Classify the power amplifiers on the basis of operation and input/output waveforms.

Classify the power amplifiers on the basis of operation and input/output waveforms.
by

1 Answer

Answer :

Depending upon the operation and input/output waveforms power amplifiers are classified into following type.

1) Class A amplifier.

2) Class B amplifier.

3) Class C amplifier.

4) Class AB amplifier.

5) Class D amplifier
by

Related questions

Comment on the effect of negative feedback on the gain, input and output resistance of the feedback amplifiers.Describe the gain bandwidth product term used in this context and its importance.

Description : Comment on the effect of negative feedback on the gain, input and output resistance of the feedback amplifiers.Describe the gain bandwidth product term used in this context and its importance.

Last Answer : Effect of negative feedback: 1. Gain decreases with negative feedback. 2. Input resistance increases with negative feedback. 3. Output resistance decreases with negative feedback. Explanation ... feedback bandwidth increases which means it is stable output on more range of frequency.

Compare Class A ,Class B, Class C and class AB power amplifiers on the basis of: i)Angle of conduction ii)Efficiency iii)Position of operating pointing power dissipation iv)Distortion

Description : Compare Class A ,Class B, Class C and class AB power amplifiers on the basis of: i)Angle of conduction ii)Efficiency iii)Position of operating pointing power dissipation iv)Distortion

Last Answer : Compare Class A ,Class B, Class C and class AB power amplifiers on the basis of: i)Angle of conduction ii)Efficiency iii)Position of operating pointing power dissipation iv)Distortion

Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Description : Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Last Answer : During positive half-cycle of input, the secondary voltage VAB is positive, so diodes D1 and D2 forward biased and D3 and D4 reverse biased. The load current flows from terminal A ... smooth DC voltage appears across the load. The input and output waveforms are shown in the figure.

Explain stagger tuned amplifier with the help of waveforms.

Description : Explain stagger tuned amplifier with the help of waveforms.

Last Answer : Circuit Diagram: Above figure shows two-stage tuned voltage amplifier. The stagger tuning in this circuit, may be achieved by resonating the tuned circuits L1C1 and L2C2 to slightly different ... outside the pass-band. Because of the stagger tuning there is a loss of voltage gain.

State classification of Amplifiers.

Description : State classification of Amplifiers.

Last Answer : CLASSIFICATION OF AMPLIFIERS: A] Based on input signal 1. Small signal amplifiers 2. Large signal amplifiers B] Based on output signal 1. Voltage amplifier 2. Power amplifier C ... coupling 1. Direct coupled amplifiers 2. R-C Coupled amplifier 3. Transformer coupled amplifier

Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Description : Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Last Answer : Circuit diagram:- Input / Output waveforms:-

The waveforms shown below are the input and output of an overdrive

Description : The waveforms shown below are the input and output of an overdrive

Last Answer : a. Cutoff. b. Saturation.

Draw & describe working of bridge rectifier with its input output waveforms

Description : Draw & describe working of bridge rectifier with its input output waveforms

Last Answer : Four diodes are used. a)In positive half cycle Diodes D1 & D3 becomes forward biased they will conduct & current flows at that time D2 and D4 are reverse biased they will not ... at that time D1 and D3 are reverse biased they will not conduct. we get full cycle rectification.

Draw and describe working of series biased clipper with input output waveforms.

Description : Draw and describe working of series biased clipper with input output waveforms. 

Last Answer : Biased series positive clipper: Clipping of the signal takes place as soon as the input signal goes positive. If we want to change/adjust the clipping level of AC voltage, then external biasing voltage must be ... voltage must be used. The figure given below shows a biased (series) clipper.    

Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Description : Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Last Answer : Explanation: A centre- tap full wave rectifier drive produces the rectified voltage and it drives the LC filter. We know that the series inductor filter is preferred for low values of load resistance ( ... load RL. The output voltage waveforms are similar to that as shown in figure above.  

Draw the practical AM diode detector circuit. Sketch its input and output waveforms.

Description : Draw the practical AM diode detector circuit. Sketch its input and output waveforms. 

Last Answer : Practical AM diode detector 1. Skip distance:-Skip distance is defined as the shortest distance from a transmitter, measured along the surface of earth at which a sky wave of fixed frequency ... had taken place from a surface located at a greater height, called Virtual height of this layer.

Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier

Description : Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier 

Last Answer : Rectifier - This circuit convert AC signal into DC.

Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it.

Description : Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it. 

Last Answer : Circuit Diagram: Waveforms:

Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms.

Description : Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms. 

Last Answer : Operation : During positive half cycle of an AC supply, D1 will forward biased and current starts flowing through load. The output voltage is equal to +Vs. During negative half cycle of an AC ... output voltage is equal to +Vs. In this pulsating DC waveform will be obtained at the load. 

Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output impedance C. low input impedance, low gain and high output impedance D. low input impedance, high gain and low output impedance

Description : Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output ... gain and high output impedance D. low input impedance, high gain and low output impedance

Last Answer : Answer: A

Explain with circuit diagram and waveform the operation of class AB push pull power amplifier.

Description : Explain with circuit diagram and waveform the operation of class AB push pull power amplifier.

Last Answer : Class AB Push Pull Power Amplifier:  Circuit Diagram:  Circuit Decription: The circuit consists of two centre-tapped transformers T1 and T2, two identical transistors Q1 and Q2 , Resistor R and ... two halves & produces a full sine wave in the load resistor. Waveform :

Describe the operation of class-C type of power amplifier with the help of neat sketch.

Description : Describe the operation of class-C type of power amplifier with the help of neat sketch.

Last Answer : Circuit diagram: Operation: * Class C power amplifier is a type of amplifier where the transistor conducts for less than one half cycle of the input signal. Less than one ... resonant circuit oscillates in one frequency (generally the carrier frequency) all other frequencies are attenuated. 

Classify I.C. engine on the basis of cycle of operation and cylinder arrangement.

Description : Classify I.C. engine on the basis of cycle of operation and cylinder arrangement.

Last Answer : 1) Cycle of operation:- a) Otto cycle engine b) Diesel cycle engine c) Duel combustion cycle engine or semi- diesel cycle engine. 2) Arrangement of cylinder:- a) Vertical engine b) horizontal engine c) Radial engine d) V-engine e) Opposed cylinder engine 

Classify I. C. Engine on the basis of -Cycle of operation -Method of cooling

Description : Classify I. C. Engine on the basis of -Cycle of operation -Method of cooling

Last Answer : Classification of I. C. Engine on the basis of  -Cycle of operation: a) Otto cycle engine b) Diesel cycle engine c) Duel combustion engine or semi-diesel cycle engine -Method of cooling: a) air cooled engine b) water cooled engine 

Describe the operation of double tuned amplifier with the help of neat circuit diagram and mention its applications.

Description : Describe the operation of double tuned amplifier with the help of neat circuit diagram and mention its applications.

Last Answer : Circuit diagram: Operation:  *The signal to be amplified is applied at the input terminal through the coupling capacitor CC  *The resonant frequency of the tuned circuit L1 C1 is made equal ... : (i) Radio and T .V broadcasting as tuning circuit. (ii) Wireless communication system.

With the help of neat circuit diagram, explain the operation of voltage shunt type feedback amplifier.

Description : With the help of neat circuit diagram, explain the operation of voltage shunt type feedback amplifier.

Last Answer : Diagram:  Fig. shows common emitter transistor amplifier with a feedback resistor RF connected between its output and input terminals. This is collector to base biasing when the input signal is ... As IS = If + Ii it is shunt type therefore it voltage shunt negative feedback amplifier.

What waveform is the basis of all complex waveforms?

Description : What waveform is the basis of all complex waveforms?

Last Answer : The sine wave.

In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Description : In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Last Answer : The vertical-deflection plate.

For a class D commutation, answer the following: i) Explain the operation with circuit diagram. ii) Interpret with waveforms.

Description : For a class D commutation, answer the following: i) Explain the operation with circuit diagram. ii) Interpret with waveforms.

Last Answer : Class D commutation: This is also called as auxiliary commutation because it uses an auxiliary SCR to switch the charged capacitor across conducting SCR to turn it off. In this scheme, the main ... make SCR1 forward biased and keep ready for next triggering. The above cyclic process is repeated.

How are amplifiers classified according to the input?

Description : How are amplifiers classified according to the input?

Last Answer : 1. Small – signal amplifier 2. Large – signal amplifier

Define each of following terms of operational amplifiers i) Slew rate ii) Input offset voltage iii) Voltage gain iv) Input capacitance

Description : Define each of following terms of operational amplifiers i) Slew rate ii) Input offset voltage iii) Voltage gain iv) Input capacitance

Last Answer : i) Slew rate:- Maximum rate of change of o/p voltage per unit of time. It is express in volt/µsec.  ii) Input offset voltage:- The voltage that must be applied between two ... capacitance that can be measured at either be inverting or non-inverting terminal with other terminal connected to ground.

Why does my computer audio input and output get interference on a regular basis?

Description : Why does my computer audio input and output get interference on a regular basis?

