The distribution of the forces along the length of key fitted in a shaft (A) Varies linearly (B) Is uniform throughout (C) Varies exponentially, being more near the torque-input end (D) Varies exponentially, being less near the torque-input end

The distribution of the forces along the length of key fitted in a shaft

(A) Varies linearly

(B) Is uniform throughout

(C) Varies exponentially, being more near the torque-input end

(D) Varies exponentially, being less near the torque-input end
by

1 Answer

Answer :

(C) Varies exponentially, being more near the torque-input end
by

Related questions

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Last Answer : b) 51.6N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

In case of an ideal solution, the total vapor pressure varies __________ with the composition expressed as mole fraction, (A) Inversely (B) Linearly (C) Exponentially (D) None of these

Description : In case of an ideal solution, the total vapor pressure varies __________ with the composition expressed as mole fraction, (A) Inversely (B) Linearly (C) Exponentially (D) None of these

Last Answer : (B) Linearly

In an isothermal atmosphere, the pressure (A) Decreases linearly with elevation (B) Remain constant (C) Varies in the same way as the density (D) Increases exponentially with elevation

Description : In an isothermal atmosphere, the pressure (A) Decreases linearly with elevation (B) Remain constant (C) Varies in the same way as the density (D) Increases exponentially with elevation

Last Answer : Answer: Option C

The concentration of A in a first order reaction, A → B, decreases (A) Linearly with time (B) Exponentially with time (C) Very abruptly towards the end of the reaction (D) Logarithmically with time

Description : The concentration of A in a first order reaction, A → B, decreases (A) Linearly with time (B) Exponentially with time (C) Very abruptly towards the end of the reaction (D) Logarithmically with time

Last Answer : (B) Exponentially with time

Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Last Answer : d) 53mm

Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm

Last Answer : d) 53mm

The standard length for square or flat key in terms of shaft diameter (D) is, (A) d (B) 2d (C) 1.5d (D) 2.5d

Description : The standard length for square or flat key in terms of shaft diameter (D) is, (A) d (B) 2d (C) 1.5d (D) 2.5d

Last Answer : (C) 1.5d

The following assumption is not true in the theory of pure torsion: (A) The twist along the shaft is uniform (B) The shaft is of uniform circular section throughout (C) Cross-section of the shaft, which is plane before twist remains plane after twist (D) All radii get twisted due to torsion

Description : The following assumption is not true in the theory of pure torsion:  (A) The twist along the shaft is uniform  (B) The shaft is of uniform circular section throughout  (C) Cross- ... , which is plane before twist remains plane after twist  (D) All radii get twisted due to torsion 

Last Answer : (D) All radii get twisted due to torsion 

Which of the following are not true for petroff’s equation? a) Shaft is considered concentric with the bearing b) Bearing is subjected to light load c) Is used to find coefficient of friction d) Frictional torque is given by fpr2l

Description : Which of the following are not true for petroff’s equation? a) Shaft is considered concentric with the bearing b) Bearing is subjected to light load c) Is used to find coefficient of friction d) Frictional torque is given by fpr2l

Last Answer : d) Frictional torque is given by fpr2l

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Last Answer : a) 27mm

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Last Answer : c) 41666.7N

Two shafts A and B are made of same material. The diameter of shaft A is twice that of B. The torque transmitted by shaft A will be (A) Twice that of B (B) Four times that of B (C) Eight times that of B (D) Sixteen times that of B

Description : Two shafts A and B are made of same material. The diameter of shaft A is twice that of B. The torque transmitted by shaft A will be (A) Twice that of B (B) Four times that of B (C) Eight times that of B (D) Sixteen times that of B

Last Answer : (C) Eight times that of B

Splines are used if, (A) The power to be transmitted is high (B) The torque to be transmitted is high (C) The speed is high (D) There is relative motion between shaft and hub

Description : Splines are used if, (A) The power to be transmitted is high (B) The torque to be transmitted is high (C) The speed is high (D) There is relative motion between shaft and hub

Last Answer : (D) There is relative motion between shaft and hub

Two shafts A and B are made of same material. The diameters of shaft A and B are dA and dB respectively. The ratio of torque transmitted by shaft A to that of shaft B will be (A) dA/dB- (B) (dA/dB-)2 (C) (dA/dB-)3 (D) (dA/dB-)4

Description : Two shafts A and B are made of same material. The diameters of shaft A and B are dA and dB respectively. The ratio of torque transmitted by shaft A to that of shaft B will be (A) dA/dB- (B) (dA/dB-)2 (C) (dA/dB-)3 (D) (dA/dB-)4

Last Answer : (C) (dA/dB-)3

The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T

Description : The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T

Last Answer : (A) T/2

Velocity distribution for flow between two fixed parallel plates (A) Varies parabolically across the section (B) Is constant over the entire cross-section (C) Is zero at the plates and increases linearly to the mid-plane (D) None of these

Description : Velocity distribution for flow between two fixed parallel plates (A) Varies parabolically across the section (B) Is constant over the entire cross-section (C) Is zero at the plates and increases linearly to the mid-plane (D) None of these

