Description : -For two shafts in parallel or for two concentric shafts a. T = T1 + T2 b. T = T1 = T2 c. T = T1 – T2 d. T = (T1.T2)^1/2
Last Answer : a. T = T1 + T2
Description : Ratio of diameters of two shafts joined in series is 2. If the two shafts have the same material and the same length the ratio of their shear stresses is a. 2 b. 4 c. 8 d. 16
Last Answer : c. 8
Description : Ratio of diameters of two shafts joined in series is 2. If the two shafts have the same material and the same length the ratio of their angles of twist is a. 2 b. 4 c. 8 d. 16
Last Answer : d. 16
Description : 18.The total extension of a taper rod of length ‘L’ and end diameters ‘D1’ and ‘D2’, subjected to a load (P), is given of a. 4PL/ΠE. D1D2 b. 3PL/ΠE. D1D2 c. 2PL/ΠE. D1D2 d. PL/ΠE.D1D2 Where E=Young’s modulus of elasticity
Last Answer : a. 4PL/ΠE. D1D2
Description : Equivalent bending moment in a shaft subjected to axial load P, torque T and bending moment M is (a) Meq = 0.5 [M + (M2 + T2)0.5]0.5 (b) Meq = 0.5 [M + (M2 + T2)0.5] (c) Meq = ( M2 + T2)0.5 (d) None
Last Answer : (b) Meq = 0.5 [M + (M2 + T2)0.5]
Description : Equivalent torque in a shaft subjected to axial load P, torque T and bending moment M is (a) Teq = (Pa2 + M2 + T2) (b) Teq = (Pa2 + M2 + T2)0.5 (c)Teq = ( M2 + T2)0.5 (d) None
Last Answer : c)Teq = ( M2 + T2)0.5
Description : For two shafts joined in series, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.
Last Answer : c. torque
Description : The relation governing the torsional torque in circular shafts is a. T/r=τ/l=Gθ/J b. T/J=τ/r=Gθ/l c. T/J=τ/l=Gθ/r d. T/l=τ/r=Gθ/J
Last Answer : b. T/J=τ/r=Gθ/l
Description : The shafts will have same strength on the basis of torsional rigidity, if (a) diameter and length of both shafts is same (b) material of both shafts is same (c) angle of twist for both shafts is same (d) all of above conditions are satisfied
Last Answer : (d) all of above conditions are satisfied
Description : For same length, same material, same length a. Weight of solid shaft is less than weight of hollow shaft b. Weight of solid shaft is more than weight of hollow shaft c. Weight of hollow and solid shafts will be same d. Sometime more sometime less
Last Answer : b. Weight of solid shaft is more than weight of hollow shaft
Description : For same weight, same material, same length a. Solid shaft is always stronger than a hollow shaft b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of ... of a solid shaft is always weaker and the strength ratio will depend upon Do/Di of hollow shaft
Last Answer : b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of hollow shaft
Description : S1 and S2 are the draw downs in an observation well at times t1 and t2 after pumping. For discharge Q and coefficient of transmissibility T, the relationship, is (A) S2 - S1 = (2.3Q/ ) log10 (t2/t1) (B) S2 - S1 ... - S1 = (2.3Q/4 ) loge (t2/t1) (D) S2 - S1 = (2.3Q/4 ) loge (t1/t2
Last Answer : (B) S2 - S1 = (2.3Q/4 ) log10 (t2/t1)
Description : Efficiency of a Carnot engine working between temperatures T1 and T2(T1 < T) is (A) (T2- T1)/T2 (B) (T2- T1)/T1 (C) (T1- T2)/T2 (D) (T1- T2)/T1
Last Answer : (A) (T2- T1)/T2
Description : Which of the following is the Ideal gas law (equation)? A. V/T = K B. V= k*(1/P) C. P1/T1 = P2/T2 D. PV = nRT
Last Answer : PV = nRT
Description : The clock period is denoted by: a. T p b. T1+T2+T3-------+T n c. Pt d. None of these
Last Answer : a. T p
Description : Let x1(t) and x2(t) be periodic with fundamental periods T1 and T2 respectively. Under what condition be the sum x(t) = x1(t) + x2(t) be periodic ? (A) Only for T1 = T2 (B) Always periodic (C) For T1/T2 equal to a rational number (D) Not periodic
Last Answer : Let x1(t) and x2(t) be periodic with fundamental periods T1 and T2 respectively. Under what condition be the sum x(t) = x1(t) + x2(t) be periodic ? (A) Only for T1 = T2 (B) Always periodic (C) For T1/T2 equal to a rational number (D) Not periodic
Description : The ratio of strengths of solid to hollow shafts, both having outside diameter D and hollow having inside diameter D/2, in torsion, is a.1/4 b. 1/2 c. 1/16 d. 15/16
