The waveforms shown below are the input and output of an overdrive

The waveforms shown below are the input and output of an overdrive
by

1 Answer

Answer :

a. Cutoff.  
 b. Saturation.
by

Related questions

In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Description : In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Last Answer : The vertical-deflection plate.

Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Description : Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Last Answer : During positive half-cycle of input, the secondary voltage VAB is positive, so diodes D1 and D2 forward biased and D3 and D4 reverse biased. The load current flows from terminal A ... smooth DC voltage appears across the load. The input and output waveforms are shown in the figure.

Draw & describe working of bridge rectifier with its input output waveforms

Description : Draw & describe working of bridge rectifier with its input output waveforms

Last Answer : Four diodes are used. a)In positive half cycle Diodes D1 & D3 becomes forward biased they will conduct & current flows at that time D2 and D4 are reverse biased they will not ... at that time D1 and D3 are reverse biased they will not conduct. we get full cycle rectification.

Draw and describe working of series biased clipper with input output waveforms.

Description : Draw and describe working of series biased clipper with input output waveforms. 

Last Answer : Biased series positive clipper: Clipping of the signal takes place as soon as the input signal goes positive. If we want to change/adjust the clipping level of AC voltage, then external biasing voltage must be ... voltage must be used. The figure given below shows a biased (series) clipper.    

Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Description : Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Last Answer : Explanation: A centre- tap full wave rectifier drive produces the rectified voltage and it drives the LC filter. We know that the series inductor filter is preferred for low values of load resistance ( ... load RL. The output voltage waveforms are similar to that as shown in figure above.  

Draw the practical AM diode detector circuit. Sketch its input and output waveforms.

Description : Draw the practical AM diode detector circuit. Sketch its input and output waveforms. 

Last Answer : Practical AM diode detector 1. Skip distance:-Skip distance is defined as the shortest distance from a transmitter, measured along the surface of earth at which a sky wave of fixed frequency ... had taken place from a surface located at a greater height, called Virtual height of this layer.

Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Description : Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Last Answer : Circuit diagram:- Input / Output waveforms:-

Classify the power amplifiers on the basis of operation and input/output waveforms.

Description : Classify the power amplifiers on the basis of operation and input/output waveforms.

Last Answer : Depending upon the operation and input/output waveforms power amplifiers are classified into following type. 1) Class A amplifier. 2) Class B amplifier. 3) Class C amplifier. 4) Class AB amplifier. 5) Class D amplifier

Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier

Description : Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier 

Last Answer : Rectifier - This circuit convert AC signal into DC.

Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it.

Description : Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it. 

Last Answer : Circuit Diagram: Waveforms:

Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms.

Description : Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms. 

Last Answer : Operation : During positive half cycle of an AC supply, D1 will forward biased and current starts flowing through load. The output voltage is equal to +Vs. During negative half cycle of an AC ... output voltage is equal to +Vs. In this pulsating DC waveform will be obtained at the load. 

In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?

Description : In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?

Last Answer : 60 millivolts.

In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?

Description : In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?

Last Answer : 50 millivolts.

With the inputs shown below, what will be the output of S1, S2, and C2?

Description : With the inputs shown below, what will be the output of S1, S2, and C2?

Last Answer : MSD of the sum.

Waveforms are described in terms of what two functions?

Description : Waveforms are described in terms of what two functions?

Last Answer : Amplitude and time.

Waveforms are described in terms of what two functions?

Description : Waveforms are described in terms of what two functions?

Last Answer : Amplitude and time.

which waveforms on the left have a resultant wave of zero, and what is indicated by these waves?

Description : which waveforms on the left have a resultant wave of zero, and what is indicated by these waves?

Last Answer : 2 and 6 have zero resultant wave and they indicate that the incident and reflected waves are 180 degrees out of phase at all parts.

Name two instruments used to analyze waveforms.

Description : Name two instruments used to analyze waveforms.

Last Answer : Oscilloscope and spectrum analyzer.

What waveform is the basis of all complex waveforms?

Description : What waveform is the basis of all complex waveforms?

Last Answer : The sine wave.

Which portion of a sine-wave input is retained in the output of a series-negative limiter?

Description : Which portion of a sine-wave input is retained in the output of a series-negative limiter?

Last Answer : Positive.

Which portion of a sine-wave input is retained in the output of a series-positive limiter?

Description : Which portion of a sine-wave input is retained in the output of a series-positive limiter?

Last Answer : Negative.

What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?

Description : What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?

Last Answer : -5 volts.

In the basic transistor amplifier discussed earlier, what is the relationship between the polarity of the input and output signals?

Description : In the basic transistor amplifier discussed earlier, what is the relationship between the polarity of the input and output signals?

