Which of the following refers to theterms "residual error rate"? A. the number of biterrors per twenty four hours of continuous operation onanasynchronous line B. The probability that one or moreerrors will be undetected whenan error detection scheme is used C. the probability thatone or more errors will bedetected when anerror detection mechanism is used D. signal tonoise ratio dividedby the ratio of energy perbit to noise per hertz E. None of the above

Which of the following refers to theterms "residual error rate"?
A.
the number of biterrors per twenty four hours of continuous operation onanasynchronous line
B.
The probability that one or moreerrors will be undetected whenan error detection scheme is used
C.
the probability thatone or more errors will bedetected when anerror detection mechanism is used
D.
signal tonoise ratio dividedby the ratio of energy perbit to noise per hertz
E.
None of the above
by

1 Answer

Answer :

The probability that one or moreerrors will be undetected whenan error detection scheme is used
by

Related questions

The probability thata singlebit will be inerror on a typical public telephone lineusing 4800 bps modem is 10 to the power -3. If no error detection mechanism is used, the residual error ratefor a communicationline using 9-bit frames is approximately equal to A. 0.003 B. 0.009 C. 0.991 D. 0.999 E. None of the above

Description : The probability thata singlebit will be inerror on a typical public telephone lineusing 4800 bps modem is 10 to the power -3. If no error detection mechanism is used, the residual error ratefor a communicationline using 9-bit frames is ... to A. 0.003 B. 0.009 C. 0.991 D. 0.999 E. None of the above

Last Answer : 0.009

Error rate is A. an error-detectingcode based ona summation operation performed onthebits to be checked. B. a checkbit appended to anarrayof binary digits to make thesum of all thebinary digits. C. a code in which each expressionconforms to specific rules of construction, so that if certain errors occur in an expression, the resulting expression will not conform to the rulesof constructionand thus thepresence of the errors isdetected. D. the ratioof the number ofdata units in error to the total number of dataunits E. None of the above

Description : Error rate is A. an error-detectingcode based ona summation operation performed onthebits to be checked. B. a checkbit appended to anarrayof binary digits to make thesum of all thebinary digits. C. a ... ratioof the number ofdata units in error to the total number of dataunits E. None of the above

Last Answer : the ratioof the number ofdata units in error to the total number of dataunits

Define Error Detection and Correction. Mention the types of errors.

Description : Define Error Detection and Correction. Mention the types of errors.

Last Answer : Data can be corrupted during transmission. For reliable communication, errors must be detected and corrected. Single bit error: The only one bit of a given data unit (such as byte character/data unit or packet) is ... error: 2 or more bits in the data unit have changed from 1 to 0 from 0 to 1.

Of the following statements, which best distinguishes ordinary negligence from gross negligence? a. The more material the undetected error the greater the likelihood of ordinary negligence. b. Gross negligence is most probable when the auditor fails to detect errors that occurred under conditions of strong internal control. c. Failure to detect material errors, whether internal control is strong or weak, suggests gross negligence. d. Failure to exercise reasonable care denotes ordinary negligence, whereas failure to exercise minimal care indicates gross negligence

Description : Of the following statements, which best distinguishes ordinary negligence from gross negligence? a. The more material the undetected error the greater the likelihood of ordinary negligence. ... care denotes ordinary negligence, whereas failure to exercise minimal care indicates gross negligence

Last Answer : Failure to exercise reasonable care denotes ordinary negligence, whereas failure to exercise minimal care indicates gross negligence

In an Ethernet local area network, which one of the following statements is TRUE ? a. A station stops to sense the channel once it starts transmitting a frame. b. The purpose of the jamming signal is to pad the frames that are smaller than the minimum frame size. c. A station continues to transmit the packet even after the collision is detected. d. The exponential backoff mechanism reduces the probability of collision on retransmissions

Description : In an Ethernet local area network, which one of the following statements is TRUE ? a. A station stops to sense the channel once it starts transmitting a frame. b. The purpose ... collision is detected. d. The exponential backoff mechanism reduces the probability of collision on retransmissions