Last Answer : (A) Varies parabolically across the section

Sluice valves are fitted in a distribution system (A) Along straight length of pipes at suitable intervals (B) At the junctions of the pipes (C) At the branching off points of sub-mains (D) All the above

Description : Sluice valves are fitted in a distribution system (A) Along straight length of pipes at suitable intervals (B) At the junctions of the pipes (C) At the branching off points of sub-mains (D) All the above

Last Answer : (D) All the above

Consider the following statements: Mitra’s hyperbolic transition design is based on the principle that : 1. Flow depth in the canal, as well as the discharge, is constant 2. width of the canal varies along with the discharge 3. Rate of change of velocity per unit length of transition is constant throughout the length of the transition. Which of these statements are correct ? a) 1, 2 and 3 b) 1 and 2 only c) 2 and 3 only d) 1 and 3 only

Description : Consider the following statements: Mitra's hyperbolic transition design is based on the principle that : 1. Flow depth in the canal, as well as the discharge, is constant 2. width of the canal varies along with the discharge 3. Rate ... a) 1, 2 and 3 b) 1 and 2 only c) 2 and 3 only d) 1 and 3 only

Last Answer : d) 1 and 3 only

For a fluid rotating at constant angular velocity about vertical axis as a rigid body, the pressure intensity varies as the (A) Square of the radial distance (B) Radial distance linearly (C) Inverse of the radial distance(D) Elevation along vertical direction

Description : For a fluid rotating at constant angular velocity about vertical axis as a rigid body, the pressure intensity varies as the (A) Square of the radial distance (B) Radial distance linearly (C) Inverse of the radial distance (D) Elevation along vertical direction

Last Answer : (A) Square of the radial distance

In under damped vibrating system, the amplitude of vibration ______. (A) decreases linearly with time (B) increases linearly with time (C) decreases exponentially with time (D) increases exponentially with time

Description : In under damped vibrating system, the amplitude of vibration ______. (A) decreases linearly with time (B) increases linearly with time (C) decreases exponentially with time (D) increases exponentially with time

Last Answer : (C) decreases exponentially with time

Viscosity of a liquid decreases __________ with rise in temperature. (A) Exponentially (B) Linearly(C) Logarithmically(D) None of these

Description : Viscosity of a liquid decreases __________ with rise in temperature. (A) Exponentially (B) Linearly (C) Logarithmically (D) None of these

Last Answer : (C) Logarithmically

In the slow start phase of the TCP congestion control algorithm, the size of the congestion window a. does not increase b. increases linearly c. increases quadratically d. increases exponentially

Description : In the slow start phase of the TCP congestion control algorithm, the size of the congestion window a. does not increase b. increases linearly c. increases quadratically d. increases exponentially

Last Answer : d. increases exponentially

With the increase in depth, the hydrostatic pressure in an un-accelerated incompressible fluid (in a constant gravitational field) (A) Decreases (B) Increases linearly (C) Increases exponentially (D) Remain constant

Description : With the increase in depth, the hydrostatic pressure in an un-accelerated incompressible fluid (in a constant gravitational field) (A) Decreases (B) Increases linearly (C) Increases exponentially (D) Remain constant

Last Answer : (B) Increases linearly

Volume change for unimolecular type first order reaction as shown in the bellow figure, increases __________ with time. (A) Linearly (B) Exponentially (C) Parabolically (D) Logarithmically

Description : Volume change for unimolecular type first order reaction as shown in the bellow figure, increases __________ with time. (A) Linearly (B) Exponentially (C) Parabolically (D) Logarithmically

Last Answer : (B) Exponentially

The value of a property decreases __________ with time in straight line method of determining depreciation. (A) Linearly (B) Non-linearly (C) Exponentially (D) Logarithmically

Description : The value of a property decreases __________ with time in straight line method of determining depreciation. (A) Linearly (B) Non-linearly (C) Exponentially (D) Logarithmically

Last Answer : A) Linearly

first order chemical reaction, the concentration of the reactant decreases __________ with time. (A) Linearly (B) Exponentially (C) Logarithmically (D) Inversely

Description : first order chemical reaction, the concentration of the reactant decreases __________ with time. (A) Linearly (B) Exponentially (C) Logarithmically (D) Inversely

Last Answer : (A) Linearly

With increase in steam pressure, its specific volume decreases (A) Rapidly first and then slowly (B) Linearly (C) Slowly first and then rapidly (D) Exponentially

Description : With increase in steam pressure, its specific volume decreases (A) Rapidly first and then slowly (B) Linearly (C) Slowly first and then rapidly (D) Exponentially

Last Answer : Option A

Saddle key is transmit power or torque through friction resistant only A. True B. False

Description : Saddle key is transmit power or torque through friction resistant only A. True B. False

Last Answer : A. True

Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed

Description : Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed

Last Answer : b) Radial

Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed

Description : Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed

Last Answer : b) Radial

In case of sunk key, (A) The keyway is cut in the shaft only (B) The keyway is cut in the hub only (C) The keyway is cut in both the shaft and the hub (D) None of the above

Description : In case of sunk key, (A) The keyway is cut in the shaft only (B) The keyway is cut in the hub only (C) The keyway is cut in both the shaft and the hub (D) None of the above

