Vibrometer is designed with A. Low Frequency B. High Frequency C. Zero Frequency D. None of these

Vibrometer is designed with
A. Low Frequency
B. High Frequency
C. Zero Frequency
D. None of these
by

1 Answer

Answer :

A. Low Frequency
by

Related questions

From the following, which one is also known as low-frequency Transducer? (A) Stroboscope (B) Accelerometer (C) Vibrometer (D) None of the above

Description : From the following, which one is also known as low-frequency Transducer? (A) Stroboscope (B) Accelerometer (C) Vibrometer (D) None of the above

Last Answer : (C) Vibrometer

In vibrometer, the relative motion between the mass and vibrating body is converted into proportional ________. (A) current (B) voltage (C) resistance (D) ampere

Description : In vibrometer, the relative motion between the mass and vibrating body is converted into proportional ________. (A) current (B) voltage (C) resistance (D) ampere

Last Answer : (B) voltage

If the amplitude of harmonic motion is large, its frequency A) Will always be high B) Will always be less C) Can have any value D) Will be zero

Description : If the amplitude of harmonic motion is large, its frequency A) Will always be high B) Will always be less C) Can have any value D) Will be zero

Last Answer : C) Can have any value

What is meant by critical damping coefficient? * 1 point (A) Frequency of damped free vibrations is less than zero (B). The motion is a periodic in nature (C). Both a. and b. (D). None of the above

Description : What is meant by critical damping coefficient? * 1 point (A) Frequency of damped free vibrations is less than zero (B). The motion is a periodic in nature (C). Both a. and b. (D). None of the above

Last Answer : (C). Both a. and b.

What is meant by critical damping coefficient? A Frequency of damped free vibrations is less than zero B The motion is aperiodic in nature C Both a. and b. D None of the above

Description : What is meant by critical damping coefficient? A Frequency of damped free vibrations is less than zero B The motion is aperiodic in nature C Both a. and b. D None of the above

Last Answer : B The motion is aperiodic in nature

Which of the following statements is/are true? A. Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction B. Shaft vibrates with maximum frequency when rotors rotate in same direction C. Zero node behavior is observed in rotors rotating in opposite direction D. All of the above

Description : Which of the following statements is/are true? A. Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction B. Shaft vibrates with maximum frequency when rotors ... C. Zero node behavior is observed in rotors rotating in opposite direction D. All of the above

Last Answer : A. Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction

The number of natural frequency in two rotor system is A Zero B Infinite C Two D One

Description : The number of natural frequency in two rotor system is A Zero B Infinite C Two D One

Last Answer : C Two

In energy method for finding frequency of the system A The sum of kinetic and potential energy is constant B The sum of kinetic and potential energy is zero C Frequency cannot be determined by energy method D None of the mentioned

Description : In energy method for finding frequency of the system A The sum of kinetic and potential energy is constant B The sum of kinetic and potential energy is zero C Frequency cannot be determined by energy method D None of the mentioned

Last Answer : A The sum of kinetic and potential energy is constant

When a body moves with simple harmonic motion, the product of its periodic time and frequency is equal to A. Zero B. One C. π/2 D. 2π

Description : When a body moves with simple harmonic motion, the product of its periodic time and frequency is equal to A. Zero B. One C. π/2 D. 2π

Last Answer : B. One

At which frequency ratio, phase angle increases as damping factor increases? A. When frequency ratio is less than unity B. When frequency ratio is more than unity C. When frequency ratio is zero D. All of the above

Description : At which frequency ratio, phase angle increases as damping factor increases? A. When frequency ratio is less than unity B. When frequency ratio is more than unity C. When frequency ratio is zero D. All of the above

Last Answer : A. When frequency ratio is less than unity

Which of the following statements is/are true? A) Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction B) Shaft vibrates with maximum frequency when rotors rotate in same direction C) Zero node behavior is observed in rotors rotating in opposite direction D) All of the above

Description : Which of the following statements is/are true? A) Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction B) Shaft vibrates with maximum frequency when rotors ... C) Zero node behavior is observed in rotors rotating in opposite direction D) All of the above

Last Answer : A) Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction

Semi definite system having one of their natural frequency equal to A) Four B) Three C) Two D) Zero

Description : Semi definite system having one of their natural frequency equal to A) Four B) Three C) Two D) Zero

Last Answer : D) Zero

If ωmax is the frequency at which the peak amplitude occurs and ωn is the natural frequency of the system then In a forced vibration system with damping, the higher the damping, A) More will be the difference between ωn and ωmax B) Less will be the difference between ωn and ωmax C) The difference of ωn and ωmax is independent of damping in this system D) The difference between ωn and ωmax will be zero