Last Answer : The exponential backoff mechanism reduces the probability of collision on retransmissions

Which error detection method consists of just one redundant bit per data unit? A) Simple parity check B) Two-dimensionalparity check C) CRC D) Checksum

Description : Which error detection method consists of just one redundant bit per data unit? A) Simple parity check B) Two-dimensionalparity check C) CRC D) Checksum

Last Answer : Simple parity check

. The _____of errors is more difficult than the ______. A) correction; detection B) detection; correction C) creation; correction D) creation;detection

Description : . The _____of errors is more difficult than the ______. A) correction; detection B) detection; correction C) creation; correction D) creation;detection

Last Answer : correction; detection

To guarantee the detection of up to 5 errors in all cases, the minimum Hamming distance in a block code must be _______ A. 5 B. 6 C. 11 D. none of the above

Description : To guarantee the detection of up to 5 errors in all cases, the minimum Hamming distance in a block code must be _______ A. 5 B. 6 C. 11 D. none of the above

Last Answer : B. 6

Which performance parameter is the minimum amount of optical power required to achieve a specific bit-error rate (BER) in digital systems or a given signal-to-noise ratio (SNR) in analog systems?

Description : Which performance parameter is the minimum amount of optical power required to achieve a specific bit-error rate (BER) in digital systems or a given signal-to-noise ratio (SNR) in analog systems?

Last Answer : Receiver sensitivity.

The auditor's defense of contributory negligence is most likely to prevail when a. Third party injury has been minimal. b. The client is privately held as contrasted with a public company. c. Undetected errors have resulted in materially misleading financial statements. d. The auditor fails to detect fraud resulting from management override of the control structure

Description : The auditor's defense of contributory negligence is most likely to prevail when a. Third party injury has been minimal. b. The client is privately held as contrasted with a public company ... statements. d. The auditor fails to detect fraud resulting from management override of the control structure

Last Answer : The auditor fails to detect fraud resulting from management override of the control structure

The auditor's defense of contributory negligence is most likely to prevail when a. Third party injury has been minimal. b. The client is privately held as contrasted with a public company. c. Undetected errors have resulted in materially misleading financial statements. d. The auditor fails to detect fraud resulting from management override of the control structure.

Description : The auditor's defense of contributory negligence is most likely to prevail when a. Third party injury has been minimal. b. The client is privately held as contrasted with a public company. ... . d. The auditor fails to detect fraud resulting from management override of the control structure.

Last Answer : The auditor fails to detect fraud resulting from management override of the control structure.

Which of the following statements reflects an auditor's responsibility for detecting fraud and error? a. An auditor is responsible for detecting employee errors and simple fraud, but not for discovering fraud involving employee collusion or management overrideAn auditor should design the auditto provide reasonable assurance ofdetecting errors and fraud that arematerial to the financial statements.c. An auditor should plan the audit to detecterrors and fraud that are caused bydepartures from the applicable FRF.d. An auditor is not responsible fordetecting errors and fraud unless theapplication of PSAs and PAPs would resultin such detection

Description : Which of the following statements reflects an auditor's responsibility for detecting fraud and error? a. An auditor is responsible for detecting employee errors and simple fraud, but not for ... detecting errors and fraud unless the application of PSAs and PAPs would result in such detection

Last Answer : An auditor should design the audit to provide reasonable assurance of detecting errors and fraud that are material to the financial statements.

It is the amount or amounts set by the auditor at less than materiality for the financial statements as a whole to reduce to an appropriately low level the probability that the aggregate of uncorrected and undetected misstatements exceeds materiality for the financial statements as a whole. a. Lower materiality b. Lesser materiality c. Performance materiality d. Materiality

Description : It is the amount or amounts set by the auditor at less than materiality for the financial statements as a whole to reduce to an appropriately low level the probability that the aggregate of ... as a whole. a. Lower materiality b. Lesser materiality c. Performance materiality d. Materiality

Last Answer : Performance materiality

In the Ethernet frame, the_______field contains error detection information. A) CRC B) preamble C) address D) none of the above

