Two shafts A and B are made of same material. The diameters of shaft A and B are dA and dB respectively. The ratio of torque transmitted by shaft A to that of shaft B will be (A) dA/dB- (B) (dA/dB-)2 (C) (dA/dB-)3 (D) (dA/dB-)4

Two shafts A and B are made of same material. The diameters of shaft A and B are dA and dB respectively. The ratio of

torque transmitted by shaft A to that of shaft B will be

(A) dA/dB-

(B) (dA/dB-)2

(C) (dA/dB-)3

(D) (dA/dB-)4
by

1 Answer

Answer :

(C) (dA/dB-)3
by

Related questions

Two shafts A and B are made of same material. The diameter of shaft A is twice that of B. The torque transmitted by shaft A will be (A) Twice that of B (B) Four times that of B (C) Eight times that of B (D) Sixteen times that of B

Description : Two shafts A and B are made of same material. The diameter of shaft A is twice that of B. The torque transmitted by shaft A will be (A) Twice that of B (B) Four times that of B (C) Eight times that of B (D) Sixteen times that of B

Last Answer : (C) Eight times that of B

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Last Answer : b) 51.6N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Last Answer : a) 27mm

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Last Answer : c) 41666.7N

Splines are used if, (A) The power to be transmitted is high (B) The torque to be transmitted is high (C) The speed is high (D) There is relative motion between shaft and hub

Description : Splines are used if, (A) The power to be transmitted is high (B) The torque to be transmitted is high (C) The speed is high (D) There is relative motion between shaft and hub

Last Answer : (D) There is relative motion between shaft and hub

Two shafts A and B are made of the same material. The diameter of the shaft A is twice as that of shaft B. The power transmitted by the shaft A will be ........... of shaft B. (a) twice (b) four times (c) eight times (d) sixteen times

Description : Two shafts A and B are made of the same material. The diameter of the shaft A is twice as that of shaft B. The power transmitted by the shaft A will be ........... of shaft B. (a) twice (b) four times (c) eight times (d) sixteen times

Last Answer : (c) eight times

Ratio of diameters of two shafts joined in series is 2. If the two shafts have the same material and the same length the ratio of their shear stresses is a. 2 b. 4 c. 8 d. 16

Description : Ratio of diameters of two shafts joined in series is 2. If the two shafts have the same material and the same length the ratio of their shear stresses is a. 2 b. 4 c. 8 d. 16

Last Answer : c. 8

Ratio of diameters of two shafts joined in series is 2. If the two shafts have the same material and the same length the ratio of their angles of twist is a. 2 b. 4 c. 8 d. 16

Description : Ratio of diameters of two shafts joined in series is 2. If the two shafts have the same material and the same length the ratio of their angles of twist is a. 2 b. 4 c. 8 d. 16

Last Answer : d. 16

Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Description : Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Last Answer : d. Only torque transmitting capacity of the shaft is same

A knuckle joint is unsuitable for two rotating shafts, which transmit torque a) True b) False

Description : A knuckle joint is unsuitable for two rotating shafts, which transmit torque a) True b) False

Last Answer : a) True

Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (a) Inner race

The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Description : The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Last Answer : a. 15/16

For two shafts joined in parallel, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Description : For two shafts joined in parallel, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Last Answer : b. Angle of twist

For two shafts joined in series, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Description : For two shafts joined in series, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Last Answer : c. torque

The shafts will have same strength on the basis of torsional rigidity, if (A) Diameter and length of both shafts is same (B) Material of both shafts is same (C) Angle of twist for both shafts is same (D) All of above conditions are satisfied

Description : The shafts will have same strength on the basis of torsional rigidity, if (A) Diameter and length of both shafts is same (B) Material of both shafts is same (C) Angle of twist for both shafts is same (D) All of above conditions are satisfied

Last Answer : (D) All of above conditions are satisfied

For same weight, same material, same length a. Solid shaft is always stronger than a hollow shaft b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of hollow shaft c. Strength of both the shafts in equal d. Strength of a solid shaft is always weaker and the strength ratio will depend upon Do/Di of hollow shaft

Description : For same weight, same material, same length a. Solid shaft is always stronger than a hollow shaft b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of ... of a solid shaft is always weaker and the strength ratio will depend upon Do/Di of hollow shaft

Last Answer : b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of hollow shaft

Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Description : Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Last Answer : b) 1102.8N

