Draw typical wiring details & four specifications of AC output module of PLC.

Draw typical wiring details & four specifications of AC output module of PLC.
by

1 Answer

Answer :

The below figure show the basic field wiring for digital 120V AC output module. The Wiring diagrams show how wires of output devices are connected to screw terminals of PLC modules. As per the wiring diagram, User has to connect the wires of input and output devices to PLC or Module. It can be thought of as a simple switch power can be provided to control the output device. During normal operation, processor sends the output state that was determined by logic diagram of output module. The module then switches the power to the field devices. A fuse is normally provided in that the output circuit of the module to prevent excessive current from damaging the wiring to the field devices. 

image

Specifications:-

image

by

Related questions

Draw a block diagram of digital output module of PLC.

Description : Draw a block diagram of digital output module of PLC.

Last Answer : Block diagram of digital output module of PLC:

List any four input and four output devices used with PLC.

Description : List any four input and four output devices used with PLC.

Last Answer : Input device: 1. Push button. 2. Temperature switches. 3. Limit switches. 4. Pressure switches. 5. Level Switches. 6. Proximity Switches. Output devices: 1. Motor. 2. Display. 3. Heater coil. 4. Relay. 5. Lamp. 6. Buzzer.

List & explain the timer instruction of PLC. Draw the ladder diagram to verify (i) OR gate& (ii) NOR gate logic

Description : List & explain the timer instruction of PLC. Draw the ladder diagram to verify (i) OR gate& (ii) NOR gate logic 

Last Answer : Depending on the time delay and operation, there are two types of timers  * PLC timer- (i) ON delay timer  (ii) OFF delay timer Description (i) ON delay timer 1) This instruction counts time interval when ... a) OR gate ladder diagram y = A + B b)NOR gate ladder diagram

Draw and explain analog input module of PLC.

Description : Draw and explain analog input module of PLC.

Last Answer : Analog input module are used for supplying analog input signal to PLC. Analog signals are generated by transducers, potentiometers. PLCs analog input module consists of analog-to-digital converter (ADC). ... of PLC. PLC reads the binary number and takes further decision based on the required logic 

Draw the block diagram of discrete input module & explain each block.

Description : Draw the block diagram of discrete input module & explain each block.

Last Answer : Power conversion: It consists of rectifier which converts the incoming AC signal to a pulsating dc level, which is passed through filter and other logic in order to deliver a clean and denounced dc ... Logic section: It passes the input signal to the module s input address LED and the CPU.

List typical inputs and outputs for PLC (four input and any four output).

Description : List typical inputs and outputs for PLC (four input and any four output).

Last Answer : Typical PLC inputs  Push Button  Selector Switch  Proximity switch  FOOT switch, level switch  Analog input  Typical PLC outputs  Contactor Coil, solenoid, relay  Indicating Lamp  Buzzer  Alaram annunciator

Historically, Knox PLC sold industrial clamps directly to firms using these items in their production process. Knox's Chairman believes that it may be time to start using an industrial distributor because of the ability of such firms to: A)provide Knox with market information. B)supply technical information to Knox. C)provide customers with more competitive pricing. D)carry a more complete line of Knox clamps. E)market the products to Knox specifications.

Description : Historically, Knox PLC sold industrial clamps directly to firms using these items in their production process. Knox's Chairman believes that it may be time to start using an industrial distributor because ... D)carry a more complete line of Knox clamps. E)market the products to Knox specifications.

Last Answer : A)provide Knox with market information.

Explain the need of PLC in automation.

Description : Explain the need of PLC in automation.

Last Answer : Need of PLC in automation * To reduce human efforts. * To get maximum efficiency from machine and control them with human logic * To reduce complex circuitry of entire system * To eliminate ... in working conditions. * Fast and Easily programmed and have an easily understood programming language. 

Describe in brief memory organization of PLC.

Description : Describe in brief memory organization of PLC.

Last Answer : Different types of memory that are generally used in PLC s are as follows: 1. RAM: 2. ROM A.)EPROM B.)EEPROM  In PLC program instructions are stored in the ... is carried out and stored. User memory consists of program files or register table and holds the complete operation.

Define with respect to PLC i) scanning cycle ii) speed of execution.

Description : Define with respect to PLC i) scanning cycle ii) speed of execution.

Last Answer : Scanning Cycle * It is number of states/steps which the controller follows when it is put in RUN mode. * It is also called as operating cycle and is defined as the number of states ... is referred as a speed of execution. Higher CPU speeds provide faster performance that shortens task time. 