Description : In the Ethernet frame, the_______field contains error detection information. A) CRC B) preamble C) address D) none of the above

Last Answer : CRC

Which error detection method usesone's complement arithmetic? A) Simple parity check B) Two-dimensionalparity check C) CRC D) Checksum

Description : Which error detection method usesone's complement arithmetic? A) Simple parity check B) Two-dimensionalparity check C) CRC D) Checksum

Last Answer : Checksum

Block coding can help in _______at the receiver. A) Synchronization B) Error detection C) Attenuation D) (a) and (b)

Description : Block coding can help in _______at the receiver. A) Synchronization B) Error detection C) Attenuation D) (a) and (b)

Last Answer : (a) and (b)

Error detection ata data link level is achieved by A. bit stuffing B. cyclic redundancy codes C. Hamming codes D. equalization

Description : Error detection ata data link level is achieved by A. bit stuffing B. cyclic redundancy codes C. Hamming codes D. equalization

Last Answer : cyclic redundancy codes

The layer of OSI model can use the trailer of the frame for error detection. A) Physical B) Data link C) Transport D) Presentation

Description : The layer of OSI model can use the trailer of the frame for error detection. A) Physical B) Data link C) Transport D) Presentation

Last Answer : A) Physical

SSL is not responsible for a. Mutual authentication of client & server b. Secret communication c. Data Integrity protection d. Error detection and correction

Description : SSL is not responsible for a. Mutual authentication of client & server b. Secret communication c. Data Integrity protection d. Error detection and correction

Last Answer : d. Error detection and correction

Which error detection method uses one's complement arithmetic? A. Simple parity check B. Two-dimensional parity check C. CRC D. Checksum

Description : Which error detection method uses one's complement arithmetic? A. Simple parity check B. Two-dimensional parity check C. CRC D. Checksum

Last Answer : D. Checksum

The probability that an auditor's procedures leading to the conclusion that a material error does not exist in an account balance when, in fact, such error does exist is referred to as a. Prevention risk. b. Detection risk. c. Inherent risk. d. Control risk

Description : The probability that an auditor's procedures leading to the conclusion that a material error does not exist in an account balance when, in fact, such error does exist is referred to as a. Prevention risk. b. Detection risk. c. Inherent risk. d. Control risk

Last Answer : Detection risk.

The probability of an auditor's procedures leading to the conclusion that a material error does not exist in an account balance when, in fact, such error does exist is referred to as a. Prevention risk. b. Inherent risk. c. Control risk. d. Detection risk

Description : The probability of an auditor's procedures leading to the conclusion that a material error does not exist in an account balance when, in fact, such error does exist is referred to as a. Prevention risk. b. Inherent risk. c. Control risk. d. Detection risk

Last Answer : b

Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it is assumed that each sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Description : Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it ... sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Last Answer : (C) 128 kbps

The Internet Control Message Protocol (ICMP) A. allows gateways to send error acontrol messages toother gateways or hosts B. provides communication between the Internet Protocol Software on one machine and the InternetProtocol Software on another C. reports error conditions tothe original source, the source must relate errors to individual applicationprograms and takeaction to correct theproblem D. All of theabove E. None of the above

Description : The Internet Control Message Protocol (ICMP) A. allows gateways to send error acontrol messages toother gateways or hosts B. provides communication between the Internet Protocol Software on one machine ... and takeaction to correct theproblem D. All of theabove E. None of the above

Last Answer : All of theabove

_______ can detect burst error of length less than or equal to degree of the polynomial and detects burst errors that affect odd number of bits. a. Hamming Code b. CRC c. VRC d. None of the above

Description : _______ can detect burst error of length less than or equal to degree of the polynomial and detects burst errors that affect odd number of bits. a. Hamming Code b. CRC c. VRC d. None of the above

Last Answer : b. CRC

Carrier is A. One or more conductors that serve as a common connection for a related group of devices B. a continuous frequency capableof being modulated or impressed witha second signal C. the condition whentwo or more sections attempt to use the same channel at the same time D. a collection of interconnected functional units that provides a data communications service among stations attached tothe network E. None of the above