Entire torque is transmitted by friction in the clamp coupling. a) True b) False

Description : Entire torque is transmitted by friction in the clamp coupling. a) True b) False

Last Answer : b) False

Entire torque is transmitted by friction in the clamp coupling. a) True b) False

Description : Entire torque is transmitted by friction in the clamp coupling. a) True b) False

Last Answer : b) False

Which of the following are not true for petroff’s equation? a) Shaft is considered concentric with the bearing b) Bearing is subjected to light load c) Is used to find coefficient of friction d) Frictional torque is given by fpr2l

Description : Which of the following are not true for petroff’s equation? a) Shaft is considered concentric with the bearing b) Bearing is subjected to light load c) Is used to find coefficient of friction d) Frictional torque is given by fpr2l

Last Answer : d) Frictional torque is given by fpr2l

The distribution of the forces along the length of key fitted in a shaft (A) Varies linearly (B) Is uniform throughout (C) Varies exponentially, being more near the torque-input end (D) Varies exponentially, being less near the torque-input end

Description : The distribution of the forces along the length of key fitted in a shaft (A) Varies linearly (B) Is uniform throughout (C) Varies exponentially, being more near the torque-input end (D) Varies exponentially, being less near the torque-input end

Last Answer : (C) Varies exponentially, being more near the torque-input end

The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T

Description : The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T

Last Answer : (A) T/2

If n is the ratio of internal and external diameters of a hollow shaft, the ratio of the weight of the hollow shaft and that of solid shaft of same strength, will be (A) (1 - n²)/(1 - n²)1/2 (B) (1 - n²)/(1 - n 4 )2/3 (C) (1 + n 3 )/(1 + n 4 )1/2 (D) (1 + n 1 )/(1 + n 4 )2/3

Description : If n is the ratio of internal and external diameters of a hollow shaft, the ratio of the weight of the  hollow shaft and that of solid shaft of same strength, will be  (A) (1 - n²)/(1 - n²)1/2 (B) (1 - n²)/(1 - n 4 ... (1 + n 4 )1/2 (D) (1 + n 1 )/(1 + n 4 )2/3

Last Answer : (B) (1 - n²)/(1 - n 4 )2/3

Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Last Answer : d) 53mm

Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Last Answer : d) 53mm

For same length, same material, same length a. Weight of solid shaft is less than weight of hollow shaft b. Weight of solid shaft is more than weight of hollow shaft c. Weight of hollow and solid shafts will be same d. Sometime more sometime less

Description : For same length, same material, same length a. Weight of solid shaft is less than weight of hollow shaft b. Weight of solid shaft is more than weight of hollow shaft c. Weight of hollow and solid shafts will be same d. Sometime more sometime less

Last Answer : b. Weight of solid shaft is more than weight of hollow shaft

For two shafts in series or having different diameters for two parts of length a. T = T1 + T2 b. T = T1 = T2 c. T = T1 – T2 d. T = (T1.T2)^1/2

Description : For two shafts in series or having different diameters for two parts of length a. T = T1 + T2 b. T = T1 = T2 c. T = T1 – T2 d. T = (T1.T2)^1/2

Last Answer : b. T = T1 = T2

A shaft turns at 150 rpm under a torque of 1500 N-m. Power transmitted is (a) 15p kW (b) 10p kW (c) 7.5p kW (d) 5p kW (IES 1999) Hint: P = 2pNT/60

Description : A shaft turns at 150 rpm under a torque of 1500 N-m. Power transmitted is (a) 15p kW (b) 10p kW (c) 7.5p kW (d) 5p kW (IES 1999) Hint: P = 2pNT/60

Last Answer : (c) 7.5p kW

The torque transmitted by a hollow shaft of outer diameter (D) and inner diameter (d) (a)π/4fs(D2-d2)/D (b) π/4fs(D3-d3)/D (c) π/4fs(D4-d4)/D (d) π/4fs(D4-d4)/D

Description : The torque transmitted by a hollow shaft of outer diameter (D) and inner diameter (d) (a)π/4fs(D2-d2)/D (b) π/4fs(D3-d3)/D (c) π/4fs(D4-d4)/D (d) π/4fs(D4-d4)/D

Last Answer : (c) π/4fs(D4-d4)/D

The torque transmitted by a solid shaft is (a)π/4fsd3 (b) π/16fsd3 (c) π/32fsd3 (d) π/64fsd3

