who coined the term micro program in 1951. a. T.V. Wilkes b. MV. Wilkes c. S.V. Wilkes d. DV. Wilkes

who coined the term micro program in 1951.

a. T.V. Wilkes
b. MV. Wilkes
c. S.V. Wilkes
d. DV. Wilkes
by

1 Answer

Answer :

b. MV. Wilkes
by

Related questions

Which symbol will be used to denote an micro operation. a. (*) b. (v) c. Both d. None

Description : Which symbol will be used to denote an micro operation. a. (*) b. (v) c. Both d. None

Last Answer : b. (v)

Sequence of microinstructions is termed as micro program or a. Hardware b. Software c. Firmware d. None of these

Description : Sequence of microinstructions is termed as micro program or a. Hardware b. Software c. Firmware d. None of these

Last Answer : c. Firmware

The micro program is an written in microcode and stored in firmware which is also referred as___ | a. Interpreter and control memory b. Translator and control store c. Translator and control memory d. ‘Interpreter and Translator

Description : The micro program is an written in microcode and stored in firmware which is also referred as___ | a. Interpreter and control memory b. Translator and control store c. Translator and control memory d. ‘Interpreter and Translator

Last Answer : a. Interpreter and control memory

Which micro operations carry information from one register to another. a. Register transfer b. Arithmetic c. Logical d. — Allof these

Description : Which micro operations carry information from one register to another. a. Register transfer b. Arithmetic c. Logical d. — Allof these

Last Answer : a. Register transfer

Micro operation is shown as: a. RI->R2 b. R1<-R2

Description : Micro operation is shown as: a. RI->R2 b. R1

Last Answer : b. R1

Arithmetic operation are carried by such micro operation on stored numeric data available in a. Register b. Data c. Both d. None

Description : Arithmetic operation are carried by such micro operation on stored numeric data available in a. Register b. Data c. Both d. None

Last Answer : a. Register

Which operation are binary type, and are performed on bits string that is placed in register: a. Logical micro operation b. Arithmetic micro operation c. Both d. None

Description : Which operation are binary type, and are performed on bits string that is placed in register: a. Logical micro operation b. Arithmetic micro operation c. Both d. None

Last Answer : a. Logical micro operation

A micro operation every bit of a register is a: a. Constant b. Variable c. Both d. None

Description : A micro operation every bit of a register is a: a. Constant b. Variable c. Both d. None

Last Answer : b. Variable

Which operation is extremely useful in serial transfer of data: a. Logical micro operation b. Arithmetic micro operation c. Shift micro operation d. None of these

Description : Which operation is extremely useful in serial transfer of data: a. Logical micro operation b. Arithmetic micro operation c. Shift micro operation d. None of these

Last Answer : c. Shift micro operation

Which operation refer bitwise manipulation of contents of register: a. Logical micro operation b. Arithmetic micro operation c. Shift micro operation d. None of these

Description : Which operation refer bitwise manipulation of contents of register: a. Logical micro operation b. Arithmetic micro operation c. Shift micro operation d. None of these

Last Answer : a. Logical micro operation

IBM-360 type language is example which supporting _—___—sJanguage. a. Micro b. Macro c. Botha &b d. None of these

Description : IBM-360 type language is example which supporting _—___—sJanguage. a. Micro b. Macro c. Botha &b d. None of these

Last Answer : b. Macro

Each instruction is executed by set of micro operations termed as. a. Micro instructions b. Mini instructions c. Botha &b d. None of these

Description : Each instruction is executed by set of micro operations termed as. a. Micro instructions b. Mini instructions c. Botha &b d. None of these

Last Answer : a. Micro instructions

For each micro operation the control unit generates set of_ signals. a. Control b. Address c. Data d. None of these

Description : For each micro operation the control unit generates set of_ signals. a. Control b. Address c. Data d. None of these