Description : Carrier is A. One or more conductors that serve as a common connection for a related group of devices B. a continuous frequency capableof being modulated or impressed witha second signal C. ... that provides a data communications service among stations attached tothe network E. None of the above

Last Answer : a continuous frequency capableof being modulated or impressed witha second signa

Contention is A. One or more conductors that serve as a common connection for a related group of devices B. a continuous frequency capableof being modulated or impressed witha second signal C. the condition whentwo or more stations attempt to use the same channel at the same time D. a collection of interconnected functional units that provides a data communications service among stations attached tothe network E. None of the above

Description : Contention is A. One or more conductors that serve as a common connection for a related group of devices B. a continuous frequency capableof being modulated or impressed witha second signal C. ... that provides a data communications service among stations attached tothe network E. None of the above

Last Answer : the condition whentwo or more stations attempt to use the same channel at the same time

When does the station B send a positive acknowledgement (ACK) to station A in Stop and Wait protocol? a. only when no error occurs at the transmission level b. when retransmission of old packet in a novel frame is necessary c. only when station B receives frame with errors d. all of the above

Description : When does the station B send a positive acknowledgement (ACK) to station A in Stop and Wait protocol? a. only when no error occurs at the transmission level b. when retransmission of old packet in a novel frame is necessary c. only when station B receives frame with errors d. all of the above

Last Answer : only when no error occurs at the transmission level

The _________Protocol, addsa simple error control mechanism to the _______Protocol. A) Stop-and-Wait ARQ; Stop-and-Wait B) Go-Back-N ARQ; Stop-and-Wait C) Selective Repeat ARQ; Go-Back-N ARQ D) none of the above

Description : The _________Protocol, addsa simple error control mechanism to the _______Protocol. A) Stop-and-Wait ARQ; Stop-and-Wait B) Go-Back-N ARQ; Stop-and-Wait C) Selective Repeat ARQ; Go-Back-N ARQ D) none of the above

Last Answer : Go-Back-N ARQ; Stop-and-Wait

Automatic repeat request error management mechanism is provided by ________ a. logical link control sublayer b. media access control sublayerc. network interface control sublayer d. application access control sublayer

Description : Automatic repeat request error management mechanism is provided by ________ a. logical link control sublayer b. media access control sublayer c. network interface control sublayer d. application access control sublayer

Last Answer : a. logical link control sublayer

Automatic repeat request error management mechanism is provided by ________ A. logical link control sublayer B. media access control sublayer C. network interface control sublayer D. application access control sublayer

Description : Automatic repeat request error management mechanism is provided by ________ A. logical link control sublayer B. media access control sublayer C. network interface control sublayer D. application access control sublayer

Last Answer : A. logical link control sublayer

Which consequences are more likely to occur during the frame transmission in StopandWait ARQ mechanism? a. Loss of frame or an acknowledgementb. Delay in an acknowledgement c. Normal operation d. All of the above

Description : Which consequences are more likely to occur during the frame transmission in StopandWait ARQ mechanism? a. Loss of frame or an acknowledgement b. Delay in an acknowledgement c. Normal operation d. All of the above

Last Answer : d. All of the above

Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Description : Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Last Answer : B. The approximation of the quantized signal

Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Description : Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Last Answer : The approximation of the quantized signal

Quantization noise is caused by A. binary coding techniques B. serial transmission errors C. the synchronization between encoder and decoder D. the approximation of the quantized signal

Description : Quantization noise is caused by A. binary coding techniques B. serial transmission errors C. the synchronization between encoder and decoder D. the approximation of the quantized signal

Last Answer : D. the approximation of the quantized signal

The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the same bandwidth. A. Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

Why stabilising resistor in REF or residual E/F scheme?

Description : Why stabilising resistor in REF or residual E/F scheme? 

Last Answer : Required against CT saturation under heavy through fault currents.  