Give the classification of PLC. Explain modular PLC in brief.

Description : Give the classification of PLC. Explain modular PLC in brief. 

Last Answer : CLASSIFICATION OF PLC PLC can be classified as follows 1.According to structure of PLC a. Integral type b. Modular Type 2. Depending upon the no. of I/Os a. Small( ... easy to assemble, easy expansion and maintenance. * Large and medium-sized PLC generally use the modular structure. 

Draw the block diagram of PLC.

Description : Draw the block diagram of PLC.

Last Answer : Block diagram of PLC and input/output devices used for PLC Input/output devices - The input module has bank of terminals for physically connecting input devices, like push buttons, limit switches etc. ... is to translate signals from the PLC's CPU into a form that the output device can use.

Draw and explain schematic of PLC based automatic car parking barrier system.

Description : Draw and explain schematic of PLC based automatic car parking barrier system.

Last Answer : Explanation: Automatic car parking system allow to park maximum numbers of car in parking zone according to size of parking zone. parking zone number of vehicle parked in parking zone is less ... available parking space then automated parking system does not allow enter next car in parking zone. 

Draw the block diagram for PLC power supply and explain the function of each block.

Description : Draw the block diagram for PLC power supply and explain the function of each block.

Last Answer : PLC power supply generates the required dc voltage levels for operation of the internal circuit of PLC. It is a switched mode power supply which accepts wide range of AC/ DC input ... of power failure from AC input, Battery backup becomes active and prevents accidental shut down of PLC

Draw a neat labelled diagram of PLC. Explain the function of each block.

Description : Draw a neat labelled diagram of PLC. Explain the function of each block.

Last Answer : Block Diagram of PLC:-  A simplified block diagram of a PLC shown in above Fig. It has three major units/sections.  I/O (Input/Output) Modules.  CPU (Central ... membrane keypad for program entry, and a display device (LED or LCD) for viewing program steps of functions. 

What are different standard test inputs? Draw them & give their Laplace representation.

Description : What are different standard test inputs? Draw them & give their Laplace representation.

Last Answer : Standard test input signals - 1. Step input signal 2. Ramp input signal 3. Parabolic input signal 4. Impulse input signal

Drawthe PLC ladder diagram of ON-OFF control of lamp. Write the input and output devises.

Description : Drawthe PLC ladder diagram of ON-OFF control of lamp. Write the input and output devises.

Last Answer : Diagram:

State any two input and output devices of PLC

Description : State any two input and output devices of PLC

Last Answer : Input Devices of PLC: i) Selector switches ii) Push buttons iii) Binary encoders iv) Mechanical/magnetic Limit switches v) Inductive/ capacitive/optical proximity switches vi) Analog transducers ... /Lamps v) Solenoids vi) Continuous/ discrete valves vii)Analog/digital indicators/recorders etc.

List any our input and output of PLC.

Description : List any our input and output of PLC.

Last Answer : Typical PLC inputs  1) Push Button  2) Selector Switch  3) Proximity switch  4) FOOT switch, level switch  5) Analog input  Typical PLC outputs  1) Contactor Coil, solenoid, relay  2) Indicating Lamp  3) Buzzer  4) Alaram annunciator

Consider a continuous-time system with input x(t) & output y(t) are related by y(t) = x (sin t). This system is

Description : Consider a continuous-time system with input x(t) & output y(t) are related by y(t) = x (sin t). This system is (A) causal & linear (B) non-causal & linear (C) causal & non-linear (D) non-causal & non-linear

Last Answer : Consider a continuous-time system with input x(t) & output y(t) are related by y(t) = x (sin t). This system is non-causal & linear

The +5 volt regulated power supply shown in the illustration is fed directly from the _______________. EL-0094 A. 115 volt AC bus B. Annunciator Module C. +24 volt supply D. Annunciator Controller

Description : The +5 volt regulated power supply shown in the illustration is fed directly from the _______________. EL-0094 A. 115 volt AC bus B. Annunciator Module C. +24 volt supply D. Annunciator Controller

Last Answer : Answer: C

Wiring up an AC Motor?

Description : Wiring up an AC Motor?