Last Answer : (C) The keyway is cut in both the shaft and the hub

While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component

Description : While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component

Last Answer : (C) Key is the weakest component

The type of key used when the gear is required to slide on the shaft is (A) Sunk key (B) Feather key (C) Woodruff key (D) Kennedy key

Description : The type of key used when the gear is required to slide on the shaft is (A) Sunk key (B) Feather key (C) Woodruff key (D) Kennedy key

Last Answer : (B) Feather key

A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal

Description : A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal

Last Answer : a) Thrust

A radial bearing supports the load that acts along the axis of the shaft. a) True b) False

Description : A radial bearing supports the load that acts along the axis of the shaft. a) True b) False

Last Answer : b) False

In a shaft rotated by a couple, the shear force varies (A) From zero at the centre to a maximum at the circumference (B) From minimum at the centre of maximum at the circumference (C) From maximum at the centre to zero at the circumference (D) Equally throughout the section

Description : In a shaft rotated by a couple, the shear force varies (A) From zero at the centre to a maximum at the circumference (B) From minimum at the centre of maximum at the circumference (C) From maximum at the centre to zero at the circumference (D) Equally throughout the section

Last Answer : (A) From zero at the centre to a maximum at the circumference

Magnitude of shear stress induced in a shaft due to applied torque varies from a. Maximum at centre to zero at circumference. b. Maximum at centre to minimum (not-zero) at circumference. c. Zero at centre to maximum at circumference. d. Minimum (not zero) at centre to maximum at circumference.

Description : Magnitude of shear stress induced in a shaft due to applied torque varies from a. Maximum at centre to zero at circumference. b. Maximum at centre to minimum (not-zero) at circumference. c. Zero at centre to maximum at circumference. d. Minimum (not zero) at centre to maximum at circumference.

Last Answer : c. Zero at centre to maximum at circumference.

The key in the form of semi-circular disk of uniform thickness is called, (A) Sunk key (B) Feather key (C) Woodruff key (D) Kennedy key

Description : The key in the form of semi-circular disk of uniform thickness is called, (A) Sunk key (B) Feather key (C) Woodruff key (D) Kennedy key

Last Answer : (C) Woodruff key

Which of the following assumptions are made in torsion theory? a. Shaft is perfectly straight b. Material of the shaft is heterogeneous c. Twist cannot be uniform along the length of the shaft d. Shaft is perfectly curve

Description : Which of the following assumptions are made in torsion theory? a. Shaft is perfectly straight b. Material of the shaft is heterogeneous c. Twist cannot be uniform along the length of the shaft d. Shaft is perfectly curve v

Last Answer : a. Shaft is perfectly straight b. Material of the shaft is heterogeneous

The shear stress varies from centre to the surface of the shaft with (a) Uniform rate (b) Varying rate (c) Remains same (d) None of these

Description : The shear stress varies from centre to the surface of the shaft with (a) Uniform rate (b) Varying rate (c) Remains same (d) None of these

Last Answer : (a) Uniform rate

If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Last Answer : b) 140mm

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Last Answer : b) 41.2mm

Standard length of shaft is a ....... A. 5 meter B. 6 meter C. 7 meter D. All of these

Description : Standard length of shaft is a ....... A. 5 meter B. 6 meter C. 7 meter D. All of these

Last Answer : D. All of these

If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Last Answer : b) 140mm

For the same material, length and given torque, a hollow shaft weighs……………… a solid shaft. (a) Less than (b) More than (c) Equal to (d) None of these

Description : For the same material, length and given torque, a hollow shaft weighs……………… a solid shaft. (a) Less than (b) More than (c) Equal to (d) None of these

Last Answer : (a) Less than

For the same material, length and given torque a hoolow shaft weighs ---------- a solid shaft. a. less than b. more than. c. equal to d. not equal to.

Description : For the same material, length and given torque a hoolow shaft weighs ---------- a solid shaft. a. less than b. more than. c. equal to d. not equal to.

Last Answer : a. less than

Fitted bearing must be partial bearing. a) True b) No c) No lubricating space is required d) Can’t be stated

Description : Fitted bearing must be partial bearing. a) True b) No c) No lubricating space is required d) Can’t be stated

Last Answer : a) True

In a 2700 m race around a round track of length 300m, abi and kabi meet at the end of the 3rd minute, for the first time after the start of the race. All the runners maintain uniform speed throughout the race. If abi runs at twice the speed of the kabi. Find the time taken by abi to finish the race. a) 27 mints b) 32 mints c) 5 mints d) 23 mints

Description : In a 2700 m race around a round track of length 300m, abi and kabi meet at the end of the 3rd minute, for the first time after the start of the race. All the runners maintain uniform speed throughout the race. ... time taken by abi to finish the race. a) 27 mints b) 32 mints c) 5 mints d) 23 mints

Last Answer : A As, abi is twice as fast as the kabi, abi would have completed two rounds by the time kabi completes one round. And that is their second meeting. Their first meeting takes place after the abi ... 300m ⇒He takes 2700/300 *3 =27 mints Hence he takes 27 minutes to finish the race.