the system itself. ... RAM memory is fastest amongst all type of memory. Flash ROM memory is faster than ROM memory. 

Develop the control circuit for star-delta starter used for starting a 3 ∅ induction motor.

Description : Develop the control circuit for star-delta starter used for starting a 3 ∅ induction motor.

Last Answer : Control Circuit for Star-Delta Starter: 1) Automatic Star-Delta Starter: OR 2) Semi- automatic Star-Delta Starter:

Give the full form of SCADA & HMI.

Description : Give the full form of SCADA & HMI.

Last Answer : Full Form of SCADA and HMI:  SCADA:-Supervisory Control and Data Acquisition  HMI :- Human Machine Interface

State the function of seal in circuit w.r.t. PLC.

Description : State the function of seal in circuit w.r.t. PLC.

Last Answer : Standard Start-Stop-Seal circuit:  * The Start-Stop-Seal circuit is as shown in figure. The power circuit consists of 3ph load (Motor) connected by a main contactor (M) to 3-phase supply. The ... * When STOP is pressed, M gets de-energized and motor gets disconnected from supply.

Draw the block diagram of PLC.

Description : Draw the block diagram of PLC.

Last Answer : Block diagram of PLC and input/output devices used for PLC Input/output devices - The input module has bank of terminals for physically connecting input devices, like push buttons, limit switches etc. ... is to translate signals from the PLC's CPU into a form that the output device can use.

State the need of automation.

Description : State the need of automation. 

Last Answer : Need of Automation in Process : * To fulfill the demand of product at right time. * To reduce the human errors and involvement of human being in the process. * For better productivity. * For better ... of process. * For better quality. * For reducing man power. * For reducing cost of product.

Draw block diagram of PID controller

Description : Draw block diagram of PID controller

Last Answer : Block diagram of PID Controller:

Develop power and control diagram for secondary frequency acceleration starter of slip ring induction motor.

Description : Develop power and control diagram for secondary frequency acceleration starter of slip ring induction motor. 

Last Answer : Power and Control Circuit diagram for secondary frequency acceleration starter of slip ring induction motor:

Explain UP counter instruction of PLC with suitable instruction.

Description : Explain UP counter instruction of PLC with suitable instruction.

Last Answer : The CTU is an instruction that counts false-to-true rung transitions. Rung transitions can be caused by events occurring in the program. When rung conditions for a CTU instruction have made a false-to-true ... accumulated count to zero. Counting can resume when rung 4 goes false again.

Explain pressure actuated switch with neat constructional diagram.

Description : Explain pressure actuated switch with neat constructional diagram.

Last Answer : Pressure actuated switch: A pressure actuated switch is a device designed to monitor a process pressure and provide an output when a set pressure (setpoint) is reached. A pressure actuated switch does this by ... range spring (e.g. if the nt is turned clockwise the trip pressure will be higher). 

Differentiate between power and control wiring

Description : Differentiate between power and control wiring

Last Answer : Power wiring Control wiring 1 Used for connecting load to main power supply through appropriate switchgear and protecting devices such as overload relay contacts Used for ... can be used for connecting control circuit as control circuit does not carry higher current.

Draw construction of DC servomotor.

Description : Draw construction of DC servomotor. 

Last Answer : DC servomotor:

Draw power and control circuit for definite time-limit starter for slip-ring induction motor. Explain its working.

Description : Draw power and control circuit for definite time-limit starter for slip-ring induction motor. Explain its working.

Last Answer : Definite Time-limit Starter for Slip-ring Induction Motor: This starter is used for automatic control of acceleration of slip-ring induction motor at the time of starting. In this starter, the ... each phase, shorting the rotor winding terminals and final acceleration of the motor takes place. 

Draw block diagram of proportional controller.

Description : Draw block diagram of proportional controller.

Last Answer : Block diagram of Proportional Controller:

Draw ladder diagram for following sequence: i) When NO START Pushbutton is pressed Green light is on. ii) When NC STOP Pushbutton is pressed Red light is on. Green light goes off.

Description : Draw ladder diagram for following sequence: i) When NO START Pushbutton is pressed Green light is on. ii) When NC STOP Pushbutton is pressed Red light is on. Green light goes off.

Last Answer : ladder diagram