Last Answer : a. Control

Compared to hardware, firmware is _ __to design micro programmed organization: a. Difficult b. Easier c. Both a& b d. None of these

Description : Compared to hardware, firmware is _ __to design micro programmed organization: a. Difficult b. Easier c. Both a& b d. None of these

Last Answer : b. Easier

The function of these microinstructions is to issue the micro orders to_ _ a. CPU b. Memory c. Register d. Accumulator

Description : The function of these microinstructions is to issue the micro orders to_ _ a. CPU b. Memory c. Register d. Accumulator

Last Answer : a. CPU

Micro-orders generate the_ __ address of operand and execute instruction and prepare for fetching next instruction from the main memory: a. Physical b. Effective c. Logical d. all of above

Description : Micro-orders generate the_ __ address of operand and execute instruction and prepare for fetching next instruction from the main memory: a. Physical b. Effective c. Logical d. all of above

Last Answer : b. Effective

A computer having writable control memory is known as_ a. Static micro programmable b. Dynamic micro programmable c. Botha & b d. None of these

Description : A computer having writable control memory is known as_ a. Static micro programmable b. Dynamic micro programmable c. Botha & b d. None of these

Last Answer : b. Dynamic micro programmable

Source statements consist of 5fields in microinstruction source code are: a. Lable b. Micro-ops c. CD-spec d. BR-spec e. Address f. All of these

Description : Source statements consist of 5fields in microinstruction source code are: a. Lable b. Micro-ops c. CD-spec d. BR-spec e. Address f. All of these

Last Answer : f. All of these

Who invented EDSAC? A) John v. Neumann B) J.P. Eckert and John Mauchley C) Maurice Wilkes D) Howard Aiken

Description : Who invented EDSAC? A) John v. Neumann B) J.P. Eckert and John Mauchley C) Maurice Wilkes D) Howard Aiken

Last Answer : Answer : C

By defining the _ __ register as last in first out stack the sequence can handle nested subroutines: a. S b. J ce. R d. T

Description : By defining the _ __ register as last in first out stack the sequence can handle nested subroutines: a. S b. J ce. R d. T

Last Answer : ce. R

“Stored Program” concept was developed by ______ (A) Maurice Wilkes (B) Von Neumann (C) M.H.A. Newman (D) None of the Above

Description : “Stored Program” concept was developed by ______ (A) Maurice Wilkes (B) Von Neumann (C) M.H.A. Newman (D) None of the Above

Last Answer : (B) Von Neumann

if noise voltage =120 mv and signal voltage = 80 v , S/N ratio in dB is?

Description : if noise voltage =120 mv and signal voltage = 80 v , S/N ratio in dB is?

Last Answer : Answers is the place to go to get the answers you need and to ask the questions you want

Which microprocessor has the control unit, memory unit and arithmetic and logic unit: a. Pentium IV processor b Pentium V processor c. Pentium III processor d. None of these

Description : Which microprocessor has the control unit, memory unit and arithmetic and logic unit: a. Pentium IV processor b Pentium V processor c. Pentium III processor d. None of these

Last Answer : a. Pentium IV processor

Potentiometer wire of length `1 m` is connected in series with `490 Omega` resistance and `2 V` battery. If `0.2 mV/cm` is the potential gradient, the

Description : Potentiometer wire of length `1 m` is connected in series with `490 Omega` resistance and `2 V` battery. If `0.2 mV/cm` is the potential gradient, the

Last Answer : Potentiometer wire of length `1 m` is connected in series with `490 Omega` resistance and `2 V` battery. If ... 7.9Omega` C. `5.9Omega` D. `6.9Omega`

A particle of mass m is moving along a straight path through the origin of coordinates with a velocity v. The angular momentum of the particle about the origin (a) mv (b) Depends on its distance from origin (c) Is zero (d) Changes from positive to negative as it passes through the origin