Last Answer : black should be your ground Red will come from your live power Yellows to the opener button

State significance of earthing. Draw and explain pipe earthing. State the values of earth resistances for : (i) Substation (ii) Residential wiring (iii) H.T. Line (iv) L.T. Line

Description : State significance of earthing. Draw and explain pipe earthing. State the values of earth resistances for : (i) Substation (ii) Residential wiring (iii) H.T. Line (iv) L.T. Line

Last Answer : Significance of earthing:  * Earthing means connecting the body of the electrical equipment (it means the part which does not carries current under normal condition) to the earth. For example electrical equipment' ... surrounded by charcoal and salt.  the values of earth resistances for: 

Draw the wiring diagram of fluorescent tube. Explain the working of choke and starter.

Description : Draw the wiring diagram of fluorescent tube. Explain the working of choke and starter. 

Last Answer : Fluorescent lamp:- Operation:- When switch is ON current flows through the choke-filament no1- starter-filament no. 2- to neutral, At that time choke induces high voltage which is applied to ... at the time of starting. ii) Starter: To make and break the circuit to start the tube. 

Draw block diagram of function generator and list two specifications of it.

Description : Draw block diagram of function generator and list two specifications of it. 

Last Answer : Specifications: 1. Output- Square wave , sine wave, Triangular, TTL pulse 2. Frequency Ranges- 0.1 Hz to 11 MHz, up/down range switchable in eight decade steps 3. Dial Range-1 to 11 calibrated 0.1 to 1 uncalibrated 4. Pulse and Ramp Aspect Ratio-95:5

Draw pin diagram of ATX power supply. Give specifications of each pin.

Description : Draw pin diagram of ATX power supply. Give specifications of each pin.

Last Answer : -12V Used in some types of serial port circuits -5V Used for floppy controllers 0V Ground +3.3V Used in many of the new CPUs, system memory, AGP video cards Power Good Signal (PW-OK) The computer ... special circuits even when SMPS is off PS-ON is an input to SMPS only when the signal is low.

The following box denotes? a) Decision b) Input/Output c) Process d) Module

Description : The following box denotes? a) Decision b) Input/Output c) Process d) Module

Last Answer : Answer: a Explanation: The answer is decision. Conditions are given in this box and then the result is checked accordingly if the condition is true or false.

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

Output comparators are used in (A) static testing of single module (B) dynamic testing of single module (C) static testing of single and multiple module (D) dynamic testing of single and multiple module

Description : Output comparators are used in (A) static testing of single module (B) dynamic testing of single module (C) static testing of single and multiple module (D) dynamic testing of single and multiple module

Last Answer : (D) dynamic testing of single and multiple module

List any two ratings of digital input and digital output module each.

Description : List any two ratings of digital input and digital output module each.

Last Answer : Ratings of Digital Input Module: i) Rated voltage & current: +24V DC at 4mA/120V AC at 6mA/230V AC at 9mA ii) Specified operational voltage range: 0-30V DC/ 264V AC. iii) Absolute maximum input voltage: + ... / 2A for relay type/0.5A AC vi) Rated current/common: 6A DC/8A for relay type/0.5A AC

The computer needs additional components called _______ to accomplish its input, output and storage functions: a) mice b) specifications c) architecture d) peripheral e) None of these

Description : The computer needs additional components called _______ to accomplish its input, output and storage functions: a) mice b) specifications c) architecture d) peripheral e) None of these

Last Answer : d) peripheral

We use the output of the requirement analysis, the requirement specification as the input for writing :- a) User Acceptance Test Cases b) Integration Level Test Cases c) Unit Level Test Cases d) Program specifications

Description : We use the output of the requirement analysis, the requirement specification as the input for writing :- a) User Acceptance Test Cases b) Integration Level Test Cases c) Unit Level Test Cases d) Program specifications

Last Answer : a) User Acceptance Test Cases

(i) List and explain the types of ROM. (ii) List any four advantages of PLC.

Description : (i) List and explain the types of ROM.  (ii) List any four advantages of PLC.

Last Answer : ROM types  1) PROM  2) EPROM  3) EEPROM  1) PROM: - (Programmable Read Only Memory): In this memory it may be programed once and once only, by the user/programmer. The user than programs ... signals.  10) PLC can provide security for ladder programming.  11) Speed of PLC is in milliseconds.

Draw the labeled block diagram of process control system and explain each block.

Description : Draw the labeled block diagram of process control system and explain each block.

Last Answer : Explanation - Process control system consists of process or plant, sensor, error detector, automatic Controller, actuator or control element. 1) Process or plant- process means some manufacturing sequence ... process which changes the process variable. Output of this block is denoted by u .