Last Answer : The signals are opposite in polarity or 180 degrees out of phase with each other.

Which transistor configuration provides a phase reversal between the input and output signals?

Description : Which transistor configuration provides a phase reversal between the input and output signals?

Last Answer : Common emitter.

A two-input X-OR gate will produce a HIGH output when the inputs are at what logic levels?

Description : A two-input X-OR gate will produce a HIGH output when the inputs are at what logic levels?

Last Answer : . One or the other of the inputs must be HIGH, but not both at the same time.

The input and output signals of a JFET amplifier have what phase relationship?

Description : The input and output signals of a JFET amplifier have what phase relationship?

Last Answer : They are 180 degrees out of phase.

select the correct response from the choices given in the parentheses. Q-20. In a closed-loop configuration the output signal is determined by (the input signal, the feedback signal, both).

Description : select the correct response from the choices given in the parentheses. Q-20. In a closed-loop configuration the output signal is determined by (the input signal, the feedback signal, both).

Last Answer : Both the input signal and the feedback signal.

If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?

Description : If If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?

Last Answer : 200 millivolts.

If the input signals are 180 degrees out of phase with each other, what will be the peak-to-peak amplitude of the output signals?

Description : If the input signals are 180 degrees out of phase with each other, what will be the peak-to-peak amplitude of the output signals?

Last Answer : Each output signal will be 100 millivolts.

If the input signals are in phase, what will be the peak-to peak amplitude of the output signals?

Description : If the input signals are in phase, what will be the peak-to peak amplitude of the output signals?

Last Answer : 0 volts (the input signals will "cancel out").

If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Last Answer : 200 millivolts. A-18. a. Differential amplifier

If the differential amplifier is configured with a single input and differential outputs, what will the output signals be?

Description : If the differential amplifier is configured with a single input and differential outputs, what will the output signals be?

Last Answer : Each output will be a sine wave with a peak-to-peak amplitude of 100 millivolts. The output signals will be 180 degrees out of phase with each other.

If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Last Answer : . A different shape than the input signals but larger in amplitude.

If only one input signal is used with a difference amplifier, what will the output signal be?

Description : If only one input signal is used with a difference amplifier, what will the output signal be?

Last Answer : Equal in shape and frequency to the input signal; larger in amplitude than the input signal; half as large in amplitude as when two input signals were used that were 180 degrees out of phase.

If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?

Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?

Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than

. If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?

Description : . If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?

Last Answer : No output (the signals will "cancel out").

What two transistor amplifier configurations are combined in the single-transistor, two-input, single-output difference amplifier?

Description : What two transistor amplifier configurations are combined in the single-transistor, two-input, single-output difference amplifier?

Last Answer : Common emitter (CE) and common base (CB)

When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.

Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.

Last Answer : An increase.

What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Description : What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Last Answer : Pulse width

What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Description : What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Last Answer : Pulse width.

If the inductance of a choke-input filter is increased, will the output ripple voltage amplitude (Er) increase or decrease?

Description : If the inductance of a choke-input filter is increased, will the output ripple voltage amplitude (Er) increase or decrease?

Last Answer : Decrease.

When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease in the resistance of the regulating device.

Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease in the resistance of the regulating device.

Last Answer : Increase.

Which type of optical splitter (Y-coupler or T-coupler) splits only a small amount of power from the input fiber to one of the output fibers?

Description : Which type of optical splitter (Y-coupler or T-coupler) splits only a small amount of power from the input fiber to one of the output fibers?

Last Answer : T-coupler

What is the logarithmic ratio between the input and output

Description : What is the logarithmic ratio between the input and output

Last Answer : dBm

How are the input and output directional couplers in a twt connected to the helix?

Description : How are the input and output directional couplers in a twt connected to the helix?

Last Answer : The directional couplers are not physically connected to the helix.

How does dc bias added to the input signal correct the distortion in the output signal?

Description : How does dc bias added to the input signal correct the distortion in the output signal?

Last Answer : The dc bias moves the input signal away from the step in the magnetism curve. This prevents the input signal from crossing the zero-point of the magnetism curve.

If the rf amplifier discussed has an 80 milliwatt input, what would be the maximum output?

Description : If the rf amplifier discussed has an 80 milliwatt input, what would be the maximum output?

Last Answer : 800 watts.

What is the output Boolean expression for an AND gate with A and B as inputs when the B input is inverted?

Description : What is the output Boolean expression for an AND gate with A and B as inputs when the B input is inverted?

Last Answer : AB

In a properly functioning circuit, can both the input and output of an inverter be HIGH at the same time?

Description : In a properly functioning circuit, can both the input and output of an inverter be HIGH at the same time?

Last Answer : No.