Description : A particle of mass m is moving along a straight path through the origin of coordinates with a velocity v. The angular momentum of the particle about the origin (a) mv (b) Depends on its distance from origin (c) Is zero (d) Changes from positive to negative as it passes through the origin

Last Answer : Ans:(c)

The potential difference across the gap of a spark plug ranges between a) 10-20 mV b) 10-20 V c) 10-20 kV d) 10-20 MV

Description : The potential difference across the gap of a spark plug ranges between a) 10-20 mV b) 10-20 V c) 10-20 kV d) 10-20 MV

Last Answer : ans a

For amplitude measurements, ___ scale is calibrated in either volts per centimeter (V/cm), or millivolts per centimeter (mV/cm)

Description : For amplitude measurements, ___ scale is calibrated in either volts per centimeter (V/cm), or millivolts per centimeter (mV/cm)

Last Answer : vertical

If the range of an analog transducer is 0 to 10 V, then for a resolution of 5 mV, the bits of ADC will be _____.

Description :  If the range of an analog transducer is 0 to 10 V, then for a resolution of 5 mV, the bits of ADC will be _____.

Last Answer :  If the range of an analog transducer is 0 to 10 V, then for a resolution of 5 mV, the bits of ADC will be 11.

The instruction fetch operation is initiated by loading the contents of program counter into the and sends _ request to memory: a. Memory register and read b. Memory register and write c. Data register and read d. Address register and read

Description : The instruction fetch operation is initiated by loading the contents of program counter into the and sends _ request to memory: a. Memory register and read b. Memory register and write c. Data register and read d. Address register and read

Last Answer : d. Address register and read

The contents of the program counter isthe __——__—oof the instruction to be run. a. Data b. Address c. Counter d. None of these

Description : The contents of the program counter isthe __——__—oof the instruction to be run. a. Data b. Address c. Counter d. None of these

Last Answer : b. Address

The instruction read from memory is then placed in the ___and contents of program counter is __ so that it contains the address of_ __ instruction in the program. a. Program counter, incremented and next b. Instruction register, incremented and previous c. Instruction register, incremented and next d. Address register, decremented and next

Description : The instruction read from memory is then placed in the ___and contents of program counter is __ so that it contains the address of_ __ instruction in the program. a. Program counter, ... incremented and previous c. Instruction register, incremented and next d. Address register, decremented and next

Last Answer : c. Instruction register, incremented and next

The control unit and arithmetic logic unit are know as the __ a. Central program unit b. Central processing unit

Description : The control unit and arithmetic logic unit are know as the __ a. Central program unit b. Central processing unit

Last Answer : b. Central processing unit

Which register holds the current instruction to be executed. a. Instruction register b. Program register 9 Control register a None of these

Description : Which register holds the current instruction to be executed. a. Instruction register b. Program register 9 Control register a None of these

Last Answer : a. Instruction register

Assembler works to convert assembly language program into machine language : a. Before the computer can execute it b. After the computer can execute it c. In between execution d. All of these

Description : Assembler works to convert assembly language program into machine language : a. Before the computer can execute it b. After the computer can execute it c. In between execution d. All of these

Last Answer : a. Before the computer can execute it

Assembly language program is called. a. Object program b. Source program c. Oriented program

Description : Assembly language program is called. a. Object program b. Source program c. Oriented program

Last Answer : b. Source program

In second pass, assembler creates _ in binary format for every instruction in program and then refers to the symbol table to giving every symbol an_ _ relating the segment. a. Code and program b. Program and instruction c. Code and offset d. All of these

Description : In second pass, assembler creates _ in binary format for every instruction in program and then refers to the symbol table to giving every symbol an_ _ relating the segment. a. Code and program b. Program and instruction c. Code and offset d. All of these

Last Answer : c. Code and offset

An assembler is a utility program that performs: a. Isometric translation b. Isomorphic translation c. Isochoric translation d. None of these

Description : An assembler is a utility program that performs: a. Isometric translation b. Isomorphic translation c. Isochoric translation d. None of these