Last Answer : d. 15/16
Description : A gas having a volume of100 ft³ at 27ºC is expanded to 120 ft³by heated at constant pressure to what temperature has it been heated to have this new volume? a. 87°C b. 85°C c. 76°C d. 97°C t2= T2–T1
Last Answer : 87°C
Description : The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7
Last Answer : a. 15/16
Description : The ratio of equilibrium constants (Kp2/Kp1) at two different temperatures is given by (A) (R/∆H) (1/T1- 1/T2) (B) (∆H/R) (1/T1- 1/T2) (C) (∆H/R) (1/T2- 1/T1) (D) (1/R) (1/T1- 1/T2)
Last Answer : (B) (∆H/R) (1/T1- 1/T2)
Description : The equilibrium constant for a chemical reaction at two different temperatures is given by (A) Kp2/Kp1 = - (∆H/R) (1/T2- 1/T1) (B) Kp2/Kp1 = (∆H/R) (1/T2- 1/T1) (C) Kp2/Kp1 = ∆H (1/T2- 1/T1) (D) Kp2/Kp1 = - (1/R) (1/T2- 1/T1)
Last Answer : (A) Kp2/Kp1 = - (∆H/R) (1/T2- 1/T1)
Description : Consider the following Entity-Relationship (E-R) diagram and three possible relationship sets (I, II and III) for this E-R diagram: If different symbols stand for different values (e.g., t1 is definitely not equal to t2 ... diagram ? (A) I only (B) I and II only (C) II only (D) I, II and III
Last Answer : (A) I only
Description : Two shafts will have equal strength, if (a) diameter of both the shafts is same (b) angle of twist of both the shafts is same (c) material of both the shafts is same (d) twisting moment of both the shafts is same
Last Answer : d) twisting moment of both the shafts is same
Description : Two shafts A and B are made of the same material. The diameter of the shaft A is twice as that of shaft B. The power transmitted by the shaft A will be ........... of shaft B. (a) twice (b) four times (c) eight times (d) sixteen times
Last Answer : (c) eight times
Description : Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same
Last Answer : d. Only torque transmitting capacity of the shaft is same
Description : For two shafts joined in parallel, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.
Last Answer : b. Angle of twist
Description : In shafts with keyways the allowable stresses are usually ------------ proportional to the twisting moment. a.25% b. 50% c. 75% d. 95%
Last Answer : c. 75%
Description : Flexible shafts have ______ rigidity in bending moment. a) High b) Low c) Very high d) Extremely low
Last Answer : b) Low
Description : Flexible shafts have ___ rigidity in torsion making them flexible. a) Low b) High c) Very high d) Infinitely small
Last Answer : b) High
Description : Solid shafts are used in epicyclic gearboxes. a) True b) False
Last Answer : b) False
Description : The design of shafts made of brittle materials is based on (a) Guest’s theory (b) Rankine’s theory (c) St. Venant’s theory (d) Von Mises Theory
Last Answer : (b) Rankine’s theory
Description : Which of the following act on shafts? a) Torsional moment b) Bending Moment c) Both torsional and bending d) None of the mentioned
Last Answer : c) Both torsional and bending
Description : It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting
Last Answer : b) Tensile
Description : .The shafts are designed on the basis of (a) Rigidity (b) Strength (c) Both of these (d) Either of these
Last Answer : (c) Both of these
Description : The following option is correct a. There is neither advantage nor disadvantage in transmitting power at high speed b. There is advantage in transmitting power at high speeds c. There is ... There is advantage in transmitting power at high speed provided shafts are made of high speed steel
Last Answer : b. There is advantage in transmitting power at high speeds
Description : Which of the following is incorrect? a. In torsion equation, we use mean torque b. In torsion equation, we use maximum torque c. Many shafts are designed under combined bending and torsion load d. Shafts are also designed for torsional rigidity
Last Answer : a. In torsion equation, we use mean torque
Description : The shafts are designed on the basis of a. strength and rigidity. b. ductility. c. malleablility. d. resilience.