Description : The torque transmitted by a solid shaft is (a)π/4fsd3 (b) π/16fsd3 (c) π/32fsd3 (d) π/64fsd3

Last Answer : (b) π/16fsd3

Oldham coupling i used to connect two shafts having intersecting axes. a) True b) False

Description : Oldham coupling i used to connect two shafts having intersecting axes. a) True b) False

Last Answer : b) False

A coupling is a mechanical device that temporarily joins two rotating shafts to each other. a) True b) False

Description : A coupling is a mechanical device that temporarily joins two rotating shafts to each other. a) True b) False

Last Answer : b) False

A flange coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Have lateral misalignment D. Whose axes intersect at a small angle

Description : A flange coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Have lateral misalignment D. Whose axes intersect at a small angle

Last Answer : A. Which are perfectly aligned

Oldham coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Which have lateral misalignment D. Whose axes intersect at a small angle

Description : Oldham coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Which have lateral misalignment D. Whose axes intersect at a small angle

Last Answer : C. Which have lateral misalignment

A universal coupling is used to connect two shafts A. Which are not in exact alignment B. Which are perfectly aligned C. Whose axes intersect at a small angle D. Have lateral misalignment

Description : A universal coupling is used to connect two shafts A. Which are not in exact alignment B. Which are perfectly aligned C. Whose axes intersect at a small angle D. Have lateral misalignment

Last Answer : C. Whose axes intersect at a small angle

Oldham coupling i used to connect two shafts having intersecting axes. a) True b) False

Description : Oldham coupling i used to connect two shafts having intersecting axes. a) True b) False

Last Answer : b) False

A coupling is a mechanical device that temporarily joins two rotating shafts to each other. a) True b) False

Description : A coupling is a mechanical device that temporarily joins two rotating shafts to each other. a) True b) False

Last Answer : b) False

Keyed joints never lead to stress concentration on shafts. a) True b) False

Description : Keyed joints never lead to stress concentration on shafts. a) True b) False

Last Answer : b) False

Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Description : Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Last Answer : (d) combined thrust and radial loads at high speed

Which one of the following types of bearings is employed in shafts of gearboxes of automobiles? [IES-1999] (a) Hydrodynamic journal bearings (b) Multi-lobed journal bearings (c) Antifriction bearings (d) Hybrid journal bearings

Description : Which one of the following types of bearings is employed in shafts of gearboxes of automobiles? [IES-1999] (a) Hydrodynamic journal bearings (b) Multi-lobed journal bearings (c) Antifriction bearings (d) Hybrid journal bearings

Last Answer : (c) Antifriction bearings

Flexible shafts have ______ rigidity in bending moment. a) High b) Low c) Very high d) Extremely low

Description : Flexible shafts have ______ rigidity in bending moment. a) High b) Low c) Very high d) Extremely low

Last Answer : b) Low

Flexible shafts have _______ rigidity in torsion making them flexible. a) Low b) High c) Very high d) Infinitely small

Description : Flexible shafts have _______ rigidity in torsion making them flexible. a) Low b) High c) Very high d) Infinitely small

Last Answer : b) High

Solid shafts are used in epicyclic gearboxes. a) True b) False

Description : Solid shafts are used in epicyclic gearboxes. a) True b) False

Last Answer : b) False

Which of the following act on shafts? a) Torsional moment b) Bending Moment c) Both torsional and bending d) None of the mentioned

Description : Which of the following act on shafts? a) Torsional moment b) Bending Moment c) Both torsional and bending d) None of the mentioned

Last Answer : c) Both torsional and bending

Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) None of the listed

Description : Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) None of the listed

Last Answer : b) Tensile

Flexible shafts have ______ rigidity in bending moment. a) High b) Low c) Very high d) Extremely low

Description : Flexible shafts have ______ rigidity in bending moment. a) High b) Low c) Very high d) Extremely low

Last Answer : b) Low

Solid shafts are used in epicyclic gearboxes. a) True b) False

Description : Solid shafts are used in epicyclic gearboxes. a) True b) False

Last Answer : b) False

Which of the following act on shafts? a) Torsional moment b) Bending Moment c) Both torsional and bending d) None of the mentioned

Description : Which of the following act on shafts? a) Torsional moment b) Bending Moment c) Both torsional and bending d) None of the mentioned

Last Answer : c) Both torsional and bending