Description : If ωmax is the frequency at which the peak amplitude occurs and ωn is the natural frequency of the system then In a forced vibration system with damping, the higher the damping, A) More will be ... and ωmax is independent of damping in this system D) The difference between ωn and ωmax will be zero

Last Answer : A) More will be the difference between ωn and ωmax

What is meant by critical damping coefficient? B ( A )Frequency of damped free vibrations is less than zero ( B )The motion is aperiodic in nature ( C )Both a. and b. (D)None of the above

Description : What is meant by critical damping coefficient? B ( A )Frequency of damped free vibrations is less than zero ( B )The motion is aperiodic in nature ( C )Both a. and b. (D)None of the above

Last Answer : ( B )The motion is aperiodic in nature

When the frequency of external exciting force is equal to the natural frequency of the vibration of the system A. The amplitude of vibration is zero B. The amplitude of vibration is significantly small C. The amplitude of vibration is very large D. The amplitude does not change

Description : When the frequency of external exciting force is equal to the natural frequency of the vibration of the system A. The amplitude of vibration is zero B. The amplitude of vibration is significantly small C. The amplitude of vibration is very large D. The amplitude does not change

Last Answer : C. The amplitude of vibration is very large

Which of the following statements is/are true? a. Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction b. Shaft vibrates with maximum frequency when rotors rotate in same direction c. Zero node behavior is observed in rotors rotating in opposite direction d. All of the above

Description : Which of the following statements is/are true? a. Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction b. Shaft vibrates with maximum frequency when rotors ... c. Zero node behavior is observed in rotors rotating in opposite direction d. All of the above

Last Answer : a. Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction

What is meant by critical damping coefficient? a. Frequency of damped free vibrations is less than zero b. The motion is aperiodic in nature c. Both a. and b. d. None of the above

Description : What is meant by critical damping coefficient? a. Frequency of damped free vibrations is less than zero b. The motion is aperiodic in nature c. Both a. and b. d. None of the above

Last Answer : b. The motion is aperiodic in nature

The accelerometer is used as a transducer to measure earthquake in Richter scale. Its design is based on the principle that A Its natural frequency is very low in comparison to the frequency of vibration B Its natural frequency is very high in comparison to the frequency of vibration C Its natural frequency is equal to the frequency of vibration D Measurement of vibratory motion is without any reference point

Description : The accelerometer is used as a transducer to measure earthquake in Richter scale. Its design is based on the principle that A Its natural frequency is very low in comparison to the frequency ... is equal to the frequency of vibration D Measurement of vibratory motion is without any reference point

Last Answer : C Its natural frequency is equal to the frequency of vibration

The accelerometer is used as a transducer to measure earthquake in Richter scale. Its design is based on the principle that a) its natural frequency is very low in comparison to the frequency of vibration b) its natural frequency is very high in comparison to the frequency of vibration c) its natural frequency is equal to the frequency of vibration d) measurement of vibratory motion is without any reference point

Description : The accelerometer is used as a transducer to measure earthquake in Richter scale. Its design is based on the principle that a) its natural frequency is very low in comparison to the frequency ... is equal to the frequency of vibration d) measurement of vibratory motion is without any reference point

Last Answer : c) its natural frequency is equal to the frequency of vibration

The accelerometer is used as a transducer to measure earthquake in Richter scale. Its design is based on the principle that ______. (A) its natural frequency is very low in comparison to the frequency of vibration (B) its natural frequency is very high in comparison to the frequency of vibration (C) its natural frequency is equal to the frequency of vibration (D) measurement of vibratory motion is without any reference poin

Description : The accelerometer is used as a transducer to measure earthquake in Richter scale. Its design is based on the principle that ______. (A) its natural frequency is very low in comparison to the ... is equal to the frequency of vibration (D) measurement of vibratory motion is without any reference poin

Last Answer : (C) its natural frequency is equal to the frequency of vibration

The accelerometer is used as a transducer to measure earthquake in Richter scale. Its design is based on the principle that a) its natural frequency is very low in comparison to the frequency of vibration b) its natural frequency is very high in comparison to the frequency of vibration c) its natural frequency is equal to the frequency of vibration d) measurement of vibratory motion is without any reference poin

Description : The accelerometer is used as a transducer to measure earthquake in Richter scale. Its design is based on the principle that a) its natural frequency is very low in comparison to the frequency ... is equal to the frequency of vibration d) measurement of vibratory motion is without any reference poin