Last Answer : I've also noticed this robot-ness when I've used Skype, and on a brand new macbook. It hasn't happened in a little bit, but I seem to remember it only happening on one speaker. Perhaps ... that corrupts the audio systemwide-or maybe a bug in the underlying audio library that gets revealed by Skype.

Material price, mix, usage and revised quantity variances are measured on _______ basis, whereas material yield variance is measured on _______ basis. A. Output, Input B. Output, Output C. Input, Output D. None of the above

Description : Material price, mix, usage and revised quantity variances are measured on _______ basis, whereas material yield variance is measured on _______ basis. A. Output, Input B. Output, Output C. Input, Output D. None of the above

Last Answer : C. Input, Output

Compare BJT common base configuration with common collector configuration on the basis of (i) Current gain (ii) Voltage gain (iii) Input impedance (iv) Output impedance

Description : Compare BJT common base configuration with common collector configuration on the basis of (i) Current gain (ii) Voltage gain (iii) Input impedance (iv) Output impedance

Last Answer : Parameter Common Base Common Collector Current gain Low (About 1) High (1+β) Voltage gain High 1  Input impedance  Low High Output impedance High Low

The operation represented by parallelograms. a) Input/Output b) Assignment c) Comparison d) Conditions

Description : The operation represented by parallelograms. a) Input/Output b) Assignment c) Comparison d) Conditions

Last Answer : Answer: a Explanation: The input/output operations are represented by parallelograms. They generally are used to display messages during input and output part of a program

Which are benefit of input/output interrupt: a. It is an external analogy to exceptions b. The processor initiates and perform all I/O operation c. The data is transferred into the memory through interrupt handler d. = Alllof these

Description : Which are benefit of input/output interrupt: a. It is an external analogy to exceptions b. The processor initiates and perform all I/O operation c. The data is transferred into the memory through interrupt handler d. = Alllof these

Last Answer : d. = Alllof these

If the output of a circuit needs to be a complete representation of one-half of the input signal, what class of operation is indicated?

Description : If the output of a circuit needs to be a complete representation of one-half of the input signal, what class of operation is indicated?

Last Answer : Class B operation.

Which of the following are the functions of operating system? i) recovering from errors ii) facilitating input/output iii) facilitating parallel operation iv) sharing hardware among users v) implementing user interface A) i, ii, ii, and v only B) i, ii, iii, and iv only C) ii, iii, iv and v only D) All i, ii, iii, iv and v

Description : Which of the following are the functions of operating system? i) recovering from errors ii) facilitating input/output iii) facilitating parallel operation iv) sharing hardware among users v) implementing user interface A) i, ii, ... only C) ii, iii, iv and v only D) All i, ii, iii, iv and v

Last Answer : D) All i, ii, iii, iv and v

In successive-approximation A/D converter, offset voltage equal to 1/2 LSB is added to the D/A converter’s output. This is done to (A) Improve the speed of operation. (B) Reduce the maximum quantization error. (C) Increase the number of bits at the output. (D) Increase the range of input voltage that can be converted

Description : In successive-approximation A/D converter, offset voltage equal to 1/2 LSB is added to the D/A converter's output. This is done to (A) Improve the speed of operation. (B) Reduce the maximum ... Increase the number of bits at the output. (D) Increase the range of input voltage that can be converted

Last Answer : (B) Reduce the maximum quantization error.

Define the term related to power amplifier. (i) Efficiency (ii) Voltage gain

Description : Define the term related to power amplifier. (i) Efficiency (ii) Voltage gain

Last Answer : (i) Efficiency: Efficiency of the power amplifier is defined as the ratio of maximum a.c. output power to the d.c. input power. Mathematically (ii) Voltage gain: Voltage gain of the power amplifier is defined as the ratio of output voltage to the input voltage. Mathematically,

Draw the circuit diagram of class AB power amplifier and describe its working.

Description : Draw the circuit diagram of class AB power amplifier and describe its working.

Last Answer : Circuit diagram: Circuit Description: The circuit consists of two center-tapped transformers T1 and T2, two identical transistors Q1 and Q2 , Resistor R and diode D. The DC voltage ... and Q2 conduct, as soon as input cross zero, negative sinusoidal voltage will appear across load.

Compare small signal amplifier with power amplifier

Description : Compare small signal amplifier with power amplifier

Last Answer : Parameters Small signal Amplifiers Power Amplifiers Amplification quantity It increases voltage into high resistance load. Hence small signal amplifiers are also called as voltage amplifiers. It ... Coupling R-C coupling Transformer coupling Power output low High

Classify industries on the basis of the nature of products Give one example of each. -Geography

Description : Classify industries on the basis of the nature of products Give one example of each. -Geography

Last Answer : On the basis of the nature of products, industries can be divided into two categories : 1. Heavy Industry: Use heavy and bulky raw material as iron ore and coal etc. Example : Iron ... . 2. Light Industry: Use light raw material. Example: . Pharmaceutical industry, chemical industry etc.