Last Answer : a. strength and rigidity.
Description : The shafts are made of a. mild steel b. alloy steel c. copper alloys d. cast iron.
Last Answer : d. cast iron.
Description : Two shafts A and B are made of same material. The diameters of shaft A and B are dA and dB respectively. The ratio of torque transmitted by shaft A to that of shaft B will be (A) dA/dB- (B) (dA/dB-)2 (C) (dA/dB-)3 (D) (dA/dB-)4
Last Answer : (C) (dA/dB-)3
Description : Heat transfer by radiation between two bodies at T1 & T2 and in an ambient temperature of Ta °C depends on (A) T1 - T2 (B) T1 - Ta (C) T2 - Ta (D) None of these
Last Answer : (D) None of these
Description : For the same draw down in two observations wells at distances r1 and r2, the times after start of pumping are t1 and t2 hours respectively. The relation which holds good is (A) t2 = r2/r1 × t1 (B) t2 = (r2/r1)² × t1 (C) t2 = (r2/r1)3 × t1 (D) t2 = (r2/r1) × t1 2
Last Answer : (B) t2 = (r2/r1)² × t1
Description : For heat engine operating between two temperatures (T1>T2), what is the maximum efficiency attainable? A. Eff = 1 – (T2/T1) B. Eff = 1 - (T1/T2) C. Eff = T1 - T2 D. Eff = 1 - (T2/T1)^2
Last Answer : Eff = 1 – (T2/T1)
Description : The most efficient heat engine that can operate between two temperature reservoirs T1 and T2 is: w) jet engine x) internal combustion engine y) Carnot engine (pron: car-no) z) steam engine
Last Answer : ANSWER: Y -- CARNOT ENGINE
Description : Let the time taken to switch between user mode and kernel mode of execution be T1 while time taken to switch between two user processes be T2. Which of the following is correct? (A) T1 < T2 (B) T1 > T2 (C) T1 = T2 (D) Nothing can be said about the relation between T1 and T2.
Last Answer : (A) T1 < T2
Description : Why does CSF appears to be dark in T1 and white in T2?
Last Answer : I think that it is because the two types of MRI detirmine to color differently. T1 determines color based on spin-lattice relaxation time, while T2 determine color based on spin-spin relation time. Both ... dark. Since cerebrospinal fluid is mostly water, it shows up dark in T1 and light in T2.
Description : What is the difference between T1 and T2 mri scans?
Last Answer : Wikipedia has some stuff to get you going: http://en.wikipedia.org/wiki/MRI#Basic_MRI_scans
Description : If w is the angular velocity of the pulley and T1 and T2 are tensions of driving and driven side then power transmitted equals a.(T1 + T2) w b.(T1 + 2T2) w c.107 dynes d.(T1 - T2) w e.wT1
Last Answer : d. (T1 - T2) w
Description : Let R be a relation defined on the set A of all triangles such that R = {(T1, T2) : T1 is similar to T2}. Then R is -Maths 9th
Last Answer : (d) An equivalence relation.Every triangle is similar to itself, so (T1, T1) ∈ R ⇒ R is reflexive. (T1, T2) ∈ R ⇒ T1 ~ T2 ⇒T2 ~ T1, ⇒ (T2, T1) ∈ R ⇒ R is symmetrictransitive. ∴ R is an equivalence relation.
Description : What digital carrier transmits a digital signal at 274.176 Mbps? A. T1 B. T3 C. T2 D. T4
Last Answer : D. T4
Description : What carrier system multiplexes 96 voice band channels into a single 6.312 Mbps data signal? A. T1 carrier system B. T2 carrier system C. T1C carrier system D. T3 carrier system
Last Answer : B. T2 carrier system