Last Answer : c) its natural frequency is equal to the frequency of vibration

If the spring mass system with m and spring stiffness k is taken to very high altitude, the natural frequency of longitudinal vibrations * 1 point (A) increases (B) decreases (C) remain unchanged (D) may increase or decrease depending upon the value of the mass

Description : If the spring mass system with m and spring stiffness k is taken to very high altitude, the natural frequency of longitudinal vibrations * 1 point (A) increases (B) decreases (C) remain unchanged (D) may increase or decrease depending upon the value of the mass

Last Answer : (C) remain unchanged

If frequency of excitation of a forced vibration system with negligible damping is very close to natural frequency of the system, then the system will A) Execute harmonic motion of large amplitude B) Beat with a very high peak amplitude C) Perform aperiodic motion D) None of the above

Description : If frequency of excitation of a forced vibration system with negligible damping is very close to natural frequency of the system, then the system will A) Execute harmonic motion of large amplitude B) Beat with a very high peak amplitude C) Perform aperiodic motion D) None of the above

Last Answer : A) Execute harmonic motion of large amplitude

If the spring mass system with m and spring stiffness k is taken to very high altitude , the natural frequency of longitudinal vibrations A) Increases B) Decreases C) Remain unchanged D) May be increase or decrease depending upon the value of the mass

Description : If the spring mass system with m and spring stiffness k is taken to very high altitude , the natural frequency of longitudinal vibrations A) Increases B) Decreases C) Remain unchanged D) May be increase or decrease depending upon the value of the mass

Last Answer : C) Remain unchanged

f the spring displacement is high then the frequency of the spring increases. a) True b) False

Description : f the spring displacement is high then the frequency of the spring increases. a) True b) False

Last Answer : b) False

The speed at which the shaft runs so that the additional deflection of the shaft from the axis of rotation becomes ___________, is known as critical or whirling speed. (A) zero (B) minimum (C) maximum (D) infinite

Description : The speed at which the shaft runs so that the additional deflection of the shaft from the axis of rotation becomes ___________, is known as critical or whirling speed. (A) zero (B) minimum (C) maximum (D) infinite

Last Answer : (D) infinite

In vibration isolation system, if ω/ωn < 2, then for all values of damping factor, the transmissibility will be A less than unity B equal to unity C greater than unity D zero

Description : In vibration isolation system, if ω/ωn < 2, then for all values of damping factor, the transmissibility will be A less than unity B equal to unity C greater than unity D zero

Last Answer : C greater than unity

What is meant by node point? A. The point at which amplitude of vibration is maximum B. The point at which amplitude of vibration is minimum C. The point at which amplitude of vibration is zero D. None of the above

Description : What is meant by node point? A. The point at which amplitude of vibration is maximum B. The point at which amplitude of vibration is minimum C. The point at which amplitude of vibration is zero D. None of the above

Last Answer : C. The point at which amplitude of vibration is zero

Dynamic vibration absorber is suitable for A varying speed machines B constant speed machines C Zero speed range machines D None of the mentioned

Description : Dynamic vibration absorber is suitable for A varying speed machines B constant speed machines C Zero speed range machines D None of the mentioned

Last Answer : B constant speed machines

In semi-definite system one of the natural frequencies is A Zero B One C Two D Infinite

Description : In semi-definite system one of the natural frequencies is A Zero B One C Two D Infinite

Last Answer : A Zero

A system is said to be over damped if the damping factor for the system is A More than one B Less than one C Equal to one D Equal to zero

Description : A system is said to be over damped if the damping factor for the system is A More than one B Less than one C Equal to one D Equal to zero

Last Answer : A More than one

A system is said to be under damped if the damping factor for the system is A More than one B Less than one C Equal to one D Equal to zero

Description : A system is said to be under damped if the damping factor for the system is A More than one B Less than one C Equal to one D Equal to zero

Last Answer : B Less than one

A system is said to be critically damped if the damping factor for a vibrating system is A Zero B Less than one C One D More than one

Description : A system is said to be critically damped if the damping factor for a vibrating system is A Zero B Less than one C One D More than one

Last Answer : C One

The number of natural frequencies in case of cantilever is A Zero B One C Two D Infinite

Description : The number of natural frequencies in case of cantilever is A Zero B One C Two D Infinite

Last Answer : D Infinite

As per Energy Method, the summation of kinetic energy and potential energy must be ________ which is same at all the times. A. zero B. minimum C. maximum D. constant

Description : As per Energy Method, the summation of kinetic energy and potential energy must be ________ which is same at all the times. A. zero B. minimum C. maximum D. constant