Classify rainfed farming in India into two categories on the basis of adequacy of soil moisture. -Geography

Description : Classify rainfed farming in India into two categories on the basis of adequacy of soil moisture. -Geography

Last Answer : Rainfed fanning is classified on the basis of adequacy of soil moisture into two (i) dryland farming and (ii) wetland farming: Dry land farming: (i) It is confined to the ... ) Water intensive crops are grown-rice, jute, and sugarcane and practise aquaculture in the fresh water bodies.

Classify industries on the basis of the capital investment. -Geography

Description : Classify industries on the basis of the capital investment. -Geography

Last Answer : The industries are classified on the following basis: 1. On the basis of raw material used. 2. According to the utility of the product. 3. On the basis of the capital investment. 4. ... limit keeps changing, but at present, the maximum investment allowed in the small-scale industry is 1 crore.

Classify minerals into two groups on the basis of chemical and physical properties and give one example of minerals of each group. -Geography

Description : Classify minerals into two groups on the basis of chemical and physical properties and give one example of minerals of each group. -Geography

Last Answer : Minerals are classified on the basis of their physical properties and chemical properties such as: Metallic Minerals Metallic minerals are those that are rich in metals and a source to procure a variety of ... is rich in building stones i.e. sandstone, granite, marble, fuller's earth, and gypsum

Classify resources on the basis of development with examples. -SST 10th

Description : Classify resources on the basis of development with examples. -SST 10th

Last Answer : Classification of resources on the basis of development is as follows: 1. Potential Resources: Resources which are found in a region, but have not been utilised are called potential resources. For example, the ... the water in the dams, forests, etc. is a reserve which can be used in the future.

Classify resources on the basis of ownership with examples? -SST 10th

Description : Classify resources on the basis of ownership with examples? -SST 10th

Last Answer : 1. Individual Resources: These are owned privately by individuals. Many farmers own land which is allotted to them by government against the payment of revenue. Urban people own houses, ... open ocean and no individual country can utilise these without the permission of international institutions.

Classify industries on the basis of their main role. How are they different from each other? -SST 10th

Description : Classify industries on the basis of their main role. How are they different from each other? -SST 10th

Last Answer : According to their main role: . Basic or key industries which supply their products or raw materials to manufacture other goods, e.g., iron and steel and coppers melting, aluminium smelting. . ... produce goods for direct use by consumers - sugar, toothpaste, paper, sewing machines, fans etc.|

Classify industries on the basis of source of raw material. How are they different from each other? -SST 10th

Description : Classify industries on the basis of source of raw material. How are they different from each other? -SST 10th

Last Answer : On the basis of sources of raw material industries are classified as: . Agro based: Agro based industries draw their raw materials from agricultural products. For example, Textiles, Sugar, ... from minerals. For example, Iron and Steel industries, cement, machine holes, petrochemicals, etc.

Classify industries on the basis of bulk and weight of raw materials and finished goods. -SST 10th

Description : Classify industries on the basis of bulk and weight of raw materials and finished goods. -SST 10th

Last Answer : Industries are classified on the basis of the weight of raw materials and finished goods in the following manner: . Heavy Industries: These industries use heavy raw materials and also produce heavy ... light goods such as electrical industries, e.g., watches, electric bulbs, paint brushes, etc.

Classify industries on basis of capital investment. -SST 10th

Description : Classify industries on basis of capital investment. -SST 10th

Last Answer : Following is the classification of industries on the basis of capital investment: 1.Small-scale Industries: A small-scale industry is defined with reference to the maximum investment allowed on the assets of a ... more than rupees 1 crore on any industry, then it is known as a large-scale industry.

Classify industries on the basis of source of raw materials used. -SST 10th

Description : Classify industries on the basis of source of raw materials used. -SST 10th

Last Answer : On the basis of source of raw materials used, industries are classified into: 1.Agro-based industries: These industries are based on agricultural raw material, e.g., cotton, jute, silk, rubber ... mineral-based industries, e.g., iron and steel, cement, aluminium, machine tools, petrochemicals, etc.

Classify industries on the basis of their main role. -SST 10th

Description : Classify industries on the basis of their main role. -SST 10th

Last Answer : 1.Basic or key industries: These industries supply their product or raw materials to manufacture other goods; e.g., iron and steel, copper smelting and aluminium smelting. 2.Consumer industries: These are ... for direct use by consumers; e.g., sugar, toothpaste, paper, sewing machines, fans, etc.