Define servo system. Draw the block diagram of DC Servo System.

Description : Define servo system. Draw the block diagram of DC Servo System.

Last Answer : Definition: Servo system is defined as automatic feedback control system working on error signals giving the output as mechanical position, velocity or acceleration.  1) The servo system consists of error ... , DC motor, DC gear system and the DC load whose position is to be changed. 

What is the difference between DCS & PLC & SCADA ?

Description : What is the difference between DCS & PLC & SCADA ?

Last Answer : Ans-PLC stands for Programmable Logic ControllerDCS for Data control SystemSCADA for Supervisory Control And Data Acquisition SCADA involves supervision by a user in most cases the plant controller.Whereas PLC ... ystem already in it but for PLC sydtem addition all SCADA software must be provided.

Differentiate between RAM & ROM in PLC memory

Description : Differentiate between RAM & ROM in PLC memory

Last Answer : RAM ROM Random access memory Read Only memory Used for storing temporary data Used for storing fixed data such as programs Data is lost when power is removed Data is retained in case of power loss  Read write speed is quite faster Write operation is slow

Explain the function of ROM & RAM memory of PLC.

Description : Explain the function of ROM & RAM memory of PLC. 

Last Answer : Read Only Memory (ROM) is used by PLC for storing operating system. The operating system is programmed by the manufacturer.  Random access memory (RAM) is a Read Write memory and used by ... store temporary data like status of I/O pins, temporary results of calculations, timer counter values etc.

In a closed-loop system in which the output is the speed of a motor, the output rate control can be used to_________.

Last Answer : In a closed-loop system in which the output is the speed of a motor, the output rate control can be used to limit the acceleration of the motor.

A phase lag lead network introduces in the output?

Description : A phase lag lead network introduces in the output?

Last Answer : A phase lag lead network introduces in the output lag at low frequencies and lead at high frequencies.

If a step function is applied to the input of a system and the output...

Description : If a step function is applied to the input of a system and the output remains below a certain level for all the time, the system is?

Last Answer : If a step function is applied to the input of a system and the output remains below a certain level for all the time, the system is not necessarily stable.

In a control system the output of the controller is given to?

Description : In a control system the output of the controller is given to?

Last Answer : In a control system the output of the controller is given to final control element.

The output of a feedback control system must be a function of?

Description : The output of a feedback control system must be a function of?

Last Answer : The output of a feedback control system must be a function of reference and output.

Any externally introduced signal affecting the controlled output is called a?

Description : Any externally introduced signal affecting the controlled output is called a?

Last Answer : Any externally introduced signal affecting the controlled output is called a stimulus.

The initial response when the output is not equal to input is called?

Description : The initial response when the output is not equal to input is called?

Last Answer : The initial response when the output is not equal to input is called Transient response.

A control system in which the control action is somehow dependent on the output is known as

Description : A control system in which the control action is somehow dependent on the output is known as?

Last Answer : A control system in which the control action is somehow dependent on the output is known as Closed loop system.

List any four wiring accessories and its function.

Description : List any four wiring accessories and its function. 

Last Answer : Following wiring accessories: 1) Lamp holder: It is the holding accessory. The different types of holders used such as angle holder, batten holder, pendent holder 2) Ceiling Rose: Ceiling rose are of two types: ... etc 9) Switch board, ICDP Main Switch 10) All types of size of VIR & PVC wire

Write the specifications of I.C. engine used in a two wheeler four stroke vehicle.

Description : Write the specifications of I.C. engine used in a two wheeler four stroke vehicle.

Last Answer : Engine specifications for two wheeler 1. Engine of Bajaj Discover 125 ST - Air-cooled, 4-stroke 124.6 cc engine - Maximum power of 12.8 Bhp at 9000 rpm - Maximum torque of 11 Nm at 7000 rpm OR 2. Honda Livo a) BS- ... rpm. d) Bore x Stroke - 50 x 55.6 mm e) C R - 9.9 : 1, Max Speed - 86KMPH

List four specifications of function generator.

Description : List four specifications of function generator. 

Last Answer : Specifications: 1. Output- Square wave , sine wave, Triangular, TTL pulse 2. Frequency Ranges- 0.1 Hz to 11 MHz, up/down range switchable in eight decade steps 3. Dial Range-1 to 11 calibrated 0.1 to 1 uncalibrated 4. Pulse and Ramp Aspect Ratio-95:5