_________can impair a signal. A) Attenuation B) Distortion C) Noise D) All of theabove

Description : _________can impair a signal. A) Attenuation B) Distortion C) Noise D) All of theabove

Last Answer : All of theabove

________ is a typeof transmission impairment in which the signal loses strength due to the different propagation speeds of each frequency that makes up the signal. A) Attenuation B) Distortion C) Noise D) Decibel

Description : ________ is a typeof transmission impairment in which the signal loses strength due to the different propagation speeds of each frequency that makes up the signal. A) Attenuation B) Distortion C) Noise D) Decibel

Last Answer : Distortion

________ is a typeof transmission impairment in which the signal loses strength due to theresistance of the transmission medium. A) Attenuation B) Distortion C) Noise D) Decibel

Description : ________ is a typeof transmission impairment in which the signal loses strength due to theresistance of the transmission medium. A) Attenuation B) Distortion C) Noise D) Decibel

Last Answer : Attenuation

A noise where foreign signal enters the path of the transmitted signal is called …… A. Impulse B. Inter modulation C. cross talk D. both b and c

Description : A noise where foreign signal enters the path of the transmitted signal is called …… A. Impulse B. Inter modulation C. cross talk D. both b and c

Last Answer : C. cross talk

Attenuation and noise can impair a signal. True False

Description : Attenuation and noise can impair a signal. True False

Last Answer : True

_______ control refers to aset of proceduresused torestrict the amount ofdata that the sender can send before waiting foracknowledgment. A) Flow B) Error C) Transmission D) none of the above

Description : _______ control refers to aset of proceduresused torestrict the amount ofdata that the sender can send before waiting foracknowledgment. A) Flow B) Error C) Transmission D) none of the above

Last Answer : Flow

Consider a CSMA/CD network that transmits data at a rate of 100 Mbps (108 bits per second) over a 1 km (kilometre) cable with no repeaters. If the minimum frame size required for this network is 1250 bytes, what is the signal speed (km/sec) in the cable? a. 8000 b. 10000 c. 16000 d. 20000

Description : Consider a CSMA/CD network that transmits data at a rate of 100 Mbps (108 bits per second) over a 1 km (kilometre) cable with no repeaters. If the minimum frame size required for this network is 1250 bytes, what is the signal speed (km/sec) in the cable? a. 8000 b. 10000 c. 16000 d. 20000

Last Answer : d. 20000

The term modem is a composite word that refers to the two functional entities that make up the device: asignal _______ and a signal _______. A) modulator; demodulator B) demodulator; modulator C) modern;demo D) none of the above

Description : The term modem is a composite word that refers to the two functional entities that make up the device: asignal _______ and a signal _______. A) modulator; demodulator B) demodulator; modulator C) modern;demo D) none of the above

Last Answer : modulator; demodulator

In accordance with Coast Guard Regulations (46 CFR), a steering gear feeder circuit from the emergency switchboard or alternate power supply must have the capacity for continuous operation of the rudder 15° side to side in not more than 60 seconds for a A. 1/4 hour B. 1/2 hour C. 1 hour D. 2 hours

Description : In accordance with Coast Guard Regulations (46 CFR), a steering gear feeder circuit from the emergency switchboard or alternate power supply must have the capacity for continuous operation of the rudder 15° side to side in not more than 60 seconds for a A. 1/4 hour B. 1/2 hour C. 1 hour D. 2 hours

Last Answer : Answer: B

Decision to stop testing should be based upon A. Successful use of specific test case design methodologies B. A percentage of coverage for each coverage category C. Rate of error detection falls below a specified threshold D. All of the above

Description : Decision to stop testing should be based upon A. Successful use of specific test case design methodologies B. A percentage of coverage for each coverage category C. Rate of error detection falls below a specified threshold D. All of the above

Last Answer : D. All of the above

______ can be applied whenthe bandwidth of a link (in hertz) is greater than the combined bandwidths of the signals to be transmitted. A) TDMB)FDMC)Both (a)or (b)D)Neither (a) or (b)

Description : ______ can be applied whenthe bandwidth of a link (in hertz) is greater than the combined bandwidths of the signals to be transmitted. A) TDM B) FDM C) Both (a)or (b) D) Neither (a) or (b)

Last Answer : FDM