Last Answer : b. Isomorphic translation

A program that links several programs is called: a. Linker b. Loader c. Translator d. None of these

Description : A program that links several programs is called: a. Linker b. Loader c. Translator d. None of these

Last Answer : a. Linker

contain library program have to be indicated to the loader. a. Externally defined b. Internally defined c. Executable file d. All of these

Description : contain library program have to be indicated to the loader. a. Externally defined b. Internally defined c. Executable file d. All of these

Last Answer : a. Externally defined

Itis the task of the __to locate externally defined symbols in programs, load them in to memory by placing their __ of symbols in calling program: a. Loader and name b. Linker and values c. Linker and name d. Loader and values

Description : Itis the task of the __to locate externally defined symbols in programs, load them in to memory by placing their __ of symbols in calling program: a. Loader and name b. Linker and values c. Linker and name d. Loader and values

Last Answer : d. Loader and values

which of the following are types of assembler entities: a. Absolute entities b. Relative entities c. Object program d. Allof these

Description : which of the following are types of assembler entities: a. Absolute entities b. Relative entities c. Object program d. Allof these

Last Answer : d. Allof these

A module contains machine code with specification on_ _ a. Relative addresses b. Absolute addresses c. Object program d. None of these

Description : A module contains machine code with specification on_ _ a. Relative addresses b. Absolute addresses c. Object program d. None of these

Last Answer : a. Relative addresses

function is used to transfer the control to end of a program which uses one argument( ) and takes value is zero for_ __ termination and non-zero for _termination: a. _ Exit( ) normal, abnormal b. Break, normal, abnormal Botha & b None of these

Description : function is used to transfer the control to end of a program which uses one argument( ) and takes value is zero for_ __ termination and non-zero for _termination: a. _ Exit( ) normal, abnormal b. Break, normal, abnormal Botha & b None of these

Last Answer : a. _ Exit( ) normal, abnormal

To design a program it requires __ os a. Program specification b. Code specification c. Instruction specification d. Problem specification

Description : To design a program it requires __ os a. Program specification b. Code specification c. Instruction specification d. Problem specification

Last Answer : a. Program specification

Testing helpstoensure_——_—of the program for use within a system. a. Quality, accuracy and except b. Quality, accuracy and acceptance c. Design, assurance and acceptance d. Quality, accuracy and development

Description : Testing helpstoensure_——_—of the program for use within a system. a. Quality, accuracy and except b. Quality, accuracy and acceptance c. Design, assurance and acceptance d. Quality, accuracy and development

Last Answer : b. Quality, accuracy and acceptance

An unstructured program uses a approach to solve problems: a. Linear b. Top down co Botha&b d. None of these

Description : An unstructured program uses a approach to solve problems: a. Linear b. Top down co Botha&b d. None of these

Last Answer : co Botha&b

Ina complex program, the overlaps: a. Branching b. Condition c. Botha &b d. None of these

Description : Ina complex program, the overlaps: a. Branching b. Condition c. Botha &b d. None of these

Last Answer : a. Branching

In_ instructions are followed one after the other in the preset order in which they appear within program: a. Sequence b Selection c. Break d. Iteration

Description : In_ instructions are followed one after the other in the preset order in which they appear within program: a. Sequence b Selection c. Break d. Iteration

Last Answer : a. Sequence

is a small program tested separately before combining with final program: a Module b. Block c. selection d. none of these

Description : is a small program tested separately before combining with final program: a Module b. Block c. selection d. none of these

Last Answer : a Module

___uses various symbols to represent function within program and is __ _representation: a. Flowchart, pictorial b. Algorithm, pictorial c. Pictorial, flowchart d. None of these

Description : ___uses various symbols to represent function within program and is __ _representation: a. Flowchart, pictorial b. Algorithm, pictorial c. Pictorial, flowchart d. None of these

Last Answer : a. Flowchart, pictorial