Last Answer : D. constant

Dynamic vibration absorber is suitable for A) Constant speed machine B) Varying speed machine C) zero speed machine D) None of the above

Description : Dynamic vibration absorber is suitable for A) Constant speed machine B) Varying speed machine C) zero speed machine D) None of the above

Last Answer : A) Constant speed machine

As per Energy Method, the summation of kinetic energy and potential energy must D be ________ which is same at all the times. ( A ) zero ( B ) minimum ( C ) maximum ( D ) constant

Description : As per Energy Method, the summation of kinetic energy and potential energy must D be ________ which is same at all the times. ( A ) zero ( B ) minimum ( C ) maximum ( D ) constant

Last Answer : ( D ) constant

Dynamic vibration absorber is suitable for A. Constant speed machines B. Varying speed machines C. Zero speed range machines D. None of the above

Description : Dynamic vibration absorber is suitable for A. Constant speed machines B. Varying speed machines C. Zero speed range machines D. None of the above

Last Answer : A. Constant speed machines

In semidefinite system one of the natural frequencies is A. Zero B. Non-zero C. Infinite one D. One

Description : In semidefinite system one of the natural frequencies is A. Zero B. Non-zero C. Infinite one D. One

Last Answer : A. Zero

The number of natural frequencies in a two rotor system is A. Infinite B. Zero C. Two D. Four

Description : The number of natural frequencies in a two rotor system is A. Infinite B. Zero C. Two D. Four

Last Answer : C. Two

A node means a section where the amplitude of vibration is A. Maximum B. Half of the maximum C. Zero D. 1⁄4 of the maximum

Description : A node means a section where the amplitude of vibration is A. Maximum B. Half of the maximum C. Zero D. 1⁄4 of the maximum

Last Answer : C. Zero

A system is said to be overdamped if the damping factor is A. Equal to One B. Greater than One C. Less than one D. Equal to zero

Description : A system is said to be overdamped if the damping factor is A. Equal to One B. Greater than One C. Less than one D. Equal to zero

Last Answer : B. Greater than One

The system is said to be critically damped if the damping factor is A. Greater than one B. Equal to one C. Less than one D. Zero

Description : The system is said to be critically damped if the damping factor is A. Greater than one B. Equal to one C. Less than one D. Zero

Last Answer : B. Equal to one

The resultant motion of two Simple Harmonic Motions will be A. Simple Harmonic MotionB. Periodic Motion C. Projectile Motion D. Zero

Description : The resultant motion of two Simple Harmonic Motions will be A. Simple Harmonic MotionB. Periodic Motion C. Projectile Motion D. Zero

Last Answer : A. Simple Harmonic Motion

The number of degrees of freedom in simple spring mass system is A. Zero B. One C. Two D. Three

Description : The number of degrees of freedom in simple spring mass system is A. Zero B. One C. Two D. Three

Last Answer : B. One

In vibration isolation system, if ω/ω n < 2, then for all values of damping factor, the transmissibility will be a) less than unity b) equal to unity c) greater than unity d) zero

Description : In vibration isolation system, if ω/ω n < 2, then for all values of damping factor, the transmissibility will be a) less than unity b) equal to unity c) greater than unity d) zero

Last Answer : c) greater than unity

The response of an Undamped system under resonance will be a. very large b. infinity c. zero

Description : The response of an Undamped system under resonance will be a. very large b. infinity c. zero

Last Answer : b. infinity

As per Energy Method, the summation of kinetic energy and potential energy must be ________ which is same at all the times. (A) zero (B) minimum (C) maximum (D) constant

Description : As per Energy Method, the summation of kinetic energy and potential energy must be ________ which is same at all the times. (A) zero (B) minimum (C) maximum (D) constant

Last Answer : (D) constant

In vibration isolation system, if ω/ω n < 2, then for all values of damping factor, the transmissibility will be a) less than unity b) equal to unity c) greater than unity d) zero

Description : In vibration isolation system, if ω/ω n < 2, then for all values of damping factor, the transmissibility will be a) less than unity b) equal to unity c) greater than unity d) zero

Last Answer : c) greater than unity

n vibration isolation system, if ω/ω n is less than √2 , then for all values of the damping factor, the transmissibility will be a) less than unity b) equal to unity c) greater than unity d) zero

Description : n vibration isolation system, if ω/ω n is less than √2 , then for all values of the damping factor, the transmissibility will be a) less than unity b) equal to unity c) greater than unity d) zero

Last Answer : c) greater than unity